Konferenzveröffentlichung
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (637) (entfernen)
Schlagworte
- Conference (386)
- Konferenz (382)
- Germany (212)
- Deutschland (209)
- Unfall (188)
- Accident (187)
- Safety (123)
- Sicherheit (122)
- Injury (117)
- Verletzung (117)
Institut
This paper set out to examine the possibilities for injury avoidance implications for older drivers in crashes, based on crash and injury patterns among older drivers and current trends in ageing in most western societies. A number of safety technologies were identified and discussed which have potential for improving vehicle older driver crash avoidance and crashworthiness. While there were some promising estimates available of the likely benefits of this technology for improving safety, it is evident that they need to be confirmed for older drivers, given their age-related disabilities and sensory limitations. Further research is urgently required to ensure that these technologies yield safety benefits without any disbenefits for older drivers.rn
Whiplash injuries are characterized by the high variability of its symptoms and by the subjectivity of its diagnosis, which sometimes leads to frauds perpetrated by victims of rear-end impacts. It is estimated that whiplash injuries cost annually about 10.000 million Euros in Europe. Therefore, the aim of this study was to investigate the influence of the dynamics of the accident in which the victim was involved in the probability of development of whiplash associated injuries. In the presented methodology, first an accident reconstruction is performed where the dynamics of the accident is determined. This is carried out using the software PC-Crash, police and insurance companies' data. Then biomechanical injuries criteria related with whiplash injuries are evaluated. For the evaluation of the probability of having whiplash injuries, the Neck Injury Criterion (NIC) of the victim and the mean acceleration of the vehicle were evaluated. Then, with medical reports, the results of the accident reconstruction are correlated with the reported injuries. Some examples are presented. The results obtained indicate that the study of the dynamics of the road accidents in which the victims were involved could be used as an auxiliary of the prognosis of whiplash injuries and is important for a precise diagnosis of this type of injuries.
A national initiative from the vehicle manufacturers, safety system suppliers, the road administration and universities in Sweden took off in 2007. The aim was to develop a national investigation network and a methodology focusing on all phases of a crash (pre-crash, in-crash and post-crash) as well as all parts of the road transport system (road user, vehicle and road environment). The initiative is formally run as a project with the acronym INTACT (Investigation Network and Accident Collection Techniques). It was a three year pilot with the aim to develop methodologies for an extended national crash investigation activity. During the first year the INTACT partners agreed on the aim for the investigation and methods for retrieving the data were developed. During the second and third year the methodology was tested in real-world investigations and further refinement was made. The paper describes the methodology developed to obtain high qualitative in-depth road crash data.
The overall purpose of the ASSESS project is to develop a relevant and standardised set of test and assessment methods and associated tools for integrated vehicle safety systems, primarily focussing on currently available pre-crash sensing systems. The first stage of the project was to define casualty relevant accident scenarios so that the test scenarios will be developed based on accident scenarios which currently result in the greatest injury outcome, measured by a combination of casualty severity and casualty frequency. The first analysis stage was completed using data from a range of accident databases, including those which were nationally representative (STATS19, UK and STRADA, SE) and in-depth sources which provided more detailed parameters to characterise the accident scenarios (GIDAS, DE and OTS, UK). A common analysis method was developed in order to compare the data from these different sources, and while the data sets were not completely compatible, the majority of the data was aligned in such a way that allowed a useful comparison to be made. As the ASSESS project focuses on pre-crash sensing systems fitted to passenger cars, the data selected for the analysis was "injury accidents which involved at least one passenger car". The accident data analysis yielded the following ranked list of most relevant accident scenarios: Rank Accident scenario 1 Driving accident - single vehicle loss of control 2 Accidents in longitudinal traffic (same and opposite directions) 3 Accidents with turning vehicle(s) or crossing paths in junctions 4 Accidents involving pedestrians The ranked list highlights the relatively large role played by "accidents in longitudinal traffic", and "accidents with turning vehicle(s) or crossing paths in junctions" (the second and third most prevalent accident scenarios, respectively). The pre-crash systems addressed in ASSESS propose to yield beneficial safety outcomes with specific regard to these accident scenarios. This indicates that the ASSESS project is highly relevant to the current casualty crash problem. In the second stage of the analysis a selection of these accident scenarios were analysed further to define the accident parameters at a more detailed level .This paper describes the analysis approach and results from the first analysis stage.
