91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
Volltext vorhanden
- nein (133) (entfernen)
Schlagworte
- Sicherheit (58)
- Safety (57)
- Bewertung (40)
- Evaluation (assessment) (40)
- Vehicle (39)
- Fahrzeug (38)
- Anfahrversuch (34)
- Impact test (veh) (31)
- Conference (28)
- Test method (28)
- Versuch (27)
- Konferenz (26)
- Prüfverfahren (26)
- Test (26)
- Accident (22)
- Unfall (22)
- Fußgänger (20)
- Pedestrian (20)
- Anthropometric dummy (19)
- Deutschland (19)
- Germany (19)
- Car (18)
- Dummy (17)
- Collision (16)
- Pkw (16)
- Compatibility (15)
- Kompatibilität (15)
- Simulation (15)
- Driver assistance system (14)
- Method (14)
- Passive safety system (14)
- Passives Sicherheitssystem (14)
- Verfahren (14)
- Zusammenstoß (14)
- Fahrerassistenzsystem (13)
- Frontalzusammenstoß (13)
- Head on collision (13)
- Gesetzgebung (12)
- Legislation (12)
- Research project (12)
- Unfallverhütung (12)
- Accident prevention (11)
- Child (11)
- Forschungsarbeit (11)
- Kind (11)
- Analyse (math) (10)
- Analysis (math) (10)
- EU (10)
- Europa (10)
- Europe (10)
- Injury (10)
- Schlag (10)
- Shock (10)
- Verletzung (10)
- Autonomes Fahren (9)
- Autonomous driving (9)
- Driver (9)
- Driver information (9)
- Fahrer (9)
- Fahrerinformation (9)
- Fahrstabilität (9)
- Insasse (9)
- Lkw (9)
- Lorry (9)
- Radfahrer (9)
- Schweregrad (Unfall, Verletzung) (9)
- Technische Vorschriften (Kraftfahrzeug) (9)
- Vehicle handling (9)
- Vehicle occupant (9)
- Vehicle regulations (9)
- Active safety system (8)
- Aktives Sicherheitssystem (8)
- Automatic (8)
- Automatisch (8)
- Biomechanics (8)
- Biomechanik (8)
- Electronic driving aid (8)
- Elektronische Fahrhilfe (8)
- Improvement (8)
- Measurement (8)
- Messung (8)
- Motorcycle (8)
- Motorrad (8)
- Severity (accid (8)
- Severity (accid, injury) (8)
- Technologie (8)
- Technology (8)
- Verbesserung (8)
- injury) (8)
- Cyclist (7)
- Fahrzeugführung (7)
- Head (7)
- Kopf (7)
- Seitlicher Zusammenstoß (7)
- Side impact (7)
- Standardisierung (7)
- Belastung (6)
- Bemessung (6)
- Braking (6)
- Bremsung (6)
- Design (overall design) (6)
- Driving (veh) (6)
- Impact test (6)
- Load (6)
- Prevention (6)
- Risiko (6)
- Safety belt (6)
- Sicherheitsgurt (6)
- Verletzung) (6)
- Alte Leute (5)
- Anti locking device (5)
- Antiblockiereinrichtung (5)
- Ausrüstung (5)
- Benutzung (5)
- Communication (5)
- Deformation (5)
- Deformierbare Barriere (Anpralltest) (5)
- Development (5)
- Entwicklung (5)
- Equipment (5)
- Ergonomics (5)
- Geschwindigkeit (5)
- Headlamp (5)
- Knee (human) (5)
- Kommunikation (5)
- Lenken (Fahrzeug) (5)
- Official approval (5)
- Reifen (5)
- Richtlinien (5)
- Risk (5)
- Scheinwerfer (5)
- Schweregrad (Unfall (5)
- Specifications (5)
- Speed (5)
- Standardization (5)
- Steering (process) (5)
- Tyre (5)
- Use (5)
- Wirtschaftlichkeitsrechnung (5)
- Accident rate (4)
- Aufprallschlitten (4)
- Bein (menschl) (4)
- Brustkorb (4)
- Collision avoidance system (4)
- Cost benefit analysis (4)
- Datenbank (4)
- Decrease (4)
- Driver training (4)
- Efficiency (4)
- Ergonomie (4)
- Fahrausbildung (4)
- Fahrzeuginnenraum (4)
- Fahrzeugsitz (4)
- Impact sled (4)
- Interior (veh) (4)
- Leg (human) (4)
- Leistungsfähigkeit (allg) (4)
- Nacht (4)
- Night (4)
- Norm (tech) (4)
- Old people (4)
- Perception (4)
- Reproducibility (4)
- Reproduzierbarkeit (4)
- Road user (4)
- Seat (veh) (4)
- Sichtbarkeit (4)
- Specification (standard) (4)
- Thorax (4)
- Unfallhäufigkeit (4)
- Verformung (4)
- Verkehrsteilnehmer (4)
- Verminderung (4)
- Sichtbarkeit (4)
- Wahrnehmung (4)
- Airbag (3)
- Antikollisionssystem (3)
- Auffahrunfall (3)
- Bend (road) (3)
- Bicycle (3)
- Brake (3)
- Bremse (3)
- Bus (3)
- Database (3)
- Deformable barrier (impact test) (3)
- Error (3)
- Fahrleistung (3)
- Fahrrad (3)
- Fehler (3)
- Gewicht (3)
- Human body (3)
- Knie (menschl) (3)
- Kraftfahrzeug (3)
- Leuchtdichte (3)
- Luminance (3)
- Menschlicher Körper (3)
- Messgerät (3)
- Modification (3)
- Motorcyclist (3)
- Motorradfahrer (3)
- Policy (3)
- Politik (3)
- Rear end collision (3)
- Reflectivity (3)
- Reflexionsgrad (3)
- Spikesreifen (3)
- Statistics (3)
- Statistik (3)
- Straßenkurve (3)
- Straßenverkehr (3)
- Studded tyre (3)
- Unterfahrschutz (3)
- Vehicle mile (3)
- Verhütung (3)
- Warning (3)
- Weight (3)
- Windschutzscheibe (3)
- Windscreen (veh) (3)
- Active safety (2)
- Adolescent (2)
- Age (2)
- Air bag (restraint system) (2)
- Aktive Sicherheit (2)
- Alter (2)
- Ankündigung (2)
- Apparatus (measuring) (2)
- Autonomes Fahrzeug (2)
- Autonomous vehicle (2)
- Baumusterzulassung (2)
- Bicyclist (2)
- Blendung (2)
- Body (car) (2)
- Braking distance (2)
- Bremsweg (2)
- Cause (2)
- Classification (2)
- Crash Test (2)
- Data acquisition (2)
- Datenerfassung (2)
- Delivery vehicle (2)
- Detection (2)
- Detektion (2)
- Electric vehicle (2)
- Elektrofahrzeug (2)
- Empfindlichkeit (2)
- Fahranfänger (2)
- Fatality (2)
- Federung (2)
- Forschungsbericht (2)
- France (2)
- Frankreich (2)
- Glare (2)
- Griffigkeit (2)
- Highway traffic (2)
- Impact study (2)
- Individueller Verkehr (2)
- Industrie (2)
- Industry (2)
- International (2)
- Jugendlicher (2)
- Karosserie (2)
- Klassifizierung (2)
- Knie (2)
- Kunststoff (2)
- Landstraße (2)
- Mathematical model (2)
- Nummer (2)
- Plastic material (2)
- Private transport (2)
- Prototyp (2)
- Prototype (2)
- Prüfstand (2)
- Rear view mirror (2)
- Recently qualified driver (2)
- Rechenmodell (2)
- Reconstruction (accid) (2)
- Reflectorized material (2)
- Reflexstoffe (2)
- Road network (2)
- Rural road (2)
- Rückspiegel (2)
- Schutz (2)
- Sensitivity (2)
- Sensor (2)
- Skidding resistance (2)
- Straßennetz (2)
