Conference Proceeding
Refine
Document Type
- Conference Proceeding (22) (remove)
Keywords
- Berechnung (22) (remove)
Institute
The German highway network hast o face new challenges in the near future, e.g. increasing traffic density and loads, climate change effects and new quality requirements regarding sustainability. It is necessary to come up with foresighted concepts in the present to be prepared for these challenges. Therefore it is important to adapt and enhance innovative attempts, which take changing impacts into account. One goal of these efforts is the development of adaptive systems for the provision of information and a holistic evaluation in real time. The paper describes the recent research and developments on a system for information and holistic evaluation in real time, taking into account sensor networks, evaluation procedures and their implementation in existing maintenance and inspection strategies.
Zunehmende Belastungen insbesondere der Bundesstraßen durch Schwerverkehr und Witterungsextreme führen dazu, dass viele Straßenabschnitte vor Ablauf der geplanten Nutzungsdauer erneuert werden müssen. Hinzu kommt die Herausforderung der Beseitigung von Investitionsstaus, das heißt die Erneuerung von Straßenabschnitten, deren substanzieller Zustand durch Überschreiten der geplanten Nutzungsdauer nicht mehr wirtschaftlich ist. Insbesondere bei extremen Witterungsbedingungen zeigen sich unter Umständen die Schwächen der verschiedenen Bauweisen. So kann es bei hohen Temperaturen und Stop-and-go-Verkehr bei Asphaltbauweisen zur erhöhten Spurrinnenbildung oder zur Schädigung der Längsnähte kommen. In der Betonbauweise können unter Umständen Hitzeschäden auftreten, wenn größere Imperfektionen – die direkt aus der Herstellung oder mangelnder/fehlerhafter Erhaltung resultieren – vorliegen. Aufgrund außergewöhnlicher klimatischer Situationen (Hitzeperioden) im Jahr 2013 kam es insbesondere im Bundesland Bayern zu einem vermehrten Auftreten von Hitzeschäden. Deshalb wurde im gleichen Jahr eine „Expertengruppe Hitzeschäden“ gegründet, die aus Vertretern des BMVI, der BASt, der Straßenbauverwaltungen und externer Experten bestand. Ziel war es, die Ursachen und Mechanismen von Hitzeschäden zu eruieren, um geeignete Maßnahmen zu deren Vermeidung ergreifen zu können. In diesem Zusammenhang wurde eine spezielle Messstation entwickelt, um die Temperatur über den Betondeckenquerschnitt, die Fugenbewegungen und weitere relevante Klimadaten ermitteln zu können. In enger Zusammenarbeit mit dem Bund und den Ländern wurden bisher 15 derartige Stationen aufgebaut. Somit besteht die Möglichkeit, in der Praxis auftretende witterungsinduzierte Spannungszustände im Kontext mit den verschiedenen Bauweisen sowie den zunehmend auftretenden Witterungsextrema zu analysieren. Die genaue Kenntnis über den Temperaturverlauf im Betonquerschnitt und zur Fugenbewegung, im zeitlichen und örtlichen Kontext zu den Witterungsbedingungen ist notwendig, um das Spannungsniveau im Deckensystem ableiten und prognostizieren zu können. Zudem ist die Kenntnis über konstruktive und materialtechnische Parameter aus dem zu betrachtenden Straßenoberbau erforderlich. Um Aussagen zur zeitlichen Entwicklung des Verhaltens des Plattensystems im Lebenszyklus treffen zu können, ist die kontinuierliche Erfassung, Speicherung und Analyse relevanter Daten von Bedeutung. Für die temporäre Spannungsprognose (z. B. über den Zeitraum einer Hitzeperiode) ist jedoch eine Analyse der Ausgangsdaten innerhalb weniger Stunden notwendig, um entsprechende Handlungsempfehlungen (z. B. Einrichtung von Tempolimits) treffen zu können. Durch die Verknüpfung mit weiteren Daten können ferner Aussagen zur Entwicklung wichtiger zeitlich veränderlicher Parameter über den Nutzungszeitraum gewonnen werden.
