Abteilung Fahrzeugtechnik
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (97)
- Buch (Monographie) (49)
- Wissenschaftlicher Artikel (45)
- Arbeitspapier (13)
- Teil eines Buches (Kapitel) (5)
Sprache
- Englisch (106)
- Deutsch (101)
- Mehrsprachig (2)
Schlagworte
- Safety (77)
- Sicherheit (76)
- Fahrzeug (57)
- Vehicle (57)
- Bewertung (51)
- Deutschland (46)
- Germany (46)
- Anfahrversuch (45)
- Evaluation (assessment) (45)
- Impact test (veh) (42)
Institut
- Abteilung Fahrzeugtechnik (209) (entfernen)
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
The Joint Transport Research Centre of the Organisation for Economic Co-operation and Development and the International Transport Forum recently conducted a benchmarking study of the safety and productivity of typical highway transport trucks from various countries. This paper focuses on vehicle productivity and efficiency in regard to the movement of freight. Forty vehicles from 10 countries were examined. The vehicles were designed for longer-haul applications and were classified in three separate categories: workhorse vehicles, which are the most common and can travel on most roads; high-capacity vehicles, which may be restricted to a certain class of road; and very high-capacity vehicles, which may be restricted to specific highways or routes. The metrics used in the analysis include maximum cargo mass and volume capacity, optimum cargo density, fuel consumption, and carbon dioxide output as a function of the freight task. The study found that size and weight regulations have a significant effect on the productivity and efficiency of heavy vehicles, including fuel consumption and vehicle emissions per unit of cargo transported. Significant variations were found among the vehicles from participating countries as well as within vehicle classes. It was also apparent that, in general, higher-productivity vehicles are correlated more strongly with increased cargo volume than with increased cargo mass and that larger trucks are better suited to lower-density freight than are workhorse vehicles. The study also found that it is important to consider the freight task when evaluating vehicle fuel consumption and emissions.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
A reduction of around 48% of all road fatalities was achieved in Europe in the past years including a reduced number of fatalities with an older age. However, among all road fatalities, the proportion of elderly is steadily increasing. In an ageing society, the European (Horizon2020) project SENIORS aims to improve the safe mobility of older road users, who have different transportation habits compared to other age groups. To increase their level of safe mobility by determining appropriate requirements for vehicle safety systems, the characteristics of current road traffic collisions involving the elderly and the injuries that they sustain need to be understood in detail. Hereby, the paper focuses on their traffic participation as pedestrian, cyclist or passenger car occupant. Following a literature review, several national and international crash databases and hospital statistics have been analysed to determine the body regions most frequently and severely injured, specific injuries sustained and types of crashes involved, always comparing older road users (65 years and more) with mid-aged road users (25-64 years). The most important crash scenarios were highlighted. The data sources included European statistics from CARE, data on national level from Germany, Sweden, Italy, United Kingdom and Spain as well as in-depth crash information from GIDAS (Germany), RAIDS (UK), CIREN and NASS-CDS (US). In addition, familiar hospital data from Germany (TraumaRegister DGU-®), Italy (Italian Register of Acute Traumas) and UK hospital statistics (TARN) were included in the study to gain further insight into specific injury patterns. Comprehensive data analyses were performed showing injury patterns of older road users in crashes. When comparing with mid-aged road users, all databases showed that the thorax body region is of particularly high importance for the older car occupant with injury severities of AIS 2 or AIS 3+, whereas the body regions lower extremities, head and thorax need to be considered for the older pedestrians and cyclists. Besides these comparisons, the most frequent and severe top 5 injuries were highlighted per road user group. Further, the most important crash configurations were identified and injury risk functions are provided per age group and road user group. Although several databases have been analysed, the picture on the road safety situation of older road users in Europe was not complete, as only Western European data was available. The linkage between crash data and hospital data could only be made on a general level as their inclusion criteria were quite different.
Europe has benefited from a decreasing number of road traffic fatalities. However, the proportion of older road users increases steadily. In an ageing society, the SENIORS project aims to improve the safe mobility of older road users by determining appropriate requirements towards passive vehicle safety systems. Therefore, the characteristics of road traffic crashes involving the elderly people need to be understood. This paper focuses on car occupants and pedestrians or cyclists in crashes with modern passenger cars. Ten crash databases and four hospital statistics from Europe have been analysed to answer the questions on which body regions are most frequently and severely injured in the elderly, and specific injuries sustained by always comparing older (65 years and above) with midâ€aged road users (25â€64 years). It was found that the body region thorax is of particularly high importance for the older car occupant with injury severities of AIS2 or AIS3+, where as the lower extremities, head and the thorax need to be considered for older pedestrians and cyclists. Further, injury risk functions were provided. The hospital data analysis showed less difference between the age groups. The linkage between crash and hospital data could only be made on a general level as their inclusion criteria were quite different.
The presence and performance of Advanced Driver Assistance Systems (ADAS) has increased over last years. Systems available on the market address also conflicts with vulnerable road users (VRUs) such as pedestrians and cyclists. Within the European project PROSPECT (Horizon2020, funded by the EC) improved VRU ADAS systems are developed and tested. However, before determining systems" properties and starting testing, an up-to-date analysis of VRU crashes was needed in order to derive the most important Use Cases (detailed crash descriptions) the systems should address. Besides the identified Accident Scenarios (basic crash descriptions), this paper describes in short the method of deriving the Use Cases for car-to-cyclist crashes. Method Crashes involving one passenger car and one cyclist were investigated in several European crash databases looking for all injury severity levels (slight, severe and fatal). These data sources included European statistics from CARE, data on national level from Germany, Sweden and Hungary as well as detailed accident information from these three countries using GIDAS, the Volvo Cars Cyclist Accident database and Hungarian in-depth accident data, respectively. The most frequent accident scenarios were studied and Use Cases were derived considering the key aspects of these crash situations (e.g., view orientation of the cyclist and the car driver- manoeuvre intention) and thus, form an appropriate basis for the development of Test Scenarios. Results Latest information on car-to-cyclist crashes in Europe was compiled including details on the related crash configurations, driving directions, outcome in terms of injury severity, accident location, other environmental aspects and driver responsibilities. The majority of car-to-cyclist crashes occurred during daylight and in clear weather conditions. Car-to-cyclist crashes in which the vehicle was traveling straight and the cyclist is moving in line with the traffic were found to result in the greatest number of fatalities. Considering also slightly and seriously injured cyclists led to a different order of crash patterns according to the three considered European countries. Finally the paper introduced the Use Cases derived from the crash data analysis. A total of 29 Use Cases were derived considering the group of seriously or fatally injured cyclists and 35 Use Cases were derived considering the group of slightly, seriously or fatally injured cyclists. The highest ranked Use Case describes the collision between a car turning to the nearside and a cyclist riding on a bicycle lane against the usual driving direction. A unified European dataset on car-to-cyclist crash scenarios is not available as the data available in CARE is limited, hence national datasets had to be used for the study and further work will be required to extrapolate the results to a European level. Due to the large number of Use Cases, the paper shows only highest ranked ones.
