Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (187) (entfernen)
Volltext vorhanden
- nein (187) (entfernen)
Schlagworte
- Safety (57)
- Sicherheit (57)
- Bewertung (42)
- Evaluation (assessment) (41)
- Germany (39)
- Deutschland (38)
- Test method (36)
- Anfahrversuch (34)
- Impact test (veh) (34)
- Prüfverfahren (33)
Institut
As bearing capacity measurements become more and more important, the necessity of assuring quality by establishing a QA system becomes more relevant. Within this context, the FGSV recommends the introduction of comparative measurements. Since 2015, two pilot events took place, with the main aim of introducing repetitive comparative measurements, in which all FWD operators shall participate. The results of the comparative measurements show that the basic principles behind comparative measurements (of the FWD), elaborated as a Europe-wide consensus and put into practice in the Netherlands and the United Kingdom, are valid, but still there is a variety of questions to be answered concerning certain details of the measuring system itself, e. g. measurement of the temperatures (air, pavement) and the impact of load introduction. All in all, the two pilot events in 2015 and 2016 proved that the comparability of the different FWD measuring devices is satisfactory.
Measuring and characterizing airborne particulate matter (PM) is an important research area because PM can lead to impacts on health and to visibility reduction, material damage and groundwater pollution. In regard to road dust, suspension and re-suspension and the contribution of non-exhaust PM to total traffic emissions are expected to increase as a result of predicted climate scenarios. European environmental regulations have been enforced to reduce exhaust particle emissions from road traffic, but little attention has been paid to reducing non-exhaust coarse particle emissions due to traffic. Therefore, a monitoring program for coarse PM has been initiated in early 2013 to assess the predicted increase in the abundance of non-exhaust particles. Particle sampling was performed with the passive-sampler technique Sigma-2. The subsequent single-particle analysis allows for characterization of individual particles, determination of PM size distribution, and calculation of PM mass concentrations. Two motorways n ear Cologne (Koeln), Germany were selected as sampling sites, and the experimental setup in the field was realized with a so-called twin-site method. The present study reports single-particle analysis data for samples collected between May 31, 2013 and May 30, 2014. Coarse PM, generated through multi-source mechanisms, consists of, e.g., tire-wear, soot aggregates, and mineral dust. The highest mass concentration occurs at both motorways in spring, and the observed PM mainly contains traffic-abrasion particles. The field measurements show that the minimum PM concentration was found in the 5 to 12-°C temperature range, whereas the maximum concentration was observed in both the "5 to 5-°C and the 12 to 24-°C ranges, in agreement with previous laboratory measurements. Correlation between super-coarse (d p 10"80 μm, geometric equivalent diameter) PM concentration and precipitation displays a significant increase in concentration with decreasing number of precipitation events (dry weather periods).
Urban runoff is known to transport a significant pollutant load consisting of e.g. heavy metals, salts and hydrocarbons. Interactions between solid and dissolved compounds, proper understanding of particle size distribution, dissolved pollutant fractions and seasonal variations is crucial for the selection and development of appropriate road runoff treatment devices. Road runoff at an arterial road in Augsburg, Germany, has been studied for 3.5 years. A strong seasonal variation was observed, with increased heavy metal concentrations with doubled and tripled median concentrations for heavy metals during the cold season. Correlation analysis showed that de-icing salt is not the only factor responsible for increased pollutant concentrations in winter. During the cold period, the fraction of dissolved metals was lower compared to the warm season. In road dust, the highest metal concentrations were measured for fine particles. Metals in road runoff were found to show a significant correlation to fine particles SS63 (<63 μm). Therefore, it is debatable whether treatment devices only implementing sedimentation processes provide sufficient removal rates.
