91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
Volltext vorhanden
- ja (73) (entfernen)
Schlagworte
- Conference (73) (entfernen)
Institut
This work describes the results of the experimental activity, illustrating the driving behavior observed in different conditions, relating them to the different methods of ADAS intervention and comparing the driver behavior without ADAS. In the present study, driver behavior was studied in road accidents involving elderly pedestrians, with different ADAS HMIs, as a base to develop a driver model in near missing pedestrian accidents. A literature research was conducted with the aim of finding out the main influencing factors, including environment, boundary conditions, configuration of impact, pedestrian and driver information, when pedestrian fatalities occur and an analysis of frequent road accidents was conducted to get more detailed information about the driver- behavior. In order to obtain more detailed information about pedestrian accidents, real road accidents were reconstructed with multibody simulations on PC-Crash and, by the comparison between literature findings and reconstructions, a generic accident scenario was defined. The generic accident scenario was implemented on the full scale dynamic driving simulator in use at the Laboratory for Safety and Traffic Accident Analysis (LaSIS, University of Florence, Italy) in order to analyse the driving behaviors of volunteers, also considering the influence of ADAS devices. Forty-five young volunteers were enrolled for this study, resulting in forty valid tests on different testing scenarios. Two different scenarios consisted in driving with or without ADAS in the vehicle. Different kinds of ADAS, acoustic and optical, with different time of intervention were tested in order to study the different reactions of the driver. The tests showed some interesting differences between driver's behavior when approaching the critical situation. Drivers with ADAS reacted earlier, but more slowly, depending also on the type of alarm, and often with double reaction when braking. In fact, the results of the activity showed that with ADAS intervention the time to collision (TTC) increases, but the reaction time and braking modality change: a) there is a sort of "latency" time between the accelerator pedal release and the brake pressure; b) the brake pressure is initially less intense. So the driver only partially takes advance from the TTC increase. These differences were valued not only qualitatively, but quantitatively as well. This work revealed to be useful to improve the knowledge of drivers" behavior, in order to realize a driver model that can be implemented to help attaining and assessing higher levels of automation through new technology.
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
For more than a decade, ADAC accident researchers have analysed road accidents with severe injuries, recording some 20,000 accidents. An important task in accident research is to determine the causative factors of road accidents. Apart from vehicle engineering and human factors, accident research also focuses on infrastructural and environmental aspects. To find out what accident scenarios are the most common in ADAC accident research and what driver assistance systems can prevent them, our first task was to conduct a detailed accident analysis. Using CarMaker, we performed a realistic simulation of accident scenarios, including crashes, with varying parameters. To begin with, we made an initial selection of driver assistance systems in order to determine those with the greatest accident prevention potential. One important finding of this study is that the safety potential of the individual driver assistance systems can actually be examined. It also turned out that active safety offers even much more potential for development and innovation than passive safety. At the same time, testing becomes more demanding, too, as new systems keep entering the market, many of them differing in functional details. ADAC will continue to test all driver assistance systems as realistically as possible so as to be able to provide advice to car buyers. Therefore, it will be essential to develop and improve test conditions and criteria.
Twenty-eight percent of traffic accidents in Japan are rear-end collisions, and of these, 13% are multiple collisions (three or more vehicles and/or roadside objects). A post-crash braking system enables the driver to stop the vehicle in a short distance after a rear-end collision to prevent secondary collisions. In this study, the effectiveness of a post-crash braking system was examined using a drive recorder database. In 64% of rear-end collisions, the driver's braking was interrupted after the collision. The stopping distance was estimated with time data from the drive recorder. We predict that the brake assist would be effective in preventing secondary collisions in 21% of cases.
Injury probability functions for pedestrians and bicyclists based on real-world accident data
(2017)
The paper is focusing on the modelling of injury severity probabilities, often called as Injury Risk Functions (IRF). These are mathematical functions describing the probability for a defined population and for possible explanatory factors (variables) to sustain a certain injury severity. Injury risk functions are becoming more and more important as basis for the assessment of automotive safety systems. They contribute to the understanding of injury mechanisms, (prospective) evaluation of safety systems and definition of protection criteria or are used within regulation and/or consumer ratings. In all cases, knowledge about the correlation between mechanical behavior and injury severity is needed. IRFs are often based on biomechanical data. This paper is focusing on the derivation of injury probability models from real world accident data of the GIDAS database (German In-depth Accident Study). In contrast to most academic terms there is no explicit term definition or definition of creation processes existing for injury probability models based on empirical data. Different approaches are existing for such kind of models in the field of accident research. There is a need for harmonization in terms of the used methods and data as well as the handling with the existing challenges. These are preparation of the dataset, model assumptions, censored/unknown data, evaluation of model accuracy, definition of dependent and independent variable, and others. In the presented study, several empirical, statistical and phenomenological approaches were analyzed regarding their advantages and disadvantages and also their applicability. Furthermore, the identification of appropriate prediction parameters for the injury severity of pedestrians has been considered. Due to its main effect on injuries of pedestrians and bicyclists, the importance of the secondary impact has also been analyzed. Finally, the model accuracy, evaluated by several criteria, is the rating factor that gives the quality and reliability for application of the resulting models. After the investigation and evaluation of statistical approaches one method was chosen and appropriate prediction variables were examined. Finally, all findings were summarized and injury risk functions for pedestrians in real world accidents were created. Additionally, the paper gives instructions for the interpretation and usage of such functions. The presented results include IRFs for several injury severity levels and age groups. The presented models are based on a high amount of real world accidents and describe very well the injury severity probability of pedestrians and bicyclists in frontal collisions with current vehicles. The functions can serve as basis for the evaluation of effectiveness of systems like Pedestrian-AEB or Bicycle-AEB.