Die Kenntnis von Materialeigenschaften spielt bei der Entwicklung oder Optimierung von Betonen und Bauweisen für den Straßenbau sowie der Qualitätskontrolle und -sicherung eine bedeutende Rolle. Gleichermaßen bilden physikalische Materialkennwerte die Grundlage für die rechnerische Dimensionierung und die Restsubstanzbewertung von Betonfahrbahndecken. Einen relevanten Kennwert bei der Untersuchung thermisch induzierter Spannungs- und Verformungszustände stellt der thermische Ausdehnungskoeffizient von Beton dar. Dieser beeinflusst beispielsweise maßgeblich das Längsdehnungsverhalten des Deckensystems sowie das Ausmaß von Plattenkrümmungen und Fugenbewegungen. Im Zuge der systematischen Weiterentwicklung der rechnerischen Dimensionierung aber auch im Zusammenhang mit der gezielten Verbesserung der Gebrauchseigenschaften von Fahrbahndecken gilt es zu hinterfragen, ob lastunabhängige Formänderungseigenschaften, wie z. B. der thermische Ausdehnungskoeffizient der verwendeten Betone, aktuell ausreichend Beachtung finden, ob allgemeine Literaturwerte für die heutigen Fahrbandeckenbetone stets Gültigkeit besitzen und ob deren Implementierung in moderne Rechenmodelle zu validen Ergebnissen führt. Für eine empirische Herangehensweise ist die Verfügbarkeit adäquater Prüfverfahren von entscheidender Bedeutung. In Deutschland existiert aktuell jedoch kein standardisiertes oder genormtes Verfahren für die prüftechnische Bestimmung des thermischen Ausdehnungskoeffizienten von Beton. Daher wurden unter Beachtung straßenbauspezifischer Gesichtspunkte zwei Prüfansätze entwickelt, die in diesem Beitrag vorgestellt und hinsichtlich möglicher Messunsicherheiten und Messungenauigkeiten diskutiert werden. Außerdem erfolgt die Darstellung ausgewählter Ergebnisse aus Analysen an Bestandsbetonen aus dem BAB-Netz. Im Ergebnis sollen die Untersuchungen einen Beitrag zur Schaffung der prüftechnischen Voraussetzungen für eine abgesicherte Quantifzierung der thermischen Dehnung von Fahrbahndeckenbetonen leisten.
Knowledge of material properties is of great importance when developing new types of concrete and construction methods for road building, and for quality control and quality assurance. Physical material characteristics are likewise the basis for dimensioning and assessing the residual substance of concrete pavements. One relevant characteristic when examining thermally induced stress and deformation is the coefficient of thermal expansion (CTE) of concrete. This indicator, for example, significantly influences the longitudinal expansion of the pavement system as well as the degree of curling of slabs and joint movements. Extensive tests were conducted during the technical engineering assessment of the structural substance of concrete pavements in the German motorway network, including tests to determine the CTE of existing types of concrete. Because no standardised procedure currently exists in Germany for using tests to determine the CTE of concrete, the initial task was to develop a suitable test procedure from a road-building perspective, taking consideration of the national prevailing structural conditions. This article presents the results of selected status analyses, in which the CTE was determined for a total of 656 individual samples. The values calculated for the top and bottom drilled core layer are in the range 8.9 – 13.2 x 10-6/K, whereby the average CTE assumes a value of 10.7 x 10-6/K. The deviations of the CTEs from the bottom and top drilled core layer are in principle significantly below the limitation to a maximum of 2.50 x 10-6/K recommended in literature.
Mobility is a central requirement for economic growth, employment and participation of each individual in social life. This basic principle of the BMVI (Federal Ministry of Transport and Digital Infrastructure) requires an intact and functional infrastructure. In a context of increasing investments over the next few years, it will be relevant to develop a network related systematic procedure to be part of the structural maintenance of the federal highway network. In the planning of maintenance measures, the knowledge about the state of structural performance and its long-term development is of central importance. In the following, a method is presented which allows the mechanically and statistically reliable assessment and prognosis of structural performance of concrete pavements. In addition, the application and procedure are applied to a case study.
