Wissenschaftlicher Artikel
Filtern
Erscheinungsjahr
Dokumenttyp
- Wissenschaftlicher Artikel (48) (entfernen)
Sprache
- Deutsch (32)
- Englisch (15)
- Mehrsprachig (1)
Schlagworte
- Safety (15)
- Sicherheit (15)
- Bewertung (11)
- Fahrzeug (11)
- Test (11)
- Vehicle (11)
- Versuch (11)
- Evaluation (assessment) (10)
- Fahrzeugführung (10)
- Driver information (9)
Institut
- Abteilung Fahrzeugtechnik (48) (entfernen)
Autonomous Emergency Braking (AEB) systems for pedestrians have been predicted to offer substantial benefit. On this basis, consumer rating programmes, e.g. Euro NCAP, are developing rating schemes to encourage fitment of these systems. One of the questions that needs to be answered to do this fully, is to determine how the assessment of the speed reduction offered by the AEB is integrated with the current assessment of the passive safety for mitigation of pedestrian injury. Ideally, this should be done on a benefit related basis. The objective of this research was to develop a benefit based methodology for assessment of integrated pedestrian protection systems with pre-crash braking and passive safety components. A methodology has been developed which calculates the cost of pedestrian injury expected, assuming all pedestrians in the target population (i.e. pedestrians impacted by the front of a passenger car) are impacted by the car being assessed, taking into account the impact speed reduction offered by the car’s AEB (if fitted) and the passive safety protection offered by the car’s frontal structure. For rating purposes, this cost can be normalised by comparing it to the cost calculated for selected cars. The methodology uses the speed reductions measured in AEB tests to determine the speed at which each casualty in the target population will be impacted. The injury to each casualty is then calculated using the results from standard Euro NCAP pedestrian impactor tests and injury risk curves. This injury is converted into cost using ‘Harm’ type costs for the body regions tested. These costs are weighted and summed. Weighting factors were determined using accident data from Germany and GB and the results of a benefit analysis performed by the EU FP7 AsPeCSS project. This resulted in German and GB versions of the methodology. The methodology was used to assess cars with good, average and poor Euro NCAP pedestrian ratings, with and without a current AEB system fitted. It was found that the decrease in casualty injury cost achieved by fitting an AEB system was approximately equivalent to that achieved by increasing the passive safety rating from poor to average. Also, it was found that the assessment was influenced strongly by the level of head protection offered in the scuttle and windscreen area because this is where head impact occurs for a large proportion of casualties. The major limitation within the methodology is the assumption used implicitly during weighting. This is that the cost of casualty injuries to body areas, such as the thorax, not assessed by the headform and legform impactors, and other casualty injuries such as those caused by ground impact, are related linearly to the cost of casualty injuries assessed by the impactors. A methodology for assessment of integrated pedestrian protection systems was developed. This methodology is of interest to consumer rating programmes which wish to include assessment of these systems. It also raises the interesting issue if the head impact test area should be weighted to reflect better real-world benefit.
Effects of time pressure on left-turn decisions of elderly drivers in a fixed-base driving simulator
(2019)
In countries with right lane traffic left-turn maneuvers at intersections are known to be particularly critical for elderly drivers. It has been suggested that the implementation and use of Advanced Driver Assistance Systems (ADAS) might offer a solution to compensate for age-related weaknesses in driving-related skills. In the present paper an experiment is reported which explored the effects of time pressure on the performance of left-turn manoeuvers supported by an ADAS function (time gap assistant). The study was performed in a fixed-base driving simulator with 20 younger (22-37) and 21 elderly drivers (60-84) who were observed when negotiating left-turn manoeuvers on rural roads with and without the assistance function active. Subjects performed the task once under conditions of time pressure once without. Results indicate that both age groups used the assistance function to perform the left-turn manoeuvers with shorter time gaps. Under conditions of time pressure this effect was more pronounced, and the effects of time pressure were stronger for the elderly. However, there were only weak indications for a specific benefit of the assistance function for the elderly.
