91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
Schlagworte
- Anfahrversuch (53) (entfernen)
Institut
- Abteilung Fahrzeugtechnik (39)
- Sonstige (28)
- Abteilung Straßenverkehrstechnik (1)
- Präsident (1)
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
Impact severity is a fundamental measure for all in-depth crash investigation projects. One methodology used in the UK is based on the US Calspan software package CRASH3. The UK- in-depth crash investigation studies routinely use AiDamage3 a software package which is based on an updated version of the original CRASH3 algorithm, including enhancements to the vehicle stiffness coefficients. Real world accident-damaged vehicles are measured and their crush is correlated with a library of stiffness coefficients. These measurements are then used, along with other parameters, to calculate the crash energy and equivalent changes of velocity of the vehicles (delta-v), which is a measure of the impact severity. UK in-depth accident studies routinely validate the crash severity methodologies applied as the vehicle fleet changes. This is achieved by analysing crash test data and using the appropriate residual crush damage and other inputs to AiDamage3 and checking the program- outputs with the known crash severity parameters. This procedure checks, at least in part, the default stiffness values in the data libraries and the reconstruction methods used.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
Streuung von Schutzkriterien in kontrollierten Aufprallversuchen gegen die starre 30 Grad-Barriere
(1983)
Gegenstand der Arbeit ist die Ermittlung von Streubreiten von Fahrzeug- und Dummy-Messwerten in Aufprallversuchen bei Geschwindigkeiten von 50 km/h gegen eine starre 30-°-Barriere. Zu den fahrzeugseitigen Messwerten gehörten die Deformation der Frontstruktur, die maximale Fahrzeugverzögerung, die mittlere Fahrzeugverzögerung und Anforderungen der ECE-Regelung 33. Die gemessenen Standardabweichungen der Einzelwerte lagen mit zwei bis sieben Prozent deutlich unter zehn Prozent. Höhere Standardabweichungen der Messwerte wurden dann beobachtet, wenn Aufpralle nach den Mustern Kopf-Lenkrad (Fahrer), Brust-Lenkrad (Fahrer) und Knie-Armaturentafel (Fahrer und Beifahrer) nicht in allen Versuchen zu beobachten sind. Hohe Streubreiten für die Kopfbeschleunigung bzw. die Beschleunigung der Brust des Dummy auf dem Fahrersitz wurden dadurch verursacht, dass in einem Versuch eine unübliche Vorverlagerung des Dummys infolge mangelhafter Gurtwirkung mit nachfolgendem Brust-Lenkrad-Kontakt zu beobachten war.
Sicherheitstechnische Anforderungen an die Bestuhlung moderner Reisebusse als Rückhaltesysteme
(1991)
Die Schutzfähigkeit von KOM-Fahrgastsitzen, die den ECE-R 80-Anforderungen entsprechen, ist bisher nur für die aufgerichtete Rückenlehne nachgewiesen. Hier wurde untersucht, ob auch geneigte Rückenlehnen ausreichende Schutzwirkung bieten. Ausgehend von der Normalsitzposition verfügen Reisebussitze heutiger Bauart über einen Lehnenverstellwinkel von circa 15 Grad (Normal-, Ruhesitzposition). Sondersitze für Ältere und Sportler erlauben auch die Liegesitz- beziehungsweise Liegeposition bei jedoch erheblich größeren Sitzteilern. In Schlittenaufprallversuchen mit je zwei instrumentierten anthropometrischen Messpuppen auf Reisebus-Doppelsitzen wurden die Belastungsverhältnisse eines frontalen Aufpralls simuliert. Die Lehnenverstelleinrichtung der Prüfsitze wurde behelfsweise so verändert, dass 3 (4) Winkeleinstellungen der Lehnenneigung möglich waren. Für jeweils zwei hintereinander zugeordnete Sitzplätze wurden wechselweise diese Lehneneinstellungen variiert. Mit 17 Doppelsitzen wurden insgesamt 32 Körperaufprallereignisse in den verschiedenen Lehnenneigungskonfigurationen durchgeführt. Die Versuchsergebnisse gliederten sich nach der Bewegungsform des Dummy, seinen Belastungen und den am Vordersitz hervorgerufenen Beschädigungen. Die Aufprallverhältnisse in aufrechter Normalsitzposition entsprechend der ECE-R 80 bildeten die Bewertungsbasis. Die gewonnenen Versuchsergebnisse lassen sich wie folgt zusammenfassen: - Für beliebige Lehneneinstellungen im Winkelbereich bis zu 30 Grad zur Senkrechten bietet die vorgebaute Sitzlehne generell ausreichende Rückhaltewirkung beim Körperaufprall. - Wenn die Vordersitzlehne jedoch steiler eingestellt ist als es der Körperhaltung des dahintersitzenden Dummy entspricht, ist mit 1,5-2fach höheren Kopfbelastungen zu rechnen. Das ECE-R 80-Schutzkriterium HAC < 500 wird überschritten. - Vorsorglich sollte aus sicherheitstechnischer Sicht der zulässige Grenzwinkel der Lehnenneigung auf 30 Grad zur Senkrechten beschränkt werden.
