91 Fahrzeugkonstruktion
Filtern
Dokumenttyp
- Konferenzveröffentlichung (7)
- Buch (Monographie) (4)
- Arbeitspapier (1)
Schlagworte
- Cost benefit analysis (12) (entfernen)
Institut
Sicherheitsgurte sind als wirksamer Schutz für Pkw-Insassen bei Verkehrsunfällen weltweit anerkannt; trotzdem werden sie in der Bundesrepublik Deutschland von den Autofahrern noch nicht im wünschenswerten Maße benutzt, obwohl Sicherheitsgurte in ihren Fahrzeugen eingebaut sind. Von dieser Situation ausgehend behandelt die vorliegende Studie sowohl die wirtschaftlichen, rechtlichen und technischen Aspekte, einschließlich alternativer Rückhaltesysteme, als auch die Frage nach der Wirksamkeit des Sicherheitsgurtes. Die Auswertung der internationalen Literatur und die Erörterung der anstehenden Probleme mit Experten führten zu folgenden Feststellungen: - Der Dreipunktgurt kann sowohl hinsichtlich seines Bedienungs- und Tragekomforts als auch im Hinblick auf die beabsichtigte Schutzwirkung im Detail verbessert werden. - Derzeit gibt es keine serienreifen Alternativen zum Gurtsystem. - Das Risiko von gurtbedingten Verletzungsverschlimmerungen ist gering, so dass ihm keine ausschlaggebende Bedeutung beigemessen werden kann. - Ausländische Erfahrungen zeigen, dass durch die Einführung eines Bußgeldes die Kraftfahrer in ihrer überwiegenden Mehrheit die Anlegepflicht befolgen. - Würden in der Bundesrepublik Deutschland alle Frontinsassen von Pkw den Gurt stets anlegen, so könnte der derzeitige Sicherheitsgewinn praktisch verdoppelt werden.
Die Beurteilung der technischen und unfallrelevanten Eigenschaften der beiden Scheibenarten zeigt, dass die VSG-Scheibe gegenüber der ESG-Scheibe hinsichtlich der Verletzungs- und Unfallgefahr zwar überwiegend Vorteile aufweist; diese Vorteile sind jedoch vor allem vor dem Hintergrund steigender Gurtanlegequoten nicht als so entscheidend anzusehen, dass daraus die Begründung für ein Verbot der ESG-Scheibe abzuleiten wäre. Diese Feststellung wird insbesondere auch gestützt durch eine Nutzen-Kosten-Betrachtung, die zeigt, dass aus gesamtwirtschaftlicher Sicht bei einem generellen Ersatz der ESG-Scheibe durch die teurere VSG-Scheibe bei günstigen Annahmen der Nutzen unter den Kosten liegen würde.
In der BRD hatten 1977 etwa 39.000 bis 46.000 Pkw einen Brandschaden durch Flammen- und/oder Glutwirkung. Der Sachschadenaufwand der Kraftfahrzeugversicherer betrug 52 Mio. DM. Schwere Personenschäden sind vorwiegend bei unfallbezogenen Fahrzeugbränden entstanden. 1977 wurden ca. 55 bis 80 Personen durch Fahrzeugbrand getötet, maximal 450 schwer verletzt. Etwa 90 % der Brände entstehen infolge technischer Mängel, Fahrlässigkeit und Brandstiftung. Auf Wunsch der Käufer werden etwa 10 % der Pkw mit tragbaren Feuerlöschern ausgerüstet. Der Zwei-Kilo-Löscher hat sich als derzeit günstiger Löscher herausgestellt. Welchem Löschmittel der Vorzug zu geben ist, wurde von Experten nicht eindeutig beantwortet. Die Gesamtwirksamkeit des Zusammenhanges Brandgeschehen-Mensch-Feuerlöschgerät verdeutlicht, dass eine allgemeine Ausrüstungspflicht aller Pkw mit tragbaren Feuerlöschern aus gesamtwirtschaftlicher Sicht nicht zu befürworten ist. Das freiwillige Ausrüsten von Fahrzeugen sollte dagegen weiter propagiert werden.