- Straßenverkehrsrecht (2)
- Suspension (veh) (2)
- Test rig (2)
- Traffic count (2)
- Transport (2)
- Tödlicher Unfall (2)
- Underride protection (2)
- Unfallrekonstruktion (2)
- Ursache (2)
- Vehicle inspection (2)
- Verkehrserhebung (2)
- Versuchspuppe (2)
- Veränderung (2)
- Visual display (2)
- Zahl (2)
- Zulassung (tech) (2)
- Zusammenstoss (2)
- Abdomen (1)
- Abstandsregeltempomat (1)
- Acceleration (1)
- Accident data (1)
- Accident proneness (1)
- Accompanied driving (1)
- Adaptive cruise control (1)
- Adult (1)
- Aged people (1)
- Angle (1)
- Anhänger (1)
- Anti blocking device (1)
- Antiblockiersystem (1)
- Antikollisisonssystem (1)
- Apparatus (measurement) (1)
- Attention (1)
- Attitude (psychol) (1)
- Aufmerksamkeit (1)
- Autobahn (1)
- Axle (1)
- Battery (1)
- Bau (1)
- Baustoff (1)
- Begleitetes Fahren (1)
- Begrenzungsleuchten (1)
- Behaviour (1)
- Behinderter (1)
- Benefit cost analysis (1)
- Berechnung (1)
- Beschleunigung (1)
- Betriebsverhalten (1)
- Bibliographie (1)
- Bibliography (1)
- Bildschirm (1)
- Blind spot (veh) (1)
- Bonnet (car) (1)
- Brake light (1)
- Bremslicht (1)
- Bruch (mech) (1)
- Bumper (1)
- Calculation (1)
- Calibration (1)
- Carriageway (1)
- Chassis (1)
- Coefficient of friction (1)
- Colour (1)
- Compatiblity (1)
- Components of the car (1)
- Compression (1)
- Construction (1)
- Contact (tyre road) (1)
- Control (1)
- Cooperative intelligent transport system (1)
- Correlation (math, stat) (1)
- Crash helmet (1)
- Crashtest (1)
- Crossing the road (pedestrian) (1)
- Cycle car (1)
- Data bank (1)
- Data security (1)
- Datensicherheit (1)
- Dauerhaftigkeit (1)
- Daylight (1)
- Daytime running light (1)
- Deceleration (1)
- Decke (Straße) (1)
- Deckschicht (1)
- Deformable barrier (Impact test) (1)
- Deformable barrier system (impact test) (1)
- Dehnungsmessstreifen (1)
- Demand (econ) (1)
- Demographie (1)
- Deutschland ; Konferenz (1)
- Diesel engine (1)
- Dieselmotor (1)
- Digital model (1)
- Dimension (1)
- Disabled person (1)
- Distribution (gen) (1)
- Driver experience (1)
- Driving aptitude (1)
- Durability (1)
- Durchsichtigkeit (1)
- Dynamo (1)
- Eichung (1)
- Eigenschaft (1)
- Einstellung (psychol) (1)
- Electronic stability program (1)
- Elektronisches Stabilitätsprogramm (1)
- Emission (1)
- Emission control (1)
- Emissionskontrolle (1)
- Engine capacity (1)
- Environment (1)
- Environment protection (1)
- Erfahrung (menschl) (1)
- Erste Hilfe (1)
- Erwachsener (1)
- European New Car Assessment Programme (1)
- Experience (human) (1)
- Experimental road (1)
- Expert system (1)
- Expertensystem (1)
- Fahrassistenzsystem (1)
- Fahrbahn (1)
- Fahrbahnüberquerung (1)
- Fahrbare Barriere (1)
- Fahrstreifen (1)
- Fahrstreifenwechsel (1)
- Fahrtauglichkeit (1)
- Fahrwerk (1)
- Fahrzeugabstand (1)
- Fahrzeugachse (1)
- Fahrzeugbeleuchtung (1)
- Fahrzeugteile (1)
- Failure (1)
- Farbe (1)
- Feuer (1)
- Finite element method (1)
- Fire (1)
- First aid (1)
- Force (1)
- Form (1)
- Four wheel drive (1)
- Fracht (1)
- Frau (1)
- Freight (1)
- Front (1)
- Fuel consumption (1)
- Future transport mode (1)
- Gebiet (1)
- Geländefahrzeug (1)
- Gestaltung (1)
- Grenzwert (1)
- Gussasphalt (1)
- Haftung (jur) (1)
- Halogen (1)
- Halogene (1)
- Harmonization (1)
- Hazard (1)
- Head (human) (1)
- Height (1)
- Hell (1)
- Hinten (1)
- Hubraum (1)
- Höhe (1)
- Hüfte (menschl) (1)
- In Bewegung (1)
- In service behaviour (1)
- In situ (1)
- Intelligent transport system (1)
- Intelligentes Verkehrssystem (1)
- Intersection (1)
- Interview (1)
- Italien (1)
- Italy (1)
- Itinerary (1)
- Japan (1)
- Kamera (1)
- Kleintransporter (1)
- Kleinwagen (1)
- Knotenpunkt (1)
- Kompatiblität (1)
- Kontakt Reifen Straße (1)
- Kooperatives System (ITS) (1)
- Kopf (menschl) (1)
- Korrelation (math, stat) (1)
- Kraft (1)
- Kraftstoffverbrauch (1)
- Körperstellung (1)
- Lane changing (1)
- Layout (1)
- Liability (1)
- Lichtstärke (1)
- Lieferfahrzeug (1)
- Light (colour) (1)
- Light intensity (1)
- Limit (1)
- Location (1)
- Lochstreifen (1)
- Market (1)
- Markt (1)
- Material (constr) (1)
- Mensch Maschine Verhältnis (1)
- Methode der finiten Elemente (1)
- Mobile barrier (1)
- Mobility (1)
- Mobilität (1)
- Motorhaube (1)
- Motorway (1)
- Moving (1)
- Nachfrage (1)
- Nachhaltigkeit (1)
- Naturalistic Driving (1)
- Naturalistic driving (1)
- Numerisches Modell (1)
- Oberfläche (1)
- On the spot accident investigation (1)
- Optimum (1)
- Optische Anzeige (1)
- Organisation (1)
- Organization (1)
- Ort (Position) (1)
- Overlapping (1)
- Overturning (veh) (1)
- Pelvis (1)
- Pfahl (1)
- Pile (1)
- Population (1)
- Posture (1)
- Properties (1)
- Prüefverfahren (1)
- Public relations (1)
- Public transport (1)
- Punched tape (1)
- Quality assurance (1)
- Qualitätssicherung (1)
- Radial (1)
- Reaction (human) (1)
- Reaktionsverhalten (1)
- Rear (1)
- Region (1)
- Reibungsbeiwert (1)
- Reiseweg (1)
- Research report (1)
- Retread tyre (1)
- Rippe (menschl) (1)
- Road (1)
- Road traffic (1)
- Robot (1)
- Roboter (1)
- Rolling resistance (1)
- Rollwiderstand (1)
- Runderneuerter Reifen (1)
- Safety fence (1)
- Saftey (1)
- Sample (stat) (1)
- Schall (1)
- Schulter (1)
- Schutzeinrichtung (1)
- Schutzhelm (1)
- Schweregrad (unfall (1)
- Schweregrad /Unfall (1)
- Schwingung (1)
- Seite (1)
- Shape (1)
- Shoulder (human) (1)
- Side (1)
- Side light (1)
- Social factors (1)
- Sound (1)
- Soziale Faktoren (1)
- Sport utility vehicle (1)
- Stability (1)
- Stadardization (1)
- Stadt (1)
- Stand der Technik (Bericht) (1)
- Standfestigkeit (1)
- State of the art report (1)
- Steuerung (1)
- Stichprobe (1)
- Stoßstange (1)
- Strain gauge (1)
- Surface (1)
- Surfacing (1)
