91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
Volltext vorhanden
- nein (23) (entfernen)
Schlagworte
- Safety (23) (entfernen)
Institut
- Sonstige (23) (entfernen)
Gegenstand der Studie ist die Sicherheitsbeurteilung kleiner Stadt-Pkw. Durch die Auswertung von Herstellerunterlagen zur konstruktiven Gestaltung, von Veröffentlichungen zum Kollisionsverhalten und zur Betriebssicherheit, in Kontakten mit einem Importeur solcher Fahrzeuge und durch eigene Begutachtung mehrerer Modelle wurde der technische Stand gegenwärtig angebotener Fahrzeuge erfasst. Die rechtliche Situation der Fahrzeuge in der Bundesrepublik Deutschland, Frankreich, Italien und Japan wurde zusammengestellt. Die gesetzlichen Anforderungen dieser Staaten an diesen Fahrzeugen unterscheiden sich deutlich. Europäische Fahrzeuge berücksichtigen nur in geringem Maß Belange der passiven Sicherheit, da die Fahrzeuge in ihren Herstellungsländern Vorschriften zum Aufprallverhalten und zum Insassenschutz nicht erfüllen müssen. Japanische Fahrzeuge sind in ihren Eigenschaften herkömmlichen Fahrzeugen ähnlich. Wichtige Anforderungen an die innere und äussere passive Sicherheit dieser Stadt-Pkw werden zusammengestellt.
Seit Anfang der 70er Jahre kann im Bereich der passiven Sicherheit eine stetige Verbesserung durch die Abnahme der im Verkehr verletzten und getöteten Personen beobachtet werden. Weitere fahrzeugtechnische Optimierungen zur Verbesserung von Selbst- und Partnerschutz, unterstützt und forciert durch flankierende legislative Maßnahmen, sind durchzuführen, wobei parallel die Effizienz bereits getroffener Maßnahmen zu prüfen ist. In der Pilotstudie wird der Versuch gemacht, ausgehend von bekannten Erkenntnissen der Unfallanalyse, das Gesamtunfallgeschehen Pkw zu realitätsbezogenen, in ihren Wirkungsmechanismen gleichartigen Unfallkonstellationen zusammenzufassen. Die Reduzierung auf wenige Kollisionstypen schafft die Möglichkeit zur Erarbeitung von Testbedingungen. Die im Test nachzufahrenden Unfallkonstellationen und die statisch/dynamische Untersuchung einzelner Fahrzeugkomponenten dokumentieren sich in physikalischen Messwerten und fahrzeugbezogenen Größen. Ein Bewertungssystem addiert die Messwerte auf und versieht sie mit relevanzproportionalen Wichtungsfaktoren zu einem Sicherheitsgrad. Praktische Bedeutung hat das Projekt zum Beispiel für die quantitative Ermittlung des Sicherheitsfortschrittes innerhalb eines Zeitraumes von 10 bis 15 Jahren, der Untersuchung von Sicherheitskomponenten und der Effizienzüberprüfung legislativer Sicherheitsverordnungen etc.
