Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (29) (entfernen)
Volltext vorhanden
- nein (29) (entfernen)
Schlagworte
- Safety (29) (entfernen)
Institut
- Abteilung Fahrzeugtechnik (29) (entfernen)
A methodology to derive precision requirements for automatic emergency braking (AEB) test procedures
(2015)
AEB Systems are becoming important to increase traffic safety. Test procedures in testing for consumer information, manufacturer self-certification and technical regulations are used to ensure a certain minimum performance of these systems. Consequently, test robustness, test efficiency and finally test cost become increasingly important. The key driver for testing effort and test costs is the required repeatable accuracy in a test design - the higher the accuracy, the higher effort and test costs. On the other hand, the performance of active safety systems depends on time discretization in the environment perception and other sub-systems: for instance, typical sensors supply information with a cycle time of 50 - 150 ms. Time discretization results in an inherent spread of system performance, even if the test conditions are perfectly equal. The proposed paper shows a methodology to derive requirements for a test setup (e.g. test repeats, use of driving robots, ...) as function of AEB system generation and rating method (e.g. Euro NCAP points awarded, pass/fail, ...). While the methodology itself is applicable to AEB pedestrian and AEB Car-Car scenarios, due to the lack of sufficient test data for AEB Car-Car, the focus of this paper is on AEB pedestrian scenarios. A simulation model for the performance of AEB Pedestrian systems allows for the systematic variation of the discretization time as well as test condition accuracy. This model is calibrated with test results of 4 production vehicles for AEB Pedestrian, all fully tested by BASt according to current Euro NCAP test protocols. Selected parameters to observe the accuracy of the test setup in case of pedestrian AEB is the calculated impact position of pedestrian on the vehicle front (as if no braking would have occurred), and the test vehicle speed accuracy. These variable was shown in real tests to be repeatable in the range of ± 5 cm and ± 0,25 km/h, respectively, with a fully robotized state of the art test setup. The sensitivity of AEB performance (measured in achieved speed reduction as well as overall rating result according to current Euro NCAP rating methods) towards discretization and the sensitivity of performance towards test accuracy then is compared to identify economic yet robust test concepts. These comparisons show that the available repeatability accuracy of current test setups is more than sufficient for today's AEB system capabilities. Time discretization problems dominate the performance spread especially in test scenarios with a limited pedestrian dummy reveal time (e.g. child behind obstruction, running adult scenarios with low car speeds). This would allow to increase test tolerances to decrease test cost. A methodology which allows to derive the required tolerances in active safety tests might be valuable especially for NCAPs of emerging countries that do not have the necessary equipment (e.g. driving robots, positioning units) available for the full-scale and high tolerance EuroNCAP active safety procedures yet still want to rate active safety systems, thus improving the global safety.
Euro NCAP will start to test pedestrian Automatic Emergency Braking Systems (AEB) from 2016 on. Test procedures for these tests had been developed by and discussed between the AsPeCSS project and other initiatives (e.g. the AEB group with Thatcham Research from the UK). This paper gives an overview on the development process from the AsPeCSS side, summarizes the current test and assessment procedures as of March 2015 and shows test and assessment results of five cars that had been tested by BASt for AsPeCSS and the respective manufacturer. The test and assessment methodology seems appropriate to rate the performance of different vehicles. The best test result - still one year ahead of the test implementation - is around 80%, while the worst rating result is around 10%. Other vehicles are between these boundaries.
The EVERSAFE project addressed many safety issues for electric vehicles including the crash and post-crash safety. The project reviewed the market shares of full electric and hybrid vehicles, latest road traffic accident data involving severely damaged electric vehicles in Europe, and identified critical scenarios that may be particular for electric vehicles. Also, recent results from international research on the safety of electric vehicles were included in this paper such as results from performed experimental abuse cell and vehicle crash tests (incl. non-standardized tests with the Mitsubishi i-MiEV and the BMW i3), from discussions in the UN IG REESS and the GTR EVS as well as guidelines (handling procedures) for fire brigades from Germany, Sweden and the United States of America. Potential hazards that might arise from damaged electric vehicles after severe traffic accidents are an emerging issue for modern vehicles and were summarized from the perspective of different national approaches and discussed from the practical view of fire fighters. Recent rescue guidelines were reviewed and used as the basis for a newly developed rescue procedure. The paper gives recommendations in particular towards fire fighters, but also to vehicle manufacturers and first-aiders.