Die UNECE Regelung R58 regelt die Beschaffenheit und die Installation von Heckunterfahrschutzsystemen an schweren Güterkraftfahrzeugen, deren Ziel die Verbesserung der Kompabilität zwischen Pkw-Frontstrukturen und Lkw-Hecks ist. Dennoch verunglücken laut amtlicher Unfallstatistik allein in Deutschland rund 30 Pkw-Insassen in Heckauffahrunfällen auf Lkw tödlich, da diese Vorrichtungen hinsichtlich Einbauhöhe und Steifigkeit den Anforderungen des realen Unfallgeschehens nicht genügen. Das Ziel dieser Studie ist eine quantitative Abschätzung der möglichen Reduzierung der Verletzungsschwere mit Hilfe eines statistischen Modells, die durch eine Anpassung der geltenden Bestimmungen und die damit verbundenen technischen Veränderungen des bereits vorgeschriebenen Heckunterfahrschutzes zu erreichen wäre. In einer Nutzen-Kosten-Analyse wird die Wirtschaftlichkeit dieser Modifizierungen mit einem idealen Notbremsassistenten verglichen. Die Untersuchung orientiert sich dabei an den aktuell in der UN-ECE WP29/GRSG in Genf diskutierten Vorschlägen zur Anpassung der ECE-R58. Das verwendete ordinale Probit-Modell stellt einen Zusammenhang zwischen der Verletzungsschwere im auffahrenden PKW und erklärenden Größen her, in diesem Fall der kinetischen Energie des unterfahrenden Pkws und der strukturellen lnteraktion zwischen Lkw-Heck und Pkw-Front. Diese Maßnahmen könnten demnach 53 - 78% der Getöteten sowie 27 - 49% der Schwerverletzten bei diesen Unfallkonstellationen reduzieren, was pro Jahr 20 Getöteten und 95 Schwerverletzten entsprechen würde. Somit würde eine Modifikation einer bestehenden passiven Schutzmaßnahme an jährlich 100.000 neuzugelassenen Lkw und Anhängern bereits 20 Getötete adressieren. Im Vergleich dazu müssten jährlich 3 Millionen Pkw mit zusätzlicher Sensorik und Aktuatorik für einen idealen Notbremsassistenten ausgestattet werden, um im Idealfall alle Heckauffahrunfälle von Pkw auf andere Pkw oder Lkw und damit 53 Getötete zu vermeiden. Daher fällt auch das Nutzen-Kosten-Verhältnis deutlich zugunsten des verbesserten Heckunterfahrschutzes aus.
For the estimation of the benefit and effect of innovative Driver Assistance Systems (DAS) on the collision positions and by association on the accident severity, together with the economic benefit, it becomes necessary to simulate and evaluate a variety of virtual accidents with different start values (e.g. initial speed). Taken into account the effort necessary for a manual reconstruction, only an automated crash computation can be considered for this task. This paper explains the development of an automated crash computation based on GIDAS. The focus will be on the design of the virtual vehicle models, the method of the crash computation as well as exemplary applications of the automated crash computation. For the first time an automated crash computation of passenger car accidents has been realized. Using the automated crash computation different tasks within the field of vehicle safety can be elaborated. This includes, for example, the calculation of specific accident parameters (such as EES or delta-V) for various accident constellations and the estimation of the economic benefit of DAS using IRFs (Injury Risk Functions).