Ziel des Projektes war die Untersuchung der fahrdynamischen Besonderheiten der stationären, besonders jedoch der instationären Kurvenfahrt (Kurvenbremsung) von einspurigen Kraftfahrzeugen. Hierbei waren die Bewertung von Bremswirkung und Fahrstabilität unterschiedlicher Bremssysteme (Standardbremse, Kombibremse, ABV-Systeme) bei Kurvenbremsung sowie die Quantifizierung fahrer-, fahrzeug-, und fahrbahnseitiger Einflussparameter von besonderer Bedeutung. Hierzu werden zunächst die physikalischen und fahrdynamischen Grundlagen erarbeitet und der theoretische Ablauf der Kurvenbremsung betrachtet. Es folgte die experimentelle Erfassung des Kurvenbremsverhaltens im Straßenfahrversuch unter Verwendung der unterschiedlichen Bremssysteme und der Variation aller relevanter Parameter. Anschließend erfolgte die rechnergestützte Auswertung der experimentellen Ergebnisse sowie die Bewertung der unterschiedlichen Bremssysteme und Einflussgrößen. Als wichtigste Ergebnisse der Untersuchung können folgende Punkte gelten: - Alle untersuchten Bremssysteme können hinsichtlich des querdynamischen Verhaltens (Kurshaltung, Fahrstabilität) nicht befriedigen. - Effiziente Abbremsung in Kurvenfahrt mit ausreichender Bremssicherheit ist mit einer ABV-geregelten Kombibremsanlage zu erreichen unter der Voraussetzung, dass die ABV-Regelung nicht aktiviert wird, sondern das ABV-System lediglich als Überbremsungsschutz fungiert. - Die herkömmliche ungeregelte Standardbremse birgt mit zunehmender Querbeschleunigung eskalierende Sturzrisiken. Beim derzeitigen Stand der Technik lassen ABV-Systeme eine ausreichend fahr- und kursstabile Kurvenbremsung mit befriedigender Verzögerung zu, wenn nahe an der Regelungsschwelle gebremst wird. Wegen des hierbei dominierenden Einflusses des Vorderrades ist die Verbindung eines auf beide Räder wirkenden ABV-Systems mit einer lastabhängigen Kombibremse und voreilend überbremstem Hinterrad zu empfehlen.
Sicherheitstechnische Anforderungen an die Bestuhlung moderner Reisebusse als Rückhaltesysteme
(1991)
Die Schutzfähigkeit von KOM-Fahrgastsitzen, die den ECE-R 80-Anforderungen entsprechen, ist bisher nur für die aufgerichtete Rückenlehne nachgewiesen. Hier wurde untersucht, ob auch geneigte Rückenlehnen ausreichende Schutzwirkung bieten. Ausgehend von der Normalsitzposition verfügen Reisebussitze heutiger Bauart über einen Lehnenverstellwinkel von circa 15 Grad (Normal-, Ruhesitzposition). Sondersitze für Ältere und Sportler erlauben auch die Liegesitz- beziehungsweise Liegeposition bei jedoch erheblich größeren Sitzteilern. In Schlittenaufprallversuchen mit je zwei instrumentierten anthropometrischen Messpuppen auf Reisebus-Doppelsitzen wurden die Belastungsverhältnisse eines frontalen Aufpralls simuliert. Die Lehnenverstelleinrichtung der Prüfsitze wurde behelfsweise so verändert, dass 3 (4) Winkeleinstellungen der Lehnenneigung möglich waren. Für jeweils zwei hintereinander zugeordnete Sitzplätze wurden wechselweise diese Lehneneinstellungen variiert. Mit 17 Doppelsitzen wurden insgesamt 32 Körperaufprallereignisse in den verschiedenen Lehnenneigungskonfigurationen durchgeführt. Die Versuchsergebnisse gliederten sich nach der Bewegungsform des Dummy, seinen Belastungen und den am Vordersitz hervorgerufenen Beschädigungen. Die Aufprallverhältnisse in aufrechter Normalsitzposition entsprechend der ECE-R 80 bildeten die Bewertungsbasis. Die gewonnenen Versuchsergebnisse lassen sich wie folgt zusammenfassen: - Für beliebige Lehneneinstellungen im Winkelbereich bis zu 30 Grad zur Senkrechten bietet die vorgebaute Sitzlehne generell ausreichende Rückhaltewirkung beim Körperaufprall. - Wenn die Vordersitzlehne jedoch steiler eingestellt ist als es der Körperhaltung des dahintersitzenden Dummy entspricht, ist mit 1,5-2fach höheren Kopfbelastungen zu rechnen. Das ECE-R 80-Schutzkriterium HAC < 500 wird überschritten. - Vorsorglich sollte aus sicherheitstechnischer Sicht der zulässige Grenzwinkel der Lehnenneigung auf 30 Grad zur Senkrechten beschränkt werden.