Since the beginning of the testing activities related to passive pedestrian safety, the width of the test area being assessed regarding its protection level for the lower extremities of vulnerable road users has been determined by geometrical measurements at the outer contour of the vehicle. During the past years, the trend of a decreased width of the lower extremity test and assessment area realized by special features of the outer vehicle frontend design could be observed. This study discusses different possibilities for counteracting this development and thus finding a robust definition for this area including all structures with high injury risk for the lower extremities of vulnerable road users in the event of a collision with a motor vehicle. While Euro NCAP is addressing the described problem by defining a test area under consideration of the stiff structures underneath the bumper fascia, a detailed study was carried out on behalf of the European Commission, aiming at a robust, worldwide harmonized definition of the bumper test area for legislation, taking into account the specific requirements of different certification procedures of the contracting parties of the UN/ECE agreements from 1958 and 1998. This paper details the work undertaken by BASt, also serving as a contribution to the TF-BTA of the UN/ECE GRSP, towards a harmonized test area in order to better protect the lower extremities of vulnerable road users. The German In-Depth Accident Database GIDAS is studied with respect to the potential benefit of a revised test area. Several practical options are discussed and applied to actual vehicles, investigating the differences and possible effects. Tests are carried out and the results studied in detail. Finally, a proposal for a feasible definition is given and a suggestion is made for solving possible open issues at angled surfaces due to rotation of the impactor. The study shows that, in principle, there is a need for the entire vehicle width being assessed with regard to the protection potential for lower extremities of vulnerable road users. It gives evidence on the necessity for a robust definition of the lower extremity test area including stiff and thus injurious structures at the vehicle frontend, especially underneath the bumper fascia. The legal definition of the lower extremity test area will shortly be almost harmonized with the robust Euro NCAP requirements, as already endorsed by GRSP, taking into account injurious structures and thus contributing to the enhanced protection of vulnerable road users. After finalization of the development of a torso mass for the flexible pedestrian legform impactor (FlexPLI) it is recommended to consider again the additional benefit of assessing the entire vehicle width.
During the past five years, a Euro NCAP technical working group on pedestrian safety has been working on improving test and assessment procedures for enhanced passive pedestrian safety. After harmonizing the tools and procedures as much as possible with legislation, the work was mainly focused on the development of grid procedures for the pedestrian body regions head, upper leg with pelvis and lower leg with knee. Furthermore, the test parameters for the head and the upper leg were revised, a new lower legform impactor was introduced and the injury thresholds were adjusted or, where necessary, the injury criteria were changed. Finally, the assessment limits and colour scheme were refined, widening the range and adding two more colours in order to provide a more detailed description of the pedestrian safety performance. By abstaining from an assessment based on a worst point selection philosophy, the improved test point determination procedures that were introduced during the years 2013 and 2014 give a more homogeneous, high resolution picture of the pedestrian safety performance of the vehicle frontends. By using a uniform grid for each test zone approximately 200 test points, evenly distributed within each area, can now be assessed per vehicle. The introduction of the flexible pedestrian legform impactor in 2014 enables a more realistic injury prediction of the knee and the tibia using a biofidelic test tool. With the new upper legform test that has been launched in 2015 the assessment in that area is now focusing on the injured body region instead of the injury causing vehicle part and thus is aligned with the approach in the remaining body regions head and lower leg. At the same time, a monitoring test with the headform impactor against the bonnet leading edge is closing the possible gap between the test areas to identify injury causing vehicle parts that moved out of focus due to the introduction of the new upper legform test. The paper describes the new test and assessment procedures with their underlying philosophy and gives an outlook in terms of open issues, specifying the needs for further improvement in the future. In parallel to the work of the pedestrian subgroup, a Euro NCAP working group on heavy vehicles introduced a set of protocol changes in 2011 that were related to the assessment of M1 vehicles derived from commercial vehicles, with a gross vehicle weight between 2.5 and 3.5 tons and 8 or 9 seats. The paper also investigates the applicability of the new pedestrian test and assessment procedures to heavy vehicles.
