Sonstige
Filtern
Erscheinungsjahr
- 2013 (15) (entfernen)
Dokumenttyp
Schlagworte
- Simulation (15) (entfernen)
Institut
- Sonstige (15) (entfernen)
The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx. However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My. The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was observed. It was also observed that the primary neck response in these tests was flexion, not extension. This correlates well with recent findings from Japan and the United States showing a correlation between neck flexion and injury in accident replication simulations and postmortem human subjects (PMHS) studies, respectively. The present certification tests may not adequately control front cervical spine bumper characteristics, which are important for neck flexion response. The certification sled test also does not include the pelvis and so cannot be used to control pelvis response and does not substantially load the lumbar bumpers and so does not control these parts of the dummy. The stiffness of all spine bumpers and of the pelvis flesh should be much more tightly controlled. It is recommended that a method for certifying the front cervical bumpers should be developed. Recommendations are also made for tighter tolerance on the input parameters for the existing certification tests.
Tunnel sind bedeutende Infrastrukturbauwerke. Die Beurteilung der Folgen von Brandereignissen in Tunneln ist daher auch von außerordentlicher volkswirtschaftlicher Bedeutung. Ein solches Brandereignis stellt z.B. der Brand eines mit Benzin beladenen Tanklastzugs dar. Im Rahmen eines Forschungsvorhabens für die Bundesanstalt für Straßenwesen (BASt) wurden verschiedene Szenarien für diesen Extremfall mit unterschiedlichen Energiefreisetzungsraten und deren Einfluss auf die Tunneltragsicherheit mittels numerischer Strömungssimulationen und Finite-Elemente-Berechnungen untersucht. Es konnte gezeigt werden, dass selbst Brandszenarien mit Flüssigkeitslachenbränden von bis zu 28 t Benzin durch die ZTV-ING-Temperatur-Zeit-Kurve abgedeckt werden können. Der folgende Beitrag fasst die wesentlichsten Ergebnisse zusammen.
Einfluss der veränderten Verkehrsführung bei Ertüchtigungsmaßnahmen auf die Bauwerksbeanspruchungen
(2013)
Im Rahmen von mehreren vorhergehenden Forschungsprojekten wurden vom Forschungsnehmer Untersuchungen zu den Beanspruchungen von Brückenbauwerken infolge des Straßenverkehrs durchgeführt. Die Ergebnisse dieser Untersuchungen führten zu den neuen Verkehrslastannahmen für Straßenbrücken im Eurocode 1, Teil 2 (in Verbindung mit dem deutschen nationalen Anhang) und den Ziellastniveaus in der Nachrechnungsrichtlinie. Im Ergebnis von Nachrechnungen müssen die Bestandsbrücken ertüchtigt oder neu gebaut werden. Ertüchtigung von Autobahnbrücken heißt Bauen unter Verkehr. Auf den Bestandsbrücken ist eine veränderte Verkehrsführung erforderlich. Mit einer veränderten Verkehrsführung geht aber unter Umständen auch eine Veränderung der Beanspruchungen der Brückenbauwerke infolge dieser "Umnutzung" einher. Ziel des vorliegenden Forschungsprojektes ist es, den Einfluss der veränderten Verkehrsführung bei Ertüchtigungsmaßnahmen auf die Bauwerksbeanspruchungen zu analysieren. Unter Anwendung einer in den vorhergehenden Projekten entwickelten Vorgehensweise werden Simulationsrechnungen durchgeführt, in denen verschiedenen Varianten von Spuranordnungen auf Überbauquerschnitten betrachtet werden. Des Weiteren werden differenzierte Verkehrscharakteristiken, also verschiedene Verkehrsstärken und Verkehrszusammensetzungen, betrachtet. Grundsätzlich werden hierbei Beanspruchungen, also zum Beispiel resultierende Biegemomente oder Auflagerkräfte, betrachtet. Aus