Das Ziel des Forschungsprojekts "Quantifizierung der Passiven Sicherheit für Pkw-Insassen" besteht darin, Messergebnisse in Form von Dummybelastungswerten zu einem Sicherheitsindex zu verdichten. Zur Formulierung des dazu erforderlichen Bewertungsalgorithmus wurden folgende Zusammenhänge erarbeitet: 1. Beziehung zwischen Verletzungsschwere und Dummybelastungsgröße für relevante Körperteile, 2. Relevanzfaktoren zur Wichtung der Teilergebnisse und 3. Zusammenhang zwischen körperteilspezifischen Schutzkriterien und dem entsprechenden Erfüllungsgrad. Die wesentliche Aufmerksamkeit erforderte die Bereitstellung der Relevanzstruktur, da mit den einzelnen Relevanzfaktoren die gemessenen Belastungen entsprechend der Bedeutung der im realen Unfallgeschehen beobachteten Verletzungen bewertet werden sollten. Im Bereich der experimentellen Simulation lag das Hauptaugenmerk auf der Bereitstellung der Versuchsbedingungen, wobei die gesetzlich vorgeschriebenen Sicherheitsversuche zu berücksichtigen waren. Daraus ergab sich die Festlegung auf folgende Versuchskonstellationen: 1. Frontaler Wandaufprall, 2. Seitenaufprall einer fahrbaren Barriere auf den stehenden Pkw und 3. Kompatibilitätsversuch, bei dem ein Fahrzeug seitlich mit einem anderen Fahrzeug gleichen Typs kollidiert. Mit Hilfe eines erarbeiteten Bewertungsalgorithmus werden die versuchstechnisch gemessenen Belastungswerte normiert und der Bewertungsfunktion zugeführt. Die so ermittelten Erfüllungsgrade erhalten durch die Relevanzfaktoren eine unfallspezifische Wichtung und lassen sich über Teilsicherheitsindizes zu einem Gesamt-Sicherheitsindex zusammenfassen. Dieser Sicherheitsindex soll Aufschluss über das Niveau der inneren Sicherheit von Pkw geben.
Für eine quantitativ exakte Beschreibung der mit der Gefahrgutbeförderung verbundenen Risiken fehlen sowohl statistische Voraussetzungen als auch eine wissenschaftlich begründete Risikoanalyse. Eine Risikoanalyse der Gefahrgutbeförderung soll zweckmäßigerweise auf Transportketten und nicht auf den direkten Vergleich von Verkehrsträgern abstellen. Zentrale Kategorie zur Definition des Risikos sollte dabei der Unfall sein. Zusammen mit der Transportleistung sollte er das Risiko als Wahrscheinlichkeitsaussage beschreiben. Mit in die Risikobestimmung einzubeziehen ist die Unfallschwere. Im Rahmen des Beitrages schlägt eine Projektgruppe eine dreistufig angelegte Risikoanalyse vor. Die Bausteine dieser Risikoanalyse bestehen aus 1. einer mathematisch-statistischen Risikoanalyse, 2. einer Schwachstellenanalyse und 3. einem Systemmodell zur ständigen Analyse des Gefahrgutbeförderungsrisikos. Dazu werden in dem Forschungsbericht grundsätzliche Überlegungen zur Risikobewertung angestellt, auf das Regelwerk des Gefahrguttransportes eingegangen, Ausbildung, Training und Überprüfung der Fahrzeugführer behandelt sowie auf das Gefahrgut und die Gefahrgutumschließung eingegangen. Ferner befasst sich der Bericht mit der Fahrzeugtechnik, der Verkehrsinfrastruktur, Informationssystemen und der Sicherheit im Gefahrguttransport in den neuen Bundesländern. Zum Schluss werden Forschungsempfehlungen bezüglich der Sicherheit in der Gefahrgutbeförderung formuliert.
