Filtern
Dokumenttyp
Schlagworte
- Shock (14) (entfernen)
Institut
- Abteilung Fahrzeugtechnik (14) (entfernen)
The objective of this deliverable is to describe the expected influence of the candidate test procedures developed in FIMCAR for frontal impact on other impact types. The other impact types of primary interest are front-to-side impacts, collisions with road restraint systems (e.g. guardrails), and heavy goods vehicle impacts. These collision types were chosen as they involve structures that can be adapted to improve safety. Collisions with vulnerable road users (VRU) were not explicitly investigated in FIMCAR. It is expected that the vehicle structures of interest in FIMCAR can be designed into a VRU friendly shell. Information used for this deliverable comes from simulations and car-to-car crash tests conducted in FIMCAR or review of previous research. Three test configurations (full width, offset, and moving deformable barriers) were the input to the FIMCAR selection process. There are three different types of offset tests and two different full width tests. During the project test procedures could be divided into three groups that provide different influences or outcomes on vehicle designs: 1. The ODB barrier provides a method to assess part of the vehicles energy absorption capabilities and compartment test in one test. 2. The FWRB and FWDB have similar capabilities to control structural alignment, further assess energy absorption capabilities, and promote the improvements in the occupant restraint system for high deceleration impacts. 3. The PDB and MPDB can be used to promote better load spreading in the vehicle structures, in addition to assessing energy absorption and occupant compartment strength in an offset configuration. The consortium selected the ODB and FWDB as the two best candidates for short term application in international rulemaking. The review of how all candidates would affect vehicle performance in other impacts (beside front-to-front vehicle or frontal impacts with fixed obstacles) however is reported in this deliverable to support the benefit analysis reported in FIMCAR. The grouping presented above is used to discuss all five test candidates using similarities between certain tests and thereby simplify the discussion.
The off-set assessment procedure potentially contributes to the FIMCAR objectives to maintain the compartment strength and to assess load spreading in frontal collisions. Furthermore it provides the opportunity to assess the restraint system performance with different pulses if combined with a full-width assessment procedure in the frontal assessment approach. Originally it was expected that the PDB assessment procedure would be selected for the FIMCAR assessment approach. However, it was not possible to deliver a compatibility metric in time so that the current off-set procedure (ODB as used in UNECE R94) with some minor modifications was proposed for the FIMCAR Assessment Approach. Nevertheless the potential to assess load spreading, which appears not to be possible with any other assessed frontal impact assessment procedure was considered to be still high. Therefore the development work for the PDB assessment procedure did not stop with the decision not to select the PDB procedure. As a result of the decisions to use the current ODB and to further develop the PDB procedure, both are covered within this deliverable. The deliverable describes the off-set test procedure that will be recommended by FIMCAR consortium, this corresponds to the ODB test as it is specified in UN-ECE Regulation 94 (R94), i.e. EEVC deformable element with 40% overlap at a test speed of 56 km/h. In addition to the current R94 requirements, FIMCAR will recommend to introduce some structural requirements which will guarantee sufficiently strong occupant compartments by enforcing the stability of the forward occupant cell. With respect to the PDB assessment procedure a new metric, Digital Derivative in Y direction - DDY, was developed, described, analysed, and compared with other metrics. The DDY metric analyses the deformation gradients laterally across the PDB face. The more even the deformation, the lower the DDY values and the better the metric- result. In order analyse the different metrics, analysis of the existing PDB test results and the results of the performed simulation studies was performed. In addition, an assessment of artificial deformation profiles with the metrics took place. This analysis shows that there are still issues with the DDY metric but it appears that it is possible to solve them with future optimisations. For example the current metric assesses only the area within 60% of the half vehicle width. For vehicles that have the longitudinals further outboard, the metric is not effective. In addition to the metric development, practical issues of the PDB tests such as the definition of a scan procedure for the analysis of the deformation pattern including the validation of the scanning procedure by the analysis of 3 different scans at different locations of the same barrier were addressed. Furthermore the repeatability and reproducibility of the PDB was analysed. The barrier deformation readings seem to be sensitive with respect to the impact accuracy. In total, the deliverable is meant to define the FIMCAR off-set assessment procedure and to be a starting point for further development of the PDB assessment procedure.
Bei der Untersuchung des Insassenschutzes von Pkw's bei Seitenkollisionen wurden als seitlich auftreffende Fahrzeuge neben Pkw auch unterschiedliche Barrierenformen verwendet. Um die Zahl der Prüfungen im Typgenehmigungsverfahren für neue Pkw-Modelle gering zu halten, wurde von der europäischen Automobilindustrie ein Vorschlag zur Harmonisierung europäischer und amerikanischer Lösungen entwickelt. Es wurden zwei Versuchsserien zur Beurteilung des Quergeschwindigkeitseinflusses mit Fahrzeugen europäischer Größenverhältnisse durchgeführt sowie eine Serie mit einer Versuchskonfiguration, die zur Harmonisierung vorgeschlagen wurde. Die Untersuchungsergebnisse zeigen, dass die Kombination einer mobilen deformierbaren Barriere mit Bewegungsparametern zur Simulation eines Querbewegungseinflusses durch kinematische Umkehrung am gestoßenen Fahrzeug nur zu einem geringen Teil die gleiche Belastung bewirkt, wie bei der Kollision mit zwei bewegten Fahrzeugen.
Die Untersuchung sollte erörtern, ob es empfehlenswert ist, das Testverfahren zum streifenden Anprall eines Motorradhelmes auf die Straßenoberfläche in die ECE-R 22 aufzunehmen. Dazu war zu klären, ob die Testmethode geeignet ist, rotatorische Kräfte auf den Prüfkopf zu erfassen und ob sich aufgrund der Unfallsituationen eine Notwendigkeit für ein solches Testverfahren ergibt. Die Messergebnisse zeigen, dass der Zusammenhang zwischen der verletzungswirksamen Rotationsbeschleunigung und der im Testverfahren gemessenen Tangentialkraft nicht ohne Zweifel belegbar ist. Somit wäre zu fordern, dass statt der Tangentialkraft die Rotationsbeschleunigung als Verletzungskriterium betrachtet wird. Dafür wird jedoch ein sehr hoher Anspruch an die Messtechnik im Labor gestellt. Aus der Sicht der Unfallforschung lässt sich sagen, dass bei derartigen Anprallsituationen, insbesondere bei Anprallgeschwindigkeiten von unter 40 km/h, die sich im Laborversuch realisieren lassen, nur mäßige Kopfverletzungen auftreten (AIS 2 oder geringer). Der hohe Aufwand des Testverfahrens scheint also nicht gerechtfertigt zu sein.