- Sustainability (1)
- Tagesfahrlicht (1)
- Tageslicht (1)
- Technische Vorschriften (1)
- Technische Überwachung (1)
- Technische Überwachung (Fahrzeug) (1)
- Teenage driver (1)
- Telecommunication (1)
- Telekommunikation (1)
- Telematics (1)
- Telematik (1)
- Temperatur (1)
- Temperature (1)
- Tests (1)
- Toter Winkel (1)
- Toxicity (1)
- Toxizität (1)
- Traffic (1)
- Traffic control (1)
- Traffic lanes (1)
- Traffic motivation (1)
- Traffic regulation (1)
- Traffic regulations (1)
- Traffic sign (1)
- Traffic survey (1)
- Trailer (1)
- Train (1)
- Transparent (1)
- Transport infrastructure (1)
- Trend (stat) (1)
- Typenzulassung (1)
- USA (1)
- Umwelt (1)
- Umweltschutz (1)
- Underride prevention (1)
- Unfalldaten (1)
- Unfallneigung (1)
- Unfallverhuetung (1)
- United Kingdom (1)
- Unterleib (1)
- Untersuchung am Unfallort (1)
- Urban area (1)
- Vehicle Regulations (1)
- Vehicle lighting (1)
- Vehicle spacing (1)
- Veraenderung (1)
- Vereinigtes Königreich (1)
- Verhalten (1)
- Verkehr (1)
- Verkehrsinfrastruktur (1)
- Verkehrsmotivation (1)
- Verkehrssteuerung (1)
- Verkehrsuntersuchung (1)
- Verkehrszeichen (1)
- Versuchsstrecke (1)
- Verteilung (allg) (1)
- Verzögerung (1)
- Vibration (1)
- Video camera (1)
- Vierradantrieb (1)
- Vorne (1)
- Warnung (1)
- Wearing course (1)
- Winkel (1)
- Wirksamkeitsuntersuchung (1)
- Wirkungsanalyse (1)
- Woman (1)
- Zug (Eisenbahn) (1)
- Zukünftiges Verkehrsmittel (1)
- Zusammendrückung (1)
- verletzung) (1)
- Öffentlicher Verkehr (1)
- Öffentlichkeitsarbeit (1)
- Überdeckung (1)
- Überschlagen (1)
Beschrieben wird die Evaluierung eines Testverfahrens der Arbeitsgruppe 10 des European Experimental Vehicle Committee, mit dem die "Fußgängerverträglichkeit" von Frontflächen von Personenkraftwagen bestimmt werden kann. Dabei werden verschiedene Anprallarten von Fußgängern an Fahrzeugen simuliert: der Anprall eines Beines an den Stoßfänger, der Anprall des Oberschenkels an die Vorderkante der Fronthaube und der Anprall des Kopfes auf die Fronthaube. Im Beitrag wird auf die Durchführung von Tests zum Oberschenkelanprall und zum Beinanprall an drei verschiedenen Fahrzeugtypen eingegangen. Beschrieben werden Testverfahren, Versuchsaufbau und Versuchsdurchführung. Die Versuchsreihe zeigte, dass das entwickelte Testverfahren praktikabel ist.
Nach einer Reisebusunfallserie im Jahre 1992 wurde die Bundesanstalt für Straßenwesen beauftragt ein Expertengespräch durchzuführen und eine Projektgruppe einzurichten, um Schwachstellen im Sicherheitssystem des Reisebusverkehrs aufzudecken, Verbesserungsvorschläge zu erarbeiten und den Forschungsbedarf zu identifizieren. Der Beitrag befasst sich schwerpunktmäßig mit den ökonomischen Rahmenbedingungen und der Sicherheit, den Ausbildungs- und Eignungsfragen der Busfahrer, deren Belastung und Beanspruchung, der Einhaltung und Kontrolle von Vorschriften, der Erhöhung der kraftfahrzeugtechnischen Sicherheit sowie dem Notfall- und Unfallmanagement. Zur Weiterentwicklung des Sicherheitssystems wird eine auf breite Mitwirkung auch von Beteiligten angelegte Sicherheitsforschung für den Wirtschaftsverkehr empfohlen. Aus den untersuchten Feldern werden Empfehlungen abgeleitet und der notwendige Forschungsbedarf aufgeführt.
Künftig sollen in Kfz-Scheinwerfern anstelle von Glühlampen auch Gasentladungslampen eingesetzt werden können. Hierbei handelt es sich um Hochdruckentladungslampen, die sich von bisher eingesetzten Halogen-Glühlampen durch die spektrale Verteilung ihres Lichtes, eine höhere Leuchtdichte und einen größeren Lichtstrom - bei geringerer elektrischer Aufnahmeleistung - unterscheiden. Derzeit werden Lampen unter der Bezeichnung D 1 in ein deutsches Fahrzeug der gehobenen Klasse eingebaut. Im Rahmen einer Vorstudie innerhalb des Projektes wurden die folgenden Punkte untersucht: - Integrierbarkeit der Lampe und des Scheinwerfers in bestehende Regelungen; - lichttechnische Eigenschaften der Gasentladungssysteme wie Zünd- und Anlaufverhalten in unterschiedlichen Betriebszuständen; - Farbwiedergabe retroreflektierender Verkehrszeichen und Signaleinrichtungen; - Leuchtdichtekontraste bei retroreflektierenden Materialien und Rückstrahlern; - Sicherheitsaspekte; - Blendung des Gegen- und des vorausfahrenden Verkehr. In der anschließenden Hauptstudie wurden Vorwärtsreflexion an Fahrbahnoberflächen zur Bestimmung der indirekten Blendung im trockenen und nassen Zustand; - spektrale Reflexion von Fahrbahndecken; - Streuleuchtdichten vor dem Fahrzeug bei Schlechtwettersituationen; - Blendungsunterschiede zwischen konventionellen und Gasentladungs-Systemen; - Gradient der Hell-Dunkel-Grenze untersucht. Bei der Untersuchung der Vorwärtsreflexion zeigte sich, dass sich bei nassen Fahrbahnoberflächen das Maximum der Reflexion in Fahrtrichtung verschiebt. In Schlechtwettersituationen wurde durch den größeren Lichtstrom ein Anstieg der Streuleuchtdichte gemessen. Aus diesem Grunde scheint eine Begrenzung der Vorfeldbeleuchtungsstärke sinnvoll. Aufgrund der Fahrzeugdynamik ergeben sich verschiedene Gradienten der Hell-Dunkel-Grenzen. Sie sind abhängig vom Fahrzeugtyp sowie von der Ausstattung der Fahrzeuge mit Niveauregulierung und automatischer Leuchtweitenregelung. Es ergab sich bei Verwendung von Gasentladungssystemen eine Erhöhung der Blendung. Die Blendbeleuchtungsstärken lagen dabei höher als bei vergleichbaren Halogensystemen. Ebenso wird durch die Vorwärtsreflexion auf der Fahrbahnoberfläche eine erhöhte Blendbeleuchtungsstärke bewirkt. Es zeigte sich, dass insbesondere zur Ermittlung der Beeinflussung älterer Verkehrsteilnehmer durch Gasentladungslampen weitere Untersuchungen erforderlich sind.
