Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (151) (entfernen)
Schlagworte
- Germany (151) (entfernen)
Institut
Injuries in motorbike accidents in correlation with protective clothes and mechanism of the accident
(2013)
This study deals with a possible connection between safety clothing / accident mechanism and injury severity in a state-wide traffic accident investigation with focus on light and small motorbike-involvement for accidents in the area of the Saarland in which the persons riding the bike have been injured or killed. An interdisciplinary team of medical scientists and engineers collected the medical and technical data as well as all the relevant traces of the accident on scene and in time. During twenty months of data collection a total of 401 cases could be gathered. Grave injuries were more common for the group of heavier motorcycles (>125 ccm). Motorcyclists had been polytraumatized only in the group where the accident was connected with a collision. Significant correlation between protective clothes and injury severity could only be found for protective gloves and protective trousers. The knowledge about mechanism of the accident, protective clothes and severity of injuries can be helpful for the improvement of road and motorcyclists' safety.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
This study analyses no.39 cases in which n.41 motorcyclists were fatally injured, or 36% of total motorcycle fatalities in Northern Ireland between 2004 and 2010 (n.114). There were n.17 cases (43.6%) where the actions of another vehicle driver caused the collision, in thirteen of these cases the motorcycles had their lights switched on. The remaining n.22 collisions (56.4%) were due to the actions of the motorcyclist. In the approach to the collision scene, there were n.13 cases (31.7%) in which the approach was a right hand bend and in n.8 (19.5%) cases, the approach was a left hand bend. In the remaining n.18 (43.9%) cases, the approach was a straight road. Of the n.17 (41.4%) motorcycles that slid after falling, n.10 (24.4%) fell onto their right side and the remaining n.7 (17.1%) fell onto their left side. The information from this study identifies primary and contributory causes of motorcycle collisions.
The objective of the study is to measure the risk of pedestrian and bicyclist in urban traffic through an analysis of real-world accident data. The kinematics and injury mechanisms for both pedestrian and bicyclists are investigated to find the correlation of injury risks with injury related parameters. For this purpose, firstly 338 cases are selected as a sample from an IVAC accident database based on the In-depth Investigation of Vehicle Accident in Changsha of China. A statistic measurement of the fatality and serious injury risks with respect to impact speed was carried out by logistic regression analysis. Secondly, 12 pedestrian and 12 bicyclist accidents were further selected for reconstruction with MADYMO program. A comparative analysis was conducted based on the results from accident analysis and computer reconstructions for the injury risk, head impact conditions and dynamic response of pedestrians and bicyclists. The results indicate that bicyclists suffered lower risks of severe injuries and fatalities compared with pedestrians. The risks of AIS 3+ injury and fatality are 50% for pedestrians at impact speeds of 53.2 km/h and 63.3 km/h, respectively, while that for bicyclists at 62.5 km/h and 71.1 km/h, respectively. The findings could have a contribution to get a better understanding of pedestrians" and bicyclists" exposures in urban traffic in China, and provide background knowledge to generate strategies for pedestrian protection.
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
The effect of fatigue on driving has been compared to the effect of alcohol impairment in both driver performance and crash studies. However are crash characteristics and causation mechanisms similar in crashes involving fatigue to those involving alcohol when studied in the real world? This has been explored by examining data held in the EC project SafetyNet Accident Causation Database. Causation data was recorded using the SafetyNet Accident Causation System (SNACS). The focus was on Cars/MPV crashes and drivers assigned the SNACS code Alcohol or Fatigue. The Alcohol group included 44 drivers and the Fatigue group included 47. "Incorrect direction" was a frequently occurring critical event in both the Alcohol and Fatigue groups. The Alcohol group had more contributory factors related to decision making and the Fatigue group had more contributory factors relating to incorrect observations. This analysis does not allow for generalised statements about the significance of the similarities and differences between crashes involving alcohol and fatigue, however the observed differences do suggest that attempts to quantify the effect of fatigue by using levels of alcohol impairment as a benchmark should be done with care.
The European CASPER (Child Advanced Safety Project for European Roads) project studying car child safety includes a sociological approach in order to have a better understanding of the behaviour of parents driving children under 12 years old. A questionnaire was distributed via the internet in Europe with 998 parents (representing 1638 children) from 22 European countries responding. The results inform on the way parents secure their children during a car trip. Many parents did not control how their children were installed in the child restraint system (CRS). A toddler was more likely to travel into a child seat than an older child was. Regarding misuse situations, an important part of the participants did not think that they could make mistakes when fixing the child seat to the car (26%) or when placing the child into the seat (39%). This leaves an important field of action especially by communication via different media and in the CRS sale outlets.