Wegen der wachsenden Verbreitung von Fahrradanhängern zum Kindertransport und der möglichen Unfallgefährdung ist im vorliegenden Forschungsprojekt deren passive Sicherheit untersucht worden. Zudem wurde der Frage nachgegangen, ob der Transport von Kindern im Fahrradanhänger sicherer ist als mit dem Fahrrad mit Kindersitzen. In Absprache mit Herstellern und Vertreibern wurden verschiedene Untersuchungen durchgeführt. Es handelte sich um Anprallversuche (Anfahrversuche), Rollwagenversuche (Schlittenversuche) sowie Kopffreiheitsprüfungen und Fallversuche. Bei den Versuchen waren die Prüfobjekte mit einem oder zwei Dummies besetzt, die mit Messdatenaufnehmern ausgestattet waren. Verschiedene Messdaten, zum Beispiel Kopf- und Brustbeschleunigung, wurden erfasst und ausgewertet. Zusätzlich wurde das Kopfschutzkriterium (HPC) berechnet und bewertet. Entstandene Schäden an den Prüfobjekten wurden aufgenommen und durch Fotos dokumentiert. Die Versuchsabläufe selbst wurden mit Hochgeschwindigkeitskameras aus verschiedenen Positionen aufgezeichnet. Beim Anfahrversuch mit einem Pkw gegen ein Gespann aus Fahrrad und Anhänger waren direkte Anstöße der Anhängerinsassen an die Pkw-Front zu erkennen. Die Beschleunigungswerte waren dabei relativ hoch. Anstöße gegen Anhängerinnenteile waren bei fast allen Versuchen zu beobachten. Teilweise wurden Radaufhängungen und Radnaben beschädigt. Durch die Rollwagenversuche wurden konstruktive Schwächen bei den Sitzen und Rückhaltesystemen festgestellt. Nähte, Befestigungen und Verstellösen wurden zerstört. Es stellte sich heraus, dass die Qualität des Gurtsystems, die Steifigkeit des Anhängeraufbaus, die Sitzposition der Kinder und die vorhandene Kopffreiheit ausschlaggebend für das Verletzungsrisiko der Insassen sind. Bei den Versuchen mit Fahrradsitzen ergaben sich hohe Beschleunigungswerte durch den direkten Kontakt des Radfahrers mit der Fahrzeugfront und/oder der Fahrbahn. Das Gewicht des Radfahrers, des Fahrrades und auch Fahrradteile bergen ein erhöhtes Verletzungsrisiko für das Kind. Zusätzlich besteht die Gefahr überfahren zu werden, wenn das Kind nach dem Sturz des Fahrrades ungeschützt auf der Fahrbahn liegt. Ein direkter Vergleich der beiden Transportmöglichkeiten war aufgrund der geringen Daten der Versuche mit Fahrradkindersitzen nur bedingt möglich. Tendenziell ist der Transport der Kinder im Fahrradanhänger als weniger gefährlich zu bewerten. Es werden die Vor- und Nachteile dargestellt. Zur Bewertung der Sicherheit von Fahrradanhängern wurden die folgenden Prüfmethoden erarbeitet: - Pendelschlagprüfung für die gesamte Chassisstruktur; - Kopffreiheitsprüfung; - Belastungsprüfung der Aufbaustruktur; - Festigkeitsprüfung der Gurtsysteme. Die Prüfungen sind so aufgebaut, dass sie mit einfachen Mitteln durchzuführen sind. Es sollte somit jedem Anhängerhersteller möglich sein, die passive Sicherheit seiner Produkte umfassend zu untersuchen. Die Prüfverfahren für die Sicherheitsbewertung sollen in eine DIN-Norm und in das Merkblatt für Fahrradanhänger einfließen. Der Original-Forschungsbericht enthält einen umfangreichen Fotoband zu den Einzelheiten der Versuche und Versuchsaufbauten sowie zu den Beschädigungen der Prüfobjekte und kann bei der BASt eingesehen werden.