Road authorities, freight, and logistic industries face a multitude of challenges in a world changing at an ever growing pace. While globalization, changes in technology, demography, and traffic, for instance, have received much attention over the bygone decades, climate change has not been treated with equal care until recently. However, since it has been recognized that climate change jeopardizes many business areas in transport, freight, and logistics, research programs investigating future threats have been initiated. One of these programs is the Conference of European Directors of Roads (CEDR) Transnational Research Programme (TRP), which emerged about a decade ago from a cooperation between European National Road Authorities and the EU. This paper presents findings of a CEDR project called CliPDaR, which has been designed to answer questions from road authorities concerning climate-driven future threats to transport infrastructure. Pertaining results are based on two potential future socio-economic pathways of mankind (one strongly economically oriented "A2" and one more balanced scenario "A1B"), which are used to drive global climate models (GCMs) producing global and continental scale climate change projections. In order to achieve climate change projections, which are valid on regional scales, GCM projections are downscaled by regional climate models. Results shown here originate from research questions raised by European Road Authorities. They refer to future occurrence frequencies of severely cold winter seasons in Fennoscandia, to particularly hot summer seasons in the Iberian Peninsula and to changes in extreme weather phenomena triggering landslides and rutting in Central Europe. Future occurrence frequencies of extreme winter and summer conditions are investigated by empirical orthogonal function analyses of GCM projections driven with by A2 and A1B pathways. The analysis of future weather phenomena triggering landslides and rutting events requires downscaled climate change projections. Hence, corresponding results are based on an ensemble of RCM projections, which was available for the A1B scenario. All analyzed risks to transport infrastructure are found to increase over the decades ahead with accelerating pace towards the end of this century. Mean Fennoscandian winter temperatures by the end of this century may match conditions of rather warm winter season experienced in the past and particularly warm future winter temperatures have not been observed so far. This applies in an even more pronounced manner to summer seasons in the Iberian Peninsula. Occurrence frequencies of extreme climate phenomena triggering landslides and rutting events in Central Europe are also projected to rise. Results show spatially differentiated patterns and indicate accelerated rates of increases.
Efficient and widely available transport infrastructure is one of the most important prerequisites for sustainable economic development to meet the demand for mobility. In this context, being able to manage traffic growth forecasts is of particular importance. In Germany, current forecasts indicate a 40% increase in rail and road transport in the country. However, about 60% of bridges (as measured by bridge area) on the national German highway system that are suitable for freight transport were built before 1985. In other transport sectors as well, aging infrastructure is one of the key challenges for the availability and the resilience of European transport infrastructure. Many bridges in the national German highway system are already at their load-bearing limit. Furthermore, required maintenance measures have not been adequately carried out in the past due to limited budgets, leading to overall bridge deterioration. Further challenges for owners and operators of transport infrastructure result from the effects of climate change, associated climate extremes, natural catastrophes, and possible criminal and terrorist threats. To ensure that future infrastructure challenges can be successfully addressed, strategies and solutions must be developed and implemented in a timely manner to enable holistic and sustainable life-cycle management. The concepts of Resilience Management as well as Resilience Engineering are essential building blocks in this process. Resilience is the ability to survive in the face of a complex, uncertain, and ever-changing future. It is a way of thinking about both short-term cycles and long-term trends. Using this concept, owners and operators can reduce the risk of disruption in the face of shocks and stresses. Resilience requires cyclical, proactive, and holistic risk management practices.
The aging structure as well as the considerable increase of heavy-traffic load on Germany's motorways and trunk roads encourages the use of innovative, sound and reliable methods for the structural assessment on network level as well as on project level. Essential elements for this are data, which allow a reliable assessment. For a holistic approach to structural pavement assessment performance orientated measurements will be necessary. In combination with functional parameters as well as write-down models, strategically motivated decision making processes will be useful combined with technically motivated decision processes. For the application at the network level, the available methods for performance orientated measurements are still challenging, as they are based either on testing drill-cores or on non traffic speed methods. In recent years significant innovation steps have been made to bring traffic speed bearing capacity measurements and methods for evaluating pavement structures on the road. The paper summarizes the actual assessment procedures in Germany as well as the ongoing work on the development and implementation of new methods and techniques.
A sociological perspective on different strategies of reward in urban traffic law enforcement
(1996)
In order to enhance road safety, it is necessary to make road users change their behaviour. There are two forms of police enforcement: punishment for breaking traffic regulations and rewards for rule-conformist behaviour. Punishment does not appear to produce long term changes. There are two main reward strategies: individual and group dependent rewards. Individuals who are members of a clearly defined group have good prospects of winning prizes in a lottery. The strategy of the delegated group dependent reward is based on a donation to a social institution. Traffic safety is a conflict of interests, and game theory considerations can be applied. Results of German and Dutch studies confirm hypotheses based on the game theory concept. Traffic behaviour mostly depends on expectation of others' behaviour. Successful strategies of reward should always be based on individual settlements of the rewards. More investigations are needed. Strategies of group dependent reward are not recommended. The size of reward and probability of winning it should be linked to rate of participation: the greater the participation, the greater the value of reward and probability of winning it. Every driver has a threshold from which he is prepared to change his traffic behaviour for a reward.
The field of safety in road tunnels has always been an important issue for operators, owners and the responsible authorities. After the tunnel accidents in 1999 the subject gained however in importance. On European level the Directive 2004/54 EC on "Minimum safety requirements for tunnels in the Trans European Road network" has been published. This guideline has to be implemented into national law by all Member States. According to the guideline all Member States of the European Community shall develop a methodology for risk analyses to be applied in certain cases. For Germany, a standardized methodology for a probabilistic quantitative risk assessment has been worked out.