Per definition, SAE Level 2 (L2) Systems perform both the lateral and longitudinal vehicle motion control with the expectation that the driver completes the Object and Event Detection and Response (OEDR). Since every system performs also parts of the OEDR itself and this amount of OEDR also varies between different L2 systems depending on the intended system design, it cannot be taken for granted that drivers automatically understand their roles and responsibilities in interaction with the system. Especially highly reliable L2 systems performing a greater amount of OEDR while at the same time requiring only little driver input over time can make it difficult for drivers to correctly identify their role and responsibility. Until now, neither application-oriented assessment methods nor design guidelines for OEDR related system design features taking safety of human-machine-interaction into account are available. The objective is therefore to deliver a standardized tool for the assessment of human-machine-interaction-related safety of vehicles with L2 systems currently available on the market. To evaluate the impact of different system design aspects on safety of human-machine-interaction and also to be able to differentiate between system designs, a holistic, standardized and application-oriented assessment procedure is proposed. The novel tablet-based assessment tool focuses not only on available standards and guidelines but measures also concrete user behaviour and user understanding in interaction with the L2 systems. The aim is to gain further insights which cannot be measured directly by simple checklist instruments. For preparation, based on international standards, literature reviews and expert consultations, a first checklistbased expert-evaluation for currently available vehicles with L2 systems was developed. These assessments are focusing on different sources of user information (e.g. user manual), human-machine-interface design as well as the prevention of unintended use by different driver monitoring techniques. The checklist-tool was developed in cooperation with experts of different EuroNCAP test laboratories and validated in a common expert workshop to gain high level of standardization and agreement. However, to assess safety of human-machine-interaction holistically beyond these rather explicit forms of information design criteria, also implicit forms of drivervehicle-communication via vehicle dynamics, functional behavior or reliability play an important role and should be taken into account. Therefore, the main and novel methodological aim is to consider also interaction related processes regarding user´s understanding of roles and responsibilities when applying automated driving functions as well as user´s awareness of automation modes or traffic situations in the modular tablet-based assessment tool.
To assess occupant safety in a crash test, criteria associating the measurements made with a crash test dummy to injury risk are necessary. To enable better protection of elderly car occupants the objective of this study was to develop improved thoracic injury criteria for the THOR average male dummy. The development of these criteria is usually based on matched dummy and Post Mortem Human Surrogate (PMHS) tests by relating the obtained PMHS injuries to dummy measurements. This approach is limited, since only a few tests in relevant loading conditions are available and any new test series requires high efforts to be performed due to their complexity and costs. To overcome these limitations and to extend the dataset for the development of THOR dummy chest injury risk functions a simulation-based approach was applied within the EC funded project SENIORS (Safety Enhanced Innovations For older Road Users - www.seniors-project.eu). Within this study frontal impact sled simulations with an FE model representing a THOR average male dummy and matched simulations with a human body model (HBM) representing an elderly car occupant were carried out. The HBM used for this study was the THUMS TUC with modified rib cage, which was developed in SENIORS. The modifications included material and geometry changes aiming to represent an elderly car occupant. The rib fracture risk was predicted with a deterministic approach whereby a rib was considered broken when the strain exceeded an age-dependent threshold. Furthermore, a probabilistic method was applied to predict the probability of sustaining a certain number of fractured ribs by comparing local strain values to the distribution of cortical rib ultimate strain. By relating the output from the HBM simulations to a multi-point dummy injury criterion, injury risk curves were calculated by statistical methods. The wide range of loading conditions resulted in the desired range of injuries and THOR ATD output. The number of fractured ribs predicted by the HBM based on the deterministic prediction method was between 0 and 15. Furthermore, the probabilistic risk for the number of rib fractures equal or greater than two, three or four was calculated for each load case. The THOR rib deflection criterion Rmax was between 18 and 56 mm, while the PC Score was in the range of 2.5 to 7.2. Based on these outputs new risk curves for the predicted deterministic (AIS2+/3+) and probabilistic injury risk were calculated. The new curves show reasonable shapes and significance that provide trust in their application. The new risk curves are compared to risk curves obtained by traditional methods. The results were found similar to previous injury risk functions based on physical tests, which gives a high level of confidence in the chosen approach. The simulation-based approach of matched ATD model vs. HBM simulation was successfully applied. Rmax curves show a slightly better quality than the injury criterion PC Score.