In most of developed countries, the progress made in passive safety during the last three decades allowed to drastically reduce the number of killed and severely injured especially for occupants of passenger cars. This reduction is mainly observed for frontal impacts for which the AIS3+ injuries has been reduced about 52% for drivers and 38% for front passengers. The stiffening of the cars' structure coupled with the generalization of airbags and the improvement of the seatbelt restraint (load limiter, pretension, etc.) allowed to protect vital body regions such as head, neck and thorax. However, the abdomen did not take advantage with so much success of this progress. The objective of this study is to draw up an inventory on the abdominal injuries of the belted car occupants involved in frontal impact, to present adapted counter-measures and to assess their potential effectiveness. In the first part the stakes corresponding to the abdominal injuries will be defined according to types of impact, seat location, occupants' age and type of injured organs. Then, we shall focus on the abdominal injury risk curves for adults involved in frontal impact and on the comparisons of the average risks according to the seat location. In the second part we will list counter-measures and we shall calculate their effectiveness. The method of case control will be used in order to estimate odds ratio, comparing two samples, given by occupants having or not having the studied safety system. For this study, two type of data sources are used: national road injured accident census and retrospective in-depth accident data collection. Abdominal injuries are mainly observed in frontal impact (52%). Fatal or severe abdominal occupant- injuries are observed at least in 27% of cases, ranking this body region as the most injured just after the thorax (51%). In spite of a twice lower occupation rate in the back seats compared to the front seats, the number of persons sustaining abdominal injuries at the rear place is higher than in the front place. In recent cars, the risk of having a serious or fatal abdominal injury in a frontal impact is 1.6% for the driver, 3.6% for the front passenger and 6.3% for the rear occupants. The most frequently hurt organs are the small intestine (17%), the spleen (16%) and the liver (13%). The most common countermeasures have a good efficiency in the reduction of the abdominal injuries for the adults: the stiffness of the structure of the seats allows decreasing the abdominal injury risk from 54% (driver) to 60% (front occupant), the seatbelt pretensioners decrease also this risk from 90% (driver) to 83% (front passenger).
From an automotive safety occupant protection standpoint, effective occupant restraint requires a system capable of providing non-injurious occupant ride down of anticipated crash forces. This is not only the case for frontal collisions, where occupant restraint is provided primarily by seatbelts and airbags, but is also critical for other crash modes such as side impacts, rear impacts, rollovers, as well as multiple impact events. In the rear impact crash mode, occupant restraint is provided primarily by the seatbacks and to some extent the seatbelts. Foundationally, therefore, what becomes fundamental to the seatback's role in rear occupant protection is its ability to contain the occupant within the seat, preventing occupant ramping, as well as preventing the seat's, and/or its occupant's, dangerous intrusion into the rear occupant's survival space where contact with rear compartment components and/ or rear seated occupants can present a significant injury risk. An analysis is presented of a series of rear impact sled testing conducted by the authors that evaluates the timing, position and extent of the front seatback's reward displacement toward and into the rear occupant compartment as well as consideration of the front seat occupant' ramping potential and its injury potential relative to the rear compartment. Additionally, three other series of testing are presented which assess various seat designs occupant retention capabilities. Lastly, a matched-pair comparison test series is presented which evaluates occupant motion in rear impact with and without use of a typical vehicle body mounted 3-point seatbelt. Discussion of restraint system performance observed in all the testing is included along with ATD biofidelity and thigh-gap considerations. The data collected and presented includes accelerometer instrumentation and high speed video analysis.
This study investigates the protection offered by passive head-restraints with different stiffness and energy dissipation properties. For this purpose, computational multi-body models of a generic car seat and a biofidelic 50thpercentile male human for rear impact are used to study different seat designs and passive head-restraints. The validated seat-occupant model is also used in the design of two different car-seat models which are shown to effectively mitigate whiplash by utilising a crash-energy distribution technique. Five different passive head-restraints with varying stiffness (low-medium-high) and energy dissipation percentages (low-high) are successively attached to four different car-seat models. The simulation results indicate that the protection offered by head restraints is strongly dependent on the seat design. It has also been shown that the stiffness of the passive head-restraint has much more influence on whiplash-risk in comparison to its energy dissipation capacity.
The incidence of side impacts was investigated from GIDAS data. Both vehicle-fixed object and vehicle-vehicle collisions were analysed as these are enclosed within the consumer testing program. Vehicle-fixed object collisions were stratified according to ESC availability. Results indicated that vehicles equipped with ESC rarely have pure-lateral impacts. An increase in oblique collisions was seen for the vehicles with ESC whereby most vehicle were driving in left curves. The analysis of vehicle-vehicle collisions developed injury risk curves were developed at the AIS3+ injury severity for the vehicle-vehicle side impacts. Results suggested that greatest injury risk occurred when a Pre Euro NCAP vehicle was struck by a Post Euro-NCAP vehicle. The remaining curves did not show different behaviour, indicating that stiffness increased have been equally combated. This was attributable to the few Post Euro-NCAP vehicles that had a deployed curtain airbag available in the sample. The integration of Euro NCAP testing has shown to improve vehicle crashworthiness for pole collisions, as those vehicles with ESC rarely incur lateral impacts.
At IAM RoadSmart we share the excitement about autonomous cars " who wouldn't! However over half of the drivers we polled supported concentrating on making drivers safer " among IAM RoadSmart members it was 70%. Driverless cars are still years away but delivering safer drivers can help reduce death and injury from tomorrow. Governments, academics and car makers need to work hard to convince sceptical British and American drivers that autonomous cars can deliver the benefits promised such as a 90% plus reduction in road deaths.
In 2016 the seventh ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Assessment of the effectiveness of Intersection Assistance Systems at urban and rural accident sites
(2015)
An Intersection Collision Avoidance System is a promising safety system for accident avoidance or injury mitigation at junctions. However, there is still a lack of evidence of the effectiveness, due to the missing real accident data concerning Advanced Driver Assistance Systems. The objective of this study is the assessment of the effectiveness of an Intersection Collision Avoidance System based on real accidents. The method used is called virtual pre-crash simulation. Accidents at junctions were reconstructed by using the numerical simulation software PC-Crashâ„¢. This first simulation is called the baseline simulation. In a second step the vehicles of these accidents were equipped with an Intersection Collision Avoidance System and simulated again. The second simulation is called the system simulation. In the system simulation two different sensors and four different intervention strategies were used, based on a time-to-collision approach. The effectiveness of Intersection Collision Avoidance System has been evaluated by using an assessment function. On average 9% of the reviewed junction accidents could have been avoided within the system simulations. The other simulation results clearly showed a change in the principal direction of force, delta-v and reduction of the injury severity.
