Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (46) (entfernen)
Sprache
- Englisch (46) (entfernen)
Schlagworte
- Simulation (46) (entfernen)
Institut
The main focus of the benefit estimation of advanced safety systems with a warning interface by simulation is on the driver. The driver is the only link between the algorithm of the safety system and the vehicle, which makes the setup of a driver model for such simulations very important. This paper describes an approach for the use of a statistical driver model in simulation. It also gives an outlook on further work on this topic. The build-up process of the model suffices with a distribution of reaction times and a distribution of reaction intensities. Both were combined in different scenarios for every driver. Each scenario has then a specific probability to occur. To use the statistical driver model, every accident scene has to be simulated with each driver scenario (combinations of reaction times and intensities). The results of the simulations are then combined regarding the probabilities to occur, which leads to an overall estimated benefit of the specific system. The model works with one or more equipped participants and delivers a range for the benefit of advanced safety systems with warning interfaces.
The focus of the technical innovation in the automobile industry is currently changing to sensor based safety systems, which are operating in the pre-crash phase of an accident. To get more information about this pre-crash phase for real accidents a simulation of this phase using the GIDAS database is done. The basics for this simulation are geometrical information about the accident location and the exact accident data out of the GIDAS database. This aggregated information gives the possibility to simulate an exact motion for every accident participant, using MATLAB / SIMULINK, in the pre-crash phase. After the simulation the information about the geometrical positions, the velocities and maneuvers of the drivers to an individual TTC (time to collision) are available. With those results it is possible to develop new useful sensor geometries using pre-crash scatter plots or estimate the efficiency of implemented active safety systems in combination with sensor characteristics. This simulation can be done for every reconstructed accident included in the GIDAS database, so these results can represent a wide spread basis for the further development of active safety systems and sensor geometries and characteristics
One main objective of the EU-Project SENIORS is to provide improved methods to assess thoracic injury risk to elderly occupants. In contribution to this task paired simulations with a THOR dummy model and human body model will be used to develop improved thoracic injury risk functions. The simulation results can provide data for injury criteria development in chest loading conditions that are underrepresented in PMHS test data sets that currently proposed risk functions are based on. To support this approach a new simplified generic but representative sled test fixture and CAE model for testing and simulation were developed. The parameter definition and evaluation of this sled test fixture and model is presented in this paper. The justification and definition of requirements for this test set-up was based on experience from earlier studies. Simple test fixtures like the gold standard sled fixture are easy to build and also to model in CAE, but provide too severe belt-only loading. On the other hand a vehicle buck including production components like airbag and seat is more representative, but difficult to model and to be replicated at a different laboratory. Furthermore some components might not be available for physical tests at later stage. The basis of the SENIORS generic sled test set-up is the gold standard fixture with a cable seat back and foot rest. No knee restraint was used. The seat pan design was modified including a seat ramp. The three-point belt system had a generic adjustable load limiter. A pre-inflated driver airbag assembly was developed for the test fixture. Results of THOR test and simulations in different configurations will be presented. The configurations include different deceleration pulses. Further parameter variations are related to the restraint system including belt geometry and load limiter levels. Additionally different settings of the generic airbag were evaluated. The test set-up was evaluated and optimized in tests with the THOR-M dummy in different test configurations. Belt restraint parameters like D-ring position and load limiter setting were modified to provide moderate chest loading to the occupant. This resulted in dummy readings more representative of the loading in a contemporary vehicle than most available PMHS sled tests reported in the literature. However, to achieve a loading configuration that exposes the occupant to even less severe loading comparable to modern vehicle restraints it might be necessary to further modify the test set-up. The new generic sled test set-up and a corresponding CAE model were developed and applied in tests and simulations with THOR. Within the SENIORS project with this test set-up also volunteer and PMHS as well as HBM simulations are performed, which will be reported in other publications. The test environment can contribute in future studies to the assessment of existing and new frontal impact dummies as well as dummy improvements and related instrumentation. The test set-up and model could also serve as a new standard test environment for PMHS and volunteer tests as well as HBM simulations.
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
Accidents involving two wheels vehicles represent one of the more important types of accidents in Europe. These accidents are usually not easy to reconstruct specially for the analysis of the injuries and its correlation with accident dynamics and evidences. Different methodologies are applied in this work for the reconstruction of two wheeler accidents, especially accident involving motorcycles. From the typologies of road evidences like skid marks, to the use of Pc-Crash and the use of Madymo models, different reconstruction of real accidents are presented. One of the questions that sometimes arise for legal purposes when some type of head injuries arise is if the occupant was wearing or not a helmet. The correlation of head injuries with the use of the helmet is a very important issue, therefore an important legal aspect. One of the key questions for the reconstructions that is difficult to analyze, is if the vehicle occupant, was or not, wearing the helmet. Based on the previously collected information, a generic model of a helmet was developed on CAD 3D, followed by its conversion into finite elements, all in order to perform impact tests using the Madymo software that would help improve the helmet- safety, but that also can be used as a tool in accident reconstruction.