In Form einer Pilotstudie wurden eine Literaturrecherche, eine Befragung von Experten der Automobilindustrie und theoretische Untersuchungen zur Frage der Head-Up-Display-Technik (HUD) im Kraftfahrzeug durchgeführt. Auf der Suche nach neuen, die Sicherheit des Kraftfahrzeugverkehrs fördernden Anzeigen findet das HUD zunehmend Interesse. Das Prinzip des HUD im Kraftfahrzeug besteht darin, dass die Informationen des Displays über den in die Windschutzscheibe integrierten Combiner in die Verkehrsszene als virtuelles Bild eingeblendet werden. In Europa wurden von Automobil- und Zulieferfirmen ca. ein Dutzend HUD-Systeme als Experimentalsysteme entwickelt. In den europäischen Forschungsprogrammen PROMETHEUS und DRIVE wird das HUD als eine von mehreren neuen Anzeigetechniken untersucht. In den USA und Japan befinden sich HUD-Systeme in Serienfahrzeugen bereits seit einigen Jahren auf dem Markt. Informationen auf einem HUD im Kraftfahrzeug werden schneller und sicherer abgelesen, als auf der konventionellen Instrumententafel. Insbesondere die physiologischen Anteile des Wahrnehmungsvorganges, das heißt die Augenbewegung, das Akkommodieren und das Adaptieren, erfolgen mit einem HUD schneller. Allerdings kann die Verquickung der Verkehrsszene mit bordeigenen Informationen zu verändertem Fahrverhalten und zu anderen Beobachtungsstrategien der Kraftfahrer führen. Die HUD-Technik ist zwar relativ fortgeschritten, jedoch liegen nur wenige fundierte experimentelle Ergebnisse vor. Es wurde daher eine Untersuchungsreihe mit Labor-, Simulator- und Feldexperimenten entworfen, die offene Fragen zu Nutzen, Informationsinhalten und Gestaltung von HUD-Anzeigen beantworten sollen. Gesetzliche Vorschriften der StVZO und die sie tangierenden EG-Richtlinien beziehungsweise ECE-Regelungen legen die Mindestanforderungen an die Sicht aus Kraftfahrzeugen fest, und es bestehen Vorgaben sowohl für die mögliche Position der HUD-Anzeigen, als auch für die Transmission und für die Farberkennung der Verkehrsobjekte.
Die vorliegende Studie untersucht die Auswirkung der Ausstattung von Motorrädern mit Anti-Blockier-System (ABS) auf die Fahrsicherheit von Motorrädern. Hierzu wurden Fahrversuche im realen Verkehr und auf abgesperrter Teststrecke durchgeführt. Erfahrene und wenig erfahrene Motorradfahrer absolvierten Testfahrten auf nasser und trockener Fahrbahn mit und ohne ABS-Aktivierung des Motorrades. Bei den Versuchsfahrten kam es zu einigen kritischen Fahrsituationen, bei denen die Versuchspersonen insbesondere zu Beginn des Bremsmanövers von ihrem "normalen" Bremsverhalten abwichen. Bei blockierendem Hinterrad wurde der Bremsdruck vorne und hinten reduziert, was zu einer deutlichen Bremswegverlängerung führte. Bei den Vollbremsungen unter idealen Bedingungen auf abgesperrter Strecke wurden von erfahrenen Fahrern ohne ABS kürzere Bremswege als mit ABS erreicht. Kurvenbremsungen mit ABS-Regelung wurden im mittleren Geschwindigkeits- und Schräglagebereich fahrstabil durchgeführt. Die Ergebnisse zeigen, dass selbst erfahrene Motorradfahrer Bremsweg in kritischen Situationen verschenken. Geeignete Antiblockiersysteme könnten Motorradfahrern die Angst vor Radblockaden nehmen. Dies dürfte einen erheblichen Beitrag zur Steigerung der aktiven Sicherheit leisten.