Ziel der Forschungsarbeiten zum Thema Durchsickerung von Straßenböschungen ist es, ausgewogene Beurteilungskriterien für einen umwelteffizienten und zugleich ökonomischen Einsatz von Ersatzbaustoffen und Bodenmaterial zu schaffen. Durch eine belastbare Datengrundlage zur Erfassung des Wasserhaushaltes des gesamten Bauwerkes können Instrumente entwickelt werden, um die Wirksamkeit der unterschiedlichen technischen Sicherungsmaßnahmen zu beurteilen. Um dieses Ziel zu erreichen, verfolgt die Bundesanstalt für Straßenwesen verschiedene Projektansätze zum Thema Durchsickerung von Straßenböschungen. Jeder Projektansatz hat seine Stärken und Schwächen. Durch großmaßstäbliche Versuche können die realen Verhältnisse gut wiedergegeben werden. Solche Versuche sind jedoch personalintensiv und langwierig. Schneller und preisgünstiger sind Modellrechnungen. Die Qualität der Berechnungen hängt aber stark von der Qualität der gewählten Parameter ab. Durch inverse Modellierung müssen die Eingabeparameter der Programme zur Modellrechnung an die Realität angepasst werden. Die realen Bedingungen werden am besten durch ein Pilotprojekt an einem realen Versuchsdamm wiedergegeben. Diese Versuche sind sehr aufwendig und sehr kostenintensiv, aber zur Validierung der Modellrechnung und der großmaßstäblichen Versuche erforderlich. In dem Betrag wird beschrieben, welche großmaßstäblichen Versuche durch die Bundesanstalt für Straßenwesen (BASt) durchgeführt wurden und wie sie von Anfang an durch Simulationsrechnungen begleitet wurden.
To assess occupant safety in a crash test, criteria associating the measurements made with a crash test dummy to injury risk are necessary. To enable better protection of elderly car occupants the objective of this study was to develop improved thoracic injury criteria for the THOR average male dummy. The development of these criteria is usually based on matched dummy and Post Mortem Human Surrogate (PMHS) tests by relating the obtained PMHS injuries to dummy measurements. This approach is limited, since only a few tests in relevant loading conditions are available and any new test series requires high efforts to be performed due to their complexity and costs. To overcome these limitations and to extend the dataset for the development of THOR dummy chest injury risk functions a simulation-based approach was applied within the EC funded project SENIORS (Safety Enhanced Innovations For older Road Users - www.seniors-project.eu). Within this study frontal impact sled simulations with an FE model representing a THOR average male dummy and matched simulations with a human body model (HBM) representing an elderly car occupant were carried out. The HBM used for this study was the THUMS TUC with modified rib cage, which was developed in SENIORS. The modifications included material and geometry changes aiming to represent an elderly car occupant. The rib fracture risk was predicted with a deterministic approach whereby a rib was considered broken when the strain exceeded an age-dependent threshold. Furthermore, a probabilistic method was applied to predict the probability of sustaining a certain number of fractured ribs by comparing local strain values to the distribution of cortical rib ultimate strain. By relating the output from the HBM simulations to a multi-point dummy injury criterion, injury risk curves were calculated by statistical methods. The wide range of loading conditions resulted in the desired range of injuries and THOR ATD output. The number of fractured ribs predicted by the HBM based on the deterministic prediction method was between 0 and 15. Furthermore, the probabilistic risk for the number of rib fractures equal or greater than two, three or four was calculated for each load case. The THOR rib deflection criterion Rmax was between 18 and 56 mm, while the PC Score was in the range of 2.5 to 7.2. Based on these outputs new risk curves for the predicted deterministic (AIS2+/3+) and probabilistic injury risk were calculated. The new curves show reasonable shapes and significance that provide trust in their application. The new risk curves are compared to risk curves obtained by traditional methods. The results were found similar to previous injury risk functions based on physical tests, which gives a high level of confidence in the chosen approach. The simulation-based approach of matched ATD model vs. HBM simulation was successfully applied. Rmax curves show a slightly better quality than the injury criterion PC Score.
Rekonstruktion des Bestandsplans im Zuge der Nachrechnung der Brücke über die Leine bei Schwarmstedt
(2019)
Der aktuell im Rahmen der Nachrechnungsrichtlinie geforderte Nachweis von Tragfähigkeit, Gebrauchstauglichkeit und Ermüdung der Brückenbauwerke im Bestand der Länder und des Bundes stellt eine enorme Herausforderung dar. Insbesondere bei unvollständigen oder fehlenden Bestandsplänen der Bauwerke sind Maßnahmen erforderlich, um die erforderlichen Informationen zu beschaffen. Ein wirkgungsvolles Instrument könne hierfür die zerstörungsfreien Prüfverfahren des Bauwesens sein. In dem präsentierten Forschungsprojekt erfolgte die Rekonstruktion eines Bestandsplanes direkt auf die Anforderungen des mit der Nachrechnung beauftragten Ingenieurbüros. Darüber hinaus wurde der Entwurf eines Leitfadens erstellt, der im Falle von unvollständigen oder fehlenden Bestandsplänen die Grundlagen für die Beauftragung und Durchführung der Nachrechnung schafft.