Although cruise control (CC) is available for most cars, no studies have been found which examine how this automation system influences driving behaviour. However, a relatively large number of studies have examined adaptive cruise control (ACC) which compared to CC includes also a distance control. Besides positive effects with regard to a better compliance to speed limits, there are also indications of smaller distances to lead vehicles and slower responses in situations that require immediate braking. Similar effects can be expected for CC as this system takes over longitudinal control as well. To test this hypothesis, a simulator study was conducted at the German Aerospace Center. Twenty-two participants drove different routes (highway and motorway) under three different conditions (assisted by ACC, CC and manual driving without any system). Different driving scenarios were examined including a secondary task condition. On the one hand, both systems lead to lower maximum velocities and less speed limit violations. There was no indication that drivers shift more of their attention towards secondary tasks when driving with CC or ACC. However, there were delayed driver reactions in critical situations, e.g., in a narrow curve or a fog bank. These results give rise to some caution regarding the safety effects of these systems, especially if in the future their range of functionality (e.g., ACC Stop-and-Go) is further increased.
Established in 1997, the European New Car Assessment Programme (Euro NCAP) provides consumers with a safety performance assessment for the majority of the most popular cars in Europe. Thanks to its rigorous crash tests, Euro NCAP has rapidly become an important driver safety improvement to new cars. After ten years of rating vehicles, Euro NCAP felt that a change was necessary to stay in tune with rapidly emerging driver assistance and crash avoidance systems and to respond to shifting priorities in road safety. A new overall rating system was introduced that combines the most important aspects of vehicle safety under a single star rating. The overall rating system has allowed Euro NCAP to continue to push for better fitment and higher performance for vehicles sold on the European market. In the coming years, the safety rating is expected to play an important role in the support of the roll-out of highly automated vehicles.
Estimation of the effects of new emission standards on motorcycle emissions by means of modeling
(2016)
Road traffic is, in addition to the energy sector and the industry, one main source of air pollution and carbon dioxide emissions. Although most countries and manufacturers agreed to environmental regulations to reduce the pollutant emissions, particularly in urban areas with high traffic density, the impact of road traffic emissions on the environment and human health has been growing in importance steadily. Due to stricter emission standards and the binding use of emission-reducing systems (e.g. three-way catalyst) hydrocarbon emissions from passenger cars have been reduced significantly since the last two decades. Unlike to passenger cars the emissions standards of powered two-wheelers have not been adjusted since 2006 although their share of hydrocarbon emissions to the total amount of hydrocarbon emissions of road traffic is estimated to be disproportionately high. Due to the new regulation (EU) No. 168/2013 powered two-wheelers have to fulfill new emission standards from 2016 (Euro 4) and 2020 (Euro 5) onwards. Besides new limits for the tailpipe emissions the evaporative emissions are regulated separately for the first time, as they make up a high proportion to the total hydrocarbon emissions in this vehicle class. In this context, the calculation and forecast of road traffic emissions is an important tool to verify compliance of climate targets and to assess the reduction potential of emission-reducing systems. For that purpose the Federal Highway Research Institute (BASt) uses the emission- and calculation tool TREMOD (Transport Emission Model) which provides baseline data and calculated results for pollutants in almost every differentiation e.g. vehicle category, traffic situation and road type. Moreover, estimations of future emission trends, stock information and mileage distribution can be made. The main objective is to illustrate the impact of the upcoming emission standards Euro 4 and Euro 5 on the operational hydrocarbon emissions of powered two-wheelers based on statistical estimations. The significant aspect is to generate scenarios to show the reduction potential of hydrocarbon emissions of powered two-wheelers, differentiated into motorcycles and small motorcycles, in relation to the total share of hydrocarbon emissions in this vehicle class and to the total hydrocarbon emissions from road traffic. As a part of their research, the authors can make initial statements about the possible effect of the new emission standards of regulation (EU) No. 168/2013 by means of modeling with TREMOD.
There is considerable evidence for the negative effects of driver distraction on road safety. In many experimental studies, drivers have been primarily viewed as passive receivers of distraction. Thus, there is a lack of research on the mediating role of their self-regulatory behavior. The aim of the current study was to compare drivers' performance when engaged in a system-paced secondary task with a self-paced version of this task and how both differed from baseline driving performance without distraction. Thirty-nine participants drove in a simulator while performing a secondary visual"manual task. One group of drivers had to work on this task in predefined situations under time pressure, whereas the other group was free to decide when to work on the secondary task (self-regulation group). Drivers' performance (e.g., lateral and longitudinal control, brake reaction times) was also compared with a baseline condition without any secondary task. For the system-paced secondary task, distraction was associated with high decrements in driving performance (especially in keeping the lateral position). No effects were found for the number of collisions, probably because of the lower driving speeds while distracted (compensatory behavior). For the self-regulation group, only small impairments in driving performance were found. Drivers engaged less in the secondary task during foreseeable demanding or critical driving situations. Overall, drivers in the self-regulation group were able to anticipate the demands of different traffic situations and to adapt their engagement in the secondary task, so that only small impairments in driving performance occurred. Because in real traffic drivers are mostly free to decide when to engage in secondary tasks, it can be concluded that self-regulation should be considered in driver distraction research to ensure ecological validity.