The SafetyNet project was formulated in part to address the need for safety oriented European road accident data. One of the main tasks included within the project was the development of a methodology for better understanding of accident causation together with the development of an associated database involving data obtained from on-scene or "nearly onscene" accident investigations. Information from these investigations was complemented by data from follow-up interviews with crash participants to determine critical events and contributory factors to the accident occurrence. A method for classification of accident contributing factors, known as DREAM 3.0, was developed and tested in conjunction with the SafetyNet activities. Collection of data and case analysis for some 1 000 individual crashes have recently been completed and inserted into the database and therefore aggregation analyses of the data are now being undertaken. This paper describes the methodology development, an overview of the database and the initial aggregation analyses.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
The objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria and limits for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configurations such as impacts with car sides, trucks, and pedestrians. The WG consists of national government representatives who are supported by industrial advisers. The WG serves as a focal point for European research conducted by national and industry sponsored projects. The WG is responsible for collating the results from this research to achieve its objectives. EEVC WG 15 serves as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the Development of Crash Test Procedures"(VC-COMPAT) project partly funded by the European Commission. This paper presents a review of the current European research status. It also identifies current issues with candidate test procedures and lists the parameters that should be considered in assessing compatibility. The current candidate test procedures are: an offset barrier test with the progressive deformable barrier (PDB) face; a full width wall test with or without a deformable aluminium honeycomb face and a high resolution load cell wall; an offset barrier test with the EEVC barrier and load cell wall. These candidate test procedures must allow assessment of structural interaction, frontal force levels and compartment strength. The WG will report its findings to the EEVC Steering Committee and propose a test procedure in November 2006.
Bewertung der Fahrzeug-Fußraumintrusionen beim Offset Frontaltest gegen das Verformungselement
(1998)
In den Tests nach dem neuen Frontaltestverfahren (Entwürfe ECE R.94 sowie Richtlinie 96/79/EG und Ergänzung zu RL 70/156/EWG) entstehen hohe Verformungen der Fußräume der Versuchsfahrzeuge. Die Bewertung der Gefährdung der Insassen durch Intrusion, vorwiegend der Spritzwand begleitet von heftigen Bewegungen der Pedale, soll durch am Dummy zu messende Schutzkriterien erfolgen. Es ist vorgesehen, an den Dummies die Verschiebung des Schienbeins gegen das Knie, die Längskraft im Unterschenkel und den sogenannten Tibia Index zu messen. Um dieses zu ermöglichen, mussten an den vorhandenen Dummy-Unterschenkeln konstruktive Änderungen vorgenommen werden. Über die Herleitung der Schutzkriterien, Fragen bei der Anwendung dieser Kriterien sowie die technischen Einzelheiten und die Zertifizierung der neuen Dummy-Unterschenkel, welche die erforderlichen Messungen erlauben, wird berichtet.
The main focus of the benefit estimation of advanced safety systems with a warning interface by simulation is on the driver. The driver is the only link between the algorithm of the safety system and the vehicle, which makes the setup of a driver model for such simulations very important. This paper describes an approach for the use of a statistical driver model in simulation. It also gives an outlook on further work on this topic. The build-up process of the model suffices with a distribution of reaction times and a distribution of reaction intensities. Both were combined in different scenarios for every driver. Each scenario has then a specific probability to occur. To use the statistical driver model, every accident scene has to be simulated with each driver scenario (combinations of reaction times and intensities). The results of the simulations are then combined regarding the probabilities to occur, which leads to an overall estimated benefit of the specific system. The model works with one or more equipped participants and delivers a range for the benefit of advanced safety systems with warning interfaces.