The levels of continuous vehicle automation have become common knowledge. They facilitate overall understanding of the issue. Yet, continuous vehicle automation described therein does not cover "automated driving" as a whole: Functions intervening temporarily in accident-prone situations can obviously not be classified by means of continuous levels. Continuous automation describes the shift in workload from purely human driven vehicles to full automation. Duties of the driver are assigned to the machine as automation levels rise. Emergency braking, e.g., is obviously discontinuous and intensive automation. It cannot be classified under this regime. The resulting absence of visibility of these important functions cannot satisfy " especially in the light of effect they take on traffic safety. Therefore, in order to reach a full picture of vehicle automation, a comprehensive approach is proposed that can map out different characteristics as "Principle of Operation" at top level. On this basis informing and warning functions as well as functions intervening only temporarily in near-accident situations can be described. To reach a complete picture, levels for the discontinuous, temporarily intervening functions are proposed " meant to be the counterpart of the continuous levels already in place. This results in a detailed and independent classification for accident-prone situations. This finally provides for the visibility these important functions deserve.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschreiben. Das Ergebnis kann indes nicht zufriedenstellen: Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird hier, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschreiben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen. Dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
Für eine Reihe von EU Regelungen im Bereich Fahrzeugsicherheit erlaubt eine Verordnung bereits seit dem Jahr 2010 virtuelles Testen für die Typzulassungsprüfung. Technische Details bzw. konkrete Prozeduren für spezifische Regelungen sind in dieser Verordnung jedoch nicht enthalten. Das Hauptziel des europäischen Projekts IMVITER (lmplementation of Virtual Testing in Safety Regulations) war es, basierend auf der neuen Verordnung ein virtuelles Testverfahren auszuarbeiten und dabei offene Fragen zu berücksichtigen. Um die im Projekt-Konsortium unter Berücksichtigung der Anliegen aller Interessensgruppen wie Autohersteller, Zulassungsbehörden und technischer Dienste erarbeiteten offenen Punkte zu adressieren, wurde ein generisches Flussdiagramm entwickelt, das den Ablauf einer virtuell basierten Typprüfung darstellt. ln diesem Diagramm ist der virtuelle Typgenehmigungsprozess in drei aufeinander folgende Phasen aufgeteilt, die Verifikations-, Validierungs- und Typgenehmigungsphase. Von entscheidender Bedeutung ist die Phase der Validierung des Simulationsmodells, für die im IMVITER-Projekt eine Methodik vorgeschlagen wurde. Mit der im Projekt vorgeschlagenen Validierungsmethode ist kein Austausch des Simulationsmodells zwischen Fahrzeughersteller und technischem Dienst notwendig, so dass die Vertraulichkeit von Betriebsgeheimnissen nicht gefährdet ist. Zur Validierung des Modells werden jedoch immer Versuche notwendig sein. Dies gilt sowohl für die Überpruefung von passiven als auch aktiven Fahrzeugsicherheitssystemen. Eine zusammenfassende Betrachtung der Erfahrungen aus dem IMVITER-Projekt ergab, dass mit der Einführung von virtuellem Testen keine Erhöhung der Anforderungen an die Fahrzeugsicherheit bzgl. bestehender Regelungen verbunden sein sollte. Jedoch werden auch weiterhin neue zusäztliche Regelungen erforderlich sein, da sich das Unfallgeschehen und die Fahrzeugtechnologie weiterentwickeln und ändern werden. Diese sollten von Beginn an die Möglichkeiten des virtuellen Testens nutzen, insbesondere bei Testverfahren für neue Technologien, z.B. aktiver Fahrzeugsicherheitssysteme. Hier bieten virtuelle Testverfahren nicht nur eine Kosten- oder Zeitersparnis, sondern ermöglichen teilweise erst die sinnvolle Abprüfung von neuen Sicherheitssystemen, die mit aktuellen auf Hardware-Test basierenden Verfahren überhaupt nicht möglich wären.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben. Das Ergebnis kann indes nicht zufriedenstellen. Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird im Beitrag, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der sich auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschrieben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen; dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