The goal of the project FIMCAR (Frontal Impact and Compatibility Assessment Research) was to define an integrated set of test procedures and associated metrics to assess a vehicle's frontal impact protection, which includes self- and partner-protection. For the development of the set, two different full-width tests (full-width deformable barrier [FWDB] test, full-width rigid barrier test) and three different offset tests (offset deformable barrier [ODB] test, progressive deformable barrier [PDB] test, moveable deformable barrier with the PDB barrier face [MPDB] test) have been investigated. Different compatibility assessment procedures were analysed and metrics for assessing structural interaction (structural alignment, vertical and horizontal load spreading) as well as several promising metrics for the PDB/MPDB barrier were developed. The final assessment approach consists of a combination of the most suitable full-width and offset tests. For the full-width test (FWDB), a metric was developed to address structural alignment based on load cell wall information in the first 40 ms of the test. For the offset test (ODB), the existing ECE R94 was chosen. Within the paper, an overview of the final assessment approach for the frontal impact test procedures and their development is given.
This paper presents findings of a laboratory experiment which aimed at evaluating the sensitivity and intrusiveness of Tactile Detection Response Task (TDRT) methodology. Various single-task, dual-task and triple-task scenarios were compared. The task scenarios included a surrogate of driving (tracking task) and different secondary tasks (N-back, surrogate reference task (SuRT)). The results suggest that the TDRT is sensitive to load levels of secondary tasks which primarily demand for cognitive resources (N-back). Sensitivity to variations of visual"manual load could not be shown (SuRT). TDRT seems also to be able to differentiate between modes of primary task which varies in terms of cognitive load (visual against auditory tracking task). Results indicated intrusiveness of TDRT on primary task performance and secondary task performance depending on the type of underlying task scenario. As a conclusion, TDRT can be recommended as a method to assess attentional effects of cognitive load of a secondary task, but should be used with caution for secondary tasks with strong motor demands.
Die Initiative der Einführung kooperativer Systeme in einem Korridor von Rotterdam über Frankfurt/Main nach Wien, dem sogenannten C-ITS Corridor, und damit auch in Deutschland wurde im Juni 2013 durch die Unterzeichnung einer entsprechenden Absichtserklärung des Bundesministeriums für Verkehr, Bau und Stadtentwicklung mit den Verkehrsministern der Niederlande und Österreichs offiziell gestartet. In vielen Forschungsprojekten wurden vorher die Grundlagen erarbeitet, um eine solche Einführung technisch überhaupt erst möglich zu machen. Im Beitrag werden diese Ergebnisse nochmals kurz aufgegriffen und um den aktuellen Stand bei den Entwicklungen im C-ITS Corridor erweitert. Als erstes Einführungsszenario wurden die Baustellenwarnung und Kooperatives Verkehrsmanagement unter Einbeziehung von Fahrzeugdaten gewählt. Nicht verschwiegen werden sollen hierbei auch die wesentlichen Herausforderungen, die im Übergang von Forschung und Feldtests zu realen Anwendungen liegen.
Müdigkeit am Steuer ist eine bedeutsame Ursache von Straßenverkehrsunfällen. Es steht eine Fülle unterschiedlicher Methoden zur Verfügung, um Müdigkeit beim Fahrer zu erkennen. Ziel des vorliegenden Projekts war es, auf Basis einer mehrstufigen Befragung von zwölf Experten aus Industrie- und Hochschulforschung die Stärken und Schwächen der derzeit validesten objektiven Müdigkeitsmessverfahren vergleichend zu beschreiben. Als Basis der Bewertung diente ein eigens erarbeiteter Gütekriterienkatalog. Zu den validesten Müdigkeitsmessverfahren gehören aus Expertensicht Lenkverhalten und Spurhaltung, Indikatoren des Lidschlussverhaltens und des EEG, das videobasierte Expertenrating sowie der kontrovers diskutierte Pupillografische Schläfrigkeitstest. Die Güteprofile der sechs ausgewählten Messverfahren werden aufgeführt. Je nach Einsatzgebiet sind alle ausgewählten Messverfahren (Forschung und Entwicklung), nur einige (Müdigkeitswarnsystem im Fahrzeug), oder kein einziges (Verkehrskontrolle) geeignet. Dem Urteil der Experten nach bedarf eine valide Müdigkeitserfassung der Kombination von mindestens zwei Messverfahren unter Berücksichtigung der spezifischen Stärke-Schwächenprofile.