In this study, the mean profile depth (MPD) that expresses roughness of road pavements was calculated using the road survey equipment vehicle and the calculated MPD was compared with the real number of traffic accidents. The analysis method used in this study was to classify the appropriate clustering in relation to traffic accidents using the K-means clustering and to compare this with the presence of traffic accidents via the MPDs to derive the result. K-means clustering was used in the analysis method and four clusters were found using the clustering analysis results. The center of each cluster was 0.627, 0.850, 1.118, and 1.237, respectively. The result of this study is expected to be utilized as foundational research in the traffic safety area.
Vorgestellt werden Ergebnisse aus der Untersuchung "Vergleich verschiedener Modellierungsprogramme zur Berechnung von Luftschadstoffen". Die Untersuchung wurde begleitend zu der Pilotstudie "NO2-Reduktion an Ti02-dotierten Lärmschutzwänden (LSW) an der A1" durchgeführt. Projektziel war der Vergleich von drei Ausbreitungsmodellen sowie die Auswahl eines geeigneten Modells für ein zu entwickelndes Online-Monitoring-System. Es wurde festgestellt, dass sich die Modellergebnisse infolge der Umsetzung kleinräumiger Details unterscheiden sowie dass alle Modelle lediglich geringe NOx-Minderungen in Folge der katalytischen Oberflächenbeschichtung anzeigen. In den numerischen Modellen wird die photokatalytische Wirkung der Ti02-beschichteten Lärmschutzwand über einen Depositionsprozess berücksichtigt. Unter Berücksichtigung der Hintergrundbelastung und der NOx-NO2-Umwandlung würde sich die Wirkung des Katalysators im Maximum auf weniger reduzieren. Die Messungen zeigten keine eindeutige Wirkung bezüglich der Immissionskonzentrationen im Bereich der beschichteten beziehungsweise unbeschichteten LSW an.
Vorgestellt werden Vorgehensweise, Datenaufbereitung, Modellaufbau und Ergebnisse des BASt-Projekts "Numerische Simulation der Stickoxidminderung durch photokatalytische Oberflächen an Verkehrswegen". Die Vorteile des Konzepts liegen in der Berücksichtigung von Zeitreihen (Eingangsdaten, Ausbreitungsrechnung) und in der Tatsache, dass die Depositionsgeschwindigkeit als zeitlich variable Eingangsgröße bei der Modellierung berücksichtigt wurde. Die Ergebnisse liegen entsprechend als Zeitreihen vor (Jahres- oder Tagesgänge können untersucht werden). Es ergab sich eine Minderung der NO2-Belastung um maximal knapp 1.5% im Nahbereich der Lärmschutzwand. Wesentlicher Faktor bei der Wirksamkeit photokatalytischer Oberflächen ist die Interaktion zwischen Gesamtbelastung und Depositionsgeschwindigkeit im Tagesverlauf.
The Traffic Accident Research Institute at University of Technology Dresden investigates about 1,000 accidents annually in the area around and in Dresden. These datasets have been summarized and evaluated in the GIDAS (German Accident In-Depth Study) project for 13 years. During the project it became apparent that the specific traffic situation of a covert exit of a passenger car and an intersecting two-wheeler involves a high risk potential. This critical situation develops in a large part due to the lack of visibility between the driver and the intersecting bike. In this paper the accident avoidance potential of front camera systems with lateral field of view, which allows the driver to have an indirect sight into the crossing street area will be presented.
This study aimed at comparing head Wrap Around Distance (WAD) of Vulnerable Road User (VRU) obtained from the German in-depth Accident Database (GIDAS), the China in-depth Accident Database (CIDAS) and the Japanese in-depth Accident Database (ITARDA micro). Cumulative distribution of WAD of pedestrian and cyclist were obtained for each database (AIS2+) showing that WAD of cyclists were larger than the ones of pedestrians. Comparing three regions, the 50%tile WAD of GIDAS was larger than that of both Asian accident databases. Using linear regression that might predict WAD of pedestrians and cyclists from Impact speed and VRU height, WADs were calculated to be 206cm/219cm (Pedestrian/Cyclist) for GIDAS, 170cm/192cm for CIDAS and 211cm/235cm for ITARDA. In addition, this study may be helpful for reconsideration of WAD measurement alignment between accident reconstruction and test procedures.