diesem Grund müssen die Berechnungen für definierte Tragsysteme durchgeführt werden. Im vorliegenden Projekt wurden hierzu zwei reale Brückenbauwerke betrachtet, die sich im Zuge von Autobahnen in Nordrhein-Westfalen befinden. Erweitert werden die Betrachtungen auf ein zusätzliches "virtuelles" Tragsystem, um ein gewisses Spektrum von Stützweiten und Querschnittsbreiten analysieren zu können. Grundsätzlich zeigt sich im Ergebnis der Untersuchungen, dass Beanspruchungen aus aktuellem Verkehr bei normaler Verkehrsführung durch das Lastmodell LM1 des DIN-Fachberichtes 101 abgedeckt werden. Für Beanspruchungen aus zukünftigem Verkehr ist das neue Lastmodell LM1 des Eurocodes erforderlich. Im Rahmen von Baumaßnahmen wird im Allgemeinen eine 4+0-Verkehrsführung eingerichtet. Hierbei werden bei zweiteiligen Überbauquerschnitten vier Fahrstreifen über einen Querschnitt geleitet. Dies geht einher mit einer Verengung der Fahrspuren. In solchen Fällen ist davon auszugehen, dass es nicht möglich ist, dass Lkw-Überholverkehr stattfinden kann. Dies führt zu einer wesentlichen Verringerung der Beanspruchungen von Brückenbauwerken, da auch in Stausituationen in den zwei Richtungsfahrbahnen keine Lkw-Fahrzeuge nebeneinander stehen können. Für Verkehrszusammensetzungen entsprechend der aus der Nachrechnungsrichtlinie bekannten Verkehrsart "Große Entfernung" (50 % Sattelzugfahrzeuge) ergibt sich daher eine Abdeckung der Beanspruchungen aus Straßenverkehr durch das Lastmodell BK60 der DIN 1072. Für Verkehrszusammensetzungen analog der Verkehrsart "Mittlere Entfernung" reicht das Lastmodell BK30/30 zu Abdeckung aus. Weitere Differenzierungen hinsichtlich der Verkehrsstärke führen hier zu keinen wesentlichen Änderungen der getroffenen Aussagen.
Ziel des Projektes war es, bedingt durch die wachsende Anzahl der im Verkehr befindlichen elektrisch und hybrid-elektrisch betriebenen Fahrzeuge, notwendige Anpassungen der periodisch technischen Überwachung zu erarbeiten. Dazu wurden von verschiedenen Fahrzeugen die relevanten Bauteile des elektrischen Antriebsstrangs identifiziert und deren Ausfallverhalten analysiert. Um die Degradationsauswirkungen einzelner Bauteile und Funktionen auf das gesamte System bestimmen zu können, hat die FSD ein Simulationsmodell erstellt. Die daraus ermittelten Ergebnisse waren Grundlage für die Bestimmung verkehrssicherheits- und umweltkritischer Bauteile sowie deren Funktionen. Diese Modellaussagen wurden mit Realversuchen an Fahrzeugen validiert. Zusätzlich konnten in einem Feldversuch 2.560 Fahrzeuge mit elektrischem Antriebsstrang untersucht werden. Aus diesen Ergebnissen lassen sich Änderungsvorschläge für die Untersuchungen und Vorgaben ableiten. Dafür ist für einen Großteil dieser Untersuchungen die Nutzung von Diagnosedaten eine geeignete Möglichkeit. Die 47. Verordnung zur Änderung straßenverkehrsrechtlicher Vorschriften berücksichtigt bereits an vielen Stellen die neuen Antriebskonzepte. Von daher werden lediglich geringe Anpassungen in der StVZO für -§ 19 und den Beispielkatalog dazu, -§ 29, Anlage VIIIa, Anlage VIIId sowie die HU-Richtlinie vorgeschlagen. Für die Durchführung der Untersuchungspunkte zum HV-System ist die Entwicklung einer Hochvolt-Richtlinie empfehlenswert. Einige wichtige Prüfverfahren lassen sich derzeit technisch noch nicht umsetzen. Dazu sind Änderungen der internationalen Bau- und Betriebsvorschriften notwendig. Diese werden bei der EU/UNECE anzuregen sein. Es besteht über dieses Projekt hinaus weiterhin Forschungsbedarf, um sich intensiv mit diesen Fahrzeugen zu befassen und deren Weiterentwicklung zu beobachten, damit notwendige Auswirkungen auf die PTI rechtzeitig erkannt werden können.