Wegen der wachsenden Verbreitung von Fahrradanhängern zum Kindertransport und der möglichen Unfallgefährdung ist im vorliegenden Forschungsprojekt deren passive Sicherheit untersucht worden. Zudem wurde der Frage nachgegangen, ob der Transport von Kindern im Fahrradanhänger sicherer ist als mit dem Fahrrad mit Kindersitzen. In Absprache mit Herstellern und Vertreibern wurden verschiedene Untersuchungen durchgeführt. Es handelte sich um Anprallversuche (Anfahrversuche), Rollwagenversuche (Schlittenversuche) sowie Kopffreiheitsprüfungen und Fallversuche. Bei den Versuchen waren die Prüfobjekte mit einem oder zwei Dummies besetzt, die mit Messdatenaufnehmern ausgestattet waren. Verschiedene Messdaten, zum Beispiel Kopf- und Brustbeschleunigung, wurden erfasst und ausgewertet. Zusätzlich wurde das Kopfschutzkriterium (HPC) berechnet und bewertet. Entstandene Schäden an den Prüfobjekten wurden aufgenommen und durch Fotos dokumentiert. Die Versuchsabläufe selbst wurden mit Hochgeschwindigkeitskameras aus verschiedenen Positionen aufgezeichnet. Beim Anfahrversuch mit einem Pkw gegen ein Gespann aus Fahrrad und Anhänger waren direkte Anstöße der Anhängerinsassen an die Pkw-Front zu erkennen. Die Beschleunigungswerte waren dabei relativ hoch. Anstöße gegen Anhängerinnenteile waren bei fast allen Versuchen zu beobachten. Teilweise wurden Radaufhängungen und Radnaben beschädigt. Durch die Rollwagenversuche wurden konstruktive Schwächen bei den Sitzen und Rückhaltesystemen festgestellt. Nähte, Befestigungen und Verstellösen wurden zerstört. Es stellte sich heraus, dass die Qualität des Gurtsystems, die Steifigkeit des Anhängeraufbaus, die Sitzposition der Kinder und die vorhandene Kopffreiheit ausschlaggebend für das Verletzungsrisiko der Insassen sind. Bei den Versuchen mit Fahrradsitzen ergaben sich hohe Beschleunigungswerte durch den direkten Kontakt des Radfahrers mit der Fahrzeugfront und/oder der Fahrbahn. Das Gewicht des Radfahrers, des Fahrrades und auch Fahrradteile bergen ein erhöhtes Verletzungsrisiko für das Kind. Zusätzlich besteht die Gefahr überfahren zu werden, wenn das Kind nach dem Sturz des Fahrrades ungeschützt auf der Fahrbahn liegt. Ein direkter Vergleich der beiden Transportmöglichkeiten war aufgrund der geringen Daten der Versuche mit Fahrradkindersitzen nur bedingt möglich. Tendenziell ist der Transport der Kinder im Fahrradanhänger als weniger gefährlich zu bewerten. Es werden die Vor- und Nachteile dargestellt. Zur Bewertung der Sicherheit von Fahrradanhängern wurden die folgenden Prüfmethoden erarbeitet: - Pendelschlagprüfung für die gesamte Chassisstruktur; - Kopffreiheitsprüfung; - Belastungsprüfung der Aufbaustruktur; - Festigkeitsprüfung der Gurtsysteme. Die Prüfungen sind so aufgebaut, dass sie mit einfachen Mitteln durchzuführen sind. Es sollte somit jedem Anhängerhersteller möglich sein, die passive Sicherheit seiner Produkte umfassend zu untersuchen. Die Prüfverfahren für die Sicherheitsbewertung sollen in eine DIN-Norm und in das Merkblatt für Fahrradanhänger einfließen. Der Original-Forschungsbericht enthält einen umfangreichen Fotoband zu den Einzelheiten der Versuche und Versuchsaufbauten sowie zu den Beschädigungen der Prüfobjekte und kann bei der BASt eingesehen werden.