In Form einer Pilotstudie wurden eine Literaturrecherche, eine Befragung von Experten der Automobilindustrie und theoretische Untersuchungen zur Frage der Head-Up-Display-Technik (HUD) im Kraftfahrzeug durchgeführt. Auf der Suche nach neuen, die Sicherheit des Kraftfahrzeugverkehrs fördernden Anzeigen findet das HUD zunehmend Interesse. Das Prinzip des HUD im Kraftfahrzeug besteht darin, dass die Informationen des Displays über den in die Windschutzscheibe integrierten Combiner in die Verkehrsszene als virtuelles Bild eingeblendet werden. In Europa wurden von Automobil- und Zulieferfirmen ca. ein Dutzend HUD-Systeme als Experimentalsysteme entwickelt. In den europäischen Forschungsprogrammen PROMETHEUS und DRIVE wird das HUD als eine von mehreren neuen Anzeigetechniken untersucht. In den USA und Japan befinden sich HUD-Systeme in Serienfahrzeugen bereits seit einigen Jahren auf dem Markt. Informationen auf einem HUD im Kraftfahrzeug werden schneller und sicherer abgelesen, als auf der konventionellen Instrumententafel. Insbesondere die physiologischen Anteile des Wahrnehmungsvorganges, das heißt die Augenbewegung, das Akkommodieren und das Adaptieren, erfolgen mit einem HUD schneller. Allerdings kann die Verquickung der Verkehrsszene mit bordeigenen Informationen zu verändertem Fahrverhalten und zu anderen Beobachtungsstrategien der Kraftfahrer führen. Die HUD-Technik ist zwar relativ fortgeschritten, jedoch liegen nur wenige fundierte experimentelle Ergebnisse vor. Es wurde daher eine Untersuchungsreihe mit Labor-, Simulator- und Feldexperimenten entworfen, die offene Fragen zu Nutzen, Informationsinhalten und Gestaltung von HUD-Anzeigen beantworten sollen. Gesetzliche Vorschriften der StVZO und die sie tangierenden EG-Richtlinien beziehungsweise ECE-Regelungen legen die Mindestanforderungen an die Sicht aus Kraftfahrzeugen fest, und es bestehen Vorgaben sowohl für die mögliche Position der HUD-Anzeigen, als auch für die Transmission und für die Farberkennung der Verkehrsobjekte.
Die Schwingungsdämpfer von Pkw werden in Deutschland bei der regelmäßigen technischen Überwachung im Rahmen der Hauptuntersuchung nach Paragraph 29 StVZO überprüft. In eingebautem Zustand werden sie dabei im wesentlichen nur einer Sichtkontrolle unterzogen, bei der die Dichtigkeit der Dämpfer und ihre äußerliche Unversehrtheit beurteilt werden. Ziel der Untersuchung war die Klärung der Frage, ob die Notwendigkeit einer aussagekräftigeren Kontrolle der Schwingungsdämpfer bei der regelmäßigen technischen Überwachung von Kraftfahrzeugen besteht, da die objektive Messung der Dämpferleistung problematisch ist und der Nutzen einer solchen Maßnahme bisher nicht quantifiziert werden kann. Objektive Prüfergebnisse an Schwingungsdämpfern sind jedoch nur in ausgebautem Zustand zu erhalten. Durch die Untersuchung sollte über eine "Ist-Zustands-Prüfung" von im Verkehr befindlichen Pkw und eine darauf aufbauende Hochrechnung der Anteil der Fahrzeuge, die mit defekten Dämpfern fahren, festgestellt werden. Die Auswertung der Reihenuntersuchung ergab, dass von 5.749 untersuchten Pkw 450 Pkw eine Fahrwerksbeurteilung erhielten, nach der an mindestens einem Rad der prüfstandspezifische Grenzwert nicht eingehalten wurde, was in der Regel auf einen defekten Dämpfer zurückzuführen ist. Dies entspricht hochgerechnet einem Anteil von 7,8 Prozent der zugelassenen Pkw. Folgt man den durch die Reihenuntersuchung ermittelten Ergebnissen und den bisher diskutierten Grenzwerten von 50 Prozent für die Restwirkung der Dämpfer, so würde die Einführung einer obligatorischen Dämpferprüfung zu erheblichen Kosten führen, deren Nutzen jedoch aufgrund fehlender Angaben derzeit nicht festgestellt werden kann. In Anbetracht der Unsicherheiten bezüglich des Einflusses defekter Schwingungsdämpfer auf das Unfallgeschehen und der ermittelten Defektrate konnte die Einführung einer obligatorischen Prüfung auf einem Prüfstand im Rahmen der regelmäßigen Hauptuntersuchung nicht abschließend bewertet werden.
In der Europäischen Gemeinschaft werden derzeit jährlich ca. 50.000 Menschen bei Verkehrsunfällen getötet, ca. 10.000 davon als Fußgänger. Von den 10.600 (1992) in der Bundesrepublik Deutschland bei Straßenverkehrsunfällen Getöteten waren 1.800 Fußgänger (etwa 17 Prozent). Problemgruppen bei Fußgängerunfällen bilden die Kinder wegen ihrer hohen Unfallhäufigkeit und alte Personen wegen ihrer hohen Unfallschwere. Kopfverletzungen sind die häufigste Todesursache bei Fußgängerunfällen. Eine Verringerung der Unfallschwere kann - außer durch Verminderung von Fahr- beziehungsweise Aufprallgeschwindigkeiten der Fahrzeuge - nur durch konstruktive Eingriffe an der vorderen Fahrzeugaußenkontur oder dem Unterbau von Pkw erfolgen. Dazu ist es notwendig, einheitliche Prüfverfahren für die Beurteilung der "Fahrzeugaggressivität" gegenüber Fußgängern bereitzustellen. Die Ableitung eines Prüfvorschlages zur Simulation des Kopfaufpralls auf Fronthauben von Pkw beim Fußgängerunfall, unterteilt in Kopfaufpralltests für Erwachsene und Kinder, ist Gegenstand dieser Arbeit. Es werden, ausgehend von einer Analyse der Unfallstatistik, der Entstehungsmechanismus von Kopfverletzungen erklärt, die für ein Prüfverfahren notwendigen Eingangsparameter (Masse, Geschwindigkeit, Aufprallstellen am Fahrzeug etc.) abgeleitet und die Ergebnisse der gewählten Prüfkörpertestmethode mit Ergebnissen von Leichenversuchen verglichen. Eine Kosten-/Nutzen-Betrachtung am Schluss der Arbeit zeigt, dass sich bei nur geringen Kosten ein volkswirtschaftlicher Nutzen durch eine allgemeine Anwendung des Prüfverfahrens mit ca. 270 Millionen DM allein in der Bundesrepublik Deutschland pro Jahr erzielen ließe.