Ziel der Untersuchung war es, anhand realer Fälle adaptive Steuerungen von Lichtsignalanlagen für städtische Hauptverkehrsstraßen mit konventionellen Steuerungen zu vergleichen. Für die Untersuchung wurden je zwei Hauptverkehrsstraßen in Münster und Remscheid ausgesucht, auf denen adaptive Steuerungen eingerichtet wurden. Dabei wurde zunächst eine konventionelle Koordinierung mit weitgehend verkehrsabhängigen Elementen hergestellt. Zusätzlich konnte jeweils eine adaptive Steuerung geschaltet werden. Auf allen Strecken wurden systematisch Testfahrten bei Schaltung der verschiedenen Steuerungszustände durchgeführt. Die hierbei mittels GPS aufgezeichneten Fahrzeugtrajektorien wurden hinsichtlich der Anzahl von Halten und der Wartezeiten analysiert, um so zu einer verkehrstechnischen Beurteilung zu gelangen. Auf der ersten Teststrecke in Münster konnte durch die adaptive Steuerung eine deutliche Verbesserung des Verkehrsablaufs erreicht werden. Auf der zweiten Teststrecke in Münster ließ sich dieser Erfolg nicht wiederholen. Es traten teilweise erhebliche verkehrliche Verschlechterungen bei Schaltung der adaptiven Steuerung ein. Auf den Teststrecken in Remscheid ergaben sich durch die adaptive Steuerung in jeweils einer Fahrtrichtung Verbesserungen des Verkehrsflusses. Dem stehen jedoch Verschlechterungen in der Gegenrichtung gegenüber. Weil eine direkte Erfassung der Immissionen vor Ort nicht möglich war, wurde eine Antwort hinsichtlich der ökologischen Wirkungen durch mikroskopische Simulation gesucht. Für je eine Strecke in Münster und Remscheid wurde die adaptive Steuerung in ein VISSIM-Modell integriert. Die simulierten Fahrzeugtrajektorien wurden durch das Verfahren PHEM im Hinblick auf die Schätzung der Emissionen analysiert. Dabei zeigte sich in Münster eine leichte Verbesserung (1,0 %) der ökologischen Auswirkungen als Folge der adaptiven Steuerung. In Remscheid zeigte sich nach den eingetretenen ungünstigen verkehrlichen Wirkungen erwartungsgemäß auch eine Verschlechterung der ökologischen Auswirkungen. Die Ergebnisse der mikroskopischen Simulation in Verbindung mit der adaptiven Steuerung auf diesem Streckenzug unterlagen jedoch erheblichen Schwankungen, sodass hiermit lediglich tendenzielle Aussagen möglich sind. Im Ergebnis zeigte sich, dass die adaptiven Verfahren die Möglichkeit eröffnen, den Verkehrsfluss auf städtischen Hauptverkehrsstraßen zu verflüssigen. Dabei können auch Verbesserungen hinsichtlich der Schadstoffemissionen und des Energieverbrauchs eintreten. Diese Verbesserungen können jedoch nicht uneingeschränkt vorausgesetzt werden, sondern bedürfen einer zum Teil längerfristigen, kostenintensiven Einstellungsphase.