Event data recorders (EDRs) are a valuable tool for in-depth investigation of traffic accidents. EDRs are installed on the airbag control module (ACM) to record vehicle and occupant information before, during, and after a crash event. This study evaluates EDR characteristics and aims at better understanding EDR performance for the improvement of accident reconstruction with more reliable and accurate information regarding accidents. The analysis is based on six crash tests with corresponding EDR datasets.
The Traffic Accident Research Institute at University of Technology Dresden investigates about 1,000 accidents annually in the area around and in Dresden. These datasets have been summarized and evaluated in the GIDAS (German Accident In-Depth Study) project for 13 years. During the project it became apparent that the specific traffic situation of a covert exit of a passenger car and an intersecting two-wheeler involves a high risk potential. This critical situation develops in a large part due to the lack of visibility between the driver and the intersecting bike. In this paper the accident avoidance potential of front camera systems with lateral field of view, which allows the driver to have an indirect sight into the crossing street area will be presented.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
This study aimed at developing an injury estimation algorithm for AACN technologies for Germany and compared them to findings based on Japanese data. The data to build and to verify the algorithm was obtained from the German in-depth Accident Database (GIDAS) and split into a training and a validation dataset. Significant input variables and the generalized linear regression model to predict severe injuries (ISS>15) were selected to maximize area under the receiver operating characteristic curve (AUC). Probit regression with the input parameter multiple impact, delta v, seatbelt use and impact direction gave the largest AUC of 0.91. Sensitivity of the algorithm was validated at 90% and specificity at 76% for an injury risk threshold of 2%. It appears that no major differences between Japan and Germany exist for injury estimation based on delta v and impact direction. However, far side impact and multiple crash events appear to be associated with a larger risk increase in the German data.
The current Brussels EU Regulation No. 1235/2011, valid from May 30, 2012, has introduced an European Tyre Label with wet grip index G classes from A to G for passenger car tyres C1, light commercial vehicles tyres C2 and heavy truck- and bus tyres C3. Every wet grip class for each vehicle category has a defined band of numerical values for the wet grip index G. The legislated wet grip values G in this EU- Regulation are very low. The measured braking distances and corresponding impact speeds of the test vehicles are showing very critical results. Regulation No. 1235/2011 of the European Parliament and the Council for Type Approval of Vehicles (EU) should be changed in such a way, that for C1-tyres (normal passenger cars tyres) the minimum wet grip index G is 1.25. All C2-tyres (light commercial vehicles tyres) should at least meet a minimum wet grip index of G = 1.1. All C3-tyres (heavy trucks and buses tyres) should at least meet a minimum wet grip index of G = 0.95. Due to the missing lower limits for G in the wet grip class F for C1, C2 and C3 tyres according to Commission Regulation (EU) No. 1235/2011, officially valid from 30 May 2012, a tyre-to-road coefficient of adhesion in the extreme of 0 (zero) is legally permitted. This is an apparent flaw in above cited EU Regulation, which causes a potential danger to the road traffic safety for all motor vehicles in Europe with such tyres. The wet grip class F has to be removed urgently from said EURegulation, since a direct liability of the responsible EU-Commission can not be excluded.
Today's volumes of traffic require more and more responsibility from each individual road user in their interactions. Those who drive motor vehicles have the singular obligation to minimise the risk of accidents and hence the severity of injuries, particularly with a view to the most vulnerable road users such as motor bikes, bikes and pedestrians. Since responsible and pro-active driving depends first and foremost on the visual information relayed by our eyes and the visual channel this requires good command of the traffic and all-round visibility from our driver's seat. Granted that human error can never be fully excluded, improving visibility around the car is nevertheless an urgent priority. To do so, we need to rate visibility in the most realistic driving situations. Since the existing visibility metrics and methodology are not applicable to real-life driving situations, this study aimed at developing a new visibility rating methodology based on real-life accident scenarios. On the basis of the cases documented by the accident research project, this study analysed criteria indicative of diminishing visibility on the one hand and revealing some peculiarities in connection with the visibility issue on the other. Based on the above, the project set out to develop a rating methodology allowing to assess all-round visibility in various road situations taking into account both driver and road geometries. In this context, the assessment of visibility while turning a corner, crossing an intersection and joining traffic on a major road (priority through route) is of major importance. The first tests have shown that critical situations can be avoided by adapting the relevant geometries and technical solutions and that significant improvements of road safety can be derived therefrom.
For the estimation of the benefit and effect of innovative Driver Assistance Systems (DAS) on the collision positions and by association on the accident severity, together with the economic benefit, it becomes necessary to simulate and evaluate a variety of virtual accidents with different start values (e.g. initial speed). Taken into account the effort necessary for a manual reconstruction, only an automated crash computation can be considered for this task. This paper explains the development of an automated crash computation based on GIDAS. The focus will be on the design of the virtual vehicle models, the method of the crash computation as well as exemplary applications of the automated crash computation. For the first time an automated crash computation of passenger car accidents has been realized. Using the automated crash computation different tasks within the field of vehicle safety can be elaborated. This includes, for example, the calculation of specific accident parameters (such as EES or delta-V) for various accident constellations and the estimation of the economic benefit of DAS using IRFs (Injury Risk Functions).
The project UR:BAN "Cognitive assistance (KA)" aims at developing future assistance systems providing improved performance in complex city traffic. New state-of-the-art panoramic sensor technologies now allow comprehensive monitoring and evaluation of the vehicle environment. In order to improve protection of vulnerable road users such as pedestrians and cyclists, a particular objective of UR:BAN is the evaluation and prediction of their behaviour and actions. The objective of subproject "WER" is development support by providing quantitative estimates of traffic collisions at the very start and predict potential in terms of optimized accident avoidance and reduction of injury severity. For this purpose an integrated computer simulation toolkit is being devised based on real world accidents (GIDAS as well as video documented accidents), allowing the prediction of potential effectiveness and future benefit of assistance systems in this accident scenario. Subsequently, this toolkit may be used for optimizing the design of implemented assistance systems for improved effectiveness.