The technology involved in traffic control in Germany has undergone significant changes. This paper describes how a group of German manufacturers have worked with operators to produce Open Communications Interface for Road Traffic Control Systems (OCIT). At the beginning of 2010, twenty-one different European manufacturers had bought licences for OCIT outstations.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
There is considerable evidence for the negative effects of driver distraction on road safety. In many experimental studies, drivers have been primarily viewed as passive receivers of distraction. Thus, there is a lack of research on the mediating role of their self-regulatory behavior. The aim of the current study was to compare drivers' performance when engaged in a system-paced secondary task with a self-paced version of this task and how both differed from baseline driving performance without distraction. Thirty-nine participants drove in a simulator while performing a secondary visual"manual task. One group of drivers had to work on this task in predefined situations under time pressure, whereas the other group was free to decide when to work on the secondary task (self-regulation group). Drivers' performance (e.g., lateral and longitudinal control, brake reaction times) was also compared with a baseline condition without any secondary task. For the system-paced secondary task, distraction was associated with high decrements in driving performance (especially in keeping the lateral position). No effects were found for the number of collisions, probably because of the lower driving speeds while distracted (compensatory behavior). For the self-regulation group, only small impairments in driving performance were found. Drivers engaged less in the secondary task during foreseeable demanding or critical driving situations. Overall, drivers in the self-regulation group were able to anticipate the demands of different traffic situations and to adapt their engagement in the secondary task, so that only small impairments in driving performance occurred. Because in real traffic drivers are mostly free to decide when to engage in secondary tasks, it can be concluded that self-regulation should be considered in driver distraction research to ensure ecological validity.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
Etwa ab Fahrgeschwindigkeiten von 60 km/h wird bei Pkw das Abrollgeräusch der Reifen auf der Straße zur dominierenden Geräuschquelle, Maßnahmen zur Minderung der Geräuschemission von Pkw auf schnell befahrenen Straßen müssen daher primär an den Entstehungsmechanismen dieser Reifen/Fahrbahngeräusche ansetzen. Bisher sind im wesentlichen zwei Hauptursachen für die Geräuscherzeugung gefunden worden: die Schwingungsanregung der Reifendecke und die Bildung aerodynamischer Schallquellen im Reifenprofil. Aus früheren Untersuchungen am Innentrommelprüfstand der Bundesanstalt für Straßenwesen und Messungen an Autobahnfahrbahnen mit Zementdeckschichten ist bekannt, dass Feinsplittabstreuungen die Reifengeräuschemissionen absenken können. Am Prüfstand Fahrzeug/Fahrbahn der BASt wurden Reifengeräusch-, Rollwiderstands-, Griffigkeits- und Texturmessungen an Abstreuungen verschiedener Körnungen durchgeführt. Ziel der Untersuchungen war es dabei, festzustellen, ob durch Splittabstreuungen der Geräuschpegel von Pkw-Reifen abgesenkt werden kann, wie die Reifengeräuschemission von der Texturtiefe der Abstreuung abhängt und wie sich Rollwiderstand, Griffigkeit und Textur abgestreuter Decken mit der Verringerung der Größe des Abstreukorns verändern. Die günstigsten Ergebnisse bei Rollgeräusch und Rollwiderstand wurden im Bereich von Korndurchmessern zwischen 1-2 mm gefunden, zudem weisen die untersuchten Fahrbahndecken in diesem Kornbereich eine gute Griffigkeit auf.
The objective of this deliverable is to describe the expected influence of the candidate test procedures developed in FIMCAR for frontal impact on other impact types. The other impact types of primary interest are front-to-side impacts, collisions with road restraint systems (e.g. guardrails), and heavy goods vehicle impacts. These collision types were chosen as they involve structures that can be adapted to improve safety. Collisions with vulnerable road users (VRU) were not explicitly investigated in FIMCAR. It is expected that the vehicle structures of interest in FIMCAR can be designed into a VRU friendly shell. Information used for this deliverable comes from simulations and car-to-car crash tests conducted in FIMCAR or review of previous research. Three test configurations (full width, offset, and moving deformable barriers) were the input to the FIMCAR selection process. There are three different types of offset tests and two different full width tests. During the project test procedures could be divided into three groups that provide different influences or outcomes on vehicle designs: 1. The ODB barrier provides a method to assess part of the vehicles energy absorption capabilities and compartment test in one test. 2. The FWRB and FWDB have similar capabilities to control structural alignment, further assess energy absorption capabilities, and promote the improvements in the occupant restraint system for high deceleration impacts. 3. The PDB and MPDB can be used to promote better load spreading in the vehicle structures, in addition to assessing energy absorption and occupant compartment strength in an offset configuration. The consortium selected the ODB and FWDB as the two best candidates for short term application in international rulemaking. The review of how all candidates would affect vehicle performance in other impacts (beside front-to-front vehicle or frontal impacts with fixed obstacles) however is reported in this deliverable to support the benefit analysis reported in FIMCAR. The grouping presented above is used to discuss all five test candidates using similarities between certain tests and thereby simplify the discussion.
The objectives of the FIMCAR (Frontal Impact and Compatibility Assessment Research) project are to answer the remaining open questions identified in earlier projects (such as understanding of the advantages and disadvantages of force based metrics and barrier deformation based metrics, confirmation of specific compatibility issues such as structural interaction, investigation of force matching) and to finalise the frontal impact test procedures required to assess compatibility. Research strategies and priorities were based on earlier research programs and the FIMCAR accident data analysis. The identified real world safety issues were used to develop a list of compatibility characteristics which were then prioritised within the consortium. This list was the basis for evaluating the different test candidates. This analysis resulted in the combination of the Full Width Deformable Barrier test (FWDB) with compatibility metrics and the existing Offset Deformable Barrier (ODB) as described in UN-ECE Regulation 94 with additional cabin integrity requirement as being proposed as the FIMCAR assessment approach. The proposed frontal impact assessment approach addresses many of the issues identified by the FIMCAR consortium but not all frontal impact and compatibility issues could be addressed.
Accident analysis
(2014)
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and frontal impact working group (WG15) and the EC funded FP5 VC-COMPAT project activities, two test approaches have been identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in today- research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis should be performed. The specific objectives of the work reported in this deliverable were: - Determine if previously identified compatibility issues are still relevant in current vehicle fleet: Structural interaction, Frontal force matching, Compartment strength in particular for light cars. - Determine nature of injuries and injury mechanisms: Body regions injured o Injury mechanism: Contact with intrusion, Contact, Deceleration / restraint induced. The main data sources for this report were the CCIS and Stats 19 databases from Great Britain and the GIDAS database from Germany. The different sampling and reporting schemes for the detailed databases (CCIS & GIDAS) sometimes do not allow for direct comparisons of the results. However the databases are complementary " CCIS captures more severe collisions highlighting structure and injury issues while GIDAS provides detailed data for a broader range of crash severities. The following results represent the critical points for further development of test procedures in FIMCAR.