The declining trend since 1991 in the number of killed people was broken in 2011 when overall 4 009 people died in traffic accidents in Germany. The question arises if there is a stagnating trend of fatalities in Germany in future? By breaking down the accidents with casualties towards a monthly view one can see a decreasing trend of fatalities in the warmer months especially since 2009. When comparing against winter months higher deviations are observed. In December 2011 an increase of 191 traffic deaths were registered (181 in 2010 compared to 372 in 2011). Further analyses of different accident influences were evaluated and their possibility of drastic change from one year to the other was determined. As seen weather- and environmental conditions are one of the major contributing factors and are one of the causes for the increased number of fatalities. To support the underlying assumption a model had been created to calculate the number of traffic deaths on a daily basis approach. As an input, road conditions projected through weather parameters and also different driving behaviors on weekdays or holidays were used. As a result, estimates of daily fatality with up to 75% precision can be achieved out of the 2009, 2010 and 2011 data. Further on it shows that weather and street conditions have a high influence on the overall resulting number of traffic accidents with casualties, and especially to the number of fatalities. Hence it is estimated that approximately 3 300 people were killed in traffic accidents in Germany in 2013 which would be again a reduction of another 13% compared to 2012. Therefore an answer to the question will be that the decreasing trend in traffic fatalities in Germany somehow is not broken when environmental conditions are included in national statistics. Their effects will become more visible in future accident statistics and it is estimated variances of 5% to 8% of the annual number of traffic fatalities in Germany will be seen.
For the estimation of the benefit and effect of innovative Driver Assistance Systems (DAS) on the collision positions and by association on the accident severity, together with the economic benefit, it becomes necessary to simulate and evaluate a variety of virtual accidents with different start values (e.g. initial speed). Taken into account the effort necessary for a manual reconstruction, only an automated crash computation can be considered for this task. This paper explains the development of an automated crash computation based on GIDAS. The focus will be on the design of the virtual vehicle models, the method of the crash computation as well as exemplary applications of the automated crash computation. For the first time an automated crash computation of passenger car accidents has been realized. Using the automated crash computation different tasks within the field of vehicle safety can be elaborated. This includes, for example, the calculation of specific accident parameters (such as EES or delta-V) for various accident constellations and the estimation of the economic benefit of DAS using IRFs (Injury Risk Functions).
The evaluation of the expected benefit of active safety systems or even ideas of future systems is challenging because this has to be done prospectively. Beside acceptance, the predicted real-world benefit of active safety systems is one of the most important and interesting measures. Therefore, appropriate methods should be used that meet the requirements concerning representativeness, robustness and accuracy. The paper presents the development of a methodology for the assessment of current and future vehicle safety systems. The variety of systems requires several tools and methods and thus, a common tool box was created. This toolbox consists of different levels, regarding different aspects like data sources, scenarios, representativeness, measures like pre-crash-simulations, automated crash computation, single-case-analyses or driving simulator studies. Finally, the benefit of the system(s) is calculated, e.g. by using injury risk functions; giving the number of avoided/mitigated accidents, the reduction of injured or killed persons or the decrease of economic costs.
Um ein zuverlässiges Straßennetz aufrechtzuerhalten, ist es notwendig, neue innovative Ansätze in das Erhaltungsmanagement der Brückenbauwerke im Bundesfernstraßennetz zu integrieren und weiterzuentwickeln. Ergänzend zu den turnusmäßigen Bauwerksprüfungen nach DIN 1076 wird daher ein adaptives Konzept bereitgestellt, das es ermöglichen soll zum einen Zustandsveränderungen frühzeitig zu erfassen und zu bewerten und zum anderen mit Hilfe von erfassten Einwirkungen und Widerständen zukünftige Zustandsentwicklungen zu prognostizieren. Die zu konzipierenden Systeme setzen sich im Wesentlichen aus der Datenerfassung mit Hilfe von Sensorik und den zur echtzeitnahen Verwendung und Bewertung notwendigen Modellen zusammen. Im Rahmen mehrerer Forschungsprojekte wurden einzelne Bausteine eines solchen adaptiven Systems erarbeitet.