Within the automotive context camera monitor systems (CMS) can be used to present views of the traffic situation behind the vehicle to the driver via a monitor mounted inside the cabin. This offers the opportunity to replace classical outside rearview mirrors and therefore to implement new design concepts, aerodynamically optimized vehicle shapes and to reduce the width of the vehicle. Further, the use of a CMS offers the potential to implement functionalities like warnings or situation-adaptive fields of view that are not feasible with conventional rearview mirrors. Despite these potential advantages, it is important to consider the possible technical constraints of this technology and its effect on driver perception and behavior. On the technical side next to the field of view and die robustness of die system, aspects as its functionality at day and night as well as under varying weather conditions should be object to scientific investigation. Concerning human machine interaction, it has to be considered, that the perception of velocities and distances of approaching vehicles might be different for CMS as compared to conventional rearview mirrors and potential influences of factors as the Position of the displays or drivers' age should be taken into account. In order to shed light on these and further open issues, BASt is currently conducting a study that will cover the use of CMS under controlled conditions as well in real traffic. The first part of the study will focus on passenger cars, while in a second step the empirical investigation will be extended to heavy goods vehicles, where the potentials as well as the limitations of CMS might differ considerably. The presentation will cover the first part, with regard to the experimental design, implementation and initial results if already available.
EEVC Status report
(2001)
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
A means of assessing the passive safety of automobiles is a desirable instrument for legislative bodies, the automobile industry, and the consumer. As opposed to the dominating motor vehicle assessment criteria, such as engine power, spaciousness, aerodynamics and consumption, there are no clear and generally accepted criteria for assessing the passive safety of cars. The proposed method of assessment combines the results of experimental safety tests, carried out according to existing legally prescribed or currently discussed testing conditions, and a biomechanical validation of the loading values determined in the test. This evaluation is carried out with the aid of risk functions which are specified for individual parts of the body by correlating the results of accident analysis with those obtained by computer simulation. The degree of conformance to the respective protection criterion thus deduced is then weighted with factors which take into account the frequency of occurrence and the severity of the accident on the basis of resulting costs. Each of the test series includes at least two frontal and one lateral crash test against a deformable barrier. The computer-aided analysis and evaluation of the simulation results enables a vehicle-specific overall safety index as well as partial and individual safety values to be determined and plotted graphically. The passive safety provided by the respective vehicle under test can be defined for specific seating positions, special types of accident, or for individual endangered parts of the body.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
The development of tyre- and truck-manufacturers leads to the direction to introduce wide base single tyres (size 495/45R22,5) instead of twin tyres on the driving axle of trucks, tractors and busses. To study the driving behaviour and safety of various trucks and units with different tyre combinations and loading conditions was the aim of the study. A computer-aided simulation was used for this investigation. Drive tests with a 40 t unit with prototype single tyres on the drive axle were carried out to verify the simulation. Alterations in driving behaviour and driving safety are mainly dependent on the tyre cornering stiffness. The prototype wide single tyres had a higher lateral stiffness which leads to a higher degree of under-steering (safer driving behaviour). The altered spring base on the drive axle had no influence on the side- tilt stability of vehicle combinations but the solo truck profited from the higher rear axle roll stiffness (less danger for roll-over accidents). As far as the driving safety is concerned nothing speaks against wide base tyres on the drive axle. The simulation of a tyre defect in a bend (assuming 40% of the max. transferable side force for the flat tyre) showed no increased danger using wide single tyres. Later driving tests showed however the need of tyre run flat possibilities to avoid jack-knifing of road trains. Also tyre pressure monitoring systems and electronic stability programs for the trucks are advised.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
The GRSP informal group on child restraint systems (CRS) finalised phase 1 of a new regulation for the homologation of CRS . This regulation is the subject of several discussions concerning the safety benefits and the advantages and disadvantages that certain specific points may bring. However, these discussions are sometimes not based on scientific facts and do not consider the whole package but only single items. Based on the experience of the CASPER partners in the fields of human behaviour, accident analysis, test procedures and biomechanics in the area of child safety, a consideration of the safety benefits of phase 1 of the new regulation and recommendations for phase 2 will be given.
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.