Die Beurteilung der technischen und unfallrelevanten Eigenschaften der beiden Scheibenarten zeigt, dass die VSG-Scheibe gegenüber der ESG-Scheibe hinsichtlich der Verletzungs- und Unfallgefahr zwar überwiegend Vorteile aufweist; diese Vorteile sind jedoch vor allem vor dem Hintergrund steigender Gurtanlegequoten nicht als so entscheidend anzusehen, dass daraus die Begründung für ein Verbot der ESG-Scheibe abzuleiten wäre. Diese Feststellung wird insbesondere auch gestützt durch eine Nutzen-Kosten-Betrachtung, die zeigt, dass aus gesamtwirtschaftlicher Sicht bei einem generellen Ersatz der ESG-Scheibe durch die teurere VSG-Scheibe bei günstigen Annahmen der Nutzen unter den Kosten liegen würde.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
The term test procedure refers to a method that describes how a system has to be tested to identify and assess specific behavior or properties by experiments. This also includes the specification of required tools, equipment, boundary conditions, and evaluation methods. Test procedures are an essential tool to check whether desired product properties are present, which of course also applies to the development of driver assistance systems. In addition to development and release testing that mainly is performed by the vehicle or system manufacturer, there are tests with the purpose of an independent product testing that are conducted by external test organizations. These tests are needed for vehicle type approval (for admission to a specific market), in the context of applying the standard for functional safety (in both cases mainly executed by technical services (being accredited as certification laboratory)) or for customer information purposes (by a test institute for consumer protection). The focus of this chapter is these "external" test methods. After a taxonomy of test procedures, the differences between legislation (type approval) and consumer testing are highlighted. Typical tests and the associated test setup, tools, and assessment criteria are discussed, and an outlook toward testing in the near and mid-future is given.
Schutz von schwächeren Verkehrsteilnehmern: kommende Anforderungen aus Gesetzgebung und Euro NCAP
(2017)
Systeme der aktiven Fahrzeugsicherheit, insbesondere Notbremsassistenzsysteme und automatische Notbremssysteme, haben in den letzten zwei Dekaden große technische Fortschritte gemacht, und das im Wesentlichen ohne "Druck" von Gesetzgeber oder unabhängigen Testorganisationen " diese können aber durch passende Anforderungen den Vormarsch der Systeme in die Breite und die Ausnutzung von ansonsten für den Hersteller vielleicht nicht wirtschaftlichen Potentialen unterstützen. Dieser Bericht hat das Ziel, einen Überblick über die kommenden Anforderungen an Schutzsysteme für schwächere Verkehrsteilnehmer zu geben und diese Anforderungen in den Kontext Euro NCAP (=welchen Einfluss haben diese Anforderungen auf die Gesamtbewertung?) sowie Gesetzgebung (schwächere Anforderungen, aber dafür ein Markteintrittskriterium) zu stellen: - Anforderungen und Testprozeduren für Notbremsassistenz Fahrradunfälle 2018 und 2020 in Euro NCAP; - Anforderungen und Testprozeduren für Notbremsassistenz bei Nachtunfällen mit Fußgängern in Euro NCAP 2018; - Anforderungen und Testprozeduren für Abbiegeassistenzsysteme zum Schutz von Radfahrern in Unfallsituationen mit rechtsabbiegenden Lkw innerhalb der Fahrzeugtypgenehmigung.
PROSPECT (Proactive Safety for Pedestrians and Cyclists) is a collaborative research project involving most of the relevant partners from the automotive industry (including important active safety vehicle manufacturers and tier-1 suppliers) as well as academia and independent test labs, funded by the European Commission in the Horizon 2020 research program. PROSPECT's primary goal is the development of novel active safety functions, to be finally demonstrated to the public in three prototype vehicles. A sound benefit assessment of the prototype vehicle's functionality requires a broad testing methodology which goes beyond what has currently been used. Since PROSPECT functions are developed to prevent accidents in intersections, a key aspect of the test methodology is the reproduction of natural driving styles on the test track with driving robots. For this task, data from a real driving study with subjects in a suburb of Munich, Germany was used. Further data from Barcelona will be available soon. The data suggests that intersection crossing can be broken down into five phases, two phases with straight deceleration / acceleration, one phase with constant radius and speed turning, and two phases where the bend is imitated or ended. In these latter phases, drivers mostly combine lateral and longitudinal accelerations and drive what is called a clothoid, a curve with curvature proportional to distance travelled, in order to change lateral acceleration smoothly rather than abrupt. The data suggests that the main parameter of the clothoid, the ratio distance travelled to curvature, is mostly constant during the intersections. This parameter together with decelerations and speeds allows the generation of synthetic robot program files for a reproduction of natural driving styles using robots, allowing a much greater reproducibility than what is possible with human test drivers. First tests show that in principle it is possible to use the driving robots for vehicle control in that manner; a challenge currently is the control performance of the robot system in terms of speed control, but it is anticipated that this problem will be solved soon. Further elements of the PROSPECT test methodology are a standard intersection marking to be implemented on the test track which allows the efficient testing of all PROSPECT test cases, standard mobile and light obstruction elements for quick reproduction of obstructions of view, and a concept for tests in realistic surroundings. First tests using the PROSPECT test methodology will be conducted over the summer 2017, and final tests of the prototype vehicles developed within PROSPECT will be conducted in early 2018
Accidents between right turning trucks and straight driving cyclists often show massive consequences. Accident severity in terms of seriously or fatally injured cyclists that are involved is much higher than in accidents of other traffic participants in other situations. It seems clear that adding additional mirrors will very likely not improve the situation. At ESV 2015, a methodology to derive test procedures and first test cases as well as requirements for a driver assist system to address blind spot accidents has been presented. However, it was unclear if and how testing of these cases is feasible, to what extent characteristics of different truck concepts (e.g. articulated vehicles, rigid vehicles) influence the test conduction and outcome, and what tolerances should be selected for the different variables. This work is important for the acceptance of a draft regulation in the UN working group on general safety. In the meantime, three test series using a single tractor vehicle, a tractor-semitrailer combination and a rigid vehicle have been conducted. The test tools (e.g. surrogate devices) have been refined. A fully crashable, commercially available bicycle dummy has been tested. If used correct, this dummy does follow a straight line quite precisely and it does not cause any damage to the truck under test in case of accidental impact. The dummy specifications are freely available. During testing, the different vehicle categories resulted in different trajectories being driven. Articulated vehicle combinations did first execute a turn into the opposite direction, and on the other hand, single tractor vehicles did behave comparable to passenger cars. A possible solution to take these behaviors into account is to require the vehicles to drive through a corridor that is narrow for a precise straight-driving phase and extends during the turn. Other investigated parameters are the dummy and vehicle speed tolerances. The results from this research make it possible to draft a regulation for a driver assistance system that helps to avoid blind spot accidents: test cases have been refined, their feasibility has been checked, and corridors for the vehicles and for important parameters (e.g. test speeds) have been set. The test procedure is applicable to all types of heavy goods vehicles. In combination with the accidentology (ESV 2015 paper), the work provides the basis for a regulation for such an assistance system.
