Filtern
Erscheinungsjahr
- 2013 (153) (entfernen)
Dokumenttyp
- Konferenzveröffentlichung (82)
- Buch (Monographie) (43)
- Wissenschaftlicher Artikel (21)
- Teil eines Buches (Kapitel) (3)
- Bericht (2)
- Arbeitspapier (2)
Sprache
- Deutsch (77)
- Englisch (75)
- Mehrsprachig (1)
Schlagworte
- Deutschland (104)
- Germany (103)
- Konferenz (55)
- Conference (54)
- Research report (36)
- Forschungsbericht (35)
- Safety (29)
- Sicherheit (29)
- Accident (25)
- Bewertung (24)
A biofidelic flexible pedestrian legform impactor (FlexPLI) has been developed from the year 2000 onwards and evaluated by a technical evaluation group (Flex-TEG) of UN-ECE GRSP. A recently established UN-ECE GRSP Informal Group on GTR9 Phase 2 is aiming at introducing the FlexPLI within world-wide regulations on pedestrian safety (Phase 2 of GTR No. 9 as well as the new UN regulation 127 on pedestrian safety) as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents. Besides, the FlexPLI has already been introduced within JNCAP and is on the Euro NCAP roadmap for 2014. Despite of the biofidelic properties in the knee and tibia sections, several open issues related to the FlexPLI, like the estimation of the cost benefit, the feasibility of vehicle compliance with the threshold values, the robustness of the impactor and of the test results, the comparability between prototype and production level and the finalization of certification corridors still needed to be solved. Furthermore, discussions with stakeholders about a harmonized lower legform to bumper test area are still going on. This paper describes several studies carried out by the Federal Highway Research Institute (BASt) regarding the benefit due to the introduction of the FlexPLI within legislation for type approval, the robustness of test results, the establishment of new assembly certification corridors and a proposal for a harmonized legform to bumper test area. Furthermore, a report on vehicle tests that previously had been carried out with three prototype legforms and were now being repeated using legforms with serial production status, is given. Finally, the paper gives a status report on the ongoing simulation and testing activities with respect to the development and evaluation of an improved test procedure with upper body mass for assessing pedestrian femur injuries.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.
Thoracic injuries are one of the main causes of fatally and severely injured casualties in car crashes. Advances in restraint system technology and airbags may be needed to address this problem; however, the crash test dummies available today for studying these injuries have limitations that prevent them from being able to demonstrate the benefits of such innovations. THORAX-FP7 was a collaborative medium scale project under the European Seventh Framework. It focused on the mitigation and prevention of thoracic injuries through an improved understanding of the thoracic injury mechanisms and the implementation of this understanding in an updated design for the thorax-shoulder complex of the THOR dummy. The updated dummy should enable the design and evaluation of advanced restraint systems for a wide variety (gender, age and size) of car occupants. The hardware development involved five steps: 1) Identification of the dominant thoracic injury types from field data, 2) Specification of biomechanical requirements, 3) Identification of injury parameters and necessary instrumentation, 4) Dummy hardware development and 5) Evaluation of the demonstrator dummy. The activities resulted in the definition of new biofidelity and instrumentation requirements for an updated thorax-shoulder complex. Prototype versions were realised and implemented in three THOR dummies for biomechanical evaluation testing. This paper documents the hardware developments and biomechanical evaluation testing carried out.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