The evaluation of the expected benefit of active safety systems or even ideas of future systems is challenging because this has to be done prospectively. Beside acceptance, the predicted real-world benefit of active safety systems is one of the most important and interesting measures. Therefore, appropriate methods should be used that meet the requirements concerning representativeness, robustness and accuracy. The paper presents the development of a methodology for the assessment of current and future vehicle safety systems. The variety of systems requires several tools and methods and thus, a common tool box was created. This toolbox consists of different levels, regarding different aspects like data sources, scenarios, representativeness, measures like pre-crash-simulations, automated crash computation, single-case-analyses or driving simulator studies. Finally, the benefit of the system(s) is calculated, e.g. by using injury risk functions; giving the number of avoided/mitigated accidents, the reduction of injured or killed persons or the decrease of economic costs.
In 2014 the sixth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Accident research 2.0: New methods for representative evaluation of integral safety in traffic
(2013)
BMW has developed a procedure for rating Advanced Driver Assistance Systems (ADAS) benefits that integrates two distinct tools. The tool "S.A.F.E.R." is designed to analyze the pre-crash phase. The aim of S.A.F.E.R. is to simulate all relevant processes in sufficient detail to obtain reproducible estimates of key indicators (effectiveness, false positives, etc.). The relevant processes include not only traffic and vehicle dynamics, but also environmental and most importantly human factors. Representative distributions of factors and parameters are obtained by taking the stochastic variation of all relevant parameters into account in the simulations. The second tool, known as "ICOS", has been designed to provide a high-resolution, high-fidelity description of crash phase dynamics. If one converts the outputs of stochastic simulation into inputs for crash dynamics, the result is a comprehensive description of exactly how a safety system can reduce injuries. Applications currently focus on high-fidelity simulation of individual crashes in order to enhance our understanding and optimization of connected safety systems. An integrated simulation process thus allows an exact prediction of the effectiveness in individual cases in terms of injury severity. The development and rating of integral safety need to reflect the true efficiency in the field. The integrated approach described here could provide a valid and reproducible basis for rating connected systems of active and passive safety. In particular, "virtual experiments" using a traffic-based approach and incorporating models of all relevant processes constitute an essential element of the approach.
The presentation deals with the simulation tool rateEFFECT which intends to answer the following questions: Which active safety systems should be developed to maximize safety benefit in real traffic accidents? What is the effectiveness of a specific active safety system in the real world? How many casualties could be avoided by such a system? It is shown that a lot of information is required to simulate existing accidents in order to estimate ADAS effects. This particularly includes numerical values for the pre-crash and in-crash phase. The database GIDAS provides a required minimum number of these parameters for a statistically significant sample.
The misuse of CRS (child restraint system) is one of the most urgent problems in connection of child safety in cars. Numerous field studies show that more than two thirds of all CRS are used in a wrong way. This misuse could lead to serious injuries for the children. Surprisingly the quality of CRS use is coded much better in accident data (e.g. GIDAS) than the results of observatory field studies show. It is expected that misuse of CRS was not detected by the accident teams in a large number of the cases. An essential part in improving child seats and their usability is the knowledge of the relation between misuse and resulting injuries. For that the analysis and experimental reconstruction of accidents is an important part. For allowing an exact experimental accident reconstruction, it is necessary to have detailed information about the securing situation of the child and about the installation of the CRS in the car.
Automotive interiors have long been a potentially injurious impact area to occupants during accidents, especially in the absence of adequate padding. The U.S. Federal Motor Vehicle Safety Standard (FMVSS) 201, Occupant Protection in Interior Impact, outlines test procedures and performance criteria in order to mitigate potentially injurious head impacts to interior surfaces. FMVSS 201 specifies a finite set of impact locations and applies to passenger vehicles of a specified year range and with a gross vehicle weight rating less than 10,000 lb. In this paper, two head impact test methodologies are presented, a pendulum-test device and a Free Motion Headform (FMH) launching device, which allows for dynamic, repeatable impact evaluation of various vehicle interior surfaces and their impact attenuation abilities. The presented testing includes multiple series that evaluate the effect of differing vehicle upper interior padding on occupant head injury. One study in particular, analyzes a head impact to the side header of a heavy truck (not included in FMVSS 201) during a 90 degree rollover. Additionally, two other series of tests are presented which assess the injury reduction effect of side airbags to near side as well as far side occupants in a side impact scenario. Lastly, a forensic analysis is presented which evaluates two possible head impact locations experienced in a real world accident by analysis of the resulting interior compartment damage utilizing the FMH launching device test method. The data collected and presented includes accelerometer instrumentation and high speed video analysis. These studies demonstrate that adequate padding and airbags are very effective at mitigating head injury potential at impact speeds of 12-25 mph (19-40 kph).
Rollovers continue to be a major source of heavy truck fatalities when compared to other accident modes. Real world rollover accidents are analyzed and two distinct damage patterns are identified. Damage to heavy truck roofs can occur from lateral loading that transitions to vertical roof loading as the vehicle rolls onto its side and then over onto its roof. A second load path can occur when the vehicle has rolled onto its side and furrows into the ground generating large longitudinal friction forces between the roof and ground. A review of the previous literature and various test methodologies are presented. A sled impact test methodology is presented which allows for structural assessment of a heavy truck cab's crashworthiness in both of these loading environments. Two test series are presented using the sled impact test methodology in order to analyze real world truck rollovers using varying impact platen and contact angles. The structural deformation and failure patterns were found to be consistent with damage seen in real world accident vehicles. In each case, a second equivalent truck cab was then reinforced and tested under similar conditions to evaluate the energy management and crush resistance of a stronger cab structure. These structural reinforcements demonstrated a substantial reduction in roof crush and protected the survival space of the occupant compartment. The sled impact test procedure is an effective method for testing the structural performance of a heavy truck cab in a variety of loading scenarios comparable to real world accidents and ascertaining the load and energy load levels in these accident modes.