The GIDAS-investigation team of Dresden (VUFO) has documented more than 11.500 accidents since 1999. The documentation of the accident includes beside vehicle-, injury- and environmental-data very detailed reconstruction data. Within this accident investigation the VUFO began to record the skid resistance of the accident site in 2009. The measurements are divided in macro- and microroughness (Sand depth method and Portable Skid Resistance Tester-SRT-by Munro-Stanley London-©). Both methods are used to determine the skid resistance for more than 1000 passenger cars. The aim of the present study is to find out a relationship between the measured skid resistance, the road conditions and the friction coefficient, which is used to calculate the maximum accelerations and decelerations during a reconstruction of an accident. Basic approach to convert the SRT-value into the friction coefficient is the calculation of the theoretical absorbed energy of the spring rubber system of the swinging arm of lever. This absorbed energy is used to get the friction coefficient by using the equations for the work of friction. To consider the road-behavior, in correlation to the friction coefficient, the results will be merged with existing literature. Last step for this study will be a comparison between actual used friction coefficients all over the GIDAS-database and the theoretical results. The study shows, if it is possible to use the SRT-Measurement for the estimation of a friction coefficient for the reconstruction of a traffic accident. As expected, the GIDAS-Database and the additional measurement of the roughness of the road directly on the spot are an enormous useful dataset.
A total survey of road traffic accidents involving most severely injured, defined as sustaining a polytrauma or severe monotrauma (ISS > 15) or being killed, was conducted over 14 months in a large study region in Germany. Data on injuries, pre-clinical and clinical care, crash circumstances and vehicle damage were obtained both prospectively and retrospectively from trauma centers, dispatch centers, police and fire departments. 149 patients with a polytrauma and eight with a severe monotrauma were recorded altogether. 22 patients died in hospital. Another 76 victims had deceased at the accident scene. In 2008, 49 % of patients treated with life-threatening injuries were car or van occupants, 21 % motorcyclists, 18 % cyclists and 10 % pedestrians. Among fatalities at the scene, vehicle occupants constituted an even larger portion. The number of road users with life-threatening trauma in the region was extrapolated to the German situation. It suggests that 10 % among the "seriously injured" as defined in national accident statistics are surviving accident victims with a polytrauma or severe monotrauma.
This study that was funded by the Research Association for Automotive Technology (FAT) develops a method for the evaluation of the placement of tanks or batteries by using the deformation frequencies in real-world accidents. Therefore, the deformations of more than 20.000 passenger cars in the GIDAS database are analysed. For each vehicle a contour of deformation is calculated and the deformed areas of the vehicles are transferred in a rangy matrix of deformation. Thereby, the vehicle is divided into more than 190.000 cells. Afterwards, all single matrices of deformation are summarized for each cell which allows representative analyses of the deformation frequencies of accidents with passenger cars in Germany. On the basis of these deformation frequencies it is possible to determine least deformed areas of all passenger cars. Furthermore, intended placements of tanks or batteries can be estimated in an early stage of development. Therefore, all vehicles with deformations in the intended tank areas can be analysed individually. Considering numerous parameters out of the GIDAS database (e.g. collision speed, kind of accident, overlap, collision partner etc.) the occurring forces can be calculated or the deformation frequency can be estimated. Furthermore, it is possible to consider the influence of primary and secondary safety systems on the deformation behaviour. The analysis of "worst case accident events" is an additional application of the calculated matrix of deformation frequency.
Mechanical properties of tibial bone at compressive strain rates of 50-200 s-1 are obtained through Split Hopkinson pressure bar. Cylindrical specimens of 12-15 mm diameter and 2-5 mm thickness were used. The Young- moduli are calculated from linear portion of stress-strain curves. For both cortical and cancellous part of the bones, the Young- modulus was found to increase with the increasing strain rates. Also for both cancellous and cortical bones the Young- modulus increases consistently with increase in densities.
Im Beitrag wird über Rissbildungen in orthotropen Fahrbahnplatten, die im "Schubzahn" des Querträgerstegblechs von den Anschlussschweissnähten trapezförmiger Längsträger ausgehen, berichtet. Der Rissausgangspunkt liegt im Bereich der Ausnehmung des Querträgersteges für die durchlaufenden Längsträger. Durch Optimierung der Querträgerausnehmung und örtliche Verstärkung (Aufpflasterung) des Querträgerstegblechs im Bereich des Schubzahnes soll eine dauerhafte Instandsetzung der aufgetretenen Schäden ermöglicht werden. Durch genauere numerische und versuchstechnische Untersuchungen soll diese Aussage untermauert werden. Einzelheiten der bereits durchgeführten Untersuchungen werden mitgeteilt.