A means of assessing the passive safety of automobiles is a desirable instrument for legislative bodies, the automobile industry, and the consumer. As opposed to the dominating motor vehicle assessment criteria, such as engine power, spaciousness, aerodynamics and consumption, there are no clear and generally accepted criteria for assessing the passive safety of cars. The proposed method of assessment combines the results of experimental safety tests, carried out according to existing legally prescribed or currently discussed testing conditions, and a biomechanical validation of the loading values determined in the test. This evaluation is carried out with the aid of risk functions which are specified for individual parts of the body by correlating the results of accident analysis with those obtained by computer simulation. The degree of conformance to the respective protection criterion thus deduced is then weighted with factors which take into account the frequency of occurrence and the severity of the accident on the basis of resulting costs. Each of the test series includes at least two frontal and one lateral crash test against a deformable barrier. The computer-aided analysis and evaluation of the simulation results enables a vehicle-specific overall safety index as well as partial and individual safety values to be determined and plotted graphically. The passive safety provided by the respective vehicle under test can be defined for specific seating positions, special types of accident, or for individual endangered parts of the body.
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 13. Oktober 2006 in Baden-Baden das 6. Symposium "Sicher fahren in Europa". Die Fachvorträge befassten sich mit den Themenbereichen: Ansätze zu mehr Verkehrssicherheit, - Verbesserung der Fahrzeugsicherheit, - Besondere Zielgruppen. Die CD-ROM dokumentiert die Grußworte, die Referate und die Podiumsdiskussion.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
In 2012 the fifth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
To improve vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility aims to improve both the self and partner protection properties of vehicles. Although compatibility has received worldwide attention for many years, no final assessment approach has been defined. Within the Frontal Impact and Compatibility Assessment Research (FIMCAR) project, different frontal impact test procedures (offset deformable barrier [ODB] test as currently used for Economic Commission for Europe [ECE] R94, progressive deformable barrier test as proposed by France for a new ECE regulation, moveable deformable barrier test as discussed worldwide, full-width rigid barrier test as used in Federal Motor Vehicle Safety Standard [FMVSS] 208, and full-width deformable barrier test) were analyzed regarding their potential for future frontal impact legislation. The research activities focused on car-to-car frontal impact accidents based on accident investigations involving newer cars. Test procedures were developed with both a crash test program and numerical simulations. The proposal from FIMCAR is to use a full-width test procedure with a deformable element and compatibility metrics in combination with the current offset test as a frontal impact assessment approach that also addresses compatibility. By adding a full-width test to the current ODB test it is possible to better address the issues of structural misalignment and injuries resulting from high acceleration accidents as observed in the current fleet. The estimated benefit ranges from a 5 to 12 percent reduction of fatalities and serious injuries resulting from frontal impact accidents. By using a deformable element in the full-width test, the test conditions are more representative of real-world situations with respect to acceleration pulse, restraint system triggering time, and deformation pattern of the front structure. The test results are therefore expected to better represent real-world performance of the tested car. Furthermore, the assessment of the structural alignment is more robust than in the rigid wall test.
The goal of the project FIMCAR (Frontal Impact and Compatibility Assessment Research) was to define an integrated set of test procedures and associated metrics to assess a vehicle's frontal impact protection, which includes self- and partner-protection. For the development of the set, two different full-width tests (full-width deformable barrier [FWDB] test, full-width rigid barrier test) and three different offset tests (offset deformable barrier [ODB] test, progressive deformable barrier [PDB] test, moveable deformable barrier with the PDB barrier face [MPDB] test) have been investigated. Different compatibility assessment procedures were analysed and metrics for assessing structural interaction (structural alignment, vertical and horizontal load spreading) as well as several promising metrics for the PDB/MPDB barrier were developed. The final assessment approach consists of a combination of the most suitable full-width and offset tests. For the full-width test (FWDB), a metric was developed to address structural alignment based on load cell wall information in the first 40 ms of the test. For the offset test (ODB), the existing ECE R94 was chosen. Within the paper, an overview of the final assessment approach for the frontal impact test procedures and their development is given.