Millions of kilometers are driven and recorded by car manufacturers and researchers every year to gather information about realistic traffic situations. The focus of these studies is often the recording of critical situations to create test scenarios for the development of new systems before introducing them into the market. This paper shows a novel Analysis and Investigation Method for All Traffic Scenarios (AIMATS) based on real traffic scenes. It also shows how to get detailed information about speeds, trajectories and behavior of all participants without driving thousands of kilometers at the example of conflict situations with animals. Basis of the AIMATS is the identification of the most relevant locations as "Points of Interest" (POI), the recording of the critical situations and their "base lines" at these POI. This paper presents a new method to identify critical scenarios involving both vehicles and animals as well as preliminary results of a study done in Saxony using this new method.
The focus of the technical innovation in the automobile industry is currently changing to sensor based safety systems, which are operating in the pre-crash phase of an accident. To get more information about this pre-crash phase for real accidents a simulation of this phase using the GIDAS database is done. The basics for this simulation are geometrical information about the accident location and the exact accident data out of the GIDAS database. This aggregated information gives the possibility to simulate an exact motion for every accident participant, using MATLAB / SIMULINK, in the pre-crash phase. After the simulation the information about the geometrical positions, the velocities and maneuvers of the drivers to an individual TTC (time to collision) are available. With those results it is possible to develop new useful sensor geometries using pre-crash scatter plots or estimate the efficiency of implemented active safety systems in combination with sensor characteristics. This simulation can be done for every reconstructed accident included in the GIDAS database, so these results can represent a wide spread basis for the further development of active safety systems and sensor geometries and characteristics
Entgegen populären Meinungen, welche älteren Kraftfahrern ein generelles Gefahrenpotenzial für die allgemeine Verkehrssicherheit zuschreiben, weisen die Unfallstatistiken eher auf eine besondere Gefährdung dieser Gruppe von Verkehrsteilnehmern hin, woraus sich Forderungen nach einer zielgruppenspezifischen Verkehrssicherheitsarbeit begründen. Kompetentes und damit sicheres Verhalten kann als Ergebnis der Passung zwischen den individuell verfügbaren Ressourcen und den Anforderungen der Umwelt betrachtet werden. Überschreiten die Umweltanforderungen die Verhaltenspotenziale des Individuums, kann es zu Überforderung kommen. Verdeutlichen lässt sich diese Perspektive durch genaue Betrachtung von Verkehrsunfällen unter Beteiligung älterer Kraftfahrer: So spiegeln die aktuellen Unfallstatistiken aus 2008 wider, dass ein großer Teil der Unfälle von Kraftfahrern im Alter über 65 Jahren auf sogenanntes Fehlverhalten in Knoten, wie z.B. Fehler beim Abbiegen, Ein- und Ausfahren in Kreuzungen und Vorfahrtbeachtung, zurückzuführen sind. Diese im Vergleich zu jüngeren Fahrern häufigere Verwicklung Älterer in Unfälle dieser Art legt nahe, dass es in genau diesen Situationen zu einem Ungleichgewicht zwischen individuell verfügbaren