Cycle helmets have continued to increase in popularity since their introduction half a century ago. Many studies indicate that overall, head injury can be significantly reduced by wearing them. This study was conducted using two distinct sets of real-world cycling collision data from Ireland, namely cases involving police collision reports and cases involving admission to a hospital emergency department. The analyses sought to simulate and analyse the protective performance of cycle helmets in such collision scenarios, by comparing the Head Injury Criterion score and peak head accelerations, both linear and angular. Cycle collisions were simulated using the specialised commercial software MADYMO. From the simulation results, these key metrics were compared between the same-scenario helmeted and unhelmeted cyclist models. Results showed that the inclusion of bicycle helmets reduced linear accelerations very significantly, but also increased angular accelerations significantly compared to unhelmeted situations. Given the modest protective performance of cycle helmets against angular accelerations, it is recommended that cycle helmet manufacturers and international test standards need to pay more attention to head angular accelerations.
The grip between the road surface and vehicle tires is the physical basis for the moving of all vehicles in road traffic. In case of an accident the available grip level is one of the most relevant influence factors, influencing the causation and the procedure of the accident. However, the estimation of the grip level is not easy and therefore, is commonly not done on the accident scene. This is especially true for the measurement of the water depth. Until now, real accident databases provide no measurement data about the grip level and the water film depth and thus, the estimation of its influence is not possible yet. From the tyre manufacturers point of view, it is important to know about the road conditions (namely grip level, macro-texture, water depth, temperature) at the accident scene, as well as the operating conditions of the vehicles (braking, loss of control, speed, etc). These data is necessary to define relevant tyre traction tests for the end-user and for regulations. For this reason VUFO and Michelin developed a consistent method for the measurements of grip level and water depth for the accidents of the GIDAS database. The accident research team of Dresden, which documents about 1000 accidents with at least one injured person every year, is measuring the micro-roughness and the macro-roughness directly on the spot. For the measurement of the micro-roughness a Skid Resistance Tester (British Pendulum) is used. The Mean Texture Depth (describing the macro-roughness) is measured by the Sand Depth Method. Since June 2009, measurements for more than 700 accidents including 1200 participants have been carried out. In case of wet or damp road conditions during the accident, the water depth is measured additionally. Therefore VUFO and Michelin developed a special measurement device, which allows measurements with an accuracy of 1/10 millimetre. The measurement point at the accident scene is clearly defined and thus, the results are comparable for all different accidents and participants. The use of the GIDAS database and the accident sampling plan allows representative statements for the German accident scenario. With this data it is possible for the first time to have an accurate view of the road conditions at the accident scene. One possibility is a more detailed estimation of hydroplaning accidents using the actually measured water depths. The development of new testing methods and new tires can be based on the real situation of the road infrastructure. Furthermore, the combination of the technical GIDAS data and the measured road surface properties can also be used for the estimation of effectiveness of several safety systems like the brake assist and/or emergency braking systems. The calculation of a reduced collision speed due to the use of a brake assist is only one example for the application of real measured grip level data.
The GIDAS-investigation team of Dresden (VUFO) has documented more than 11.500 accidents since 1999. The documentation of the accident includes beside vehicle-, injury- and environmental-data very detailed reconstruction data. Within this accident investigation the VUFO began to record the skid resistance of the accident site in 2009. The measurements are divided in macro- and microroughness (Sand depth method and Portable Skid Resistance Tester-SRT-by Munro-Stanley London-©). Both methods are used to determine the skid resistance for more than 1000 passenger cars. The aim of the present study is to find out a relationship between the measured skid resistance, the road conditions and the friction coefficient, which is used to calculate the maximum accelerations and decelerations during a reconstruction of an accident. Basic approach to convert the SRT-value into the friction coefficient is the calculation of the theoretical absorbed energy of the spring rubber system of the swinging arm of lever. This absorbed energy is used to get the friction coefficient by using the equations for the work of friction. To consider the road-behavior, in correlation to the friction coefficient, the results will be merged with existing literature. Last step for this study will be a comparison between actual used friction coefficients all over the GIDAS-database and the theoretical results. The study shows, if it is possible to use the SRT-Measurement for the estimation of a friction coefficient for the reconstruction of a traffic accident. As expected, the GIDAS-Database and the additional measurement of the roughness of the road directly on the spot are an enormous useful dataset.