It is commonly agreed that active safety will have a significant impact on reducing accident figures for pedestrians and probably also bicyclists. However, chances and limitations for active safety systems have only been derived based on accident data and the current state of the art, based on proprietary simulation models. The objective of this article is to investigate these chances and limitations by developing an open simulation model. This article introduces a simulation model, incorporating accident kinematics, driving dynamics, driver reaction times, pedestrian dynamics, performance parameters of different autonomous emergency braking (AEB) generations, as well as legal and logical limitations. The level of detail for available pedestrian accident data is limited. Relevant variables, especially timing of the pedestrian appearance and the pedestrian's moving speed, are estimated using assumptions. The model in this article uses the fact that a pedestrian and a vehicle in an accident must have been in the same spot at the same time and defines the impact position as a relevant accident parameter, which is usually available from accident data. The calculations done within the model identify the possible timing available for braking by an AEB system as well as the possible speed reduction for different accident scenarios as well as for different system configurations. The simulation model identifies the lateral impact position of the pedestrian as a significant parameter for system performance, and the system layout is designed to brake when the accident becomes unavoidable by the vehicle driver. Scenarios with a pedestrian running from behind an obstruction are the most demanding scenarios and will very likely never be avoidable for all vehicle speeds due to physical limits. Scenarios with an unobstructed person walking will very likely be treatable for a wide speed range for next generation AEB systems.
The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
Zum gegenwärtigen Zeitpunkt werden verschiedene Ansätze diskutiert, wie der Verbesserung der Straßenverkehrssicherheit durch den Einsatz moderner Fahrerassistenzsysteme (FAS) neue Impulse gegeben werden können. Unter dem Dach der von der Europäischen Kommission gemeinsam mit der Industrie im Frühjahr 2002 ins Leben gerufenen eSafety-Initiative soll die Entwicklung und Implementierung "Intelligenter Integrierter Sicherheitssysteme" (Intelligent Integrated Road Safety Systems) koordiniert und vorangetrieben werden. Erwartet werden hiervon entscheidende Beiträge zur Erreichung der bis zum Jahr 2010 angestrebten Halbierung der Zahl der Verkehrstoten in Europa, entsprechend dem Weissbuch der Europäischen Kommission. Intelligente Unterstützung des Fahrers meint in diesem Zusammenhang die Berücksichtigung des Gesamtsystems "Fahrer-Fahrzeug-Umwelt". Für die fahrzeugseitige Umsetzung der Unterstützungsfunktion wurden verschiedene Ausformungsgrade (zum Beispiel Information, Warnung, korrigierender Eingriff) vorgeschlagen und entwickelt. Die BASt ist an einer Reihe von Projekten und Arbeitsgruppen beteiligt, die sich direkt oder indirekt mit Fragen befassen, die sich bei der Entwicklung und Bewertung intelligenter FAS zur Beeinflussung der Fahrzeuggeschwindigkeit stellen. Im Mittelpunkt stehen dabei vor allem Fragen der Sicherheitsbewertung und der Machbarkeit, wie zum Beispiel - Realisierung der fahrzeugseitigen Umsetzung, - Kosten-Nutzen-Gesichtspunkte, - Rechtliche Aspekte, - Voraussetzungen der Datenbasis. Beispielsweise ist die BASt an der von ERTICO koordinierten "SpeedAlert"-Initiative beteiligt. Ziel dieser Aktivität ist die europaweite Implementierung eines Geschwindigkeitswarnsystems. An der hierzu im Jahre 2001 gegründeten "SpeedAlert" Arbeitsgruppe beteiligen sich Industrie und Verwaltung.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben. Das Ergebnis kann indes nicht zufriedenstellen. Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird im Beitrag, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der sich auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschrieben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen; dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschreiben. Das Ergebnis kann indes nicht zufriedenstellen: Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird hier, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschreiben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen. Dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
Neue Herausforderungen an die Unfallforschung durch Fahrerassistenz und automatisiertes Fahren
(2019)
Unfallrekonstruktion hat die Ableitung von Maßnahmen zur Minimierung der Unfallfolgen ermöglicht, vor allem durch Verbesserungen bei passiven Sicherheitseinrichtungen, aber auch durch die Verbesserung der Rettungskette, beispielsweise eCall. Heute können aktive Sicherheitssysteme die Unfallfolgen bereits vor der eigentlichen Kollision reduzieren oder durch Umfeldwahrnehmung und mittels Eingriff in die Fahrzeugsteuerung gegebenenfalls sogar vollständig verhindern. Funktionen, die aktiv in die Fahrzeugsteuerung eingreifen, lassen sich nach ihrer Wirkweise unterscheiden: zum einen handelt es sich um kontinuierlich automatisierende Funktionen, die meist länger aktiv bleiben (zum Beispiel ACC). Zum anderen um Funktionen, die in kritischen Fahrsituationen temporär in die Fahrzeugsteuerung eingreifen. Aufgezeigt wird, welche Konsequenzen und Risiken in Bezug auf diese Systeme sowie für bestimmte (zum Beispiel kritikale) Fahrsituationen anzunehmen sind. Zur Bewertung von aktiven Reglern, die in kritischen Fahrsituationen eingreifen, sind Unfalldaten nur noch eingeschränkt tauglich. Ähnliches gilt für die Bewertung von Ereignissen/ Zuständen im Rahmen kontinuierlicher Fahrzeugsteuerung, vor allem, wenn diese weiter vorausliegen. Wirkzusammenhänge automatisierter Fahrfunktionen müssen jedoch - gerade für den Mischverkehr mit konventionell gesteuerten Fahrzeugen - identifiziert werden. Dafür wird eine Szenariendatenbank mit relevanten Verkehrssituationen benötigt, in die Daten aus Naturalistic Driving Studies (NDS), aus Fahrversuchen oder Versuchen im Fahrsimulator eingehen können. Die zunehmende Durchdringung der Fahrzeugflotte mit kontinuierlich automatisierten Fahrfunktionen lässt eine Abnahme kritischer Fahrsituationen und eine Reduktion der Zahl der Verkehrsopfer erwarten. Allerdings verbleibt eine Restzahl an systemimmanenten Unfällen, die als unvermeidbar gelten müssen.
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.
Seit 1997 gibt es in Europa unter dem Namen Euro NCAP (European New Car Assessment Programme) einheitliche Test- und Ratingverfahren. Sie liefern Informationen über den Insassen- und über den Fußgängerschutz. Euro NCAP hat seither fast 90 Fahrzeugmodelle in jeweils drei unterschiedlichen Crashtest-Konfigurationen untersucht und die Ergebnisse den europäischen Konsumenten zugänglich gemacht. Im Beitrag wird auf die Testbedingungen, die Euro NCAP-Ratingverfahren sowie auf die Weiterentwicklung von Euro NCAP eingegangen. Ein wichtiger Aspekt wird dabei auch die weltweite Harmonisierung der Test- und Ratingverfahren sein.