Ressourcen und den Anforderungen der Verkehrsumwelt kommt. Beispielsweise könnten in diesen Situationen Beeinträchtigungen der visuellen Wahrnehmungsfähigkeit, verlangsamte Reaktionszeiten oder auch Einschränkungen der Bewegungsausführung zu einer zu langsamen oder auch falschen Entscheidungsfindung oder Handlungsausführung im Straßenverkehr führen. Dieser Perspektive folgend können Maßnahmen zur Erhöhung der Verkehrssicherheit älterer Kraftfahrer zum einen auf Seiten des Individuums ansetzen und dazu beitragen, die Kompetenzen des älteren Kraftfahrers zu erhöhen, zum anderen Bezug auf den Kontext nehmen, indem durch Anpassungen der Bedingungen der Verkehrsumwelt zur Sicherheit " nicht nur " älterer Kraftfahrer beigetragen wird. Personenzentrierte Ansätze zielen dabei auf die Ausschöpfung der individuellen Potenziale zur Aufrechterhaltung, Verbesserung oder auch Wiederherstellung einer sicheren Verkehrsteilnahme bis ins hohe Lebensalter. Diese Ansätze umfassen Trainings- und Rehabilitationsprogramme der Fahrkompetenz gleichermaßen wie verkehrspädagogische Programme, mediale Informationskampagnen oder auch Beratungsmaßnahmen und Screening-Tests. Eine Schlüsselposition kann in diesem Kontext dem (Haus)-Arzt als Experten hinsichtlich Konstitution und Lebensverhältnissen seines Patienten und Vertrauensperson zukommen. In der Regel passen ältere Kraftfahrer ihr Fahrverhalten ihren individuell verfügbaren Kompetenzen an. Auf diese Weise können altersbegleitende oder auch mit Erkrankungen oder Medikamenteneinnahmen einhergehende Veränderungen der körperlichen oder geistigen Leistungsfähigkeit zumeist erfolgreich kompensiert werden. Personenzentrierten Ansätzen kommt jedoch eine besondere Relevanz für den kleinen Anteil älterer Fahrer zu, welche keine oder nur unzureichende Kompensation aufweisen. Kontextorientierte Ansätze beziehen sich auf Maßnahmen, welche eine möglichst optimale Gestaltung der Bedingungen der Verkehrsumwelt auf die Bedürfnisse und Anforderungen älterer Kraftfahrer herbeiführen sollen. Maßnahmen dieser Art zielen zum Beispiel auf eine Entschleunigung des Straßenverkehrs durch Geschwindigkeitsbegrenzungen oder auch bauliche Maßnahmen. Auch die Potenziale moderner Fahrzeugtechnik werden unter dieser Perspektive zur Erhöhung der Verkehrssicherheit älterer Fahrer nutzbar. So können Fahrerassistenz- oder Fahrerinformationssysteme den älteren Fahrer in komplexen Situationen unterstützen. Dabei ist der Nutzen für die Verkehrssicherheit jedoch stark von der Handhabbarkeit und Bedienqualität der technischen Hilfsmittel abhängig. Technologien, welche die Komplexität der Fahrzeugbedienung erheblich erhöhen oder die Aufmerksamkeit vom Straßenverkehr ablenken, können ggf. auch zu einer weiteren Diskrepanz zwischen Anforderungssituation und verfügbaren Kompetenzen beitragen. Neben diesen eher auf die individuelle Verkehrsteilnahme als Autofahrer bezogenen Maßnahmen sind weitere wichtige kontextorientierte Ansatzpunkte in alternativen Mobilitätsvarianten zum Auto, wie in der Verbesserung der Attraktivität von Angeboten des ÖPNV oder auch den Bedingungen für Fußgänger und Radfahrer, zu finden. In diesem Sinne erscheint ein mehrdimensionaler Ansatz für die Gestaltung von Maßnahmen zur Erhöhung der Verkehrssicherheit älterer Kraftfahrer am erfolgversprechendsten. Interventionsansätze sollten sich gegenseitig ergänzen und möglichst sowohl die Ressourcen auf Seiten des älteren Menschen selbst als auch der Umwelt umfassen.