Accident research 2.0: New methods for representative evaluation of integral safety in traffic
(2013)
BMW has developed a procedure for rating Advanced Driver Assistance Systems (ADAS) benefits that integrates two distinct tools. The tool "S.A.F.E.R." is designed to analyze the pre-crash phase. The aim of S.A.F.E.R. is to simulate all relevant processes in sufficient detail to obtain reproducible estimates of key indicators (effectiveness, false positives, etc.). The relevant processes include not only traffic and vehicle dynamics, but also environmental and most importantly human factors. Representative distributions of factors and parameters are obtained by taking the stochastic variation of all relevant parameters into account in the simulations. The second tool, known as "ICOS", has been designed to provide a high-resolution, high-fidelity description of crash phase dynamics. If one converts the outputs of stochastic simulation into inputs for crash dynamics, the result is a comprehensive description of exactly how a safety system can reduce injuries. Applications currently focus on high-fidelity simulation of individual crashes in order to enhance our understanding and optimization of connected safety systems. An integrated simulation process thus allows an exact prediction of the effectiveness in individual cases in terms of injury severity. The development and rating of integral safety need to reflect the true efficiency in the field. The integrated approach described here could provide a valid and reproducible basis for rating connected systems of active and passive safety. In particular, "virtual experiments" using a traffic-based approach and incorporating models of all relevant processes constitute an essential element of the approach.
The presentation deals with the simulation tool rateEFFECT which intends to answer the following questions: Which active safety systems should be developed to maximize safety benefit in real traffic accidents? What is the effectiveness of a specific active safety system in the real world? How many casualties could be avoided by such a system? It is shown that a lot of information is required to simulate existing accidents in order to estimate ADAS effects. This particularly includes numerical values for the pre-crash and in-crash phase. The database GIDAS provides a required minimum number of these parameters for a statistically significant sample.
The paper aims to study the injury risk and kinematics of pedestrians involved in different passenger vehicle collisions. Furthermore, the difference of pedestrian kinematics in the accidents involved minivan and sedan was analyzed. The 18 sample cases of passenger car to pedestrian collisions were selected from the database of In-depth Investigation of Vehicle Accident in Changsha of China (IVAC),of which the 12 pedestrian accidents involved in a minivan impact for each case, and the 6 accidents in a sedan impact for each. The selected cases were reconstructed by using mathematical models of pedestrians and accident vehicles in a multi-body dynamic code MADYMO environment. The logistic regression models of the risks for pedestrian AIS 3+ injuries and fatalities were developed in terms of vehicle impact speed by analyzing the minivan-pedestrian and sedan-pedestrian accidents. The difference of pedestrian kinematics was identified by comparing the results from reconstructed pedestrian accidents between the minivans and sedans collisions. The result shows that there is a significant correlation among the impact speed and the severity of pedestrian injuries. The minivan poses greater risk to pedestrian than sedan at the same impact speed. The kinematics of pedestrian was greatly influenced by vehicle front shape.
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
Real world accident reconstruction with the Total Human Model for Safety (THUMS) in Pam-Crash
(2013)
Further improvement of vehicle safety needs detailed analysis of real world accidents. According to GIDAS (German In-Depth Accident Study) most car to car front accidents occur at mid-crash severity. In this range thoracic injuries already occur. In this study a real world frontal crash with mid-crash severity out of the AARU database was reconstructed. The selected car to car accident was reconstructed by AARU by means of pc-crash software in order to get the initial dynamic accident conditions. These initial conditions were used to reconstruct the complete accident in more detail using FE models for the car structure and the occupants. Occupant simulations were performed with FE HIII-dummy models and the THUMS using Pam-Crash code. An initial THUMS validation was performed in order to verify the model-´s biofidelity by means of table-top test simulations. THUMS bone stiffness values were modified to match the real word occupant age. A comparison between driver and passenger restraint system loading was done, as well as an injury prediction comparison between the HIII-dummy model and THUMS response for both cases. Detailed comparison between the HIII-dummy models and THUMS regarding thoracic loading are discussed.
