Filtern
Erscheinungsjahr
- 2014 (14) (entfernen)
Dokumenttyp
- Konferenzveröffentlichung (14) (entfernen)
Sprache
- Englisch (14) (entfernen)
Volltext vorhanden
- nein (14) (entfernen)
Schlagworte
- Deutschland (6)
- Germany (6)
- Safety (5)
- Sicherheit (5)
- Europa (4)
- Europe (4)
- Risikobewertung (3)
- Risk assessment (3)
- Anfahrversuch (2)
- Attitude (psychol) (2)
Structured road markings are becoming popular as edge line on high speed roads, ensuring night time visibility (retroreflection) during rain. These markings are often also "audio-tactile": vehicles (un)intentionally driving over it may produce much more tyre/road sound, which may be observed in the vehicle but also in the vicinity. The sound increase inside the car can be considered as a positive side effect, as it alarms the driver and may be very helpful for the prevention of "doze off" traffic accidents. The sound increase perceived outside the car however, may have a positive aspect as it can warn people on the emergency lane about the approaching vehicle, but it may as well annoy people living around. A method for the assessment of the acoustic properties of audio-tactile markings has been developed. It is mainly based on the "Close Proximity" (CPX) method, an ISO method intended for the acoustic assessment of pavements. The results of measurement campaigns with CPX trailers in Belgium and Germany according to a specially designed procedure are presented. The feasibility of the method is discussed. The research has been carried out in the frame of the standardization activities of the CEN working group CEN/TC226/WG2 "Horizontal signalization".
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
The use of alcohol interlocks for DUI offenders is widespread around the world. in North America and Australia alcohol interlocks are core elements in the countermeasure system against DUI recidivism. Based on a European experience exchange hosted by the Federal Highway Research Institute (BASt) in October 2013, key features of European alcohol interlock programmes are illustrated. In addition, key findings from international alcohol interlock research are presented. They point towards a need for an accompanying rehabilitative measure in order to achieve long-lasting behavioural changes in the offender. Data from the interlock recorder can be used as predictor for recidivism risk, but also as objective data to aid counselling. Finally, an example of an accompanying rehabilitative measure, which was specifically developed for interlock programmes within a BASt project, is given.
The market introduction and penetration of electric vehicles can be seen as a milestone in order to reduce the environmental burden imposed by the transport sector. The wide-spread use of electric vehicles powered by electricity from renewable sources promises a substantial reduction of local emissions in urban areas as well as greenhouse gas emissions. To be a successful mobility alternative several obstacles and challenges have to be overcome first. Especially the customers' purchase decision determines finally whether an innovation like electromobility will be successful. Therefore, this paper concentrates on demand-related obstacles and barriers for a broad market deployment of electric cars. Within the Electromobility+ project eMAP these issues are investigated via a consumer survey. It was designed to identify the awareness of potential consumers of electric cars as well as give an estimate of the attitude towards this new technology. In addition to the picture of potential demand-related obstacles the consumers were asked to evaluate the suitability of various promotion measures.
In 2011 399 cyclists died in road accidents in Germany and another 76.351 cyclists have been injured. Since 2000 the number of injured or fatally injured cyclists remained on the same high level. Cyclists form 19% of all casualties in German road traffic, although the modal split rate of this transport mode in 2008 was only 10% of trips and resp. 3% of kilometres per day. The high proportion of fatally and seriously injured shows the high vulnerability of cyclists. The demographic shift towards an older population in Germany and the governmental recommendation of increased bicycle use as an ecological, economical and healthy alternative to other modes of transport lead to the assumption that bicycle use especially of elderly people will increase. Based on these facts about the German cyclists' situation a representative survey of 2.000 cyclists was conducted. Results display use patterns and accident involvement on a descriptive level. Overall 7.7% of cyclists report to have been involved in at least one road traffic accident within the last three years. The performed path model analysis reveals an acceptable model fit. Though the explained variance of accident involvement of the applied psychological factors was low, significant relations between several of these factors and especially risky behaviour could be found.
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
Rural roads (highways) in Germany have to provide both high road safety and an appropriate level of service in accordance with their function in the road network. Single carriageway rural roads often underperform these expectations. An analysis of severe accidents on rural roads found two main contributing factors. First, high or inappropriate speed leads to accidents caused by the loss of control of the vehicle. Second, unsafe passing manoeuvres related to a misjudgement of sight distance, speed of oncoming vehicles or a misjudgement of the driver vehicle's acceleration capability. On the five roads where unsafe passing manoeuvres were a main contributing factor to accident occurrence, single short passing lanes (600 m to 1.2 km) were built to provide safe passing. On the remaining two-lane sections passing was prohibited by road signs and road marking. This paper investigates the effect of this design change on the accident situation and on traffic flow. The research project is based on a before/after comparison of traffic and accident data. Traffic volume, vehicle types and their velocities as well as the time gaps between the vehicles were recorded at different cross-sections. The result shows a significant improvement in road safety. This improvement was especially noted for severe head-on crashes, which were reduced to almost zero. The analysis of traffic flow on these roads pointed out that the chosen lengths of passing lanes were sufficient for safe passing and thereby reduced the need for dangerous driving behaviour. The recommendations of this research were fundamental for the determination of the design parameters of the second highest design class (EKL 2) in the new German Rural Road Design Guideline (RAL) published in spring 2013.