Die vorliegende Studie untersucht die Auswirkung der Ausstattung von Motorrädern mit Anti-Blockier-System (ABS) auf die Fahrsicherheit von Motorrädern. Hierzu wurden Fahrversuche im realen Verkehr und auf abgesperrter Teststrecke durchgeführt. Erfahrene und wenig erfahrene Motorradfahrer absolvierten Testfahrten auf nasser und trockener Fahrbahn mit und ohne ABS-Aktivierung des Motorrades. Bei den Versuchsfahrten kam es zu einigen kritischen Fahrsituationen, bei denen die Versuchspersonen insbesondere zu Beginn des Bremsmanövers von ihrem "normalen" Bremsverhalten abwichen. Bei blockierendem Hinterrad wurde der Bremsdruck vorne und hinten reduziert, was zu einer deutlichen Bremswegverlängerung führte. Bei den Vollbremsungen unter idealen Bedingungen auf abgesperrter Strecke wurden von erfahrenen Fahrern ohne ABS kürzere Bremswege als mit ABS erreicht. Kurvenbremsungen mit ABS-Regelung wurden im mittleren Geschwindigkeits- und Schräglagebereich fahrstabil durchgeführt. Die Ergebnisse zeigen, dass selbst erfahrene Motorradfahrer Bremsweg in kritischen Situationen verschenken. Geeignete Antiblockiersysteme könnten Motorradfahrern die Angst vor Radblockaden nehmen. Dies dürfte einen erheblichen Beitrag zur Steigerung der aktiven Sicherheit leisten.
Wegen der wachsenden Verbreitung von Fahrradanhängern zum Kindertransport und der möglichen Unfallgefährdung ist im vorliegenden Forschungsprojekt deren passive Sicherheit untersucht worden. Zudem wurde der Frage nachgegangen, ob der Transport von Kindern im Fahrradanhänger sicherer ist als mit dem Fahrrad mit Kindersitzen. In Absprache mit Herstellern und Vertreibern wurden verschiedene Untersuchungen durchgeführt. Es handelte sich um Anprallversuche (Anfahrversuche), Rollwagenversuche (Schlittenversuche) sowie Kopffreiheitsprüfungen und Fallversuche. Bei den Versuchen waren die Prüfobjekte mit einem oder zwei Dummies besetzt, die mit Messdatenaufnehmern ausgestattet waren. Verschiedene Messdaten, zum Beispiel Kopf- und Brustbeschleunigung, wurden erfasst und ausgewertet. Zusätzlich wurde das Kopfschutzkriterium (HPC) berechnet und bewertet. Entstandene Schäden an den Prüfobjekten wurden aufgenommen und durch Fotos dokumentiert. Die Versuchsabläufe selbst wurden mit Hochgeschwindigkeitskameras aus verschiedenen Positionen aufgezeichnet. Beim Anfahrversuch mit einem Pkw gegen ein Gespann aus Fahrrad und Anhänger waren direkte Anstöße der Anhängerinsassen an die Pkw-Front zu erkennen. Die Beschleunigungswerte waren dabei relativ hoch. Anstöße gegen Anhängerinnenteile waren bei fast allen Versuchen zu beobachten. Teilweise wurden Radaufhängungen und Radnaben beschädigt. Durch die Rollwagenversuche wurden konstruktive Schwächen bei den Sitzen und Rückhaltesystemen festgestellt. Nähte, Befestigungen und Verstellösen wurden zerstört. Es stellte sich heraus, dass die Qualität des Gurtsystems, die Steifigkeit des Anhängeraufbaus, die Sitzposition der Kinder und die vorhandene Kopffreiheit ausschlaggebend für das Verletzungsrisiko der Insassen sind. Bei den Versuchen mit Fahrradsitzen ergaben sich hohe Beschleunigungswerte durch den direkten Kontakt des Radfahrers mit der Fahrzeugfront und/oder der Fahrbahn. Das Gewicht des Radfahrers, des Fahrrades und auch Fahrradteile bergen ein erhöhtes Verletzungsrisiko für das Kind. Zusätzlich besteht die Gefahr überfahren zu werden, wenn das Kind nach dem Sturz des Fahrrades ungeschützt auf der Fahrbahn liegt. Ein direkter Vergleich der beiden Transportmöglichkeiten war aufgrund der geringen Daten der Versuche mit Fahrradkindersitzen nur bedingt möglich. Tendenziell ist der Transport der Kinder im Fahrradanhänger als weniger gefährlich zu bewerten. Es werden die Vor- und Nachteile dargestellt. Zur Bewertung der Sicherheit von Fahrradanhängern wurden die folgenden Prüfmethoden erarbeitet: - Pendelschlagprüfung für die gesamte Chassisstruktur; - Kopffreiheitsprüfung; - Belastungsprüfung der Aufbaustruktur; - Festigkeitsprüfung der Gurtsysteme. Die Prüfungen sind so aufgebaut, dass sie mit einfachen Mitteln durchzuführen sind. Es sollte somit jedem Anhängerhersteller möglich sein, die passive Sicherheit seiner Produkte umfassend zu untersuchen. Die Prüfverfahren für die Sicherheitsbewertung sollen in eine DIN-Norm und in das Merkblatt für Fahrradanhänger einfließen. Der Original-Forschungsbericht enthält einen umfangreichen Fotoband zu den Einzelheiten der Versuche und Versuchsaufbauten sowie zu den Beschädigungen der Prüfobjekte und kann bei der BASt eingesehen werden.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
A means of assessing the passive safety of automobiles is a desirable instrument for legislative bodies, the automobile industry, and the consumer. As opposed to the dominating motor vehicle assessment criteria, such as engine power, spaciousness, aerodynamics and consumption, there are no clear and generally accepted criteria for assessing the passive safety of cars. The proposed method of assessment combines the results of experimental safety tests, carried out according to existing legally prescribed or currently discussed testing conditions, and a biomechanical validation of the loading values determined in the test. This evaluation is carried out with the aid of risk functions which are specified for individual parts of the body by correlating the results of accident analysis with those obtained by computer simulation. The degree of conformance to the respective protection criterion thus deduced is then weighted with factors which take into account the frequency of occurrence and the severity of the accident on the basis of resulting costs. Each of the test series includes at least two frontal and one lateral crash test against a deformable barrier. The computer-aided analysis and evaluation of the simulation results enables a vehicle-specific overall safety index as well as partial and individual safety values to be determined and plotted graphically. The passive safety provided by the respective vehicle under test can be defined for specific seating positions, special types of accident, or for individual endangered parts of the body.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
This paper provides an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two years. The progress of five working packages of this research project is presented: Literature review, Accident analysis, Structural survey of cars, Crash testing, and Mathematical modelling. According to the planned time schedule the progress of research work is different for the five working packages.