A biofidelic flexible pedestrian legform impactor (FlexPLI) has been developed from the year 2000 onwards and evaluated by a technical evaluation group (Flex-TEG) of UN-ECE GRSP. A recently established UN-ECE GRSP Informal Group on GTR9 Phase 2 is aiming at introducing the FlexPLI within world-wide regulations on pedestrian safety (Phase 2 of GTR No. 9 as well as the new UN regulation 127 on pedestrian safety) as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents. Besides, the FlexPLI has already been introduced within JNCAP and is on the Euro NCAP roadmap for 2014. Despite of the biofidelic properties in the knee and tibia sections, several open issues related to the FlexPLI, like the estimation of the cost benefit, the feasibility of vehicle compliance with the threshold values, the robustness of the impactor and of the test results, the comparability between prototype and production level and the finalization of certification corridors still needed to be solved. Furthermore, discussions with stakeholders about a harmonized lower legform to bumper test area are still going on. This paper describes several studies carried out by the Federal Highway Research Institute (BASt) regarding the benefit due to the introduction of the FlexPLI within legislation for type approval, the robustness of test results, the establishment of new assembly certification corridors and a proposal for a harmonized legform to bumper test area. Furthermore, a report on vehicle tests that previously had been carried out with three prototype legforms and were now being repeated using legforms with serial production status, is given. Finally, the paper gives a status report on the ongoing simulation and testing activities with respect to the development and evaluation of an improved test procedure with upper body mass for assessing pedestrian femur injuries.
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
This work aims at bringing evidence for mass incompatibility in frontal impact for cars built according to the UNECE R94 regulation. French national injury accidents database census for years 2005 to 2008 were used for the analysis. The heterogeneity of frontal self-protection among cars of different masses is investigated, as well as the partner protection parameter offered by these cars. The last part of the analysis deals with the estimation of the benefit, in terms of fatal and severe injuries avoided, if crashworthiness was harmonized for the whole fleet of vehicle. This calculation is done for France and is extended to all Europe.
Der Vorschlag, dass alle Kraftfahrzeuge auch am Tag mit Licht fahren sollen, wird seit vielen Jahren national und international diskutiert. Aufgrund dessen hat das Bundesministerium für Verkehr, Bau- und Wohnungswesen die Bundesanstalt für Straßenwesen beauftragt, die Auswirkungen des Fahrens mit Licht am Tag auf die Straßenverkehrssicherheit in Deutschland im Rahmen eines Forschungsprojektes genauer zu untersuchen. Auf der Basis einer Bewertung der internationalen Literatur zur Wirksamkeit des Fahrens mit Licht am Tag kommt die BASt zu dem Ergebnis, dass bei obligatorischer Einführung dieser Verkehrssicherheitsmaßnahme in der Bundesrepublik Deutschland eine deutliche Verbesserung der Verkehrssicherheit erwartet werden kann. Die Unfallrückgänge liegen in einer Größenordnung von über 3%. Die Befürchtung, dass sich demgegenüber Nachteile für schwächere Verkehrsteilnehmer, insbesondere Motorradfahrer, ergeben und deren Unfallhäufigkeit steigt, konnte nicht erhärtet werden. Die obligatorische Einführung des Fahrens mit Licht am Tag ist unter gesamtwirtschaftlichen Gesichtspunkten auch effizient. Den zu erwartenden Sicherheitsnutzen in Höhe von umgerechnet 1 Mrd. € je Jahr stehen Kosten in Folge des zunehmenden Kraftstoffverbrauchs und der damit verbundenen Emissionen in Höhe von 630 Mio. € (ungünstigster Fall: Fahren mit Abblendlicht) gegenüber. Auf lange Sicht sinken mit speziellen Tagfahrleuchten diese Kosten auf 150 Mio. € (Tagfahrleuchten in Glühlampentechnik) oder sogar nur 60 Millionen Euro (Tagfahrleuchten in LED-Technik). Es wird deshalb empfohlen, - für Neufahrzeuge eine Ausrüstung mit Tagfahrleuchten mit automatischer Aktivierung, gekoppelt an die Zündung, vorzuschreiben, - sowie einen Dämmerungsschalter zur automatischen Einschaltung des Abblendlichts obligatorisch einzuführen. Um einen nachteiligen Sicherheitseffekt durch die Durchmischung mit beleuchteten und unbeleuchteten Fahrzeugen zu vermeiden, ist für Altfahrzeuge ohne spezielle Tagfahrleuchten das Fahren mit Licht am Tag ganzjährig auf dem gesamten Straßennetz dringend zu empfehlen. Die Empfehlung für den bestehenden Kraftfahrzeugbestand sollte spätestens zum Zeitpunkt der Einführung der Ausstattungsvorschrift für die Neufahrzeuge ausgesprochen werden.