Der Vorschlag, dass alle Kraftfahrzeuge auch am Tag mit Licht fahren sollen, wird seit vielen Jahren national und international diskutiert. Aufgrund dessen hat das Bundesministerium für Verkehr, Bau- und Wohnungswesen die Bundesanstalt für Straßenwesen beauftragt, die Auswirkungen des Fahrens mit Licht am Tag auf die Straßenverkehrssicherheit in Deutschland im Rahmen eines Forschungsprojektes genauer zu untersuchen. Auf der Basis einer Bewertung der internationalen Literatur zur Wirksamkeit des Fahrens mit Licht am Tag kommt die BASt zu dem Ergebnis, dass bei obligatorischer Einführung dieser Verkehrssicherheitsmaßnahme in der Bundesrepublik Deutschland eine deutliche Verbesserung der Verkehrssicherheit erwartet werden kann. Die Unfallrückgänge liegen in einer Größenordnung von über 3%. Die Befürchtung, dass sich demgegenüber Nachteile für schwächere Verkehrsteilnehmer, insbesondere Motorradfahrer, ergeben und deren Unfallhäufigkeit steigt, konnte nicht erhärtet werden. Die obligatorische Einführung des Fahrens mit Licht am Tag ist unter gesamtwirtschaftlichen Gesichtspunkten auch effizient. Den zu erwartenden Sicherheitsnutzen in Höhe von umgerechnet 1 Mrd. € je Jahr stehen Kosten in Folge des zunehmenden Kraftstoffverbrauchs und der damit verbundenen Emissionen in Höhe von 630 Mio. € (ungünstigster Fall: Fahren mit Abblendlicht) gegenüber. Auf lange Sicht sinken mit speziellen Tagfahrleuchten diese Kosten auf 150 Mio. € (Tagfahrleuchten in Glühlampentechnik) oder sogar nur 60 Millionen Euro (Tagfahrleuchten in LED-Technik). Es wird deshalb empfohlen, - für Neufahrzeuge eine Ausrüstung mit Tagfahrleuchten mit automatischer Aktivierung, gekoppelt an die Zündung, vorzuschreiben, - sowie einen Dämmerungsschalter zur automatischen Einschaltung des Abblendlichts obligatorisch einzuführen. Um einen nachteiligen Sicherheitseffekt durch die Durchmischung mit beleuchteten und unbeleuchteten Fahrzeugen zu vermeiden, ist für Altfahrzeuge ohne spezielle Tagfahrleuchten das Fahren mit Licht am Tag ganzjährig auf dem gesamten Straßennetz dringend zu empfehlen. Die Empfehlung für den bestehenden Kraftfahrzeugbestand sollte spätestens zum Zeitpunkt der Einführung der Ausstattungsvorschrift für die Neufahrzeuge ausgesprochen werden.
Motorcycling is a fascinating kind of transportation. While the riders' direct exposure to the environment and the unique driving dynamics are essential to this fascination, they both cause a risk potential which is several times higher than when driving a car. This chapter gives a detailed introduction to the fundamentals of motorcycle dynamics and shows how its peculiarities and limitations place high demands on the layout of dynamics control systems, especially when cornering. The basic principles of dynamic stabilization and directional control are addressed along with four characteristic modes of instability (capsize, wobble, weave, and kickback). Special attention is given to the challenges of braking (brake force distribution, dynamic over-braking, kinematic instability, and brake steer torque induced righting behavior). It is explained how these challenges are addressed by state-of-the-art brake, traction, and suspension control systems in terms of system layout and principles of function. It is illustrated how the integration of additional sensors " essentially roll angle assessment " enhances the cornering performance in all three categories, fostering a trend to higher system integration levels. An outlook on potential future control systems shows exemplarily how the undesired righting behavior when braking in curves can be controlled, e.g., by means of a so-called brake steer torque avoidance mechanism (BSTAM), forming the basis for predictive brake assist (PBA) or even autonomous emergency braking (AEB). Finally, the very limited potential of brake and chassis control to stabilize yaw and roll motion during unbraked cornering accidents is regarded, closing with a promising glance at roll stabilization through a pair of gimbaled gyroscopes.
Abbiegeunfälle mit Kollisionen zwischen rechtsabbiegenden Güterkraftfahrzeugen und Fahrrädern haben in der Regel schwerwiegende Folgen für den ungeschützten Verkehrsteilnehmer. In der Vergangenheit wurde durch eine steigende Anzahl von Spiegeln das individuelle Sichtfeld des Lkw-Fahrers vergrößert und die Sicherheit für ungeschützte Verkehrsteilnehmer durch den Seitenunterfahrschutz verbessert. Da Abbiegeunfälle trotz der Vielzahl an Spiegeln auch heute noch geschehen, gleichzeitig aber Fahrerassistenzsysteme Einzug in viele Fahrzeugklassen gehalten haben, liegt es nahe, derartige Systeme für die Verhinderung von Abbiegeunfällen zu nutzen. Um entsprechende Systementwicklungen fördern zu können oder aber auch Systeme vorschreiben zu können, sind Anforderungen und passende Testmethoden für Abbiegeassistenzsysteme erforderlich. Ziel der BASt war es, solche Anforderungen und ein mögliches Testverfahren hierfür zu entwickeln. Ausgehend von Analysen des Unfallgeschehens wurden charakteristische Parameter und Begleitumstände von Unfällen zwischen Fahrrädern und rechtsabbiegenden Lkw identifiziert. Aus fahrdynamischen Überlegungen folgt bei den gegebenen Parametern, dass nur eine frühe, aber niederschwellige Fahrerinformation eine wirkungsvolle Assistenzfunktion zur Verhinderung der Unfälle sein kann. Für automatische Bremsungen gibt es bisher noch zu wenig Erfahrungen im Feld, und klassische, hochschwellige, aber sehr spät erfolgende Warnsignale würden durch die dann noch verstreichende Reaktionszeit keine rechtzeitige Bremsung des Lkw-Fahrers mehr hervorrufen. Basierend auf dem identifizierten Parameterraum, der zum komfortablen Anhalten erforderlichen Zeit und einem geeigneten Kinematikmodell lassen sich die räumlichen Bereiche um den Lkw definieren, in dem eine Umfelderkennung den Fahrradfahrer detektieren können muss, damit das Informationssignal durch das Assistenzsystem an den Lkw-Fahrer rechtzeitig ausgegeben wird. Aktuell wird davon ausgegangen, dass ein Abbiegeassistenzsystem, das die hier beschriebenen Prüfungen besteht, einen sehr positiven Einfluss auf das Unfallgeschehen zwischen rechtsabbiegenden Lkw und Fahrrädern haben wird.