Der Autor berichtet über zwei Forschungsprojekte zur Prüfung von runderneuerten Reifen durch Schnell- und Dauerlaufprüfung. Es wurden Pkw- und Lkw-Reifen mit Karkassen unterschiedlicher Hersteller und unterschiedlichen Alters mit und ohne reparierte Durchstoßschäden untersucht. Die Versuchsergebnisse spechen für eine Altersbegrenzung der rundzuerneuernden Karkassen auf 6 Jahre. Das Reparieren sollte nur bei der Runderneuerung von Lkw-Reifen toleriert werden. Eine Rückstufung der Geschwindigkeitsklassen nach Runderneuerung von Pkw-Reifen zeigt eine positive Wirkung.
Die Autoren berichten über den Auftaktworkshop "Empfehlung der Europäischen Kommission über On-board-Informations- und -Kommunikationssysteme: Europäischer Grundsatzkatalog zur Mensch-Maschine-Schnittstelle", der am 7.9.2000 in der Bundesanstalt für Straßenwesen stattfand. Die zuständigen Stellen (wie zum Beispiel die Fahrzeug- und Zulieferindustrie) wurden dazu angehalten, die Empfehlungen zu beachten sowie der BASt über Erfahrungen zu berichten. Dazu wurde mit den Teilnehmern ein erster Gedankenaustausch geführt und das gemeinsame Vorgehen abgestimmt.
Die Autoren berichten über den Auftaktworkshop "Empfehlung der Europäischen Kommission über On-board-Informations- und -Kommunikationssysteme: Europäischer Grundsatzkatalog zur Mensch-Maschine-Schnittstelle", der am 7.9.2000 in der Bundesanstalt für Straßenwesen stattfand. Die zuständigen Stellen (wie zum Beispiel die Fahrzeug- und Zulieferindustrie) wurden dazu angehalten, die Empfehlungen zu beachten sowie der BASt über Erfahrungen zu berichten. Dazu wurde mit den Teilnehmern ein erster Gedankenaustausch geführt und das gemeinsame Vorgehen abgestimmt.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
EEVC Status report
(2001)
Erfahrungen in Deutschland mit der Anwendung der EU-Empfehlung "Europäischer Grundsatzkatalog zur Fahrer-Fahrzeug-Schnittstelle für Informations- und Kommunikationssysteme" werden beschrieben und daraus Konsequenzen abgeleitet. Insgesamt ist die ergonomische Bewertung der Mensch-Maschine-Schnittstelle von Fahrerinformations- und -Kommunikationssystemen nicht als einmaliges Ereignis, sondern als immer wieder zu durchlaufender Vorgang anzusehen, da neben neuen wissenschaftlichen Erkenntnissen jeweils neu entwickelte Geräte und Systeme zu berücksichtigen sind, was eine Anpassung der Grundsätze beziehungsweise eine Öffnung der Grundsätze für technische Neuerungen mit hohem Sicherheitsstandard erfordern könnte. Demonstrationen neuartiger Bedienkonzepte, Systementwicklungen und Arbeitstechniken sowie die hierzu durchgeführten Nutzertests verdeutlichen, dass ergonomisch sehr vielversprechende Lösungen (wie zum Beispiel Schnittstellen, die Eingaben mittels Gestik gestatten) existieren, beziehungsweise sich in der Entwicklung befinden. Diese Lösungen zeigen, dass die Empfehlung in weiten Bereichen technologieabhängig, das heißt, mit Blick auf Neuentwicklungen, nicht erschöpfend ist. Die Weiterentwicklung der Grundsätze sowie die Bewertung der sicheren Gestaltung der Mensch-Maschine-Schnittstelle bedarf nicht nur einer europaweit, sondern weltweit abgestimmten Vorgehensweise.
Es wird über das Ende 2002 abgeschlossene EU-Projekt ADVISORS berichtet. Ziel dieses Projektes, an dem sich 16 Organisationen aus 10 europäischen Ländern beteiligten, war es, die Entwicklung, Testung und Implementierung von Fahrerassistenzsystemen (FAS) zu unterstützen. Es wurde eine umfassende Methodik zur Bewertung von FAS entwickelt und auf dieser Basis wurden eine Reihe von Evaluationsstudien zu ausgewählten FAS durchgeführt. Des Weiteren wurden Implementierungsstrategien für bestimmte FAS entwickelt und mit Experten verschiedener Länder diskutiert.
The development of tyre- and truck-manufacturers leads to the direction to introduce wide base single tyres (size 495/45R22,5) instead of twin tyres on the driving axle of trucks, tractors and busses. To study the driving behaviour and safety of various trucks and units with different tyre combinations and loading conditions was the aim of the study. A computer-aided simulation was used for this investigation. Drive tests with a 40 t unit with prototype single tyres on the drive axle were carried out to verify the simulation. Alterations in driving behaviour and driving safety are mainly dependent on the tyre cornering stiffness. The prototype wide single tyres had a higher lateral stiffness which leads to a higher degree of under-steering (safer driving behaviour). The altered spring base on the drive axle had no influence on the side- tilt stability of vehicle combinations but the solo truck profited from the higher rear axle roll stiffness (less danger for roll-over accidents). As far as the driving safety is concerned nothing speaks against wide base tyres on the drive axle. The simulation of a tyre defect in a bend (assuming 40% of the max. transferable side force for the flat tyre) showed no increased danger using wide single tyres. Later driving tests showed however the need of tyre run flat possibilities to avoid jack-knifing of road trains. Also tyre pressure monitoring systems and electronic stability programs for the trucks are advised.
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
Sowohl mit dem 3. Road Safety Action Programme der Europäischen Kommission als auch mit dem deutschen Verkehrssicherheitsprogramm werden die verkehrspolitischen Zielsetzungen zur Erhöhung der Verkehrssicherheit in Europa und Deutschland festgelegt. Hierbei muss die passive Fahrzeugsicherheit auch weiterhin eine bedeutende Rolle übernehmen. Es ist jedoch auch festzustellen, dass durch den zunehmenden Einsatz von Elektronik im Fahrzeug die klassischen Bereiche der aktiven und passiven Fahrzeugsicherheit mehr und mehr ineinander greifen. Der Fortschritt in der Elektronik ermöglicht eine Integration der Systeme der aktiven und passiven Sicherheit. Dadurch lässt sich die Fahrzeugsicherheit weiter steigern. Durch die Vernetzung der Systeme lassen sich sogar Kosten einsparen. Der europäische Regierungsausschuss EEVC (European Enhanced Vehicle-safety Committee), die Verbraucherschutzorganisation Euro NCAP (European New Car Assessment Programme) und die Europäische Kommission mit der eSafety Initiative haben diesen Trend erkannt und entsprechende Aktivitäten eingeleitet.
Der Autor berichtet über das neu eingerichtete Expertennetzwerk HUMANIST, das sich mit Fragen der nutzerorientierten und sicherheitsgerechten Gestaltung von Fahrerassistenz- und Informationssystemen befasst. Ziel sind die Zusammenführung und Integration entsprechender Forschungsaktivitäten auf europäischer Ebene.