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
In Deutschland werden als passive Schutzeinrichtungen an Straßen Stahlschutzplanken und in jüngerer Zeit auch vermehrt Betonschutzwände eingesetzt. Auf dem Gebiet der Schutzeinrichtungen wird es demnächst europäisch harmonisierte Normen geben. Durch ihre Einführung, vermutlich noch in 1997, kommt es auch in Deutschland zur Veränderung der Anforderungen an Schutzeinrichtungen. Die Qualifizierung der in Deutschland nach den Richtlinien für passive Schutzeinrichtungen an Straßen eingesetzten Schutzeinrichtungen nach den europäischen Vorgaben ist durch die Bundesanstalt für Straßenwesen (BASt) in einem Forschungsprojekt für das Bundesverkehrsministerium erfolgt. Die BASt hat ein weiteres Projekt initiiert mit dem Ziel, die wichtigsten Ausführungsformen zu untersuchen und zu weitergehenden Kenntnissen über die hier eingesetzten Schutzeinrichtungen zu kommen. Berichtet wird über wesentliche Ergebnisse aus diesem Projekt.
A set of recommendations for pan-European transparent and independent road accident investigations has been developed by the SafetyNet project. The aim of these recommendations is to pave the way for future EU scale accident investigation activities by setting out the necessary steps for establishing safety oriented road accident investigations in Member States. This can be seen as the start of the process for establishing road accident investigations throughout Europe which operate according to a common methodology. The recommendations propose a European Safety Oriented Road Accident Investigation Programme which sets out the procedures that need to be put in place to investigate a sample of every day road accidents. They address four sets of issues; institutional addressing the characteristics of the programme; operational describing the conditions under which data isrncollected; data storage and protection; and reports, countermeasures and the dissemination of data.rn
Road condition acquisition and assessment are the key to guarantee their permanent availability. In order to maintain a country's whole road network, millions of high-resolution images have to be analyzed annually. Currently, this requires cost and time excessive manual labor. We aim to automate this process to a high degree by applying deep neural networks. Such networks need a lot of data to be trained successfully, which are not publicly available at the moment. In this paper, we present the GAPs dataset, which is the first freely available pavement distress dataset of a size, large enough to train high-performing deep neural networks. It provides high quality images, recorded by a standardized process fulfilling German federal regulations, and detailed distress annotations. For the first time, this enables a fair comparison of research in this field. Furthermore, we present a first evaluation of the state of the art in pavement distress detection and an analysis of the effectiveness of state of the art regularization techniques on this dataset.
The national accident statistics demonstrate that the situation of passenger car side impacts is dominated by car to car accidents. Car side to pole impacts are relatively infrequent events. However the importance of car side to pole impacts is significantly increasing with fatal and seriously injured occupants. For the present study the German in-depth database GIDAS (German In-Depth-Accident Study) and the UK based database CCIS (Co-operative Crash Injury Study) were used. Two approaches were undertaken to better understand the scenario of car to pole impacts. The first part is a statistical analysis of passenger car side to pole impacts to describe the characteristics and their importance relevant to other types of impact and to get further knowledge about the main factors influencing the accident outcome. The second part contains a case by case review on passenger cars first registered 1998 onwards to further investigate this type of impact including regression analysis to assess the relationship between injury severity and pole impact relevant factors.
The role of a national motor vehicle crash causation study-style data set in rollover data analysis
(2010)
On 1 January 2005, The National Highway Traffic Safety Administration, an agency of the United States Department of Transportation, implemented a new data collection strategy designed to assess crash avoidance technologies and report associated behavioral inputs and outcomes. The original goal was a six-year program, however, during the shortened data collection period; it proved a valuable resource for understanding a precrash environment previously obscured by forensic case investigation. Another unintended consequence was an overlap with infrastructure, roadway geometry, and design with the occupant and vehicle outcomes, by virtue of well-defined attributes. External to the collected data, supplementary information was extrapolated, by using manuals published in the United States, by the American Association of State Highway Transportation Officials and selected State Departments of Transportation, in conjunction with the National Motor Vehicle Crash Causation Study (NMVCCS). This provided a backdrop to the infrastructure framework of the rollover problem within which the occupant and vehicle outcomes were studied. If a NMVCCS-style data collection were to be implemented elsewhere, then complementary manuals produced by federal transportation officials might be consulted producing similar relationships. The current study uses NMVCCS data to describe vehicles travelling through diverse design geometries and the outcome for occupants involved in crashes within that system. Codified and extrapolated data form the basis for assessing NMVCCS and its value to the transportation safety community, as the protocols are applicable universally. The benefit in continuing a NMVCCS-style study is noted, as the interaction of roadway infrastructure and occupant protection agencies might find paths to better work together in solving the complex rollover problem using a common data-driven approach.