Economic constraints nowadays require transporting greater volumes of freight at lower cost. Yet, physical profiles of trucks do not all generate the same effects on road infrastructure for a given tonnage hauled. The objective then lies in finding an optimal service level that reduces the damage caused to infrastructure. Results derived for the impact of trucks on pavements are presented. The impact of truck traffic trends on road bridges will also be discussed.rn
Kamera-Monitor-Systeme (KMS) können bei Kraftfahrzeugen dazu verwendet werden, die Sicht nach hinten für den Fahrer auf einem im Fahrzeug montierten Monitor darzustellen. Dies bietet auch die Möglichkeit, herkömmliche Außenspiegel durch geeignete KMS zu ersetzen und damit neue Designvarianten mit aerodynamischen Vorteilen umsetzen zu können. Da es sich bei den Außenspiegeln jedoch um ein sicherheitsrelevantes Fahrzeugteil zur Gewährleistung der indirekten Sicht nach hinten handelt (Anforderungen sind in der UN-Regelung Nr. 46 festgelegt), stellt sich die Frage, ob KMS einen gleichwertigen Ersatz für Spiegel bieten können. In der vorliegenden Studie wurden das KMS und der herkömmliche Außenspiegel während der Durchführung von Versuchsfahrten und statischen Tests unter verschiedenen äußeren Bedingungen verglichen und bewertet. Untersuchungsgegenstand waren zum einen technische Aspekte, zum anderen Fragestellungen zur Gestaltung der Mensch-Maschine-Interaktion. Für die Versuche mit Pkw standen zwei Fahrzeuge zur Verfügung: Ein Fahrzeug, das in Kleinserie hergestellt wird und bereits nur mit KMS als Ersatz für Außenspiegel ausgerüstet ist, sowie ein Fahrzeug der Kompaktklasse, an dem sowohl ein KMS als Nachrüstsatz verbaut war als auch die herkömmlich vorhandenen Außenspiegel. Letztere konnten für Fahrten ausschließlich mit KMS abgedeckt werden. Für die Versuche am Lkw stand eine Sattelzugmaschine mit Auflieger zur Verfügung. Die Fahrerkabine war mit einem nachgerüsteten KMS ausgestattet. Grundsätzlich hat sich gezeigt, dass es möglich ist, die indirekte Sicht nach hinten sowohl bei Pkw als auch bei Lkw durch KMS, die gewisse Qualitätskriterien erfüllen, für den Fahrer ausreichend darstellen zu können. Je nach Ausgestaltung bietet ein KMS sogar die Möglichkeit, mehr Information über den rückwärtigen Raum zu präsentieren als es mit Spiegelsystemen möglich ist. Es hat sich auch gezeigt, dass der Umstieg von Spiegeln auf KMS immer einer gewissen Gewöhnungsphase bedarf, diese jedoch verhältnismäßig kurz ist und nicht notwendigerweise zu sicherheitskritischen Situationen führt.
Camera-monitor systems (CMS) can be used in motor vehicles to display the driver's rear view on a monitor mounted inside the vehicle. This also offers the possibility of replacing conventional exterior mirrors with suitable CMS and thereby implementing new design concepts with aerodynamic advantages. However, as exterior mirrors are safety-relevant vehicle parts for securing the driver's indirect rear view (requirements specified in UN Regulation No. 46), the question arises whether CMS can provide an equivalent substitute for mirrors. In the scope of this study, CMS and conventional exterior mirrors were compared and assessed in test drives and static tests under different external conditions. On the one hand, the examination of technical aspects, and on the other hand, issues pertaining to the design of the human-machine interaction, were the objects of the study. Two vehicles were available for the trials with passenger vehicles: A vehicle, manufactured in small series, which is already equipped with CMS as sole replacement for the exterior mirrors, as well as a compact class vehicle which had a CMS retrofitted by the car manufacturer in addition to conventionally used exterior mirrors. The latter could be covered exclusively for trips with CMS. A tractor unit with semitrailer was available for the truck trials. The driver's cabin was equipped with a CMS system developed by the vehicle manufacturer. In general, it was shown that it is possible to display the indirect rear view sufficiently for the driver, both for cars and trucks, using CMS which meet specific quality criteria. Depending on the design, it is even possible to receive more information about the rear space from a CMS than is possible with mirror systems. It was also shown that the change from mirrors to CMS requires a certain period of familiarisation. However, this period is relatively short and does not necessarily result in safety-critical situations.
Within the automotive context camera monitor systems (CMS) can be used to present views of the traffic situation behind the vehicle to the driver via a monitor mounted inside the cabin. This offers the opportunity to replace classical outside rearview mirrors and therefore to implement new design concepts, aerodynamically optimized vehicle shapes and to reduce the width of the vehicle. Further, the use of a CMS offers the potential to implement functionalities like warnings or situation-adaptive fields of view that are not feasible with conventional rearview mirrors. Despite these potential advantages, it is important to consider the possible technical constraints of this technology and its effect on driver perception and behavior. On the technical side next to the field of view and die robustness of die system, aspects as its functionality at day and night as well as under varying weather conditions should be object to scientific investigation. Concerning human machine interaction, it has to be considered, that the perception of velocities and distances of approaching vehicles might be different for CMS as compared to conventional rearview mirrors and potential influences of factors as the Position of the displays or drivers' age should be taken into account. In order to shed light on these and further open issues, BASt is currently conducting a study that will cover the use of CMS under controlled conditions as well in real traffic. The first part of the study will focus on passenger cars, while in a second step the empirical investigation will be extended to heavy goods vehicles, where the potentials as well as the limitations of CMS might differ considerably. The presentation will cover the first part, with regard to the experimental design, implementation and initial results if already available.
Fahrzeuge, die mit alternativen Antrieben ausgestattet sind, machen 2013 lediglich etwa 2 Prozent des Pkw-Gesamtbestandes aus. Um jedoch die zukünftige Entwicklung von Fahrzeugen mit alternativem Antrieb in Deutschland analysieren und mögliche negative Auswirkungen auf die Verkehrssicherheit identifizieren zu können, ist eine langfristige Beobachtung des Fahrzeugmarktes und des Unfallgeschehens notwendig. Der vorliegende Bericht zeigt in den Kapiteln 2 und 3 die technischen Entwicklungen von Fahrzeugen mit alternativem Antrieb auf und gibt einen Überblick über die Rahmenbedingungen des deutschen Marktes bis 2015. In den Kapiteln 4 und 5 werden der Bestand sowie das Unfallgeschehen näher betrachtet. Der Bericht liefert in diesem statistischen Teil Daten für das Berichtsjahr 2013.