Analysis of the accident scenario of powered two-wheelers on the basis of real-world accidents
(2013)
For the first time since 20 years the German national statistics of traffic accidents revealed an increasing number of fatalities and seriously injured persons in 2011. This negative development was especially caused by increasing numbers in all groups of vulnerable road users (VRU). Furthermore, the comparison of fatality reduction rates between several categories of road users shows that persons on motorcycles show the worst performance over years. Although every second fatality in German traffic accidents is still a car occupant, users of PTW make up more than 20% in the meantime. Assuming further improvements in the field of occupant protection this trend will continue. For that reason, a study on the basis of real-world accidents was conducted to describe the accident scenario involving motorcycles and to identify the reasons of the above-described fact. Approximately 1.800 motorcycle accidents out of GIDAS database were used for the analyses. The first part of the study deals with the question how representative the GIDAS database is for the German motorcycle accident scenario. Afterwards, detailed descriptive statistics on motorcycle accidents were presented considering numerous parameters about the accident scene, environmental influences, vehicle information, individual characteristics, interview data, injury severity and injury causation. One important point is the identification of the most frequent critical situations that are typical for motorcycle accidents. Furthermore, a special focus was on accident causation. Finally, conspicuous facts out of the analysis are emphasized. All in all, the study gives a comprehensive overview about the German motorcycle accident scenario. One the one hand, the use of weighted GIDAS data allows representative and robust statements on the basis of large case numbers; on the other hand highly detailed conclusions can be drawn. The results of the study help to understand the particularities of motorcycle accidents and provide approaches for further improvements in the field of PTW safety.
The increasing economics in India has an enormous growth of its road traffic. As observed from official Indian accident statistics the number of road fatalities are one of the highest worldwide. In contrast to most industrialized nations they have an rapidly increasing trend. To come along with this trend it becomes more than essential to understand the traffic accident situation. The official Indian accident statistics gives a glimpse of only basic information. Therefore more detailed data is needed. By using In-depth accident data and officially representative statistics the current accident situation can be evaluated in India, if a suitable weighting methodology is considered. Hence in 2009/2010 a pilot study with the collaboration partner JP-Research India pvt. Ldt. was gathered in Tamil Nadu in south of India. In-depth accident investigations were done around the Coimbatore area on four highways. At first, the collected data is evaluated. Due to consequent and continuous further development based on the first approach a methodology similar to NASS/CDS/GES in the US and GIDAS in Germany was developed. Of course all relevant accident related parameters including pictures and severity information were collected. As a matter of fact based on scaled sketches and reconstruction benefit analyses can be done in order to analyze the accident scenery in India. As a first outcome influence from infrastructure, missing education and vehicle safety were identified as key parameters in order to reduce the number of accidents and casualties. To compare the accident situation against international standards an accident classification for left hand traffic was developed based on the German Insurance classification system. Looking into detail additional accident types were identified and added to create an Indian accident type catalogue. The positive results encouraged several OEMs to participate in this investigation and together with BOSCH a consortium was established in 2010/11. Within one year from beginning in May 2011 about 200 highway accidents were collected, reported and reconstructed using the new standard. Hence a first good overview of the accident situation is available for the Coimbatore Tamil Nadu area. The major target for establishing accident investigations is the extension towards other states of India and urban areas to achieve a better overview of the accident scenery. Therefore local and national authorities have to be embedded in order to strengthen the awareness against traffic safety.
With an ever rising human life expectancy the share of elderly people in society is constantly rising. This leads to the fact that at the same rate the share of people with age related diseases such as dementia and poor eyesight taking part in traffic will rise and therefore traffic accidents caused by this group of people due to the disease will play an ever greater role. This Situation will be among the future challenges of road safety work. At present this study displays specific characteristics of accidents caused by elderly car drivers (aged 65 or higher) based on the analysis of the German In-Depth Accident Study GIDAS. Herein almost 1000 elderly car drivers were identified as accident participants in the years 2008 to 2011. The focus of this study lies on identifying special types of accidents which are caused by elderly drivers and on characterizing these types with the information gathered on scene and by interviewing the participants. The main evidence analyzed is the knowledge about the accident locality, the trajectories of the participants as well as the reasons for the occurrence of the accidents. Furthermore personal information such as the personal condition before the accident and driving purposes is used to identify patterns of contributing circumstances for accidents caused by elderly traffic participants.
Having a look at safety to traffic and the prevention of accidents it can be observed that technical improvements in active safety of vehicles have let to various positive effects in this area. Among other components the tyre-road-contact takes a key role in the development of active safety technologies. All forces in accelerating, breaking and vehicle guidance have to be transmitted through the tyre-road contact area by friction forces. A common way to characterize a friction process is to identify the coefficient of friction μ between two touching materials. Even though there are several approaches to experimentially characterise road surfaces, no standard method exists. In this paper an overview of existing test methods is given. Furthermore the preliminary design of a newly developed portable test device with its possibility to investigate the tyre-road-friction of arbitrary roads or even places of accidents is shown.