Neben der zunehmenden Bedeutung der aktiven Sicherheit bleiben Maßnahmen der passiven Sicherheit bei der Entwicklung moderner Kraftfahrzeuge unabdingbar. Die Weiterentwicklung von Maßnahmen zum passiven Fußgängerschutz war zunächst größtenteils durch Verbraucherschutztests wie zum Beispiel Euro NCAP oder JNCAP getrieben und ist nun auch durch gesetzliche Regelungen verpflichtend geworden. Im vorangegangenen Forschungsprojekt der BASt FE 82.229/2002 Schutz von Fußgängern beim Scheibenaufprall ist die Grundlage eines modularen Prüfverfahrens für den Kopfaufprall im Bereich der Windschutzscheibe, bestehend aus einem Versuchs- und einem Simulationsteil, erarbeitet worden. Im Rahmen dieses Projektes wurde ein hybrides Testverfahren bestehend aus Versuch und Simulation ausgearbeitet, das den Bereich der Windschutzscheibe und dabei auch crashaktive Systeme wie Airbags berücksichtigt. Das Testverfahren kombiniert Komponentenversuche mit einem Simulationsteil, in dem Fahrzeug-Fußgänger-Simulationen und lmpaktorsimulationen durchgeführt werden. Zusätzliche Dummyversuche dienten zur Bewertung des Testverfahrens. Alle erarbeiteten virtuellen und realen Testmethoden wurden an einem Referenzfahrzeug (Opel Signum), welches repräsentativ für eine durchschnittliche Mittelklasselimousine steht, durchgeführt. Das Fahrzeug wurde mit einem Airbagsystem ausgerüstet und der Testprozedur mit und ohne diesem System vergleichend unterzogen. Innerhalb dieser Untersuchungen konnte gezeigt werden, dass neue Testmethoden unter Ausnutzung von Simulationen und Komponententests es erlauben, realistischere Versuchsbedingungen unter Berücksichtigung von potenziellen Kopfaufprallpositionen und -zeiten zu definieren. Dabei können sehr gute Übereinstimmungen zwischen Fußgängersimulation und Dummyversuch erreicht werden. Die Randbedingungen für den Kopfaufprall und die Aufprallzeit wurden durch den Einsatz von Fußgängermodellen ermittelt. Weiterhin ermöglichen die Simulationen, zusätzliche Einflussdaten wie Vektoren mit den Kopfaufprallgeschwindigkeiten und -winkeln zu bestimmen.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
To improve vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility aims to improve both the self and partner protection properties of vehicles. Although compatibility has received worldwide attention for many years, no final assessment approach has been defined. Within the Frontal Impact and Compatibility Assessment Research (FIMCAR) project, different frontal impact test procedures (offset deformable barrier [ODB] test as currently used for Economic Commission for Europe [ECE] R94, progressive deformable barrier test as proposed by France for a new ECE regulation, moveable deformable barrier test as discussed worldwide, full-width rigid barrier test as used in Federal Motor Vehicle Safety Standard [FMVSS] 208, and full-width deformable barrier test) were analyzed regarding their potential for future frontal impact legislation. The research activities focused on car-to-car frontal impact accidents based on accident investigations involving newer cars. Test procedures were developed with both a crash test program and numerical simulations. The proposal from FIMCAR is to use a full-width test procedure with a deformable element and compatibility metrics in combination with the current offset test as a frontal impact assessment approach that also addresses compatibility. By adding a full-width test to the current ODB test it is possible to better address the issues of structural misalignment and injuries resulting from high acceleration accidents as observed in the current fleet. The estimated benefit ranges from a 5 to 12 percent reduction of fatalities and serious injuries resulting from frontal impact accidents. By using a deformable element in the full-width test, the test conditions are more representative of real-world situations with respect to acceleration pulse, restraint system triggering time, and deformation pattern of the front structure. The test results are therefore expected to better represent real-world performance of the tested car. Furthermore, the assessment of the structural alignment is more robust than in the rigid wall test.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