Zu Beginn des Jahres 2016 macht der Anteil der Pkws mit alternativem Antrieb rund 2% des Pkw-Gesamtbestandes aus. Der Bestand an Pkw mit alternativem Antrieb stieg auf rund 712.000 Fahrzeuge im Jahr 2016 (ein Plus von etwa 11% gegenüber 2013). Um die zukünftige Entwicklung von Fahrzeugen mit alternativem Antrieb in Deutschland beurteilen zu können, initiierte die Bundesanstalt für Straßenwesen (BASt) im Auftrag des Bundesministeriums für Verkehr und digitale Infrastruktur (BMVI) schon im Jahr 2010 die Einrichtung einer langfristigen Beobachtung des Fahrzeugmarktes und des Unfallgeschehens von Fahrzeugen mit alternativen Antriebsarten mit dem Ziel, die tatsächliche Umsetzung des technologischen Fortschritts in marktgängige Produkte zu verfolgen, frühzeitig Kenntnis über die Bestandsentwicklung zu erhalten sowie mögliche Fehlentwicklungen " insbesondere mit Blick auf die Verkehrssicherheit " zu identifizieren. Vor allem die Betrachtung des letzten Punktes soll die Möglichkeit schaffen, Vorschläge für eine sinnvolle Steuerung der Entwicklung leisten zu können. Nachfolgend werden in Kapitel 2 die technischen Entwicklungslinien des Marktes für Fahrzeuge mit alternativem Antrieb dargestellt. In den Kapiteln 3 und 4 werden der Bestand sowie das Unfallgeschehen näher betrachtet.
This paper presents findings of a laboratory experiment which aimed at evaluating the sensitivity and intrusiveness of Tactile Detection Response Task (TDRT) methodology. Various single-task, dual-task and triple-task scenarios were compared. The task scenarios included a surrogate of driving (tracking task) and different secondary tasks (N-back, surrogate reference task (SuRT)). The results suggest that the TDRT is sensitive to load levels of secondary tasks which primarily demand for cognitive resources (N-back). Sensitivity to variations of visual"manual load could not be shown (SuRT). TDRT seems also to be able to differentiate between modes of primary task which varies in terms of cognitive load (visual against auditory tracking task). Results indicated intrusiveness of TDRT on primary task performance and secondary task performance depending on the type of underlying task scenario. As a conclusion, TDRT can be recommended as a method to assess attentional effects of cognitive load of a secondary task, but should be used with caution for secondary tasks with strong motor demands.
Die Gestaltung der Interaktion zwischen den elektronischen "Infotainment"-Systemen im Auto und dem Fahrer gewinnt zunehmend an Bedeutung für die Verkehrssicherheit. Dem positiven Nutzen, den die Systeme hinsichtlich Fahrerunterstützung und Fahrkomfort aufweisen, stehen möglicherweise negative Auswirkungen auf die Fahrsicherheit gegenüber, wenn Ablenkung und Überlastung des Fahrers auftreten. Diesem Problemfeld widmete sich das EU-Projekt "Communication Multimedia Unit Inside Car" (COMMUNICAR), das im Juni 2003 abgeschlossen wurde. Hauptziel des Projekts waren die Entwicklung und Evaluierung eines Systems, das den Fahrer bei der Bewältigung der eingehenden Informationen unterstützt und eine zentrale Bedienmöglichkeit aufweist. Das COMMUNICAR-System enthält folgende wesentliche Elemente: Verschiedene Funktionen zu Telematikdiensten, Unterhaltung und zur digitalen Darstellung der traditionellen Informationen; eine als Informationsmanager (IM) bezeichnete regelbasierte Filterlogik sowie eine multimediale integrierte Mensch-Maschine-Schnittstelle (MMS) zur zentralen Bedienung und Informationsausgabe. In der ersten Phase der Entwicklung wurden die Nutzeranforderungen analysiert, die Funktionen definiert und die Ein-/Ausgabemodalitäten festgelegt. In der zweiten Phase wurden virtuelle Prototypen zur Gestaltung der MMS erarbeitet und diese in den anschließenden Nutzertest im Labor bewertet und ausgewählt. Die dritte Phase diente der Systementwicklung, bei der es vor allem um die Filterlogik des IM ging. Das System wurde zunächst im Fahrsimulator, anschließend unter Feldbedingungen getestet. Die Ergebnisse, die in den wesentlichen Einzelheiten berichtet werden, zeigten insgesamt ein positives Bild sowohl hinsichtlich der subjektiven Akzeptanzbewertung als auch hinsichtlich des Fahrverhaltens.
This paper describes the methodology for the assessment of the socio-economic impact of SAFESPOT applications. The applications selected for the assessment cover vehicle to vehicle (v2v) as well as vehicle to infrastructure (v2i) communication systems. The applications address main problem areas of road safety: accidents at intersections, accidents due to hazardous road and weather conditions and accidents due to over speeding and inappropriate distance. The assessment methodology relies in its core on cost-benefit analysis (CBA) as the most widespread tool to assess the profitability of applications form the society point of view. The assessment is however not limited to CBA but also considers the economic effects for particular stakeholder groups such as users, public authorities and the like. Their individual cost and benefits can be investigated in stakeholder analyses. Both elements, CBA and stakeholder analysis, form an integrated assessment approach which is applied here. The assessment makes use of the sound methodological base which was provided by projects such as SEiSS and eIMPACT. Some characteristics of co-operative systems however call for special attention within the assessment. Most prominently, the assessment will concentrate on a bundle of applications. The impact of this bundle will be assessed under the conditions of different business and service models. These issues will be addressed in the paper. Moreover, this paper also provides insight in likely patterns of results and first results of socio-economic impact assessment itself.
This report presents the results of a stakeholder analysis which has been performed by the EasyWay Cooperative Systems Task Force. The stakeholder analysis aims at identifying potential roles of the road operator in the operation process of selected cooperative services and describing expectations and aspirations related to the future roles and responsibilities from a European road operator- point of view. The following cooperative services have been considered in the stakeholder analysis: Hazardous location notification, Traffic jam ahead warning, Road works warning, Automatic access control and Parking management. The stakeholder analysis used findings from previous projects and performed own studies based on desk research and expert assessments which were carried out by the task partners. The approach includes the development of high-level descriptions showing functional schemes of the operational process chains and potential roles / responsibilities related to the road operator. A deepened analysis was performed by assessing the functional schemes / role profiles and collecting opportunities, concerns, and success factors from a road operator- perspective.
Die Griffigkeit ist die maßgebende Größe für die Übertragung der Längs- als auch der Seitenkräfte von Reifen auf die Straßenoberfläche und hat somit einen erheblichen Anteil an der Straßensicherheit. In Deutschland erfolgt die Erfassung der Straßengriffigkeit im Rahmen von Bauverträgen sowie der Zustandserfassung und -bewertung (ZEB) mit dem Seitenkraftmessverfahren (SKM). Mit der Veröffentlichung der TP Griff-StB (SKM) durch die FGSV am 29.4.2008 ist derzeit das aktuellste Dokument für Griffigkeitsmessungen im Rahmen von Bauverträgen sowie der Zustandserfassung und -bewertung von Bundesfernstraßen (ZEB) mit dem Seitenkraftmessverfahren herausgegeben worden. Dieses Dokument löst die TP Griff-StB (SCRIM) mit ihren drei Allgemeinen Rundschreiben ab und fasst die Ergebnisse aus verschiedenen Forschungsprojekten und Erfahrungen aus den regelmäßigen Messungen der Messgerätebetreiber zusammen.