Abschluss des deutsch-französischen Verbundprojekts "Inter-Vehicle Hazard Warning" (DEUFRAKO-IVWH)
(2004)
Im Rahmen der Deutsch-Französischen Kooperation im Verbundprojekt "Inter-Vehicle Hazard Warning" (DEUFRAKO-IVWH) wurde ein auf Fahrzeug-Fahrzeug-Kommunikation basierendes Warnsystem konzipiert und bewertet. Die im Rahmen des Projekts durchgeführten Arbeiten haben gezeigt, dass ein auf Fahrzeug-Fahrzeug-Kommunikation basierendes Warnsystem prinzipiell geeignet ist, einen Beitrag zur Erhöhung der Verkehrssicherheit zu leisten. Das Ausmaß der zu erwartenden positiven Effekte ist allerdings ganz wesentlich abhängig vom Ausstattungsgrad der Fahrzeugflotte mit einem solchen System.
Die Gestaltung der Interaktion zwischen den elektronischen "Infotainment"-Systemen im Auto und dem Fahrer gewinnt zunehmend an Bedeutung für die Verkehrssicherheit. Dem positiven Nutzen, den die Systeme hinsichtlich Fahrerunterstützung und Fahrkomfort aufweisen, stehen möglicherweise negative Auswirkungen auf die Fahrsicherheit gegenüber, wenn Ablenkung und Überlastung des Fahrers auftreten. Diesem Problemfeld widmete sich das EU-Projekt "Communication Multimedia Unit Inside Car" (COMMUNICAR), das im Juni 2003 abgeschlossen wurde. Hauptziel des Projekts waren die Entwicklung und Evaluierung eines Systems, das den Fahrer bei der Bewältigung der eingehenden Informationen unterstützt und eine zentrale Bedienmöglichkeit aufweist. Das COMMUNICAR-System enthält folgende wesentliche Elemente: Verschiedene Funktionen zu Telematikdiensten, Unterhaltung und zur digitalen Darstellung der traditionellen Informationen; eine als Informationsmanager (IM) bezeichnete regelbasierte Filterlogik sowie eine multimediale integrierte Mensch-Maschine-Schnittstelle (MMS) zur zentralen Bedienung und Informationsausgabe. In der ersten Phase der Entwicklung wurden die Nutzeranforderungen analysiert, die Funktionen definiert und die Ein-/Ausgabemodalitäten festgelegt. In der zweiten Phase wurden virtuelle Prototypen zur Gestaltung der MMS erarbeitet und diese in den anschließenden Nutzertest im Labor bewertet und ausgewählt. Die dritte Phase diente der Systementwicklung, bei der es vor allem um die Filterlogik des IM ging. Das System wurde zunächst im Fahrsimulator, anschließend unter Feldbedingungen getestet. Die Ergebnisse, die in den wesentlichen Einzelheiten berichtet werden, zeigten insgesamt ein positives Bild sowohl hinsichtlich der subjektiven Akzeptanzbewertung als auch hinsichtlich des Fahrverhaltens.
Topics of this report are: Securing mobility and making mobility sustainable - Strategies for road safety: Safe behavior, Safe vehicles, Safe infrastructure, Telematics, International vehicle-engineering measures " Accident statistics " Accident research " Passive vehicle safety " Active vehicle safety " Driver assistance systems " Environmental protection through vehicle engineering.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
Die Reduzierung des Verkehrslärms ist eine große Herausforderung für alle Beteiligten. Das gilt umso mehr, als nach den Prognosen sich die Verkehrsleistung auf der Straße noch stark erhöhen wird. Viele Stellen in Deutschland, wie Industrie, Forschungseinrichtungen und Behörden haben sich der Problematik angenommen. Forschungsarbeiten wurden und werden durchgeführt oder sind in Vorbereitung. Über die nationalen Aktivitäten hinaus wird das Thema europaweit behandelt. In vier Beiträgen wird über die europäischen Forschungsprojekte SILVIA, ITARI, SILENCE und P2RN berichtet. Das Spektrum der Konzepte dieser Forschungsarbeiten ist sehr breit und erstreckt sich über praktische und theoretische Ansätze.
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 13. Oktober 2006 in Baden-Baden das 6. Symposium "Sicher fahren in Europa". Die Fachvorträge befassten sich mit den Themenbereichen: Ansätze zu mehr Verkehrssicherheit, - Verbesserung der Fahrzeugsicherheit, - Besondere Zielgruppen. Die CD-ROM dokumentiert die Grußworte, die Referate und die Podiumsdiskussion.
Das Projekt IMPROVER (Impact Assessment of Road Safety Measures for Vehicles and Road Equipment / Wirkungsanalyse und Bewertung von verschiedenen Verkehrssicherheitsmaßnahmen) wurde im Auftrag der Europäischen Kommission (Generaldirektion Energie und Verkehr) bearbeitet, um die folgenden Straßenverkehrssicherheitsaspekte zu untersuchen: den Einfluss der wachsenden Zahl von Sport Utility Vehicles (SUV) und Multi Purpose Vehicles (MPV) auf Verkehrssicherheit, Kraftstoffverbrauch und Emissionen; die Bewertung von Maßnahmen zur Verbesserung der Verkehrssicherheit von leichten Nutzfahrzeugen; die Auswirkungen des Tempomaten auf Verkehrssicherheit, Kraftstoffverbrauch und Emissionen; die Harmonisierung von Verkehrszeichen und Markierungen auf dem Transeuropäischen Straßennetz (TERN) unter Verkehrssicherheitsgesichtspunkten. Das Projekt wurde von der Bundesanstalt für Straßenwesen (BASt) zusammen mit 14 Partnerinstituten von November 2004 bis Mai 2006 bearbeitet. Entsprechend den Aufgaben wurde das Projekt in vier voneinander unabhängige Subprojekte eingeteilt. Der vorliegende Artikel gibt eine Übersicht über die in den jeweiligen Unterprojekten geleisteten Arbeiten, deren Ergebnisse und die daraus abgeleiteten Empfehlungen.
