Filtern
Erscheinungsjahr
Dokumenttyp
Schlagworte
- Impact test (veh) (45) (entfernen)
Institut
- Abteilung Fahrzeugtechnik (45) (entfernen)
The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx. However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My. The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was observed. It was also observed that the primary neck response in these tests was flexion, not extension. This correlates well with recent findings from Japan and the United States showing a correlation between neck flexion and injury in accident replication simulations and postmortem human subjects (PMHS) studies, respectively. The present certification tests may not adequately control front cervical spine bumper characteristics, which are important for neck flexion response. The certification sled test also does not include the pelvis and so cannot be used to control pelvis response and does not substantially load the lumbar bumpers and so does not control these parts of the dummy. The stiffness of all spine bumpers and of the pelvis flesh should be much more tightly controlled. It is recommended that a method for certifying the front cervical bumpers should be developed. Recommendations are also made for tighter tolerance on the input parameters for the existing certification tests.
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
Streuung von Schutzkriterien in kontrollierten Aufprallversuchen gegen die starre 30 Grad-Barriere
(1983)
Gegenstand der Arbeit ist die Ermittlung von Streubreiten von Fahrzeug- und Dummy-Messwerten in Aufprallversuchen bei Geschwindigkeiten von 50 km/h gegen eine starre 30-°-Barriere. Zu den fahrzeugseitigen Messwerten gehörten die Deformation der Frontstruktur, die maximale Fahrzeugverzögerung, die mittlere Fahrzeugverzögerung und Anforderungen der ECE-Regelung 33. Die gemessenen Standardabweichungen der Einzelwerte lagen mit zwei bis sieben Prozent deutlich unter zehn Prozent. Höhere Standardabweichungen der Messwerte wurden dann beobachtet, wenn Aufpralle nach den Mustern Kopf-Lenkrad (Fahrer), Brust-Lenkrad (Fahrer) und Knie-Armaturentafel (Fahrer und Beifahrer) nicht in allen Versuchen zu beobachten sind. Hohe Streubreiten für die Kopfbeschleunigung bzw. die Beschleunigung der Brust des Dummy auf dem Fahrersitz wurden dadurch verursacht, dass in einem Versuch eine unübliche Vorverlagerung des Dummys infolge mangelhafter Gurtwirkung mit nachfolgendem Brust-Lenkrad-Kontakt zu beobachten war.
Anhand von zwei verschiedenen Versuchskonfigurationen wurde das Schutzpotential von Kopfschutzsystemen (Fahrradhelm und airbagbasiertes System) untersucht. Hierbei wurden die resultierende Kopfbeschleunigung als Messwert sowie das Kopfverletzungskriterium HIC bei Versuchen ohne und mit Kopfschutzsystem vergleichend gegenübergestellt.
Wegen der wachsenden Verbreitung von Fahrradanhängern zum Kindertransport und der möglichen Unfallgefährdung ist im vorliegenden Forschungsprojekt deren passive Sicherheit untersucht worden. Zudem wurde der Frage nachgegangen, ob der Transport von Kindern im Fahrradanhänger sicherer ist als mit dem Fahrrad mit Kindersitzen. In Absprache mit Herstellern und Vertreibern wurden verschiedene Untersuchungen durchgeführt. Es handelte sich um Anprallversuche (Anfahrversuche), Rollwagenversuche (Schlittenversuche) sowie Kopffreiheitsprüfungen und Fallversuche. Bei den Versuchen waren die Prüfobjekte mit einem oder zwei Dummies besetzt, die mit Messdatenaufnehmern ausgestattet waren. Verschiedene Messdaten, zum Beispiel Kopf- und Brustbeschleunigung, wurden erfasst und ausgewertet. Zusätzlich wurde das Kopfschutzkriterium (HPC) berechnet und bewertet. Entstandene Schäden an den Prüfobjekten wurden aufgenommen und durch Fotos dokumentiert. Die Versuchsabläufe selbst wurden mit Hochgeschwindigkeitskameras aus verschiedenen Positionen aufgezeichnet. Beim Anfahrversuch mit einem Pkw gegen ein Gespann aus Fahrrad und Anhänger waren direkte Anstöße der Anhängerinsassen an die Pkw-Front zu erkennen. Die Beschleunigungswerte waren dabei relativ hoch. Anstöße gegen Anhängerinnenteile waren bei fast allen Versuchen zu beobachten. Teilweise wurden Radaufhängungen und Radnaben beschädigt. Durch die Rollwagenversuche wurden konstruktive Schwächen bei den Sitzen und Rückhaltesystemen festgestellt. Nähte, Befestigungen und Verstellösen wurden zerstört. Es stellte sich heraus, dass die Qualität des Gurtsystems, die Steifigkeit des Anhängeraufbaus, die Sitzposition der Kinder und die vorhandene Kopffreiheit ausschlaggebend für das Verletzungsrisiko der Insassen sind. Bei den Versuchen mit Fahrradsitzen ergaben sich hohe Beschleunigungswerte durch den direkten Kontakt des Radfahrers mit der Fahrzeugfront und/oder der Fahrbahn. Das Gewicht des Radfahrers, des Fahrrades und auch Fahrradteile bergen ein erhöhtes Verletzungsrisiko für das Kind. Zusätzlich besteht die Gefahr überfahren zu werden, wenn das Kind nach dem Sturz des Fahrrades ungeschützt auf der Fahrbahn liegt. Ein direkter Vergleich der beiden Transportmöglichkeiten war aufgrund der geringen Daten der Versuche mit Fahrradkindersitzen nur bedingt möglich. Tendenziell ist der Transport der Kinder im Fahrradanhänger als weniger gefährlich zu bewerten. Es werden die Vor- und Nachteile dargestellt. Zur Bewertung der Sicherheit von Fahrradanhängern wurden die folgenden Prüfmethoden erarbeitet: - Pendelschlagprüfung für die gesamte Chassisstruktur; - Kopffreiheitsprüfung; - Belastungsprüfung der Aufbaustruktur; - Festigkeitsprüfung der Gurtsysteme. Die Prüfungen sind so aufgebaut, dass sie mit einfachen Mitteln durchzuführen sind. Es sollte somit jedem Anhängerhersteller möglich sein, die passive Sicherheit seiner Produkte umfassend zu untersuchen. Die Prüfverfahren für die Sicherheitsbewertung sollen in eine DIN-Norm und in das Merkblatt für Fahrradanhänger einfließen. Der Original-Forschungsbericht enthält einen umfangreichen Fotoband zu den Einzelheiten der Versuche und Versuchsaufbauten sowie zu den Beschädigungen der Prüfobjekte und kann bei der BASt eingesehen werden.
