Sonstige
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.
A series of drop tests and vehicle tests with the adult head impactor according to Regulation (EC) 631/2009 and drop tests with the phantom head impactor according to UN Regulation No. 43 have been carried out by the German Federal Highway Research Institute (BASt) on behalf of the German Federal Ministry of Transport, Building and Urban Development (BMVBS). Aim of the test series was to study the injury risk for vulnerable road users, especially pedestrians, in case of being impacted by a motor vehicle in a way described within the European Regulations (EC) 78/2009 and (EC) 631/2009. Furthermore, the applicability of the phantom head drop test described in UN Regulation No. 43 for plastic glazing should be investigated. In total, 30 drop tests, thereof 18 with the adult head impactor and 12 with the phantom head impactor, and 49 vehicle tests with the adult head impactor were carried out on panes of laminated safety glass (VSG), polycarbonate (PC) and laminated polycarbonate (L-PC). The influence of parameters such as the particular material properties, test point locations, fixations, ambient conditions (temperature and impact angle) was investigated in detail. In general, higher values of the Head Injury Criterion (HIC) were observed in tests on polycarbonate glazing. As the HIC is the current criterion for the assessment of head injury risk, polycarbonate glazing has to be seen as more injurious in terms of vulnerable road user protection. In addition, the significantly higher rebound of the head observed in tests with polycarbonate glazing is suspected to lead to higher neck loads and may also cause higher injury risks in secondary impacts of vulnerable road users. However, as in all tests with PC glazing no damage of the panes was observed, the risk of skin cut injuries may be expected to be reduced significantly. The performed test series give no indication for the test procedure prescribed in UN Regulation No. 43 as a methodology to approve glass windscreen not being feasible for polycarbonate glazing, as all PC panes tested fulfilled the UN R 43 requirements. The performance of the windscreen area will not be relevant for vehicle type approval according to the upcoming UN Regulation for pedestrian protection. However, it is recommended that pedestrian protection being considered for plastic windscreens to ensure at least the same level of protection as glass windscreens.
Automotive interiors have long been a potentially injurious impact area to occupants during accidents, especially in the absence of adequate padding. The U.S. Federal Motor Vehicle Safety Standard (FMVSS) 201, Occupant Protection in Interior Impact, outlines test procedures and performance criteria in order to mitigate potentially injurious head impacts to interior surfaces. FMVSS 201 specifies a finite set of impact locations and applies to passenger vehicles of a specified year range and with a gross vehicle weight rating less than 10,000 lb. In this paper, two head impact test methodologies are presented, a pendulum-test device and a Free Motion Headform (FMH) launching device, which allows for dynamic, repeatable impact evaluation of various vehicle interior surfaces and their impact attenuation abilities. The presented testing includes multiple series that evaluate the effect of differing vehicle upper interior padding on occupant head injury. One study in particular, analyzes a head impact to the side header of a heavy truck (not included in FMVSS 201) during a 90 degree rollover. Additionally, two other series of tests are presented which assess the injury reduction effect of side airbags to near side as well as far side occupants in a side impact scenario. Lastly, a forensic analysis is presented which evaluates two possible head impact locations experienced in a real world accident by analysis of the resulting interior compartment damage utilizing the FMH launching device test method. The data collected and presented includes accelerometer instrumentation and high speed video analysis. These studies demonstrate that adequate padding and airbags are very effective at mitigating head injury potential at impact speeds of 12-25 mph (19-40 kph).
Rollovers continue to be a major source of heavy truck fatalities when compared to other accident modes. Real world rollover accidents are analyzed and two distinct damage patterns are identified. Damage to heavy truck roofs can occur from lateral loading that transitions to vertical roof loading as the vehicle rolls onto its side and then over onto its roof. A second load path can occur when the vehicle has rolled onto its side and furrows into the ground generating large longitudinal friction forces between the roof and ground. A review of the previous literature and various test methodologies are presented. A sled impact test methodology is presented which allows for structural assessment of a heavy truck cab's crashworthiness in both of these loading environments. Two test series are presented using the sled impact test methodology in order to analyze real world truck rollovers using varying impact platen and contact angles. The structural deformation and failure patterns were found to be consistent with damage seen in real world accident vehicles. In each case, a second equivalent truck cab was then reinforced and tested under similar conditions to evaluate the energy management and crush resistance of a stronger cab structure. These structural reinforcements demonstrated a substantial reduction in roof crush and protected the survival space of the occupant compartment. The sled impact test procedure is an effective method for testing the structural performance of a heavy truck cab in a variety of loading scenarios comparable to real world accidents and ascertaining the load and energy load levels in these accident modes.