Durch den zukünftig zu erwartenden Anstieg des Radverkehrsanteils am Gesamtverkehrsaufkommen und der Veränderung des Fahrzeugkollektivs sowie der Nutzergruppen durch die Zunahme von Elektrofahrrädern werden die Anforderungen an die Verkehrssicherheit im Radverkehr kontinuierlich steigen. Aus diesem Grund ist in dem vorliegenden Forschungsprojekt unter Berücksichtigung verschiedener Fachdisziplinen untersucht worden, welche Sicherheitskenngrößen im Radverkehr neben den bisher üblich verwendeten Unfallkennwerten geeignet sind, die Verkehrssicherheit zukünftig zu bewerten und darzustellen. Zur Identifikation von "neuen" bzw. zusätzlichen Sicherheitskenngrößen wurde eine Struktur zur Differenzierung von Sicherheitskenngrößen für unterschiedliche Stufen einer Fahrradfahrt von der Quelle bis zum Ziel bzw. einem potenziellen Unfall erstellt. Die Ergebnisse wurden in einem Expertenworkshop vor- und zur Diskussion gestellt und im Nachgang entsprechend der Diskussionsergebnisse überarbeitet und angepasst. Durch Heranziehen von Verkehrs- und Unfalldaten mit Radverkehrsbeteiligung aus abgeschlossenen (Forschungs-)Projekten wird für den verkehrsplanerischen Bereich in Anwendungsbeispielen dargestellt, wie für unterschiedliche Stufen einer Fahrradfahrt durch Kombination von bestehenden Unfallkennwerten und Sicherheitsindikatoren "neue" Sicherheitskenngrößen abgeleitet werden können. Aufgrund eines fehlenden einheitlichen Verkehrssicherheitsverständnisses der unterschiedlichen Fachdisziplinen und der teilweise schwachen empirischen Datengrundlage, konnte keine Grundlage zur Identifikation von interdisziplinären Sicherheitskenngrößen geschaffen werden. Aus diesem Grund beschränken sich die Ergebnisse primär auf den Bereich der Verkehrsplanung. Für zukünftige Untersuchungen wird daher empfohlen, auf Grundlage der vorliegenden Ergebnisse eine Methodik zur interdisziplinären Bewertung der Verkehrssicherheit im Radverkehr zu erarbeiten.
Einfluss der veränderten Verkehrsführung bei Ertüchtigungsmaßnahmen auf die Bauwerksbeanspruchungen
(2013)
Im Rahmen von mehreren vorhergehenden Forschungsprojekten wurden vom Forschungsnehmer Untersuchungen zu den Beanspruchungen von Brückenbauwerken infolge des Straßenverkehrs durchgeführt. Die Ergebnisse dieser Untersuchungen führten zu den neuen Verkehrslastannahmen für Straßenbrücken im Eurocode 1, Teil 2 (in Verbindung mit dem deutschen nationalen Anhang) und den Ziellastniveaus in der Nachrechnungsrichtlinie. Im Ergebnis von Nachrechnungen müssen die Bestandsbrücken ertüchtigt oder neu gebaut werden. Ertüchtigung von Autobahnbrücken heißt Bauen unter Verkehr. Auf den Bestandsbrücken ist eine veränderte Verkehrsführung erforderlich. Mit einer veränderten Verkehrsführung geht aber unter Umständen auch eine Veränderung der Beanspruchungen der Brückenbauwerke infolge dieser "Umnutzung" einher. Ziel des vorliegenden Forschungsprojektes ist es, den Einfluss der veränderten Verkehrsführung bei Ertüchtigungsmaßnahmen auf die Bauwerksbeanspruchungen zu analysieren. Unter Anwendung einer in den vorhergehenden Projekten entwickelten Vorgehensweise werden Simulationsrechnungen durchgeführt, in denen verschiedenen Varianten von Spuranordnungen auf Überbauquerschnitten betrachtet werden. Des Weiteren werden differenzierte Verkehrscharakteristiken, also verschiedene Verkehrsstärken und Verkehrszusammensetzungen, betrachtet. Grundsätzlich werden hierbei Beanspruchungen, also zum Beispiel resultierende Biegemomente oder