Die Initiative der Einführung kooperativer Systeme in einem Korridor von Rotterdam über Frankfurt/Main nach Wien, dem sogenannten C-ITS Corridor, und damit auch in Deutschland wurde im Juni 2013 durch die Unterzeichnung einer entsprechenden Absichtserklärung des Bundesministeriums für Verkehr, Bau und Stadtentwicklung mit den Verkehrsministern der Niederlande und Österreichs offiziell gestartet. In vielen Forschungsprojekten wurden vorher die Grundlagen erarbeitet, um eine solche Einführung technisch überhaupt erst möglich zu machen. Im Beitrag werden diese Ergebnisse nochmals kurz aufgegriffen und um den aktuellen Stand bei den Entwicklungen im C-ITS Corridor erweitert. Als erstes Einführungsszenario wurden die Baustellenwarnung und Kooperatives Verkehrsmanagement unter Einbeziehung von Fahrzeugdaten gewählt. Nicht verschwiegen werden sollen hierbei auch die wesentlichen Herausforderungen, die im Übergang von Forschung und Feldtests zu realen Anwendungen liegen.
Dem Benzinverbrauch heutiger moderner Kraftfahrzeuge wird in zunehmendem Maße Beachtung geschenkt, um dem Konflikt zwischen Mobilität einerseits und Umweltschutz andererseits entgegenzuwirken. Ein Beitrag hierzu wird in der Reduzierung des Rollwiderstands der Bereifung mit einem Potential von bis zu 5 Prozent gesehen. Insbesondere bei Geschwindigkeiten unterhalb von 80 km/h dominierte der Roll- gegenüber dem Luftwiderstand. Bei der Bundesanstalt für Straßenwesen wurden Systeme und Verfahren für Messungen des Rollwiderstandes von Pkw-Reifen in einem Innentrommelprüfstand sowie mit einem Messanhänger entwickelt. In der vorliegenden Untersuchung wird gezielt der Frage nachgegangen, inwieweit Ergebnisse einer Messung im Prüfstand auf Ergebnisse einer Straßenmessung übertragen werden können und umgekehrt. Der Vergleich zeigt, dass die Messgenauigkeit mit dem Anhänger auf der Straße im Mittel geringer anzusetzen ist und erwartungsgemäß nicht die Aussagequalität von Messungen im Prüfstandsversuch erreicht wird. Dennoch weist jedes System Vorteile auf. So steht mit der Rollwiderstandsmessung im Prüfstand ein Verfahren zur Verfügung, bei dem als Schwerpunkt mehr der reifenseitige als der fahrbahnseitige Aspekt des Rollwiderstandes im Vordergrund steht. Hingegen kann mit dem Messanhänger vornehmlich der Einfluss der Oberflächeneigenschaften von verschiedenartigen Fahrbahnen untersucht werden. Beide Systeme ergänzen sich und können bei Fragestellungen zum Rollwiderstand sowohl von Reifen als auch von Fahrbahnoberflächen eingesetzt werden.
Das Auto gerät zunehmend in das Spannungsfeld zwischen dem Bedürfnis nach Mobilität und dem Umweltschutz. Viele Maßnahmen zur Reduzierung des Kraftstoffverbrauchs und der Schadstoffemission wurden bereits ergriffen. Nunmehr wird auch dem Rollwiderstand der Bereifung Beachtung geschenkt. Dem Autofahrer werden von mehreren Reifenherstellern sogenannte "rollwiderstandsarme" Reifen angeboten. In den Werbeaussagen der Hersteller wird eine Reduzierung des Rollwiderstandes mit bis zu 30 Prozent angegeben und eine Kraftstoffersparnis von bis zu 5 Prozent versprochen. Durch die Untersuchung der Bundesanstalt für Straßenwesen sollte diese Aussage überprüft werden. Dabei wurden im Prüfstand Fahrzeug/Fahrbahn ingesamt jeweils drei Reifen von drei Herstellern in zwei Reifengrößen (175/70 R13 T und 195/65 R15 H/V) als Normalversion und als rollwiderstandsarme Ausführung bei unterschiedlichen Geschwindigkeiten getestet. Gemessen an den Werbeaussagen konnte lediglich bei einem Reifenhersteller das gesteckte Ziel annähernd erreicht werden.
Ende 1990er Jahre wurde in der Bundesrepublik Deutschland unter Beteiligung von Betreibern und Herstellern mit der Standardisierung offener Schnittstellen für die Straßenverkehrstechnik (Open Communication Interface for Road Traffic Control Systems = OCIT) begonnen. Das Ziel der Entwicklung lautet, offene und vereinheitlichte Kommunikation zum Datenaustausch zwischen Geräten der Straßenverkehrstechnik zu ermöglichen. Die Dimension des hierzu erforderlichen Schnittstelleninnovationsprozesses zur Schaffung von OCIT per se und die Vielfalt der daran zu beteiligenden Hersteller und Betreiber manifestierten bereits zum Beginn der Standardisierungsarbeiten den hohen wie anspruchsvollen Bedarf und, ambivalent hierzu, die damit einhergehenden Entwicklungsrisiken aller Akteure dieses Vorhabens. Zehn Jahre später nun lassen sich aus heutiger Sicht die erreichten Standardisierungsergebnisse chronologisch resümieren und die Erfahrungen aus dem bisherigen Standardisierungsprozess perspektivisch auf das zukünftige Standardisierungsgeschehen mit kurzer Darstellung der Einzelsichtweisen der OCIT-Partnerinstitutionen vorausblickend zusammenfassen.
Bestimmte Fragestellungen der Verkehrssicherheitsarbeit und der Unfallforschung, speziell solche zu neuen Informationstechnologien im Fahrzeug, lassen sich nur mit Fahrproben beantworten. In dem Bericht sind bisherige Erfahrungen zusammengestellt, die bei der Durchführung von Fahrproben gemacht wurden. Im einzelnen werden Verfahrensvorschläge für folgende Problembereiche erörtert: Einflussfelder, Untersuchungsinstrumente und Entwicklung von Fahrversuchen; Operationalisierung der Fragestellung; Fahrraumdefinitionen (Fahrraum und Umfeld); Verknüpfung von Situation und Fahrraumumfeld; Grundlagen und Festlegung der statistischen Prüfmethoden; Anforderungen an die Messstrecke, das Messfahrzeug und die Auswerteeinheit; Versuchsdesign und statistische Sicherheitswahrscheinlichkeit; Versuchspersonenauswahl; Homogenisierung der Versuchspersonenstichprobe; Effektstärken; Stichprobengröße; Datenerhebung; Datenstrukturierung; Auswertung sowie Dokumentation. Es handelt sich nicht um ein in sich geschlossenes Methodenbuch, sondern um einen Methodenaufriss einschließlich Literaturangaben.