The main objective of EC CASPER research project is to reduce fatalities and injuries of children travelling in cars. Accidents involving children were investigated, modelling of human being and tools for dummies were advanced, a survey for the diagnosis of child safety was carried out and demands and applications were analysed. From the many research tasks of the CASPER project, the intention of this paper is to address the following: • In-depth investigation of accidents and accident reconstruction. These will provide important points for the injury risk curve, in order to improve it. Different accident investigation teams collected data from real road accidents, involving child car passengers, in five different European countries. Then, a selection of the most appropriate cases for the injury risk curve and the purposes of the project was made for an in-depth analysis. The final stage of this analysis was to conduct an accident reconstruction to validate the results obtained. The in-depth analysis included on-scene accident investigation, creating virtual simulations of the accident/possible reconstruction, and conducting the reconstruction. In the cases of successful reconstructions, new points were introduced to the injury risk curves. Accident reconstructions of selected cases were carried out in test laboratories as the next step following in-depth road accident investigation. These cases were reconstructed using similar child restraint systems (CRS) and the same type make and model as in the real accidents. Reconstructing real cases has several limitations, such as crash angle, cars" approximation paths and crash speed. However, a few changes and applications on the testing conditions were applied to reduce the limitations and improved the representations of the real accidents. After conducting the reconstructions, a comparison between the deformations of the cars on the real accident and the vehicles from the reconstructions was made. Additionally, a correlation between the data captured from the dummies and the injury data from the real accident was sought. This finalises an in-depth analysis of the accident, which will provide new relevant points to the injury risk curve. The CASPER project conducted a large research programme on child safety. On technical points, a promising research area is the developing injury risk curves as a result of in-depth accident investigations and reconstructions. This abstract was written whilst the project was not yet finished and final results are not yet known, but they will be available by the time of the conference. All the works and findings will not necessarily be integrated in the industrial versions of evaluation tools as the CASPER project is a research program.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
The utilisation of secondary-safety systems to protect occupants has attained a very high level over the past decades. Further improvements are still possible, but increasingly minor progress is only to be had with a high degree of effort. Thus, a key aspect must be the impact to overall safety in an accident. If reliable information is available on an imminent crash, measures already taken in the pre-crash phase can result in a significantly great influence on the outcomes of the crash. With this background preventive measures are the key to a sustainable further reduction of the figures of crash victims on our roads. This paper aims to show a preventive approach that can contribute to lessening the consequences of a crash by creating an optimum interaction of measures in the fields of primary and secondary safety. To further enhance vehicle safety, driver assistant systems are already available that warn the driver of an imminent front-to-rear-end crash. The next step is to support him in his reactions or if he fails to react sufficiently, to even initiate an automatic braking when the crash becomes unavoidable. Automatic pre-crash braking can, in an ideal situation, fully prevent a crash or can significantly reduce the impact speed and thus the impact energy (and the severity of the accident). If a vehicle is being braked in the pre-crash phase, the occupants are already being pre-stressed by the deceleration. The information available about the imminent crash can be used to activate the belt tensioners and likewise other secondary safety systems in the vehicle right before the impact. The pre-crash deceleration also causes the front of the vehicle to dip. Conventional crash tests do not take this specific impact situation into consideration. This is why, for example, the influences of the pre-crash displacements of the occupants are not recorded in the test results. Furthermore, a reproducible representation of the benefit of the vehicle safety systems which prepare the occupants for the imminent impact is not possible. In order to demonstrate the functions of automated pre-crash braking and to investigate the differences during the impact as a consequence of the altered occupant positions as well as the initiation of force and deformations of the vehicle front, DEKRA teamed up with BMW to carry out a joint crash test with the latest BMW 5 series vehicle. It involved the vehicle braking automatically from a starting test speed of 64 km/h (corresponding to the impact speed set by Euro NCAP) down to 40 km/h. The test was still run by the intelligent drive system of the crash test facility. This required several modifications to be made to the test facility as well as to the vehicle. The paper will describe and discuss some relevant results of the crash test. In addition, the possible benefits of such systems will also be considered. The test supplemented the work of the vFSS working group (vFSS stands advanced Forward-looking Safety Systems).