The European CASPER (Child Advanced Safety Project for European Roads) project studying car child safety includes a sociological approach in order to have a better understanding of the behaviour of parents driving children under 12 years old. A questionnaire was distributed via the internet in Europe with 998 parents (representing 1638 children) from 22 European countries responding. The results inform on the way parents secure their children during a car trip. Many parents did not control how their children were installed in the child restraint system (CRS). A toddler was more likely to travel into a child seat than an older child was. Regarding misuse situations, an important part of the participants did not think that they could make mistakes when fixing the child seat to the car (26%) or when placing the child into the seat (39%). This leaves an important field of action especially by communication via different media and in the CRS sale outlets.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
Die EU hat für die Verkehrssicherheit in Europa ein anspruchsvolles Ziel vorgegeben: Bis 2010 soll die Anzahl der im Straßenverkehr Getöteten gegenüber 2000 halbiert werden. Für Deutschland kann eine erfolgreiche Zwischenbilanz gezogen werden: In den letzten 5 Jahren nahm trotz Vergrößerung des Kraftfahrzeugbestandes um 6% die Anzahl der Verkehrstoten um 29% ab, in den vergangenen 10 Jahren ist ein Rückgang um 43% zu verzeichnen. Diese im internationalen Vergleich überdurchschnittlichen Erfolge sind nicht zuletzt auch auf Fortschritte in der Fahrzeugtechnik zurückzuführen, wobei die zunehmende Verbreitung von Systemen der Aktiven Sicherheit wie ABS, BAS, ESP einen entscheidenden Anteil hat. Nach der deutlichen Reduzierung von Fahrunfällen durch ESP-® stehen nun die Auffahrunfälle im Fokus der Sicherheitsentwicklung von Mercedes-Benz. Das Paket aus verbessertem rückwärtigen Signalbild (Adaptives Bremslicht) und Brems-Assistent (BAS) wurde kürzlich durch radarbasierte Bremsassistenz ergänzt (BAS PLUS und PRE-SAFE-®-Bremse). Der Beitrag geht auf Funktion und Wirksamkeit der einzelnen Systeme ein und gibt einen Ausblick in die nähere Zukunft.
Motorcycle safety research
(2007)
Honda- global motorcycle sales exceeded the 10 million units mark since 2004, and further expansion is expected. As a responsibility for a company to provide mobility, Honda is focusing on motorcycle safety as top priority and has been working on various activities for both aspects of hardware and software. Here, we present Honda- activity for the safety technology of motorcycles. At present, Honda is promoting motorcycle safety in the four themes of prevention and collision safety such as safety education, recognition assistance, accident prevention and injury reduction. First, in the area of the safety education, the "Honda Safety Driving Promotion Center" was established in 1970, and motorcycle riders and vehicle driver trainings have been organized, and the traffic training centers are used as an actual practice field not only in Japan but also in many other regions in the world. Through our training activities, the new area of safety training with hardware assistance was developed and Honda- unique technology was accumulated such as the riding simulator which can provide experience of potentially dangerous situations without risk. Especially, the "riding trainer", the popular version of the riding simulator, was introduced at several motor shows in various countries and launched in September 2005. It was distributed first in Europe and is expected to expand globally aiming at 3000 units worldwide.. And in Europe, the newest version, which includes the suburban roads program, jointly developed with ADAC, will be released in near future. In the area of recognition assistance, "vehicle to vehicle communication technology" is under development using the advantage of being a manufacturer of both motorcycles and cars. This technology is under research as Honda "ASV-3" in Japan, and as part of C2C activity in Europe. As for the accident prevention, advanced brake systems for motorcycles to assist more effective brake operation have been expanded, Honda signed the European Road Safety Charter in April 2004 with the advanced brake systems commitment and furthermore, they are expanding according to vehicle characteristics and region. Then all models above 250 cc will have a version of the system by 2010. And as the last theme, "motorcycle airbag system" is introduced which is equipped on a mass production motorcycle for the first time in the world. It has been researched and developed for a long time as an injury reduction technology for collision accidents. Honda automobile technology was used for the research and development of the motorcycle airbag, and many specific issues such as the analysis of the collision conditions particular to motorcycles have been solved to realize today- success. It might be known that ADAC in-house crash test held in August this year confirmed the high effectiveness of the airbag system and showed a positive result. This motorcycle airbag system is equipped to the Honda Gold Wing and launched in North America in August, 2006. Also in Europe, it will be sold by the end of this year. Each theme of Honda motorcycle safety technology can be seen at the Honda booth.
The overall purpose of the ASSESS project is to develop a relevant and standardised set of test and assessment methods and associated tools for integrated vehicle safety systems, primarily focussing on currently available pre-crash sensing systems. The first stage of the project was to define casualty relevant accident scenarios so that the test scenarios will be developed based on accident scenarios which currently result in the greatest injury outcome, measured by a combination of casualty severity and casualty frequency. The first analysis stage was completed using data from a range of accident databases, including those which were nationally representative (STATS19, UK and STRADA, SE) and in-depth sources which provided more detailed parameters to characterise the accident scenarios (GIDAS, DE and OTS, UK). A common analysis method was developed in order to compare the data from these different sources, and while the data sets were not completely compatible, the majority of the data was aligned in such a way that allowed a useful comparison to be made. As the ASSESS project focuses on pre-crash sensing systems fitted to passenger cars, the data selected for the analysis was "injury accidents which involved at least one passenger car". The accident data analysis yielded the following ranked list of most relevant accident scenarios: Rank Accident scenario 1 Driving accident - single vehicle loss of control 2 Accidents in longitudinal traffic (same and opposite directions) 3 Accidents with turning vehicle(s) or crossing paths in junctions 4 Accidents involving pedestrians The ranked list highlights the relatively large role played by "accidents in longitudinal traffic", and "accidents with turning vehicle(s) or crossing paths in junctions" (the second and third most prevalent accident scenarios, respectively). The pre-crash systems addressed in ASSESS propose to yield beneficial safety outcomes with specific regard to these accident scenarios. This indicates that the ASSESS project is highly relevant to the current casualty crash problem. In the second stage of the analysis a selection of these accident scenarios were analysed further to define the accident parameters at a more detailed level .This paper describes the analysis approach and results from the first analysis stage.