The main objective of EC CASPER research project is to reduce fatalities and injuries of children travelling in cars. Accidents involving children were investigated, modelling of human being and tools for dummies were advanced, a survey for the diagnosis of child safety was carried out and demands and applications were analysed. From the many research tasks of the CASPER project, the intention of this paper is to address the following: • In-depth investigation of accidents and accident reconstruction. These will provide important points for the injury risk curve, in order to improve it. Different accident investigation teams collected data from real road accidents, involving child car passengers, in five different European countries. Then, a selection of the most appropriate cases for the injury risk curve and the purposes of the project was made for an in-depth analysis. The final stage of this analysis was to conduct an accident reconstruction to validate the results obtained. The in-depth analysis included on-scene accident investigation, creating virtual simulations of the accident/possible reconstruction, and conducting the reconstruction. In the cases of successful reconstructions, new points were introduced to the injury risk curves. Accident reconstructions of selected cases were carried out in test laboratories as the next step following in-depth road accident investigation. These cases were reconstructed using similar child restraint systems (CRS) and the same type make and model as in the real accidents. Reconstructing real cases has several limitations, such as crash angle, cars" approximation paths and crash speed. However, a few changes and applications on the testing conditions were applied to reduce the limitations and improved the representations of the real accidents. After conducting the reconstructions, a comparison between the deformations of the cars on the real accident and the vehicles from the reconstructions was made. Additionally, a correlation between the data captured from the dummies and the injury data from the real accident was sought. This finalises an in-depth analysis of the accident, which will provide new relevant points to the injury risk curve. The CASPER project conducted a large research programme on child safety. On technical points, a promising research area is the developing injury risk curves as a result of in-depth accident investigations and reconstructions. This abstract was written whilst the project was not yet finished and final results are not yet known, but they will be available by the time of the conference. All the works and findings will not necessarily be integrated in the industrial versions of evaluation tools as the CASPER project is a research program.
The sequence of accident events can be classified by three essential phases, the pre-crash-sequence, the crash-sequence and the post-crash-sequence. The level of reliability of the information in the GIDAS-database (German In Depth Accident Study) is provided predominantly on the passive side. The period to evaluate active safety systems begins already in the pre-crash-sequence. The assessment of the potential of sensor- or communication-based active safety systems can only be accomplished by a detailed analysis of the pre-crash-phase. Hence the necessity to analyze the early period of the accident event in detail arises. This is possible with the help of the digital sketches of the accident site and the simulation of the accident by a simulation method of the VUFO GmbH. After simulating the pre-crash scenario it is possible to generate additional and standardized data to describe the pre-crash-sequences of an accident in a very high detail. These data are documented in a second database called the GIDAS Pre-Crash-Matrix (PCM). The PCM contains various tables with all relevant data to reproduce the pre-crash-sequence of traffic accidents from the GIDAS database until 5 seconds before the first collision. This includes parameters to describe the environment data, participant data and motion or dynamic data. This paper explains the creation of the PCM, the simulation itself and the contents and structure of the PCM. With this information of the pre-crash-sequence for various accident scenarios an improved benefit estimation and development of active safety systems can be made possible.
The objective of the study is to measure the risk of pedestrian and bicyclist in urban traffic through an analysis of real-world accident data. The kinematics and injury mechanisms for both pedestrian and bicyclists are investigated to find the correlation of injury risks with injury related parameters. For this purpose, firstly 338 cases are selected as a sample from an IVAC accident database based on the In-depth Investigation of Vehicle Accident in Changsha of China. A statistic measurement of the fatality and serious injury risks with respect to impact speed was carried out by logistic regression analysis. Secondly, 12 pedestrian and 12 bicyclist accidents were further selected for reconstruction with MADYMO program. A comparative analysis was conducted based on the results from accident analysis and computer reconstructions for the injury risk, head impact conditions and dynamic response of pedestrians and bicyclists. The results indicate that bicyclists suffered lower risks of severe injuries and fatalities compared with pedestrians. The risks of AIS 3+ injury and fatality are 50% for pedestrians at impact speeds of 53.2 km/h and 63.3 km/h, respectively, while that for bicyclists at 62.5 km/h and 71.1 km/h, respectively. The findings could have a contribution to get a better understanding of pedestrians" and bicyclists" exposures in urban traffic in China, and provide background knowledge to generate strategies for pedestrian protection.