Economic constraints nowadays require transporting greater volumes of freight at lower cost. Yet, physical profiles of trucks do not all generate the same effects on road infrastructure for a given tonnage hauled. The objective then lies in finding an optimal service level that reduces the damage caused to infrastructure. Results derived for the impact of trucks on pavements are presented. The impact of truck traffic trends on road bridges will also be discussed.rn
Aus wissenschaftlichen Untersuchungen ist bekannt, dass ältere Menschen trotz ihrer langen Fahrerfahrung in spezifischen Verkehrssituationen Fahrfehler und Unsicherheiten zeigen. In zwei Experimenten an jüngeren und älteren Versuchsteilnehmern wurde im Ergonomie-Labor der Bundesanstalt für Straßenwesen (BASt) versucht, den Ursachen spezifischer Fahrfehler älterer Kraftfahrer nachzugehen. Die Ergebnisse lieferten wichtige Ansatzpunkte für die Entwicklung von Fahrerassistenzsystemen (FAS), indem Erkenntnisse zu visuellen Aufmerksamkeitsleistungen gesammelt wurden. Im Rahmen eines Doppeltätigkeitsparadigmas wurde der visuell-räumliche Aufmerksamkeitsprozess, der für das Führen von Kraftfahrzeugen von wesentlicher Bedeutung ist, nicht nur auf der Verhaltensebene, sondern auch neurophysiologisch durch die Ableitung der Hirnströme mittels EEG untersucht. Hauptaufgabe war in beiden Experimenten eine Spurhalteaufgabe, die kurvenreiches Fahren simulieren sollte. Nebenaufgabe war jeweils eine Lichtreizaufgabe, bei der so schnell wie möglich durch Tastendruck auf einen Lichtreiz reagiert werden musste. Im zweiten Experiment wurde überprüft, ob bei der Lichtreizaufgabe die Verschlechterung der Aufmerksamkeitsleistung graduell erfolgt, indem bei den Lichtreizen die Exzentrizität erweitert wurde. Die Reize wurden bilateral, in abgestufter Form in verschiedenen Sehwinkeln von der Fovea centralis präsentiert. Dargestellt werden die Versuchsdurchführung sowie die Ergebnisse für die Verhaltensdaten und die festgestellten ereigniskorrelierten Potenziale (EKP). Es zeigte sich, dass durch die Berücksichtigung zusätzlicher weiterer Exzentrizitäten die Ergebnisse der Vorgängerstudie in bedeutsamer Weise erweitert werden konnten. Für beide Gruppen zeigten sich über den Verlauf hinweg klare Anzeichen für den Verlauf kompensatorischer Prozesse, die sich für die Älteren aber nur bis zu einem Sehwinkel von 50 Grad darstellten. Bei Reizen im Sehwinkel von 60 Grad war die Detektionsleistung deutlich schlechter, vor allem bei den älteren Versuchsteilnehmern. Außerdem wurde festgestellt, dass vor allem die Älteren Beeinträchtigungen in der Detektionsleistung zeigen, wenn der Abstand zwischen zwei Reizen gering ist. Es zeigt sich, das im Hinblick auf das Übersehen von Verkehrsobjekten, das eine wesentliche Ursache von Unfällen älterer Fahrer darstellt, diese technisch - beispielsweise bei Wende- oder Abbiegeprozessen - durch einen Sehfeldassistenten unterstützt werden können. Da Ältere durch schnelle Reaktionsabfolgen stärker beansprucht werden, sind Systeme mit Warnfunktion oder teilautomatisierte Systeme eher kritisch zu sehen, da sie zusätzlichen Bedien- beziehungsweise Überwachungsaufwand erfordern.