Since 2008, the authors inspected fatal traffic accidents on the spot every year, with the cooperation of Toyota police station in Aichi pref. In the jurisdiction, numbers of fatal accidents were 18 in 2008, 12 in 2009, 14 accidents in 2010, and 16 in 2011. We here report the results of our analysis of information obtained by detailed inspection for those that occurred from 2008 to 2010. We focused on vehicle-to-pedestrian accidents, which accounted for about 45% of all accidents in 2008. Because many accidents occurred on residential roads not far from pedestrians" homes, it was revealed that the decrease of the collision speed by traffic calming such as humps and zone speed management, was highly effective. On the other hand, pedestrian detection technologies seemed to be also effective as a countermeasure on vehicle side. Every pedestrian position against a vehicle was clarified and TTC (Time to Collision) was calculated provisionally. Pedestrian accidents in intersections were also examined. Among the intersection pedestrian accidents within the jurisdiction, compared with the national average in Japan, the ratio of intersections without a signal and the ratio without a pedestrian crossing were high. According to the comparison of the Japanese traffic accident patterns between 2001 and 2008, pedestrian accidents during turning right and turning left did not decrease much. For elderly drivers, these accidents occurred very often. Finally, single vehicle accidents were analysed with the accident pattern analysis methods used above. There were high numbers of single vehicle accidents against object on single roads. Although fatal accidents against guardrails decreased, the numbers of fatal accidents against a utility pole and a sign pole were nearly constant. As for the impact with narrow width objects such as utility poles, the fatality rate was very high, and countermeasures of both road infrastructure and vehicles seem to be effective.
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
The presentation deals with the simulation tool rateEFFECT which intends to answer the following questions: Which active safety systems should be developed to maximize safety benefit in real traffic accidents? What is the effectiveness of a specific active safety system in the real world? How many casualties could be avoided by such a system? It is shown that a lot of information is required to simulate existing accidents in order to estimate ADAS effects. This particularly includes numerical values for the pre-crash and in-crash phase. The database GIDAS provides a required minimum number of these parameters for a statistically significant sample.
Accident research 2.0: New methods for representative evaluation of integral safety in traffic
(2013)
BMW has developed a procedure for rating Advanced Driver Assistance Systems (ADAS) benefits that integrates two distinct tools. The tool "S.A.F.E.R." is designed to analyze the pre-crash phase. The aim of S.A.F.E.R. is to simulate all relevant processes in sufficient detail to obtain reproducible estimates of key indicators (effectiveness, false positives, etc.). The relevant processes include not only traffic and vehicle dynamics, but also environmental and most importantly human factors. Representative distributions of factors and parameters are obtained by taking the stochastic variation of all relevant parameters into account in the simulations. The second tool, known as "ICOS", has been designed to provide a high-resolution, high-fidelity description of crash phase dynamics. If one converts the outputs of stochastic simulation into inputs for crash dynamics, the result is a comprehensive description of exactly how a safety system can reduce injuries. Applications currently focus on high-fidelity simulation of individual crashes in order to enhance our understanding and optimization of connected safety systems. An integrated simulation process thus allows an exact prediction of the effectiveness in individual cases in terms of injury severity. The development and rating of integral safety need to reflect the true efficiency in the field. The integrated approach described here could provide a valid and reproducible basis for rating connected systems of active and passive safety. In particular, "virtual experiments" using a traffic-based approach and incorporating models of all relevant processes constitute an essential element of the approach.
Nowadays human-created systems are increasing in complexity due to the interaction of humans and technology. Especially road traffic systems are composed of multitudinous resources (e.g. personnel, vehicles, organizations, etc.), which make it even harder to anticipate the positive and negative effects on safety. One key in achieving a significant reduction of fatalities is seen in driver assistant systems counterbalancing the lack of drivers' capabilities. But the actual outcome of implementing these sophisticated technologies especially on influencing driver's capabilities are yet unknown. Latest research exemplifies an increase of reaction times of drivers in case of dysfunctional driver assistant systems. This research paper applies STAMP/STPA (STAMP = systems-theoretic accident model and processes; STPA = systems-theoretic process analysis) to the German automobile traffic system focusing on the effects of driver assistant systems on drivers. By doing so, the potential hazards caused by technology can be identified.