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
Over the past two decades the popularity of consumer crash test programs, commonly referred to as New Car Assessment Programs (NCAP), has grown across the world. They are popular among government regulators as they afford a means of promoting safety innovations and levels of vehicle performance beyond those dictated by national standards. They also fulfill the demand for information regarding the safety ranking of vehicles among consumers contemplating the purchase of a new vehicle. There is no question that consumer crash test programs greatly influence vehicle design changes as well as accelerate the fitment of new safety features. The extent to which these changes can be expected to reduce serious and potentially fatal injuries will be influenced by how well the testing protocols and associated rating schemes correctly reflect the nature of the residual safety problem they seek to address. Drawing on data contained primarily in the US National Automotive Sampling System (NASS), the field relevance of current and proposed testing and rating protocols addressing frontal crash test protection is examined. Emphasis is placed on examining how accurately injury rates computed from the dummy responses measured in consumer crash tests correspond to actual injury rates observed in the field. Additional data from Canadian field investigations and US databases such as the National Motor Vehicle Crash Causation Survey (NMVCCS) are examined to see how well frontal airbag firing times, crush pulse durations and other determinants of injury are replicated in consumer testing protocols. This portion of the analysis draws on data obtained from Event Data Recorders (EDR) in both field collisions and staged tests of the same vehicle model. Vehicle rankings and overall frontal crash test ratings were found to be particularly sensitive to the choice of injury risk functions employed in the test. This was particularly true in the case of injury risk functions used to assess neck injury potential. Neck injury risk derived from Nij was found to show the least agreement with the field. Agreement between field chest injury rates and those derived from crash tests was improved considerably when chest injury risk functions for "older" occupants were employed. The paper concludes with a discussion of how different current testing protocols could be improved to enhance their field relevance.
Event Data Recorder (EDR) is an additional function installed in airbag control module (ACM) to record vehicle and occupant information for a brief period of time before, during, and after a crash event. EDRs are now being installed in ACMs by several automakers in the USA and in Japan. The aim of this study is to understand the performance of EDRs for the improvement of accident reconstruction with more reliable information. In the first report of the study, data obtained from EDRs of seven vehicle types were evaluated using 2006-2007 J-NCAP (Japanese new car assessment program) full-lap frontal barrier crash tests and offset frontal deformable barrier crash tests data. For more practical standpoint, we conducted thirteen crash tests reconstructing typical real-world accidents such as single vehicle accidents with barriers or poles, car to car accidents and multi rear-end collisions focusing on Japanese typical accident types. Data obtained from EDRs are compared with data obtained from optical speed sensor, instrumented accelerometers and high speed video cameras. The velocities determined from pre-crash data of EDRs and the maximum change in velocity, delta-V, and delta-V time history data obtained from post-crash data of EDRs are analyzed. The results are as follows: - Pre-crash velocities of EDRs were very accurate and reliable. An average difference between the EDR recording values and reference speeds was 4.2% and a root mean square of the differences was 9.2%. Only two cases resulted large differences for the pre-crash velocity. Both of them were cases with braking prior to the collision. However, another test with braking resulted less difference. The braking condition may influence accuracy of pre-crash velocities. - Maximum delta-Vs obtained from the EDRs showed uncertainty of measurement in several cases in comparisons with the reliable delta-V data. The differences in maximum delta-V were more than 10% in five of twenty-five events data and more than 20% in two of twenty-five events data. An average of the all differences was about 4% and root mean square of the differences was about 11%. Especially large deformation at narrow area may influence accuracy of post-crash delta-V. - Multiple rear-end crash tests were reconstructed using EDRs data as case studies. Some EDRs recorded two events and a time gap between two events, so that these reconstruction case studies were very accurate and reliable. - If though only one of three vehicles in multiple rear end crash was equipped EDR, overview and velocities of all cars may be reconstructed using these limited EDR data. In this case study, leading car- EDR data and middle car- EDR data were valuable. However if only following car was equipped EDR, the reconstruction was not accurate
Small overlap frontal crashes are defined by a damage pattern with most of the vehicle deformation concentrated outboard of the main longitudinal structures. These crashes are prominent among frontal crashes resulting in serious and fatal injuries, even among vehicles that perform well in regulatory and consumer information crash tests. One of the critical aspects of understanding these crashes is knowing the crash speeds that cause the types of damage associated with serious injuries. Laboratory crash tests were conducted using 12 vehicles in three small overlap test conditions: pole, vehicle-to-vehicle collinear, and vehicle-to-vehicle oblique (15-degree striking angle). Field reconstruction techniques were used to estimate the delta V for each vehicle, and these results were compared with actual delta V values based on vehicle accelerometer data. Estimated delta Vs were 50% lower than actual values. Velocity change estimates for small overlap frontal crashes in databases such as NASS-CDS significantly underestimate actual values.