Upcoming test procedures and regulations consider the use of Q-dummies. Especially Q6 and Q10 will be introduced to assess the safety of child occupants in vehicle rear seats. Therefore detailed knowledge of these dummies is important to improve safety. As recent studies have shown, chest deflection measurements of both dummies are influenced by parameters like belt geometry. This could lead to a non optimized design of child restraint systems (CRS) and belt systems. The objective of this study is to obtain a more detailed understanding of the sensitivity of chest measurements to restraint parameters and to investigate the possibilities of chest acceleration as an alternative for the assessment of chest injury risks. A study of frontal impact sled tests was performed with Q6 and Q10 in a generic rear seat environment on a bench. Belt parameters like modified belt attachment locations were varied. For the Q6 dummy, different positioning settings of the CRS (booster with backrest) and of the dummy itself were investigated. The Q10 dummy was seated on a booster cushion. Here the position of the upper belt anchorage point was varied. To simulate the influence of vehicle rotation in the ODB crash configuration, the bench was pre-rotated on the sled in additional tests with the Q10. This configuration was tested with and without pretensioner and load limiter. Chest deflection in Q6 showed a high sensitivity to changes in positioning of the CRS and the dummy itself. A more slouched position of the CRS or dummy resulted in a reduction of measured chest deflection, whereas chest acceleration increased for a more slouched position of the CRS. Chest deflection in Q10 is sensitive to belt geometry as already shown in other studies. In a more outboard position of the shoulder belt anchorage the measured chest deflection is higher. Chest acceleration shows the opposite tendency, which is highest for the rearmost location of the upper belt anchorage. On a pre-rotated bench the highest chest deflection within this test series was observed without load limiter/pretensioner and an outboard belt position. By optimizing the belt location and the use of pretensioner/load limier the chest deflection was significantly reduced. For the Q6 a criterion based on chest acceleration as well as deflection measured at two locations might be the most reliable approach, which requires further research with an additional upper deflection sensor. In the Q10 the measured chest deflection does not always correctly reflect the severity of chest loading. The deflection is depending on initial belt position and restraint parameters as well as test conditions, which result in different directions of belt migration. A3ms chest acceleration might be a better indicator for severity of chest loading independent of different conditions like belt geometries. However, in some cases the benefit of an optimized restraint system could only be shown by deflection. These findings suggest that further research is needed to identify a chest injury assessment method, which could be based on deflection as well as acceleration or other parameters related to belt to occupant interaction.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
Supported by field accident data and monitoring results of European Regulation (EC) No. 78/2009, recent plans of the European Commission regarding a way forward to improve passive safety of vulnerable road users include, amongst other things, an extension of the head test area. The inclusion of passive cyclist safety is also being considered by Euro NCAP. Although passenger car to cyclist collisions are often severe and have a significant share within the accident statistics, cyclists are neither considered sufficiently in the legislative nor in the consumer ratings tests. Therefore, a test procedure to assess the protection potential of vehicle fronts in a collision with cyclists has been developed within a current research project. For this purpose, the existing pedestrian head impact test procedures were modified in order to include boundary conditions relevant for cyclists as the second big group of vulnerable road users. Based on an in-depth analysis of passenger car to cyclist accidents in Germany the three most representative accident constellations have been initially defined. The development of the test procedure itself was based on corresponding simulations with representative vehicle and bicycle models. In addition to different cyclist heights, reaching from a 6-year-old child to a 95%-male, also four pedal positions were considered. By reconstruction of a real accident the defined simulation parameters could be validated in advance. The conducted accident kinematics analysis shows for a large portion of the constellations an increased head impact area, which can reach beyond the roof leading edge, as well as high average values for head impact velocity and angle. Based on the simulation data obtained for the different vehicle models, cyclist-specific test parameters for impactor tests have been derived, which have been further examined in the course of head and leg impact tests. In order to study the cyclist accident kinematics under real test conditions, different full scale tests with a Polar-II dummy positioned on a bicycle have been conducted. Overall, the tests showed a good correlation with the simulations and support the defined boundary test conditions. Typical accident scenarios and simulations reveal higher head impact locations, angles and velocities. An extended head impact area with modified test parameters will contribute to an improved protection of vulnerable road users including cyclists. However, due to significantly differing impact kinematics and postures between the lower extremities of pedestrians and cyclists, these injuries cannot be addressed by the means of current test tools such as the flexible pedestrian legform impactor FlexPLI. Based on the findings obtained within the project as well as the existing pedestrian protection requirements a cyclist protection test procedure for use in legislation and consumer test programmes has been developed, whose requirements have been transferred into a corresponding test specification. This specification provides common head test boundary conditions for pedestrians and cyclists, whereby the existing requirements are modified and two parallel test procedures are avoided.