This work aims at bringing evidence for mass incompatibility in frontal impact for cars built according to the UNECE R94 regulation. French national injury accidents database census for years 2005 to 2008 were used for the analysis. The heterogeneity of frontal self-protection among cars of different masses is investigated, as well as the partner protection parameter offered by these cars. The last part of the analysis deals with the estimation of the benefit, in terms of fatal and severe injuries avoided, if crashworthiness was harmonized for the whole fleet of vehicle. This calculation is done for France and is extended to all Europe.
An analysis of NASS and FARS was conducted to determine crash conditions that involved injuries that are not currently being directly addressed by vehicle safety standards or by consumer information test protocols. Analysis of both field data and US NCAP tests were conducted to determine the relative safety provided by seating position and by vehicle model year. Opportunities for improvements were determined by crash categories with large populations of injuries that were not addressed by safety tests or smaller numbers that were increasing in frequency. Areas of opportunities include improved occupant restrain in rollovers, improved frontal protection for rear seat occupants and improved fire prevention in frontal and rollover crashes.
The share of high-tensile steel in car bodies has increased over the last years. While occupant safety has generally benefited from this measure, there is a potential risk that, as a result, rescue time may increase considerably. In more than 60% of all car occupant fatalities a technical rescue has been necessary. These are in particular those cases where occupants die immediately at the accident scene. Therefore, in these cases "rescue time" is a very sensitive parameter. In addition to the general analysis of the need of technical rescue and the actual rescue time depending on model years, the injury pattern of occupants requiring technical rescue will be analysed to provide advice for rescue teams. Furthermore, a detailed analysis of rescue measures for the most popular car models depending on the safety cell design is given.
The paper presents a methodology for the benefit estimation of several secondary safety systems for pedestrians, using the exceptional data depth of GIDAS. A total of 667 frontal pedestrian accidents up to 40kph and more than 500 AIS2+ injuries have been considered. In addition to the severity, affected body region, exact impact point on the vehicle, and the causing part of every injury, the related Euro NCAP test zone was determined. One results of the study is a detailed impact distribution for AIS2+ injuries across the vehicle front. It can be stated, how often a test zone or vehicle part is hit by pedestrians in frontal accidents and which role the ground impact plays. Basing on that, different secondary safety measures can be evaluated by an injury shift method concerning their real world effectiveness. As an example, measures concerning the Euro NCAP pedestrian rating tests have been evaluated. It was analysed which Euro NCAP test zones are the most effective ones. In addition, real test results have been evaluated. Using the presented methodology, other secondary safety like the active bonnet (pop-up bonnet) or a pedestrian airbag measures can be evaluated.
Qualität von on-trip Verkehrsinformationen im Straßenverkehr : BASt-Kolloquium 23. und 24.03.2011
(2011)
Am 23. und 24. März 2011 veranstaltete die Bundesanstalt fuer Straßenwesen ein, um die Ergebnisse der erwähnten Projekte und Initiativen präsentieren zu lassen und mit anderen Experten zu diskutieren. Der vorliegende Tagungsband fasst die Ergebnisse des Kolloquiums zur "Qualität von on-trip Verkehrsinformationen" zusammen. Die Bereitstellung von Verkehrsinformationen ist geprägt von vielen Akteuren. Die Wertschöpfungskette beginnt bei der Sammlung grundlegender Verkehrsdaten zur Erstellung von Verkehrsinformationen und setzt sich mit der Datenverarbeitung und -interpretation bis hin zur Meldungserstellung fort. Die Weitergabe kann über verschiedene Übertragungsmedien erfolgen und beim Nutzer (z.B. im Navigationsgerät) empfangen werden. Jeder einzelne Schritt der Wertschoepfungskette kann sowohl von unterschiedlichen Partnern (privat oder öffentlich) übernommen werden als auch in der Hand eines Partners liegen. Diese Komplexität der Zusammenarbeit spiegelt sich demzufolge auch in Qualitätsmanagementprozessen wider. Im Rahmen des Kolloquiums wurden zwei wesentliche Qualitätsaspekte näher betrachtet: - die Datenqualität mit dem Focus auf Aktualitaet, Stimmigkeit der Daten verglichen mit einer gemessenen Realitaet sowohl zu Beginn der Wertschöpfungskette als auch an jeglichen Schnittstellen, - die Prozessqualität, welche sich insbesondere mit der reibungslosen Datenübergabe an den Schnittstellen der Wertschoepfungskette beschäftigt. Beide Qualitätsaspekte helfen zu verstehen, worin die heutigen Qualitätsprobleme bestehen und welche Massnahmen im Einzelnen ergriffen werden müssten, um eine nachhaltige Verbesserung zu erreichen. Einerseits kann es vorkommen, dass die Information über ein Verkehrsereignis an einer oder mehreren Stellen der Wertschöpfungskette korrekt vorliegt, jedoch durch ungenuegende technische oder organisatorische Schnittstellen im Prozessablauf wieder verloren geht und dem Nutzer folglich nicht zur Verfügung steht. Prominentes Beispiel eines solchen Problems in der Prozessqualität ist die fehlerhafte Interpretation der Meldung im Navigationsgerät, denkbar sind solche Informationsverluste jedoch an jeder Stelle der Wertschoepfungskette. Eine wichtige Massnahme zur Verbesserung der Prozessqualität ist die Standardisierung sowie die Überprüfung, ob die definierten Standards an jeder Stelle der Wertschöpfungskette eingehalten werden. Andererseits kann es vorkommen, dass die Datenqualität in Bezug auf ihre Genauigkeit von Anfang an so schlecht ist, dass der Nutzer eine fehlerhafte oder gar keine Nachricht übermittelt bekommt. Beispiel hierfür ist die Vielzahl von Stauereignissen, die entweder nicht gesendet wurden oder gesendet wurden, obwohl sie nicht vorhanden waren. Eine wichtige Massnahme zur Verbesserung dieser Situation ist die Verbesserung der Ereignisdetektion. Der Tagungsband enthaelt Präsentationen, die den Status Quo analysieren, Methoden zur verbesserten Datenerfassung vorschlagen und Möglichkeiten zur Verbesserung von Daten- und Prozessqualität vorstellen. Offen geblieben sind darüber hinaus folgende Fragestellungen: - Wie kann die Prozessqualität der gesamten Wertschöpfungskette bei der Vielzahl der Partner kontrolliert werden? Wer überwacht die Wertschöpfungskette? Wird hierfuer überhaupt eine zentrale Stelle benötigt? Oder ist es ausreichend, wenn jeder Partner eine angemessene Eingangs bzw. Ausgangskontrolle durchführt? - Obwohl es nur eine Realität gibt, entsteht doch Wettbewerb über die (Qualität der) Information zu dieser Realität. Wie kann Konsistenz zwischen allen Anbietern von sicherheitsrelevanten Informationen erreicht werden? Wo sollte der Wettbewerb enden und wie kann dies technisch, organisatorisch und wirtschaftlich realisiert werden? - Welche Prozesse sollten geschaffen werden, um Partner zu integrieren, die sich nicht an geschaffene Qualitätsstandards halten (z.B. kommerzielle Diensteanbieter, die nicht mit der Verkehrsinformationsszene vernetzt sind)? - Und nicht zuletzt, wie kann die Wahrnehmung des Nutzers über verschiedene Qualitätslevel unterschiedlicher Produkte verbessert werden? Ist der Nutzer in der Lage, die unterschiedlichen Qualitätsstufen von Verkehrssystemen zu unterscheiden? Falls nicht, welche Art von Unterstuetzung braucht der Kunde? Ein "European Information Services Assessment Programme" vergleichbar zu Euro NCAP für Fahrzeuge? Die Ergebnisse des Kolloquiums sollen die laufende Diskussion um die Verbesserung der Qualität von Verkehrsinformationen unterstützen.