A very high service availability is important for the operator and for the user of road tunnels, too. The service availability of a structure is directly related to its quality. The earlier quality assurance measures are being considered during the life cycle, the better a structure of high quality can be guaranteed. Problems which occur during the operation period of a structure often result from design errors or from inadequate realisation during the construction phase. They may also occur as a result of wrongly planned maintenance and refurbishment works. Thus, the transfer of specific data, information and experiences through the whole life cycle is very important. In this context methods of facility management can provide efficient assistance when they have already been used throughout all three classic phases of a structure's life cycle - planning, construction and operation. Finally the tunnel drainage system of German road tunnels is considered as an example as practical application possibility.
This paper deals with the determination of test criteria for the durability assessment of polyvinyl chloride (PVC)-based geosynthetic barriers (GBR-P) products in tunnel sealing systems. In the project different products for road tunnel application are investigated by systematic long time storage in hot water using a new test procedure based on SIA V 280 standard (test no. 13) and EN 14415. The objective of this research project is to derive suitable exposure conditions and criteria for a practical testing procedure with regard to service lifetimes of up to 100 years. For that test temperature and time as well as the best suitable test medium have been investigated in a structured way. To verify the results of the new test procedure the material properties of GBR-P samples removed from older road tunnels are investigated. Based on the presented results of the still on-going research program some preliminary conclusions regarding the updating of the German regulations for road tunnel sealing systems (ZTV-ING part 5 section 5 and TL/TP KDB) are given.
The Federal Highway Network of Germany represents considerable fixed assets. Construction and maintenance activities not only require a high budget, but also influence the traffic infrastructure and, thus, the economy and society as a whole. The present safety of the network has to be ensured under consideration of environmental aspects. At the same time the network owner has to make sure that the civil works are carried out in the most efficient way. Considering the fact that financial resources are restricted, the costs have to be spent in a way to obtain the greatest possible benefit. This task is supported by the application of a comprehensive Asset Management, which is subdivided into operational and controlling tasks respectively. The paper describes the current management procedures.
The first stage of the work has been to collate information on bridge assessment from the participating countries. In the later stages, the aim is to provide guidelines that reflect the current best practices, a methodology that will allow for future development and sufficient flexibility to accommodate variations in national priorities as the process of harmonisation is pursued. The following tasks fall within the scope of the project: (1) a review of current procedures and standards used for bridge assessment in Europe; (2) the development of models for taking into account the bridge specific traffic conditions and material properties; (3) the use of reliability methods based on a probabilistic approach for bridge assessment including the use of measurements for updating the reliability of structural elements; and (4) the provision of recommendations for methods and procedures that can be adopted for the assessment module of the management framework highlighting where further development will be beneficial.
Germany's road infrastructure grew over centuries to become the arteries and lifelines of our society. The present safety of the infrastructure has to be ensured under consideration of environmental aspects. At the same time the owner has to make sure that the maintenance activities are carried out in the most efficient way. Considering the fact that financial resources are restricted, maintenance costs have to be spent in a way to obtain the greatest possible benefit. In the case of bridges, which are one of the most important parts of the road infrastructure in Germany, this task is supported by the application of a bridge management system (BMS). The existing German BMS contains assessment and optimization procedures on object and network level and is the basis for advancements to meet future demands. Developments concern life cycle and quality-oriented, holistically optimized procedures. Reasonable infrastructure management will contribute to meeting efficiency and sustainability objectives and to achieving interoperability. Here holistic network infrastructure management methods are required. There is a strong need for management solutions during the whole service life of a structure. The definition of criteria for evaluation of the relevance of failure mechanisms, including acceptance thresholds, requires the availability of relevant data for management procedure. Tools for innovative investigation methods and an effective data management will help in meeting the requirements. Relevant fields of research are improved maintenance strategies to meet future demands concerning heavy goods traffic, application and further development of nondestructive testing methods for efficient and sustainable management structures, and the improvement of analytic management tools to meet future demands.
The goal of the project FIMCAR (Frontal Impact and Compatibility Assessment Research) was to define an integrated set of test procedures and associated metrics to assess a vehicle's frontal impact protection, which includes self- and partner-protection. For the development of the set, two different full-width tests (full-width deformable barrier [FWDB] test, full-width rigid barrier test) and three different offset tests (offset deformable barrier [ODB] test, progressive deformable barrier [PDB] test, moveable deformable barrier with the PDB barrier face [MPDB] test) have been investigated. Different compatibility assessment procedures were analysed and metrics for assessing structural interaction (structural alignment, vertical and horizontal load spreading) as well as several promising metrics for the PDB/MPDB barrier were developed. The final assessment approach consists of a combination of the most suitable full-width and offset tests. For the full-width test (FWDB), a metric was developed to address structural alignment based on load cell wall information in the first 40 ms of the test. For the offset test (ODB), the existing ECE R94 was chosen. Within the paper, an overview of the final assessment approach for the frontal impact test procedures and their development is given.