In the project SECMAN " SECurity MANual " a simple four-step procedure for the identification of critical road infrastructures, assessment of these infrastructures regarding various man-made threats and the determination of effective protection measures was developed. These methodologies are summarized and combined into a comprehensive best-practice manual which allows for a trans-national structured and holistic security-risk-management approach for owners and operators of road infrastructures in Europe. This paper presents the developed methodology starting from the assessment procedures of a network's criticality over an object's attractiveness and vulnerability to the selection process of appropriate protection measures.
The paper describes the development of transitions between different safety barriers in Germany but also in the context of the European standardization. In the paper practical and impact test expriences with transitions are shown. In view of the sheer number of theoretically possible combinations of safety barriers, the demand for testing every transition, even if the connecting safety barriers differ only slightly, appears to be economically unacceptable. On the other hand the experience from accidents and also from failed impact tests shows that transitions can be a risk to traffic safety. Therefore criteria for the distinction between transitions (impact test required/impact test unnecessary) are explained. In order to distinguish transitions which do not have to be impact-tested from those that require impact tests, criteria were developed and formulated.
Improving the security of critical road infrastructure is a major task for owners and operators of tunnels and bridges in the European TEN-T Network (Trans-European Networks of Transport) (European Parliament and Council 1996). Up to now, there has not been a systematic procedure for identifying and assessing critical infrastructure objects and selecting appropriate protection measures. The EC FP7 project SeRoN for the first time presents an innovative methodology in order to support road owners and operators in handling this complex task. This paper describes the methodology and project results in detail by giving an introduction into its practical application.
According to an investigation in March 2008 by the Federal Ministry of Transport, Building and Urban Affairs (BMVBS) about 14,000 truck parking spaces are missing in the near of motorways in Germany. Beside constructional enlargement of rest areas, intelligent traffic systems ought to be used to detect automatically the occupancy rate of rest areas and to provide better demand management and also to achieve an increase of capacity of truck parking spaces. The essay describes the newly developed control procedure "Compact parking", which is currently under development by German Federal Highway Research Institute (BASt). The method achieves that a number of trucks are parking in a compact way, side by side and without a driving lane between them. With the help of dynamic displays above the parking rows, the drivers receive the needful information to park their vehicle in a parking row, in which other trucks have the same or an earlier departure time. This system is able to increase the rest area capacity in short-term, more quickly than constructional enlargement of rest areas.
Due to the publication of guidelines in Germany the possibility exists to offer analytical designed construction works within an alternative proposal. But the extent to which the test specimen production influences the design relevant properties (for the same asphalt mixture) is not sufficiently investigated at present. Objective of this research project was to determine the design relevant asphalt properties by tests and do comparative considerations on two selected locations within the renewal of a federal trunk road (Germany). For the comparative consideration of the design relevant asphalt properties mixture samples were taken during paving and afterwards drill cores were taken at the same locations. Fatigue tests and tests to determine the stiffness were conducted with the Indirect Tensile Test (ITT). Then design calculations having regard to the test results were performed. At this different bearing conditions of the asphalt package were considered. The calculated fatigue conditions were comparative evaluated and they are presented and discussed in this paper.
Tempered road system
(2014)
The road performance is strongly influenced by climatic conditions. Winter conditions have massive impact on traffic security but also pavement lifetime decreases as an effect of temperature variation during wintertime and summertime. Heating and cooling of a pavement is a possibility to work against these impacts. To discuss the boundary conditions for an efficient construction and operation of a tempered road system a feasibility study has been made. The study shows the feasibility and identifies thermal energy buffering as a main challenge. When thinking of a fully regenerative operation of a large tempered road system (e.g. 20.000 m-²) the storage volume has to be too large for an economic and structurally engineered satisfactory solution. However, the location dependent usage of natural geothermal storage possibilities and as well smart alignment and construction promises a feasibility realization.
Various climate projections predict changing climatic parameters like temperature, precipitation, wind speed etc. for Germany. This could have severe impacts on road transport infrastructure as well as road traffic itself. At the Federal Highway Research Institute (Bundesanstalt für Straßenwesen (BASt) a strategy was developed to adapt roads and engineering structures to the impacts of climate change. The strategy "Anpassung der Straßenverkehrsinfrastruktur an den Klimawandel / Adaptation of the road infrastructure to climate change (AdSVIS)" comprises currently about 15 projects. On the basis of the identification of the hazards and the combination of the climate and road network data, the road transport infrastructure which might be affected is to be determined. Adaptation measures are to be developed for the identified risk areas and assessed as to their effectiveness. Special attention is given to international cooperation since climate change is a truly global challenge.