Validation of human pedestrian models using laboratory data as well as accident reconstruction
(2007)
Human pedestrian models have been developed and improved continually. This paper shows the latest stage in development and validation of the multibody pedestrian model released with MADYMO. The biofidelity of the multibody pedestrian model has been verified using a range of full pedestrian-vehicle impact tests with a large range in body sizes (16 male, 2 female, standing height 160-192cm, weight 53.5-90kg). The simulation results were objectively correlated to experimental data. Overall, the model predicted the measured response well. In particular the head impact locations were accurately predicted, indicated by global correlation scores over 90%. The correlation score for the bumper forces and accelerations of various body parts was lower (47-64%), which was largely attributed to the limited information available on the vehicle contact characteristics (stiffness, damping, deformation). Also, the effects of the large range in published leg fracture tolerances on the predicted risk to leg fracture by the pedestrian model were evaluated and compared with experimental results. The validated mid-size male model was scaled to a range of body sizes, including children and a female. Typical applications for the pedestrian models are trend studies to evaluate vehicle front ends and accident reconstructions. Results obtained in several studies show that the pedestrian models match pedestrian throw distances and impact locations observed in real accidents. Larger sets of well documented cases can be used to further validate the models especially for specific populations as for instance children. In addition, these cases will be needed to evaluate the injury predictive capability of human models. Ongoing developments include a so-called facet pedestrian model with a more accurate geometry description and a more humanlike spine and neck and a full FE model allowing more detailed injury analysis.
Impact severity is a fundamental measure for all in-depth crash investigation projects. One methodology used in the UK is based on the US Calspan software package CRASH3. The UK- in-depth crash investigation studies routinely use AiDamage3 a software package which is based on an updated version of the original CRASH3 algorithm, including enhancements to the vehicle stiffness coefficients. Real world accident-damaged vehicles are measured and their crush is correlated with a library of stiffness coefficients. These measurements are then used, along with other parameters, to calculate the crash energy and equivalent changes of velocity of the vehicles (delta-v), which is a measure of the impact severity. UK in-depth accident studies routinely validate the crash severity methodologies applied as the vehicle fleet changes. This is achieved by analysing crash test data and using the appropriate residual crush damage and other inputs to AiDamage3 and checking the program- outputs with the known crash severity parameters. This procedure checks, at least in part, the default stiffness values in the data libraries and the reconstruction methods used.
Pedestrian and cyclist are the most vulnerable road users in traffic crashes. One important aspect of this study was the comparable analysis of the exact impact configuration and the resulting injury patterns of pedestrians and cyclists in view of epidemiology. The secondary aim was assessment of head injury risks and kinematics of adult pedestrian and cyclists in primary and secondary impacts and to correlate the injuries related to physical parameters like HIC value, 3ms linear acceleration, and discuss the technical parameter with injuries observed in real-world accidents based documented real accidents of GIDAS and explains the head injuries by simulated load and impact conditions based on PC-Crash and MADYMO. A subsample of n=402 pedestrians and n=940 bicyclists from GIDAS database, Germany was used for preselection, from which 22 pedestrian and 18 cyclist accidents were selected for reconstruction by initially using PC-Crash to calculate impact conditions, such as vehicle impact velocity, vehicle kinematic sequence and throw out distance. The impact conditions then were employed to identify the initial conditions in simulation of MADYMO reconstruction. The results show that cyclists always suffer lower injury outcomes for the same accident severity. Differences in HIC, head relative impact velocity, 3ms linear contiguous acceleration, maximum angular velocity and acceleration, contact force, throwing distance and head contact timing are shown. The differences of landing conditions in secondary impacts of pedestrians and cyclists are also identified. Injury risk curves were generated by logistic regression model for each predicting physical parameters.
The need of passive safety devices, able to reduce the accidents and the severity of injuries suffered by motorcyclist, distinctly arises from data on accident statistics. In this paper, the effectiveness of an airbag device fitted in the biker- garments has been verified through various numerical simulations. Two simple test conditions were defined, in order to investigate the performance of the device both for back and front impacts, and simulated at various impact speeds. With the aim of providing more information about the actual capability of the airbag to reduce the severity of the injuries, one of accident scenario described by ISO 13232:2005 has been also investigated, checking the real effectiveness of the airbag strap-based firing system too. Confrontation of injury indexes resulting from simulation with and without airbag made possible a realistic evaluation of the harm reduction induced by the airbag presence.
Among European Countries, Spain first issued a Standard, UNE 135900:2005, further updated in 2008, that deals with homologation and effectiveness evaluation of road restraint systems components designed to reduce harm for bikers impacting on them. An in depth analysis and critical review of this standard is reported in this paper. Beside a close examination of the standard requirements, numerical models of the crash test stated by the standard have been set up and simulated to study the effects of slight speed and approach angle variations on test results, remaining within tolerance gaps allowed by the standard. Model were validated against experimental data. Together with the expected increasing severity of the impact according with speed, a strong influence of approach angle on injury parameters was found. Possible improvements to the norm, in order to make it more robust, are suggested.