As set out in the Terms of Reference, the objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configuration such as impacts with car sides, trucks, and pedestrians. Since 2003, EEVC WG 15 served as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the development of Crash Test Procedures" (VC-COMPAT) project that was finalised at the end of 2006 and partly funded by the European Commission. This paper presents the research work carried out in the VC-COMPAT project and the results of its assessment by EEVC WG 15. Other additional work presented by the UK and French governments and industry " in particular the European industry - was taken into consideration. It also identifies current issues with candidate testing approaches. The candidate test approaches are: - an offset barrier test with the progressive deformable barrier (PDB) face in combination with a full width rigid barrier test - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall supplemented by the forces measured in the offset deformable barrier (ODB) test with the current EEVC barrier. These candidate test approaches must assess the structural interaction and give information of frontal force levels and compartment strength for passenger vehicles. Further, this paper presents the planned route map of EEVC WG 15 for the evaluation of the proposed test procedures and assessment criteria.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
Technical progress in automotive engineering focuses at the moment on two competing branches: improving safety and reducing energy consumption. Recent consideration has been given to a third factor, cost to the consumer. Challenges are presented by demographic changes, especially with increasing participation of elderly people in road traffic. The report considers the recent history of road accidents in Germany and statistics relating to vehicle population and road performance. There is a general trend towards decreasing numbers of accidents and their severity. Transport is responsible for roughly 20% of CO2 emissions and approximately 70% of total petroleum consumption. The Federal Government has responded to these challenges by publishing the Freight Transport and Logistics Masterplan in the summer of 2008. It describes the strategic transport policy direction and the key elements of the future course of action which are to be used to ensure the provision of efficient infrastructure and, at the same time, to reduce the amount of energy consumed by vehicles and make transport more efficient, cleaner and quieter. This document contains a number of concrete measures subsumed under the following six objectives: Making optimum use of transport infrastructure - shaping transport to make it more efficient; Reducing the number of journeys - ensuring mobility; Transferring more traffic to the railways and inland waterways; Upgrading more transport arteries and hubs; Environmentally friendly, climate friendly, quiet and safe transport, and Good working conditions and good training in the freight transport industry. Progress in research is outlined in the following areas: Daytime Running Lights for Motorcycles; Safety of hydrogen vehicles - addressing safety and environmental issues by development of a Global Technical Regulation for hydrogen vehicles; Elements of active vehicle safety for elderly drivers; Periodical Technical Inspection of electronically controlled systems in road vehicles - Electronic Stability Control; Pedestrian protection; Crash Compatibility - role of collision partner in passive safety tests; Child safety; Euro NCAP - Child Restraint Systems, and German Field Operational Test on Car-to-Car and Car-to-Infrastructure Systems (SIM-TD). The research project AKTIV - "Adaptive and Cooperative Technologies for Intelligent Traffic" encompasses the design, development, and evaluation of novel driver assistance systems, knowledge and information technologies and is set up to find solutions for efficient traffic management and Car-to-Car and Car-to-Infrastructure communication for future cooperative vehicle applications. The European Statement of Principles on the Human Machine Interface (HMI), presented at the eSafety Conference, which was held in Berlin on 5/6 June 2007, addresses issues such as Real Time Traffic Information (RTTI), Legal issues of Advanced Driver Assistance Systems (ADAS) and e-security.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
In the EC FP6 Integrated Project Advanced Protection Systems, APROSYS, the first WorldSID small female prototype was developed and evaluated by BASt, FTSS, INRETS, TRL and UPM-INSIA during 2006 and 2007. Results were presented at the ESV 2007 conference (Been et al., 2007). With the prototype dummy scoring a biofidelity rating higher than 6.7 out of 10 according to ISO/TR9790, the results were very promising. Also opportunities for further development were identified by the evaluation group. A revised prototype, Revision1, was subsequently developed in the 2007-2008 period to address comments from the evaluation group. The Revision1 dummy includes changes in the half arms and the suit (anthropometry and arm biomechanics), the thorax and abdomen ribs and sternum (rib durability), the abdomen/lumbar area and the lower legs (mass distribution). Also a two-dimensional chest deflection measurement system was developed to measure deflection in both lateral and anterior-posterior direction to improve oblique thorax loading sensitivity. Two Revision1 prototype dummies have now been evaluated by FTSS, TRL, UPM-INSIA and BASt. The updated prototype dummies were subjected to an extensive matrix of biomechanical tests, such as full body pendulum tests and lateral sled impact tests as specified by Wayne State University, Heidelberg University and Medical College of Wisconsin. The results indicated a significant improvement of dummy biofidelity. The overall dummy biofidelity in the ISO rating system has significantly improved from 6.7 to 7.6 on a scale between 0-10. The small female WorldSID has now obtained the same biofidelity rating as the WorldSID mid size male dummy. Also repeatability improved with respect to the prototype. In conclusion the recommended updates were all executed and all successfully contributed in achieving improved performance of the dummy.
According to the German road traffic regulations children up to the age of 12 or a height below 150 cm have to use approved and appropriate child restraint systems (CRS). CRS must be approved according to UN-ECE Regulation No. 44. The regulation classifies CRS in 5 weight categories. The upper weight group is approved for children from 22 to 36 kg. However, studies show that already today many children weigh more than 36 kg although they have not reached a height of 150 cm. Therefore, no ECE R44 approved CRS is available for these overweight children. In conclusion, today's sizes and weights of children are no longer represented by the current version of the ECE R44. The heaviest used dummy (P10) weighs just 32.6 kg and has a height of 137.9 cm. Statistical data of German children show that already 5% of the children at a height of 137.9 cm have a weight above 45.3 kg. Regarding children at a height of 145 cm, the 95th percentile limit is at a weight of 53.3 kg. Based on these data 4 dummies with different heights and weights were defined and produced. Two of them are overweight. Up to now, there is no experience how current child restraint systems perform in a car crash if they are used by children with a weight above 36 kg and a height smaller than 150 cm. In the future, different child restraint systems will be tested with respect to the ECE R44 regulation using these overweight dummies.
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 15. Oktober 2009 in Baden-Baden ihr 7. Symposium \"Sicher fahren in Europa\". Nach 1991, 1994, 1997, 2000, 2003 und zuletzt 2006 trafen sich auch dieses Mal wieder zahlreiche Fachleute aus Wissenschaft und Politik, Industrie, Wirtschaft und Verbänden aus dem In- und Ausland, trugen neue Forschungsergebnisse vor und erörterten aktuelle Ansätze zur Erhöhung der Verkehrssicherheit. Dabei ging es in den Referaten und Diskussionsbeiträgen und in den vier Workshops vor allem darum, die verkehrspolitischen Entwicklungen und Herausforderungen für die europäische Verkehrssicherheitsarbeit im Hinblick auf folgende Themen zu beleuchten: "Verkehrssicherheit Junger Fahrer", - Das "Auto der Zukunft", - "Demographischer Wandel", - "Landstraßensicherheit". Den Grundsatzreferaten folgten vertiefte Bearbeitungen in den Workshops. Die CD-ROM dokumentiert die Grußworte, Referate und Diskussionsbeiträge.
Mit der EU-Verordnung Nummer 661/2009 zur Typgenehmigung und allgemeinen Sicherheit von Kraftfahrzeugen wird von der EU für schwere Nutzfahrzeuge der Einbau von Spurverlassenswarnsystemen und automatischen Notbremssystemen vorgeschrieben. Mit dem obligatorischen Einbau der Systeme wird eine Reduktion der Abkommens- und Auffahrunfälle von Nutzfahrzeugen aus den Klassen M2, M3, N2 und N3, die auf Grund der hohen Masse der Fahrzeuge folgenschwer sind, erwartet. Als Einführungsdaten werden der 1. November 2013 für neue Fahrzeugtypen und der 1. November 2015 für neue Fahrzeuge genannt. Leistungsanforderungen beziehungsweise technische Spezifikationen, denen die Systeme genügen müssen, liegen jedoch noch nicht vor. Diese werden derzeit von einer Expertengruppe auf UN-ECE-Ebene entwickelt. Dabei wird versucht, technologieneutrale Beschreibungen für die Ausgestaltung der Systeme zu erstellen, die gleichzeitig sowohl den gewünschten Nutzen für die Verkehrssicherheit garantieren, sich aber auch an der derzeit vorhandenen und realisierbaren Technologie orientieren. Darüber hinaus müssen die Systemkosten in einem vernünftigen Verhältnis zum Sicherheitsnutzen stehen. Ziel ist es, im Laufe des Jahres 2011 Vorschläge für die Legislative vorzulegen. Es wird über den Stand der Arbeiten, offene Fragestellungen, Herausforderungen bei der Ausgestaltung der technischen Anforderungen sowie sich abzeichnende Ergebnisse berichtet. Dabei sind die Arbeiten in Bezug auf Lane Departure Warning Systems (LDWS) bereits weiter fortgeschritten als zu Advanced Emergency Braking Systems (AEBS).
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.