To improve vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility aims to improve both the self and partner protection properties of vehicles. Although compatibility has received worldwide attention for many years, no final assessment approach has been defined. Within the Frontal Impact and Compatibility Assessment Research (FIMCAR) project, different frontal impact test procedures (offset deformable barrier [ODB] test as currently used for Economic Commission for Europe [ECE] R94, progressive deformable barrier test as proposed by France for a new ECE regulation, moveable deformable barrier test as discussed worldwide, full-width rigid barrier test as used in Federal Motor Vehicle Safety Standard [FMVSS] 208, and full-width deformable barrier test) were analyzed regarding their potential for future frontal impact legislation. The research activities focused on car-to-car frontal impact accidents based on accident investigations involving newer cars. Test procedures were developed with both a crash test program and numerical simulations. The proposal from FIMCAR is to use a full-width test procedure with a deformable element and compatibility metrics in combination with the current offset test as a frontal impact assessment approach that also addresses compatibility. By adding a full-width test to the current ODB test it is possible to better address the issues of structural misalignment and injuries resulting from high acceleration accidents as observed in the current fleet. The estimated benefit ranges from a 5 to 12 percent reduction of fatalities and serious injuries resulting from frontal impact accidents. By using a deformable element in the full-width test, the test conditions are more representative of real-world situations with respect to acceleration pulse, restraint system triggering time, and deformation pattern of the front structure. The test results are therefore expected to better represent real-world performance of the tested car. Furthermore, the assessment of the structural alignment is more robust than in the rigid wall test.
Verschiedene Forschungsprojekte aus dem Bereich Kooperativer Systeme, die vor Kurzem gestartet sind, beschäftigen sich unter anderem mit den organisatorischen Aspekten einer Gesamtarchitektur. Eine Organisationsarchitektur beschreibt dabei die Rollen und Verantwortlichkeiten, die im Betrieb unterschiedlicher Kooperativer Anwendungen auftreten. In den Projekten erfolgt zumeist eine Betrachtung der Organisationsarchitektur anhand konkreter Implementierungsszenarien oder Use Cases. Der im Bericht dokumentierte aktuelle Stand der abstrakten Beschreibung der Rollen und Verantwortlichkeiten soll den Projekten und Initiativen als Diskussionsgrundlage und Ausgangspunkt für die Erarbeitung einer möglichen Organisationsarchitektur Kooperativer Systeme und deren Ausgestaltung dienen.
The strong prevalence of human error as a crash causation factor in motorcycle accidents calls for countermeasures that help tackling this issue. Advanced rider assistance systems pursue this goal, providing the riders with support and thus contributing to the prevention of crashes. However, the systems can only enhance riding safety if the riders use them. For this reason, acceptance is a decisive aspect to be considered in the development process of such systems. In order to be able to improve behavioural acceptance, the factors that influence the intention to use the system need to be identified. This paper examines the particularities of motorcycle riding and the characteristics of this user group that should be considered when predicting the acceptance of advanced rider assistance systems. Founded on theories predicting behavioural intention, the acceptance of technologies and the acceptance of driver support systems, a model on the acceptance of advanced rider assistance systems is proposed, including the perceived safety when riding without support, the interface design and the social norm as determinants of the usage intention. Since actual usage cannot be measured in the development stage of the systems, the willingness to have the system installed on the own motorcycle and the willingness to pay for the system are analyzed, constituting relevant conditions that allow for actual usage at a later stage. Its validation with the results from user tests on four advanced rider assistance systems allows confirming the social norm and the interface design as powerful predictors of the acceptance of ARAS, while the extent of perceived safety when riding without support did not have any predictive value in the present study.
The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx. However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My. The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was observed. It was also observed that the primary neck response in these tests was flexion, not extension. This correlates well with recent findings from Japan and the United States showing a correlation between neck flexion and injury in accident replication simulations and postmortem human subjects (PMHS) studies, respectively. The present certification tests may not adequately control front cervical spine bumper characteristics, which are important for neck flexion response. The certification sled test also does not include the pelvis and so cannot be used to control pelvis response and does not substantially load the lumbar bumpers and so does not control these parts of the dummy. The stiffness of all spine bumpers and of the pelvis flesh should be much more tightly controlled. It is recommended that a method for certifying the front cervical bumpers should be developed. Recommendations are also made for tighter tolerance on the input parameters for the existing certification tests.