Abstract: Für Kinder in Deutschland existiert im Pkw weiterhin ein höheres Risiko, im Straßenverkehr bei einem Unfall schwer verletzt oder getötet zu werden, als es für ungeschützte Verkehrsteilnehmer wie Fahrradfahrer oder Fußgänger besteht. Dies erscheint auf den ersten Blick nicht nachvollziehbar, da der Pkw und die vorgeschriebenen Kindersitze den Kindern eine hohe Sicherheit bieten müssten. Der vorliegende Projektbericht gibt Aufschluss über den aktuellen Stand der Sicherheit von Kindern im Pkw in Deutschland und zeigt Optimierungspotenzial auf. Die Schutzwirkung der Kindersitze hängt von mehreren Faktoren ab. Dabei stehen technische Aspekte, die hier detailliert untersucht wurden, im Vordergrund. Doch vor allem in den letzten Jahren zeigte sich immer wieder in Feldstudien, aber auch in der Unfallanalyse, dass Kinderschutzsysteme (KSS) oftmals nicht nach den Vorgaben installiert wurden. Wenn der Kindersitz und/oder das Kind nicht entsprechend der Bedienungsanleitung gesichert werden, kann sich das Schutzpotenzial der KSS reduzieren und gegen Null gehen. Im schlimmsten Fall stellt eine fehlerhafte Benutzung von KSS eine Gefahr sowohl für das Kind als auch für andere Pkw-Insassen dar. Die Unfallanalyse ergab keine Aussage darüber, ob verschiedene KSS-Modelle zu unterschiedlichen Verletzungsmustern führen, da die Unfallkonstellationen pro KSS-Modell zu verschieden waren. Des Weiteren wurde analysiert, inwieweit heutige Testverfahren mit diesen Konstellationen übereinstimmen. Das Ziel, mit wenigen Verfahren möglichst alle relevanten Unfälle abzubilden, wurde zum Teil ereicht. Zu viele Testverfahren mit unterschiedlichen Bewertungssystemen stellen heutzutage die Endverbraucher vor das Problem, dass nicht klar ist, welches KSS wirklich das beste ist. In der Realität hängt die Schutzwirkung zudem noch wesentlich von der KSS-Pkw-Kombination ab, die nur annähernd durch Versuche überprüft werden kann, da sich eine zu hohe Anzahl von Kombinationsmöglichkeiten ergibt. Anhand von mehr als 100 Versuchen wurde das Schutzpotenzial von verschiedenen aktuellen Kindersitzmodellen untersucht. Dabei wurden immer vermeintlich gute und schlechte KSS gegenübergestellt und unter gleichen Randbedingungen getestet. Ziel dieses Vorgehens war es, anhand der Messergebnisse Maßnahmen zu erkennen, die dem Schutz der Kinder dienlich sind. Zusammenfassend kann gesagt werden, dass prinzipiell für Kinder ein gutes Schutzniveau durch KSS besteht, was aber von KSS zu KSS verschieden sein kann. Die teureren KSS wiesen keine mechanische Zerstörung auf und überstanden alle Tests ohne ernsthafte Beschädigungen. Lediglich das oftmals als Dämpfungsmaterial eingesetzte Polystyrol nahm Energie auf und verformte sich wie vorgesehen plastisch. Bei den "Billig-Kindersitzen" ergab sich leider ein komplett anderes Bild. Sobald die Anforderungen über die der Gesetzgebung hinausgehen, ist immer weniger Schutz für die Kinder vorhanden. Besonders im Seitenaufprall offenbarten sich erhebliche Lücken in der Sicherheit. Dies reichte von mechanischem Versagen mancher Plastikteile bis hin zu konstruktiven Unzulänglichkeiten. Vor allem die Gurtführung muss deutlicher gekennzeichnet und mechanisch verstärkt werden. Trotz des hohen Schutzpotenzials einiger Kindersitze ist das Ende der Entwicklung noch nicht abzusehen. In allen Kindersitzklassen ist es prinzipiell möglich, die Belastungswerte weiter zu reduzieren. Dazu werden am Ende des Berichtes verschiedene Möglichkeiten aufgezeigt. Zum einen ist dies eine optimierte Babyschale, die durch eine Trägheitsbewegung gezielt Energie abbaut und das Baby in eine günstigere Position bringt, in der die Belastungen des Körpers reduziert sind. Zum anderen wird gezeigt, dass durch die feste Anbindung