Providing effective occupant protection in rollover crashes requires supplying the occupant with a restraint system proven effective in the dynamic rollover accident mode. Preventing ejection and providing restraint sufficient to prevent potentially injurious contacts with both interior and exterior vehicle components is paramount for effective rollover occupant protection. Research has shown that the injury potential can be decreased by closely coupling the occupant to the seat. This paper focuses on the effect of restraint system slack and its relationship to occupant excursion and ejection potential during rollover. Various restraint system configurations are evaluated in rollover-type test environments. A review of prior research is presented prior to presenting new quasi-static vehicle inversion studies conducted with live surrogate occupants. Additionally, dynamic rollover testing utilizing anthropometric test devices (ATDs) is presented. The influence of belt looseness and effects of various restraint designs on the belted occupants' injury potential are discussed.
The need of passive safety devices, able to reduce the accidents and the severity of injuries suffered by motorcyclist, distinctly arises from data on accident statistics. In this paper, the effectiveness of an airbag device fitted in the biker- garments has been verified through various numerical simulations. Two simple test conditions were defined, in order to investigate the performance of the device both for back and front impacts, and simulated at various impact speeds. With the aim of providing more information about the actual capability of the airbag to reduce the severity of the injuries, one of accident scenario described by ISO 13232:2005 has been also investigated, checking the real effectiveness of the airbag strap-based firing system too. Confrontation of injury indexes resulting from simulation with and without airbag made possible a realistic evaluation of the harm reduction induced by the airbag presence.
In order to enable foreseeing or comparing the benefit of safety systems or driver assistance systems in Germany, in the United States and in Japan, the traffic accident databases in those three countries are examined. The variables used are culpable party, collision partner, accident type, and injury level and the method to re-classify the databases for comparison are proposed. The result indicates that single passenger car fatality is the most frequent in Germany and in the United States, while passenger car vs. pedestrian is the most frequent fatality scenario in Japan. When the casualty by fatality ratio is focused, the greatest difference is observed in rear-end collisions. The ratio of slight injuries in Japan yields about eighteen times as many as those in Germany, and about eight times as many as those in the United States.
Accident data shows that the vast majority of pedestrian accidents involve a passenger car. A refined method for estimating the potential effectiveness of a technology designed to support the car driver in mitigating or avoiding pedestrian accidents is presented. The basis of the benefit prediction method consists of accident scenario information for pedestrian-passenger car accidents from GIDAS, including vehicle and pedestrian velocities. These real world pedestrian accidents were first reconstructed and the system effectiveness was determined by comparing injury outcome with and without the functionality enabled for each accident. The predictions from Volvo Cars" general Benefit Estimation Model are refined by including the actual system algorithm and sensing models for a relevant car in the simulation environment. The feasibility of the method is proven by a case study on a authentic technology; the Auto Brake functionality in Collision Warning with Full Auto Brake and Pedestrian Detection (CWAB-PD). Assuming the system is adopted by all vehicles, the Case Study indicates a 24% reduction in pedestrian fatalities for crashes where the pedestrians were struck by the front of a passenger car.
An eCall device has been mounted on some vehicles in France since 2003. It is an integrated car radio/GSM/GPS system that can be used with a SIM card. When an accident occurs, a call can be sent manually or automatically made to a telephone call centre. Knowing the geographic location, the vehicle identity and the possibility of a direct communication with the people involved enables the nearest emergency services to be called out. In this context, the LAB / CEESAR have set up a study aimed at evaluating the effectiveness of this system. The purpose of this paper is to detail the E-call system evaluation method of effectiveness used and give a global synthesis of the results.
Females sustain Cervical Spine Distortion injury (CSD) more often than males. Most work dealing with the biomechanics background (e.g. injury mechanism/criteria) as well as the application in seat design/testing, focuses on the occupant model of an average male. Therefore the EU-Project ADSEAT (Adaptive Seat to Reduce Neck Injuries for Female and Male Occupants) is aimed at adding a female model for gender balanced research of CSD and improving seat design. An extensive literature review, searching for risk factors and injury criteria for males and females, was accompanied by the evaluation of different databases containing CSD cases. The database evaluations suggests that an anthropometry quite close to the 50%ile female anthropometry as known from crash test dummy design is appropriate. The results presented here form the basis for the future development of a computational female model and the improvement of seat design for better protection of both males and females in the frame of the ADSEAT-Project.