Auflagerkräfte, betrachtet. Aus diesem Grund müssen die Berechnungen für definierte Tragsysteme durchgeführt werden. Im vorliegenden Projekt wurden hierzu zwei reale Brückenbauwerke betrachtet, die sich im Zuge von Autobahnen in Nordrhein-Westfalen befinden. Erweitert werden die Betrachtungen auf ein zusätzliches "virtuelles" Tragsystem, um ein gewisses Spektrum von Stützweiten und Querschnittsbreiten analysieren zu können. Grundsätzlich zeigt sich im Ergebnis der Untersuchungen, dass Beanspruchungen aus aktuellem Verkehr bei normaler Verkehrsführung durch das Lastmodell LM1 des DIN-Fachberichtes 101 abgedeckt werden. Für Beanspruchungen aus zukünftigem Verkehr ist das neue Lastmodell LM1 des Eurocodes erforderlich. Im Rahmen von Baumaßnahmen wird im Allgemeinen eine 4+0-Verkehrsführung eingerichtet. Hierbei werden bei zweiteiligen Überbauquerschnitten vier Fahrstreifen über einen Querschnitt geleitet. Dies geht einher mit einer Verengung der Fahrspuren. In solchen Fällen ist davon auszugehen, dass es nicht möglich ist, dass Lkw-Überholverkehr stattfinden kann. Dies führt zu einer wesentlichen Verringerung der Beanspruchungen von Brückenbauwerken, da auch in Stausituationen in den zwei Richtungsfahrbahnen keine Lkw-Fahrzeuge nebeneinander stehen können. Für Verkehrszusammensetzungen entsprechend der aus der Nachrechnungsrichtlinie bekannten Verkehrsart "Große Entfernung" (50 % Sattelzugfahrzeuge) ergibt sich daher eine Abdeckung der Beanspruchungen aus Straßenverkehr durch das Lastmodell BK60 der DIN 1072. Für Verkehrszusammensetzungen analog der Verkehrsart "Mittlere Entfernung" reicht das Lastmodell BK30/30 zu Abdeckung aus. Weitere Differenzierungen hinsichtlich der Verkehrsstärke führen hier zu keinen wesentlichen Änderungen der getroffenen Aussagen.
Ziel des Projektes war es, bedingt durch die wachsende Anzahl der im Verkehr befindlichen elektrisch und hybrid-elektrisch betriebenen Fahrzeuge, notwendige Anpassungen der periodisch technischen Überwachung zu erarbeiten. Dazu wurden von verschiedenen Fahrzeugen die relevanten Bauteile des elektrischen Antriebsstrangs identifiziert und deren Ausfallverhalten analysiert. Um die Degradationsauswirkungen einzelner Bauteile und Funktionen auf das gesamte System bestimmen zu können, hat die FSD ein Simulationsmodell erstellt. Die daraus ermittelten Ergebnisse waren Grundlage für die Bestimmung verkehrssicherheits- und umweltkritischer Bauteile sowie deren Funktionen. Diese Modellaussagen wurden mit Realversuchen an Fahrzeugen validiert. Zusätzlich konnten in einem Feldversuch 2.560 Fahrzeuge mit elektrischem Antriebsstrang untersucht werden. Aus diesen Ergebnissen lassen sich Änderungsvorschläge für die Untersuchungen und Vorgaben ableiten. Dafür ist für einen Großteil dieser Untersuchungen die Nutzung von Diagnosedaten eine geeignete Möglichkeit. Die 47. Verordnung zur Änderung straßenverkehrsrechtlicher Vorschriften berücksichtigt bereits an vielen Stellen die neuen Antriebskonzepte. Von daher werden lediglich geringe Anpassungen in der StVZO für -§ 19 und den Beispielkatalog dazu, -§ 29, Anlage VIIIa, Anlage VIIId sowie die HU-Richtlinie vorgeschlagen. Für die Durchführung der Untersuchungspunkte zum HV-System ist die Entwicklung einer Hochvolt-Richtlinie empfehlenswert. Einige wichtige Prüfverfahren lassen sich derzeit technisch noch nicht umsetzen. Dazu sind Änderungen der internationalen Bau- und Betriebsvorschriften notwendig. Diese werden bei der EU/UNECE anzuregen sein. Es besteht über dieses Projekt hinaus weiterhin Forschungsbedarf, um sich intensiv mit diesen Fahrzeugen zu befassen und deren Weiterentwicklung zu beobachten, damit notwendige Auswirkungen auf die PTI rechtzeitig erkannt werden können.