Although the statistics show a decreasing rate of child injuries and fatalities in German road accidents more efforts can be made to protect children in cars e.g. by developing appropriate child restraint systems. An important part in of this work can be achieved with the help of crash tests using child dummies. However these crash tests cannot completely reflect the situation of real world crashes as factors like children moving out of the optimal position or children incorrectly fastened by their parents are difficult to predict. Therefore this study gives an overview over the current accident and injury situation of child occupants in cars in German road accidents.
Accidents involving two wheels vehicles represent one of the more important types of accidents in Europe. These accidents are usually not easy to reconstruct specially for the analysis of the injuries and its correlation with accident dynamics and evidences. Different methodologies are applied in this work for the reconstruction of two wheeler accidents, especially accident involving motorcycles. From the typologies of road evidences like skid marks, to the use of Pc-Crash and the use of Madymo models, different reconstruction of real accidents are presented. One of the questions that sometimes arise for legal purposes when some type of head injuries arise is if the occupant was wearing or not a helmet. The correlation of head injuries with the use of the helmet is a very important issue, therefore an important legal aspect. One of the key questions for the reconstructions that is difficult to analyze, is if the vehicle occupant, was or not, wearing the helmet. Based on the previously collected information, a generic model of a helmet was developed on CAD 3D, followed by its conversion into finite elements, all in order to perform impact tests using the Madymo software that would help improve the helmet- safety, but that also can be used as a tool in accident reconstruction.
Females sustain Cervical Spine Distortion injury (CSD) more often than males. Most work dealing with the biomechanics background (e.g. injury mechanism/criteria) as well as the application in seat design/testing, focuses on the occupant model of an average male. Therefore the EU-Project ADSEAT (Adaptive Seat to Reduce Neck Injuries for Female and Male Occupants) is aimed at adding a female model for gender balanced research of CSD and improving seat design. An extensive literature review, searching for risk factors and injury criteria for males and females, was accompanied by the evaluation of different databases containing CSD cases. The database evaluations suggests that an anthropometry quite close to the 50%ile female anthropometry as known from crash test dummy design is appropriate. The results presented here form the basis for the future development of a computational female model and the improvement of seat design for better protection of both males and females in the frame of the ADSEAT-Project.
Impact severity is a fundamental measure for all in-depth crash investigation projects. One methodology used in the UK is based on the US Calspan software package CRASH3. The UK- in-depth crash investigation studies routinely use AiDamage3 a software package which is based on an updated version of the original CRASH3 algorithm, including enhancements to the vehicle stiffness coefficients. Real world accident-damaged vehicles are measured and their crush is correlated with a library of stiffness coefficients. These measurements are then used, along with other parameters, to calculate the crash energy and equivalent changes of velocity of the vehicles (delta-v), which is a measure of the impact severity. UK in-depth accident studies routinely validate the crash severity methodologies applied as the vehicle fleet changes. This is achieved by analysing crash test data and using the appropriate residual crush damage and other inputs to AiDamage3 and checking the program- outputs with the known crash severity parameters. This procedure checks, at least in part, the default stiffness values in the data libraries and the reconstruction methods used.
This study updates previous IIHS studies comparing estimated delta Vs for crash tested vehicles to the distribution of estimated delta Vs in the National Automotive Sampling System (NASS) Crashworthiness Data System (CDS). The delta V estimates for 232 frontal crash tests at 64.4km/h into a deformable barrier with 40 percent overlap are compared with estimates from frontal offset crashes in the 1997-2004 NASS database. All delta V estimates were based on SMASH, the delta V estimating program used by NASS since 1997. Results indicated that for all vehicles tested by IIHS, SMASH delta Vs were, on average, 32 percent lower than impact speeds and about 28 percent lower than the expected delta V. Almost 80 percent of all real-world frontal crashes resulting in AIS 3+ injuries and just over 60 percent of all fatal crashes occur at or below the average estimated delta V calculated for crash tested vehicles.