The aim of this study was to evaluate the performance and accuracy of Event Data Recorders (EDRs). The analysis was based on J-NCAP crash tests from 2006"2007, with the corresponding EDR datasets. The pre-crash velocity, maximum delta-V and delta-V versus time history data recorded in the EDRs were compared with the reliable crash test data. The difference between the EDR pre-crash velocity and the laboratory test speed was less than 4 percent. In contrast, in several cases the maximum delta-V and delta-V versus time history data obtained from the EDRs showed uncertainty of measurement in comparisons with the reliable delta-V data. The difference in maximum delta-V in these comparisons was more than 5 percent in 10 of 14 tests and more than 10 percent in 4 of 14 tests. The EDRs underestimated the maximum delta-V in almost all tests. It was also concluded that the calculated acceleration from the EDR delta-V versus time history data showed good agreement with the instrumented accelerometer signal during the collision in almost all tests.
Impact severity is a fundamental measure for all in-depth crash investigation projects. One methodology used in the UK is based on the US Calspan software package CRASH3. The UK- in-depth crash investigation studies routinely use AiDamage3 a software package which is based on an updated version of the original CRASH3 algorithm, including enhancements to the vehicle stiffness coefficients. Real world accident-damaged vehicles are measured and their crush is correlated with a library of stiffness coefficients. These measurements are then used, along with other parameters, to calculate the crash energy and equivalent changes of velocity of the vehicles (delta-v), which is a measure of the impact severity. UK in-depth accident studies routinely validate the crash severity methodologies applied as the vehicle fleet changes. This is achieved by analysing crash test data and using the appropriate residual crush damage and other inputs to AiDamage3 and checking the program- outputs with the known crash severity parameters. This procedure checks, at least in part, the default stiffness values in the data libraries and the reconstruction methods used.
The focus of the technical innovation in the automobile industry is currently changing to sensor based safety systems, which are operating in the pre-crash phase of an accident. To get more information about this pre-crash phase for real accidents a simulation of this phase using the GIDAS database is done. The basics for this simulation are geometrical information about the accident location and the exact accident data out of the GIDAS database. This aggregated information gives the possibility to simulate an exact motion for every accident participant, using MATLAB / SIMULINK, in the pre-crash phase. After the simulation the information about the geometrical positions, the velocities and maneuvers of the drivers to an individual TTC (time to collision) are available. With those results it is possible to develop new useful sensor geometries using pre-crash scatter plots or estimate the efficiency of implemented active safety systems in combination with sensor characteristics. This simulation can be done for every reconstructed accident included in the GIDAS database, so these results can represent a wide spread basis for the further development of active safety systems and sensor geometries and characteristics
In the last years various new driver information and driver assistance systems made their way into modern vehicles and there are yet countless systems underway. However, expenses for both, the development and the construction of these systems are tremendous. Therefore the interest of evaluating systems keeps growing steadily, not only regarding the results of systems developed in the last years but also regarding system ideas. Only if at least a rough benefit estimation is given, the industry can decide which development should be supported. However, there is still a lack of transparency of possible and useful methods for these kinds of estimations. These were analyses and structured in this study.
During the last 5 years, the number of cars fitted with side airbags has dramatically increased. They are now standard equipment, even on many smaller cars or less luxurious vehicles. While some side airbags offer thoracic protection alone, there are those that combine thoracic and head protection (of which most deploy from the seat). Other systems employ separate airbags for head and thorax protection, which are designed to be effective noticeably in a crash against a pole. This paper proposes an evaluation of the effectiveness of side airbags in preventing thoracic injuries to passenger car occupants involved in side crashes. First, the target population (who can take benefit of side airbag deployment and in what circumstances) is defined. Side airbags can be especially effective in cases of impacts on the door with intrusion at a certain impact speed. Then, an example case of a side impact with side airbag deployment is given were side airbag deployment is thought to have had a positive effect on injury outcome. A further case is presented where the impact configuration is likely to have reduced the effect of side airbag deployment on injury outcome. Finally, the estimation of side airbag effectiveness (in terms of additional occupant protection brought exclusively by the airbag) is proposed by comparing injury risk sustained by occupants in (more or less) similar cars (fitted or non fitted with airbags) because, during these years, car structure, and side airbag conception have considerably evolved. In-depth accident data from France, the UK and Germany has been collected. Out of 2,035 side impact accident cases available in the databases, we selected 435 occupants of passenger cars (built from 1998 onwards) involved in an injury accident between year 1998 and year 2004 for EES (Energy Equivalent Speed) values between 20km/h and 50km/h. The occupants, belted or not, were sat on the struck side, whatever the obstacle and type of accidents (intersection, loss of control, etc.). For multiple impact crashes, the side impact is assumed to be the more severe one. Passenger cars were fitted with (96) or without (339) side airbags. Most of the potential risk explanatory variables were correctly and reliably reported in the databases (velocity " impact zone " impact angle " occupant characteristics, etc.). The analysis compared injury risks for different levels of EES and different types of side airbags. A logistic regression model was also computed with injury variables (such as thoracic AIS 2+ or AIS 3+) as the dependant variable and other variables (including airbag type and EES) as explanatory injury risk factors. Results revealed statistically non-significant reductions in thoracic AIS 2+ and AIS 3+ injury risk in side airbag equipped cars in the impact violence range selected (odds ratio between 0.84 and 0.98 depending on types of airbags). The results are discussed. The non-significance is assumed to be due to a low number of cases. Statistical analysis for head injuries was not possible due to the low number of accident cases with passenger cars fitted with head airbags in the databases. Moreover, the discrepancies between the data coming from different countries (especially calculation of EES) might have introduced instability in the analysis.
This study is aimed to investigate the correlations of impact conditions and dynamic responses with the injuries and injury severity of child pedestrians by accident reconstruction. For this purpose, the pedestrian accident cases were selected from Sweden and Germany with detailed information about injuries, accident cars, and accident environment. The selected accident cases were reconstructed using mathematical models of pedestrian and passenger car. The pedestrian models were generated based on the height, weight, and age of the pedestrian involved in accidents. The car models were built up based on the corresponding accident car. The impact speeds in simulations were defined based on the reported data. The calculated physical quantities were analyzed to find the correlation with injury outcomes registered in the accident database. The reconstruction approaches are discussed in terms of data collection, estimating vehicle impact speeds, pedestrian moving speeds and initial posture, secondary ground impact, validity of the mathematical models, as well as impact biomechanics.