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
This study was one part of the research activities of work package 5 "Rehabilitation" of the integrated EU DRUID project (6th Framework Programme). It aimed at gathering information about the cognitive"affective and behavioral processes that participants undergo while attending driver rehabilitation (DR) programs. The primary objective was to analyze the outcomes of group interventions for alcohol offenders in order to assess any cognitive, motivational and behavioral modifications within individual participants and to identify the relevant variables which initiate and support this change process. The general methodological concept of the study was a prospective cohort design of participants of group-based European driver rehabilitation programs, carried out via a participant feedback questionnaire survey. In total N=7.339 DUI offenders in 9 European countries (Austria, Belgium, France, Germany, Great Britain, Hungary, Italy, Netherlands and Poland) participated in the survey. The results indicate that DR participants feel such programs provide strong support for their cognitive and behavioral change processes. The findings suggest that participants feel encouraged to establish new behavioral goals and the commitment to stick to them. At the same time, the participants' ratings emphasize the important role of the course leader in encouraging such changes. The findings of this explorative questionnaire survey are promising. Although it is impossible to draw any conclusions regarding long-term behavioral changes or effects on recidivism rates, participants of DR courses express positive feedback on completion of the program. The positive outcomes of the study can motivate decisionmakers to launch DR measures and to regard them as an essential part of a comprehensive countermeasure system against DUI.
The use of alcohol interlocks for DUI offenders is widespread around the world. in North America and Australia alcohol interlocks are core elements in the countermeasure system against DUI recidivism. Based on a European experience exchange hosted by the Federal Highway Research Institute (BASt) in October 2013, key features of European alcohol interlock programmes are illustrated. In addition, key findings from international alcohol interlock research are presented. They point towards a need for an accompanying rehabilitative measure in order to achieve long-lasting behavioural changes in the offender. Data from the interlock recorder can be used as predictor for recidivism risk, but also as objective data to aid counselling. Finally, an example of an accompanying rehabilitative measure, which was specifically developed for interlock programmes within a BASt project, is given.
In Germany road tunnels on major roads which are longer than 400 m have to be monitored permanently. For that purpose the tunnels are equipped with a multitude of monitoring and detection systems whose data and messages are transmitted to tunnel control centres. Due to the higher traffic density, the increasing number of tunnels to be monitored and road users" demand of higher safety and security levels, the strains on operating staff of tunnel control centres have continuously been growing. Therefore, innovative approaches have been developed in two recent German research projects: RETISS " Real Time Security Management System, and ESIMAS " Real-time Safety Management System for road Tunnels. Both systems are designed to allow faster and more efficient reaction of tunnel operators in order to maintain the capacity and availability of transport infrastructures but also to improve the safety and security of road users.
The market introduction and penetration of electric vehicles can be seen as a milestone in order to reduce the environmental burden imposed by the transport sector. The wide-spread use of electric vehicles powered by electricity from renewable sources promises a substantial reduction of local emissions in urban areas as well as greenhouse gas emissions. To be a successful mobility alternative several obstacles and challenges have to be overcome first. Especially the customers' purchase decision determines finally whether an innovation like electromobility will be successful. Therefore, this paper concentrates on demand-related obstacles and barriers for a broad market deployment of electric cars. Within the Electromobility+ project eMAP these issues are investigated via a consumer survey. It was designed to identify the awareness of potential consumers of electric cars as well as give an estimate of the attitude towards this new technology. In addition to the picture of potential demand-related obstacles the consumers were asked to evaluate the suitability of various promotion measures.
In 2011 399 cyclists died in road accidents in Germany and another 76.351 cyclists have been injured. Since 2000 the number of injured or fatally injured cyclists remained on the same high level. Cyclists form 19% of all casualties in German road traffic, although the modal split rate of this transport mode in 2008 was only 10% of trips and resp. 3% of kilometres per day. The high proportion of fatally and seriously injured shows the high vulnerability of cyclists. The demographic shift towards an older population in Germany and the governmental recommendation of increased bicycle use as an ecological, economical and healthy alternative to other modes of transport lead to the assumption that bicycle use especially of elderly people will increase. Based on these facts about the German cyclists' situation a representative survey of 2.000 cyclists was conducted. Results display use patterns and accident involvement on a descriptive level. Overall 7.7% of cyclists report to have been involved in at least one road traffic accident within the last three years. The performed path model analysis reveals an acceptable model fit. Though the explained variance of accident involvement of the applied psychological factors was low, significant relations between several of these factors and especially risky behaviour could be found.