Verkehrsunfallopfer, die beim Unfall überrollt werden, erleiden fast immer tödliche Verletzungen. Im innerstädtischen Bereich ereignen sich diese Unfälle mehrheitlich im niedrigen Geschwindigkeitsbereich. Die Frage der Vermeidbarkeit des Unfalls wird daher sehr oft seitens der Ermittlungsbehörde an die Sachverständigen gestellt. Im Rahmen der Unfallrekonstruktion spielt der Reifenprofilabdruck am Leichnam eine wichtige Rolle. Er belegt nicht nur den Überrollungsvorgang selbst, sondern erlaubt auch die Identifikation der Überrollungsrichtung und -region, aber auch des in Frage kommenden Reifens. Bei der retrospektiven Analyse von 120 Überrollungsfällen in Berlin (Fußgänger, Radfahrer und Kraftradfahrer) aus den letzten 23 Jahren wurde untersucht, wie verlässlich dieses Merkmal ist, wie oft und wo man es findet und von welchen Faktoren seine Entstehung beeinflusst wird.
To assess occupant safety in a crash test, criteria associating the measurements made with a crash test dummy to injury risk are necessary. To enable better protection of elderly car occupants the objective of this study was to develop improved thoracic injury criteria for the THOR average male dummy. The development of these criteria is usually based on matched dummy and Post Mortem Human Surrogate (PMHS) tests by relating the obtained PMHS injuries to dummy measurements. This approach is limited, since only a few tests in relevant loading conditions are available and any new test series requires high efforts to be performed due to their complexity and costs. To overcome these limitations and to extend the dataset for the development of THOR dummy chest injury risk functions a simulation-based approach was applied within the EC funded project SENIORS (Safety Enhanced Innovations For older Road Users - www.seniors-project.eu). Within this study frontal impact sled simulations with an FE model representing a THOR average male dummy and matched simulations with a human body model (HBM) representing an elderly car occupant were carried out. The HBM used for this study was the THUMS TUC with modified rib cage, which was developed in SENIORS. The modifications included material and geometry changes aiming to represent an elderly car occupant. The rib fracture risk was predicted with a deterministic approach whereby a rib was considered broken when the strain exceeded an age-dependent threshold. Furthermore, a probabilistic method was applied to predict the probability of sustaining a certain number of fractured ribs by comparing local strain values to the distribution of cortical rib ultimate strain. By relating the output from the HBM simulations to a multi-point dummy injury criterion, injury risk curves were calculated by statistical methods. The wide range of loading conditions resulted in the desired range of injuries and THOR ATD output. The number of fractured ribs predicted by the HBM based on the deterministic prediction method was between 0 and 15. Furthermore, the probabilistic risk for the number of rib fractures equal or greater than two, three or four was calculated for each load case. The THOR rib deflection criterion Rmax was between 18 and 56 mm, while the PC Score was in the range of 2.5 to 7.2. Based on these outputs new risk curves for the predicted deterministic (AIS2+/3+) and probabilistic injury risk were calculated. The new curves show reasonable shapes and significance that provide trust in their application. The new risk curves are compared to risk curves obtained by traditional methods. The results were found similar to previous injury risk functions based on physical tests, which gives a high level of confidence in the chosen approach. The simulation-based approach of matched ATD model vs. HBM simulation was successfully applied. Rmax curves show a slightly better quality than the injury criterion PC Score.