Cycle helmets have continued to increase in popularity since their introduction half a century ago. Many studies indicate that overall, head injury can be significantly reduced by wearing them. This study was conducted using two distinct sets of real-world cycling collision data from Ireland, namely cases involving police collision reports and cases involving admission to a hospital emergency department. The analyses sought to simulate and analyse the protective performance of cycle helmets in such collision scenarios, by comparing the Head Injury Criterion score and peak head accelerations, both linear and angular. Cycle collisions were simulated using the specialised commercial software MADYMO. From the simulation results, these key metrics were compared between the same-scenario helmeted and unhelmeted cyclist models. Results showed that the inclusion of bicycle helmets reduced linear accelerations very significantly, but also increased angular accelerations significantly compared to unhelmeted situations. Given the modest protective performance of cycle helmets against angular accelerations, it is recommended that cycle helmet manufacturers and international test standards need to pay more attention to head angular accelerations.
In Anbetracht des stetigen Wachstums des Schwerverkehrsaufkommens auf dem deutschen und europäischen Straßennetz wurden durch das Bundesministerium für Verkehr, Bau und Stadtentwicklung (BMVBS) und die Bundesanstalt für Straßenwesen (BASt) in der jüngsten Vergangenheit mehrere Forschungsprojekte initiiert, um die Auswirkungen dieses wachsenden Verkehrsaufkommens auf die Brückenbauwerke, sowohl hinsichtlich des Brückenneubaus als auch hinsichtlich des Brückenbestandes, zu analysieren. Vom Forschungsnehmer wurden hierzu in vorhergehenden Projekten auf der Grundlage von Verkehrssimulationsrechnungen verschiedene Lastmodelle identifiziert, die die Beanspruchungen infolge prognostiziertem zukünftigen Verkehr oder eines in gewissen Teilen bekannten objektspezifischen Verkehres abdecken. Die Relevanz der identifizierten Lastmodelle in den Sicherheitskonzepten wurde bisher nicht untersucht. Dies steht im Schwerpunkt dieser Projektaufgabe. Für ein ausgewähltes Tragsystem (2x40 m Zweifeldsystem mit einem zweistegigen Plattenbalkenquerschnitt in Massivbauweise) wurden hierzu sicherheitstheoretischen Untersuchungen durchgeführt. Grundlage solcher Untersuchungen ist die Berücksichtigung von streuenden (zufälligen) Kenngrößen zur Abbildung von inneren Widerständen diesen gegenüber stehenden Beanspruchungen. Für die stochastische Beschreibung der Beanspruchungen infolge des Straßenverkehrs wurden die Ergebnisse der in den vorhergehenden Forschungsprojektes Verkehrssimulationsrechnungen verwendet und eine Vorgehensweise zur Aufbereitung dieser Datenbestände entwickelt. Hierdurch ist es möglich, eine differenzierte stochastische Beschreibung der Beanspruchungen aus Verkehrseinwirkungen unter Kenntnis objektspezifischer Verkehrscharakteristiken zu erstellen. Im Ergebnis der Untersuchungen zeigt sich, dass über verschiedene betrachtete Verkehrscharakteristiken und zugehörige Lastmodelle hinweg relativ homogene Sicherheitsindizes ergeben. Unter Berücksichtigung von Modellunsicherheiten auf der Einwirkungs- und Widerstandsseite liegen die Ergebnisse leicht über den "normativen Vorgaben" des Sicherheitsindexes.