At the beginning of the year 2000 the European Commission set the goal to halve the number of road deaths till the year 2010. The main focus are passenger car and lorry traffic. A significant reduction of the accident data could be reached in these groups. The advancement of active vehicle safety systems is an important issue of the programme. The safety of the motorcycle traffic has been disregarded till now. Since 1991 the number of killed motorcycle riders per year has been constant. The number of killed passenger car occupants has been more than halved in the same period. This is why initiatives are caused for the increase of the motorcycle safety. A great safety potential is expected for the Antilock Brake System (ABS). ABS for motorcycles is considered from the economic view in this study. A cost-benefit analysis shall clarify whether the economic benefit of ABS for motorcycles is greater than the consumed resources. Moreover, a sensitivity analysis will determine the maximal justifiable consumption in resource for which ABS is worthwhile. After the sensitivity analysis is done a break-even analysis will determine the market price respectively the annual mileage from which on ABS is worthwhile on user level. For this the fair end consumer market price is calculated which the user is ready to pay. For the considered market prices the annual mileage is determined from which on ABS is worthwhile for the user. The considered time horizon for this analysis are the years 2015 and 2020. For each of these years the accident data is forecasted. At this, it is assumed that the frequency of having an accident per million registered motorcycles decreases based on the present trend. Thus, riding motorcycle gets safer. Hence, the accident data in the years 2015 and 2020 is lower than the accident data today. The cost-benefit analysis is done for each year for four scenarios. Two scenarios handle the market penetration. The first one is the trend scenario, the second one is the mandatory equipment from the year 2010 on. The other scenarios describe the effectiveness of ABS. The effectiveness rates are determined by a literature review. The only potential which can be considered due to the available data is the potential due to an avoiding of the downfall just before the real accident happens. According to this the number of accidents will decrease by 2.4 %. The number of fatalities will decrease by 12.1 %. The number of severe injuries decreases by 11.7 %. However, the number of slight injuries increases by 2.1 %. The mentioned effectiveness rates are valid for the scenarios with the high effectiveness. Even these figures underestimate the actual effectiveness because there are only considered the avoided accidents with downfall. The necessary consumption in resources depends on the produced volume. The more ABS systems are produced, the lower are the costs per system. This is due to realised effects of scale and effects out of learning curves. The system costs depend on the penetration rate. In the trend scenario the system costs for ABS are 120 Euro for the year 2015 respectively 105 Euro for the year 2020. In the mandatory scenario the system costs are 115 Euro for the year 2015 respectively 100 Euro for the year 2020. The benefit-cost ratios are all over the critical barrier of 1.0. Thus, ABS is worthwhile on economic level. In the scenarios with high effectiveness the benefit-cost ratios range between 4.6 and 4.9. Thus, the values are even above the barrier of 3.0. The result of the break-even analysis is that ABS is worthwhile on user level. The considered market prices are 400 Euro in 2015 and 300 Euro in 2020. They are clearly below the determined fair end consumer market prices. The fair end consumer price for the year 2015 is 701 Euro respectively 622 Euro for the year 2020. Thus, ABS is worthwhile for motorcycle riders with an annual mileage higher than 2,200 km (year 2015) respectively 1,900 km (year 2020). The annual mileage of a motorcycle rider is 3,900 km on average. Thus, ABS is worthwhile for most of the motorcycle riders. The mentioned results are valid for the high effectiveness scenarios.