des KSS an den Pkw und die Reduzierung der Rotation um die Y-Achse die Belastungen für Kinder reduziert werden können. Größtes Entwicklungspotenzial bietet dabei das ISOFIX-System. Es ist bekannt, dass ISOFIX die Fehlbedienung des Kindersitzes und die Belastungen der Kinder deutlich reduzieren kann. Trotzdem ist die bisherige Marktdurchdringung von ISOFIX eher gering. Obwohl insgesamt ein positives Fazit gezogen werden kann, darf nicht aufgehört werden, die Kindersicherheit weiter zu verbessern. Denn nicht alle Kindersitze schützen heute gleich gut. Einige genügen lediglich den Gesetzesansprüchen und finden in vielen Fällen durch einen sehr geringen Verkaufspreis Zugang in die Pkw. Durch verschärfte Testbedingungen sollten diese Kindersitze abgeschafft und der Weg für neue und bessere Kinderschutzsysteme frei gemacht werden.
The off-set assessment procedure potentially contributes to the FIMCAR objectives to maintain the compartment strength and to assess load spreading in frontal collisions. Furthermore it provides the opportunity to assess the restraint system performance with different pulses if combined with a full-width assessment procedure in the frontal assessment approach. Originally it was expected that the PDB assessment procedure would be selected for the FIMCAR assessment approach. However, it was not possible to deliver a compatibility metric in time so that the current off-set procedure (ODB as used in UNECE R94) with some minor modifications was proposed for the FIMCAR Assessment Approach. Nevertheless the potential to assess load spreading, which appears not to be possible with any other assessed frontal impact assessment procedure was considered to be still high. Therefore the development work for the PDB assessment procedure did not stop with the decision not to select the PDB procedure. As a result of the decisions to use the current ODB and to further develop the PDB procedure, both are covered within this deliverable. The deliverable describes the off-set test procedure that will be recommended by FIMCAR consortium, this corresponds to the ODB test as it is specified in UN-ECE Regulation 94 (R94), i.e. EEVC deformable element with 40% overlap at a test speed of 56 km/h. In addition to the current R94 requirements, FIMCAR will recommend to introduce some structural requirements which will guarantee sufficiently strong occupant compartments by enforcing the stability of the forward occupant cell. With respect to the PDB assessment procedure a new metric, Digital Derivative in Y direction - DDY, was developed, described, analysed, and compared with other metrics. The DDY metric analyses the deformation gradients laterally across the PDB face. The more even the deformation, the lower the DDY values and the better the metric- result. In order analyse the different metrics, analysis of the existing PDB test results and the results of the performed simulation studies was performed. In addition, an assessment of artificial deformation profiles with the metrics took place. This analysis shows that there are still issues with the DDY metric but it appears that it is possible to solve them with future optimisations. For example the current metric assesses only the area within 60% of the half vehicle width. For vehicles that have the longitudinals further outboard, the metric is not effective. In addition to the metric development, practical issues of the PDB tests such as the definition of a scan procedure for the analysis of the deformation pattern including the validation of the scanning procedure by the analysis of 3 different scans at different locations of the same barrier were addressed. Furthermore the repeatability and reproducibility of the PDB was analysed. The barrier deformation readings seem to be sensitive with respect to the impact accuracy. In total, the deliverable is meant to define the FIMCAR off-set assessment procedure and to be a starting point for further development of the PDB assessment procedure.