Das Ziel der Untersuchung war, die Grenzen der Belastbarkeit eines Rollstuhl- und Personenrückhaltesystems mit Kraftknoten nach DIN 75078-2 zu ermitteln. Dazu wurden dynamische Schlittenversuche durchgeführt, bei denen die Verzögerungspulse sowie das Gesamtgewicht von Rollstuhl und Prüfpuppe variiert wurden. Für die Untersuchungen kamen ein Prüfrollstuhl, definiert nach ISO 10542, und Rückhaltesysteme mit Kraftknoten gemäß DIN 75078-2 zum Einsatz. Das Rückhaltesystem bestand aus einem Rollstuhl- und einem Personenrückhaltesystem, wobei das Rollstuhlrückhaltesystem (RRS) mit vier bzw. sechs Gurten und entsprechenden Retraktoren an einem dynamischen Schlittenaufbau befestigt wurde. Das Personenrückhaltesystem (PRS) bestand aus einem am Rollstuhl integrierten Beckengurt sowie einem Schulterschräggurt, der am Beckengurt und am Schlittenaufbau befestigt wurde. Ferner wurden bei den Versuchen Prüfpuppen verschiedener Alters- und Gewichtsklassen (P6, HIII 5 %, HIII 50 % und HIII 95 %) eingesetzt Die Belastungsanforderungen für das Rückhaltesystem wurden sukzessiv erweitert, indem einerseits das Gesamtgewicht (Rollstuhl und Prüfpuppe) und andererseits auch die Verzögerungspulse bis zur Versagensgrenze erhöht wurden. Das Vier-Gurt-Rückhaltesystem konnte bei einem Verzögerungspuls von 10 g einem Gesamtgewicht von bis zu 221 kg standhalten. Bei einem Verzögerungspuls von 20 g und einem Gesamtgewicht von 134 kg wurde das Vier-Gurt-System bis über die Grenzen belastet. Das Sechs-Gurt-Rückhaltesystem hat Belastungen bis 221 kg standgehalten. Infolgedessen ist bei einer Erhöhung der Verzögerungspulse auf 20 g und einem Gesamtgewicht von mehr als 109 kg ein Sechs-Gurt-System zu empfehlen.
It is commonly agreed that active safety will have a significant impact on reducing accident figures for pedestrians and probably also bicyclists. However, chances and limitations for active safety systems have only been derived based on accident data and the current state of the art, based on proprietary simulation models. The objective of this article is to investigate these chances and limitations by developing an open simulation model. This article introduces a simulation model, incorporating accident kinematics, driving dynamics, driver reaction times, pedestrian dynamics, performance parameters of different autonomous emergency braking (AEB) generations, as well as legal and logical limitations. The level of detail for available pedestrian accident data is limited. Relevant variables, especially timing of the pedestrian appearance and the pedestrian's moving speed, are estimated using assumptions. The model in this article uses the fact that a pedestrian and a vehicle in an accident must have been in the same spot at the same time and defines the impact position as a relevant accident parameter, which is usually available from accident data. The calculations done within the model identify the possible timing available for braking by an AEB system as well as the possible speed reduction for different accident scenarios as well as for different system configurations. The simulation model identifies the lateral impact position of the pedestrian as a significant parameter for system performance, and the system layout is designed to brake when the accident becomes unavoidable by the vehicle driver. Scenarios with a pedestrian running from behind an obstruction are the most demanding scenarios and will very likely never be avoidable for all vehicle speeds due to physical limits. Scenarios with an unobstructed person walking will very likely be treatable for a wide speed range for next generation AEB systems.
Es wurden Versuchsreihen mit Trageeinrichtungen von Motorrad- und Fahrradhelmen durchgeführt. Trageeinrichtungen sollen bei einem Unfall verhindern, dass es zu einem Verlust des Helms kommt. Zur Prüfung der Belastbarkeit von Trageeinrichtungen wurde ein Prüfstand entwickelt und aufgebaut, mit dem die Kraft, der ein Tragesystem standhalten kann, bestimmt werden kann. Die Ergebnisse belegen, dass Tragesysteme von Motorradhelmen Kräften widerstehen können, die fast dreimal so hoch sind, wie die unter Standardbedingungen der ECE-R 22 aufgebrachten. Vier der fünf getesteten Fahrradhelme widerstanden höheren Kräften als im Normentwurf gefordert.
Es wird auf die neueste Auflage des Gutachtens Krankheit und Kraftverkehr, Bonn 1995, eingegangen. Insbesondere dessen Auswirkungen für körperbehinderte Autofahrer wird beschrieben. Es wird dabei genau auf den Umfang beziehungsweise das Ausmaß der Behinderung und deren Auswirkung auf die Fahrtauglichkeit eingegangen.