Established in 1997, the European New Car Assessment Programme (Euro NCAP) provides consumers with a safety performance assessment for the majority of the most popular cars in Europe. Thanks to its rigorous crash tests, Euro NCAP has rapidly become an important driver safety improvement to new cars. After ten years of rating vehicles, Euro NCAP felt that a change was necessary to stay in tune with rapidly emerging driver assistance and crash avoidance systems and to respond to shifting priorities in road safety. A new overall rating system was introduced that combines the most important aspects of vehicle safety under a single star rating. The overall rating system has allowed Euro NCAP to continue to push for better fitment and higher performance for vehicles sold on the European market. In the coming years, the safety rating is expected to play an important role in the support of the roll-out of highly automated vehicles.
Motorcycling is a fascinating kind of transportation. While the riders' direct exposure to the environment and the unique driving dynamics are essential to this fascination, they both cause a risk potential which is several times higher than when driving a car. This chapter gives a detailed introduction to the fundamentals of motorcycle dynamics and shows how its peculiarities and limitations place high demands on the layout of dynamics control systems, especially when cornering. The basic principles of dynamic stabilization and directional control are addressed along with four characteristic modes of instability (capsize, wobble, weave, and kickback). Special attention is given to the challenges of braking (brake force distribution, dynamic over-braking, kinematic instability, and brake steer torque induced righting behavior). It is explained how these challenges are addressed by state-of-the-art brake, traction, and suspension control systems in terms of system layout and principles of function. It is illustrated how the integration of additional sensors " essentially roll angle assessment " enhances the cornering performance in all three categories, fostering a trend to higher system integration levels. An outlook on potential future control systems shows exemplarily how the undesired righting behavior when braking in curves can be controlled, e.g., by means of a so-called brake steer torque avoidance mechanism (BSTAM), forming the basis for predictive brake assist (PBA) or even autonomous emergency braking (AEB). Finally, the very limited potential of brake and chassis control to stabilize yaw and roll motion during unbraked cornering accidents is regarded, closing with a promising glance at roll stabilization through a pair of gimbaled gyroscopes.
The levels of continuous vehicle automation have become common knowledge. They facilitate overall understanding of the issue. Yet, continuous vehicle automation described therein does not cover "automated driving" as a whole: Functions intervening temporarily in accident-prone situations can obviously not be classified by means of continuous levels. Continuous automation describes the shift in workload from purely human driven vehicles to full automation. Duties of the driver are assigned to the machine as automation levels rise. Emergency braking, e.g., is obviously discontinuous and intensive automation. It cannot be classified under this regime. The resulting absence of visibility of these important functions cannot satisfy " especially in the light of effect they take on traffic safety. Therefore, in order to reach a full picture of vehicle automation, a comprehensive approach is proposed that can map out different characteristics as "Principle of Operation" at top level. On this basis informing and warning functions as well as functions intervening only temporarily in near-accident situations can be described. To reach a complete picture, levels for the discontinuous, temporarily intervening functions are proposed " meant to be the counterpart of the continuous levels already in place. This results in a detailed and independent classification for accident-prone situations. This finally provides for the visibility these important functions deserve.
The term driver assistance systems in the chapter title shall be understood to include vehicle automation. This chapter starts with a homogeneous and consistent classification and nomenclature of all kinds of driver assistance systems known and under discussion today (including vehicle automation). It thereby builds upon familiar classification schemes by the German Federal Highway Research Institute (BASt) and the standardization body SAE international. Detailed evaluation of the German legal situation for driver assistance systems and vehicle automation is provided in the following Sect. 2. In Sect. 3, an overview is given on the legal system in the US to reveal aspects relevant for vehicle automation. This is intended as initial information for those not acquainted to the US legal system which has been the first to regulate automation in several federal states. Finally, in Sect. 4, the current rating scheme of the European New Car Assessment Programme (EuroNCAP) is presented in comparison to legal instruments. The model of a consumer protection based approach proves to be a flexible instrument with great advantages in promoting new technologies. Technical vehicle regulations on the other hand rule minimum requirements. Both approaches are needed to achieve maximum vehicle safety.