Sowohl mit dem 3. Road Safety Action Programme der Europäischen Kommission als auch mit dem deutschen Verkehrssicherheitsprogramm werden die verkehrspolitischen Zielsetzungen zur Erhöhung der Verkehrssicherheit in Europa und Deutschland festgelegt. Hierbei muss die passive Fahrzeugsicherheit auch weiterhin eine bedeutende Rolle übernehmen. Es ist jedoch auch festzustellen, dass durch den zunehmenden Einsatz von Elektronik im Fahrzeug die klassischen Bereiche der aktiven und passiven Fahrzeugsicherheit mehr und mehr ineinander greifen. Der Fortschritt in der Elektronik ermöglicht eine Integration der Systeme der aktiven und passiven Sicherheit. Dadurch lässt sich die Fahrzeugsicherheit weiter steigern. Durch die Vernetzung der Systeme lassen sich sogar Kosten einsparen. Der europäische Regierungsausschuss EEVC (European Enhanced Vehicle-safety Committee), die Verbraucherschutzorganisation Euro NCAP (European New Car Assessment Programme) und die Europäische Kommission mit der eSafety Initiative haben diesen Trend erkannt und entsprechende Aktivitäten eingeleitet.
The objective of this deliverable is to describe the expected influence of the candidate test procedures developed in FIMCAR for frontal impact on other impact types. The other impact types of primary interest are front-to-side impacts, collisions with road restraint systems (e.g. guardrails), and heavy goods vehicle impacts. These collision types were chosen as they involve structures that can be adapted to improve safety. Collisions with vulnerable road users (VRU) were not explicitly investigated in FIMCAR. It is expected that the vehicle structures of interest in FIMCAR can be designed into a VRU friendly shell. Information used for this deliverable comes from simulations and car-to-car crash tests conducted in FIMCAR or review of previous research. Three test configurations (full width, offset, and moving deformable barriers) were the input to the FIMCAR selection process. There are three different types of offset tests and two different full width tests. During the project test procedures could be divided into three groups that provide different influences or outcomes on vehicle designs: 1. The ODB barrier provides a method to assess part of the vehicles energy absorption capabilities and compartment test in one test. 2. The FWRB and FWDB have similar capabilities to control structural alignment, further assess energy absorption capabilities, and promote the improvements in the occupant restraint system for high deceleration impacts. 3. The PDB and MPDB can be used to promote better load spreading in the vehicle structures, in addition to assessing energy absorption and occupant compartment strength in an offset configuration. The consortium selected the ODB and FWDB as the two best candidates for short term application in international rulemaking. The review of how all candidates would affect vehicle performance in other impacts (beside front-to-front vehicle or frontal impacts with fixed obstacles) however is reported in this deliverable to support the benefit analysis reported in FIMCAR. The grouping presented above is used to discuss all five test candidates using similarities between certain tests and thereby simplify the discussion.
This paper provides an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two years. The progress of five working packages of this research project is presented: Literature review, Accident analysis, Structural survey of cars, Crash testing, and Mathematical modelling. According to the planned time schedule the progress of research work is different for the five working packages.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.