Bestimmte Fragestellungen der Verkehrssicherheitsarbeit und der Unfallforschung, speziell solche zu neuen Informationstechnologien im Fahrzeug, lassen sich nur mit Fahrproben beantworten. In dem Bericht sind bisherige Erfahrungen zusammengestellt, die bei der Durchführung von Fahrproben gemacht wurden. Im einzelnen werden Verfahrensvorschläge für folgende Problembereiche erörtert: Einflussfelder, Untersuchungsinstrumente und Entwicklung von Fahrversuchen; Operationalisierung der Fragestellung; Fahrraumdefinitionen (Fahrraum und Umfeld); Verknüpfung von Situation und Fahrraumumfeld; Grundlagen und Festlegung der statistischen Prüfmethoden; Anforderungen an die Messstrecke, das Messfahrzeug und die Auswerteeinheit; Versuchsdesign und statistische Sicherheitswahrscheinlichkeit; Versuchspersonenauswahl; Homogenisierung der Versuchspersonenstichprobe; Effektstärken; Stichprobengröße; Datenerhebung; Datenstrukturierung; Auswertung sowie Dokumentation. Es handelt sich nicht um ein in sich geschlossenes Methodenbuch, sondern um einen Methodenaufriss einschließlich Literaturangaben.
Die Untersuchung sollte erörtern, ob es empfehlenswert ist, das Testverfahren zum streifenden Anprall eines Motorradhelmes auf die Straßenoberfläche in die ECE-R 22 aufzunehmen. Dazu war zu klären, ob die Testmethode geeignet ist, rotatorische Kräfte auf den Prüfkopf zu erfassen und ob sich aufgrund der Unfallsituationen eine Notwendigkeit für ein solches Testverfahren ergibt. Die Messergebnisse zeigen, dass der Zusammenhang zwischen der verletzungswirksamen Rotationsbeschleunigung und der im Testverfahren gemessenen Tangentialkraft nicht ohne Zweifel belegbar ist. Somit wäre zu fordern, dass statt der Tangentialkraft die Rotationsbeschleunigung als Verletzungskriterium betrachtet wird. Dafür wird jedoch ein sehr hoher Anspruch an die Messtechnik im Labor gestellt. Aus der Sicht der Unfallforschung lässt sich sagen, dass bei derartigen Anprallsituationen, insbesondere bei Anprallgeschwindigkeiten von unter 40 km/h, die sich im Laborversuch realisieren lassen, nur mäßige Kopfverletzungen auftreten (AIS 2 oder geringer). Der hohe Aufwand des Testverfahrens scheint also nicht gerechtfertigt zu sein.
Beschrieben wird die Evaluierung eines Testverfahrens der Arbeitsgruppe 10 des European Experimental Vehicle Committee, mit dem die "Fußgängerverträglichkeit" von Frontflächen von Personenkraftwagen bestimmt werden kann. Dabei werden verschiedene Anprallarten von Fußgängern an Fahrzeugen simuliert: der Anprall eines Beines an den Stoßfänger, der Anprall des Oberschenkels an die Vorderkante der Fronthaube und der Anprall des Kopfes auf die Fronthaube. Im Beitrag wird auf die Durchführung von Tests zum Oberschenkelanprall und zum Beinanprall an drei verschiedenen Fahrzeugtypen eingegangen. Beschrieben werden Testverfahren, Versuchsaufbau und Versuchsdurchführung. Die Versuchsreihe zeigte, dass das entwickelte Testverfahren praktikabel ist.
Der Autor berichtet über zwei Forschungsprojekte zur Prüfung von runderneuerten Reifen durch Schnell- und Dauerlaufprüfung. Es wurden Pkw- und Lkw-Reifen mit Karkassen unterschiedlicher Hersteller und unterschiedlichen Alters mit und ohne reparierte Durchstoßschäden untersucht. Die Versuchsergebnisse spechen für eine Altersbegrenzung der rundzuerneuernden Karkassen auf 6 Jahre. Das Reparieren sollte nur bei der Runderneuerung von Lkw-Reifen toleriert werden. Eine Rückstufung der Geschwindigkeitsklassen nach Runderneuerung von Pkw-Reifen zeigt eine positive Wirkung.