91 Fahrzeugkonstruktion
Except for corrective steering functions automatic steering is up to now only allowed at speeds up to 10 km/h according to UN Regulation No. 79. Progress in automotive engineering with regard to driver assistance systems and automation of driving tasks is that far that it would be technically feasible to realise automatically commanded steering functions also at higher vehicle speeds. Besides improvements in terms of comfort these automated systems are expected to contribute to road traffic safety as well. However, this safety potential will only be exhausted if automated steering systems are properly designed. Especially possible new risks due to automated steering have to be addressed and reduced to a minimum. For these reasons work is currently ongoing on UNECE level with the aim to amend the regulation dealing with provisions concerning the approval of steering equipment. It is the aim to revise requirements for automatically commanded steering functions (ACSF) so that they can be approved also for higher speeds if certain performance requirements are fulfilled. The paper at hand describes the derivation of reasonable system specifications from an analysis of relevant driving situations with an automated steering system. Needs are explained with regard to covering normal driving, sudden unexpected critical events, transition to manual driving, driver availability and manoeuvres to reach a state of minimal risk. These issues form the basis for the development of test procedures for automated steering to be implemented in international regulations. This holds for system functionalities like automatic lane keeping or automatic lane change as well as for addressing transition situations in which the system has to hand over steering to the driver or addressing emergency situations in which the system has to react instead of the driver.
The UN Regulation No. 79 is going to be amended to allow automatically commanded steering functions (ACSF) at speeds above 10 km/h. Hence, requirements concerning the approval of automatically performed steering manoeuvres have to be set in order to allow safe use of automatic steering on public roads as well as improve overall road safety for the driver and the surroundings. By order of the German Federal Ministry of Transport and Digital Infrastructure (BMVI), BASt developed and verified physical test procedures for automatic steering to be implemented in UN Regulation No. 79. The usability of currently available test tools was examined. The paper at hand describes these test procedures and presents results from verification tests. The designated tests are divided in three sections: functionality tests, verifications for the transition of control and emergency tests. System functionality tests are auto matic lane keeping, automatic lane change and an automatic abort of an initiated lane change due to traffic. Those tests check if the vehicle remains in its lane (under normal operating conditions), is able to perform safe automatic lane change manoeuvres and if it considers other road users during its manoeuvres. Transition tests examine the vehicle's behaviour when the driver fails to monitor the system and in situations when the system has to hand over the steering control back to the driver. For instance these tests provoke driver-in-the-loop requests by approaching system boundary limitations, like missing lane markings, surpassing maximum lateral acceleration in a bend or even a major system failure. Even further the driver and his inputs are monitored and if the system detects that he is overriding system actions or contrary want to quit the driving task and unfastens the seat belt, it has to shut down and put the human back into manually control and the responsibility of driving. The last series of test consists of two emergency situations in which the system has to react to a time critical event: A hard decelerating vehicle and a stationary vehicle in front both with no lane change possibility for the ACSF vehicle. Some of the tests, especially the emergency manoeuvres, require special target vehicles and propulsion systems. Since no fully automatic steering vehicles are available, a current Mercedes E-Class with Mercedes' "drive pilot" system was used. It was shown that the vehicle is automatically able to brake to a full stop towards a static Euro NCAP target from partial-automatic driving at 90 km/h, that it could brake towards a rapidly decelerating lead vehicle when travelling at 70 km/h, that it was able during partially automatic driving to remain in its lane in normal operation conditions and to perform a automatic (driver initiated) lane change while surveilling the driver- activities.
Automatische Lenkfunktionen sind abgesehen von korrigierenden Lenkeingriffen entsprechend der UN-Regelung Nr. 79 bisher nur in einem Geschwindigkeitsbereich bis 10 km/h erlaubt. Die Weiterentwicklung der Technik im Bereich der Fahrerassistenzsysteme und der Automatisierung der Fahraufgabe wuerden es jedoch technisch erlauben, automatische Lenkfunktionen auch bei höheren Geschwindigkeiten einzusetzen. Neben einem Zugewinn an Komfort wird von diesen Systemen auch ein Beitrag zur Erhöhung der Verkehrssicherheit erwartet. Dieses Verkehrssicherheitspotenzial wird man jedoch nur ausschöpfen können, wenn die automatisierten Lenksysteme entsprechend gestaltet sind. Insbesondere sollten mögliche Risiken auf Grund automatischen Lenkens minimiert sein. Aus diesen Gründen laufen derzeit Arbeiten auf UNECE-Ebene, die Regelung Nr. 79 über einheitliche Bedingungen für die Genehmigung der Fahrzeuge hinsichtlich der Lenkanlage in Bezug auf automatische Lenkfunktionen (ACSF = Automatically Commanded Steering Functions) zu überarbeiten, um diese unter bestimmten Bedingungen auch bei höheren Geschwindigkeiten genehmigen zu können. Der vorliegende Beitrag reflektiert diese Arbeiten und stellt die Entwicklung der technischen Anforderungen an automatisches Lenken und der für die fahrzeugtechnischen Vorschriften vorgesehenen Testprozeduren dar.
Sicherheitsgurte sind als wirksamer Schutz für Pkw-Insassen bei Verkehrsunfällen weltweit anerkannt; trotzdem werden sie in der Bundesrepublik Deutschland von den Autofahrern noch nicht im wünschenswerten Maße benutzt, obwohl Sicherheitsgurte in ihren Fahrzeugen eingebaut sind. Von dieser Situation ausgehend behandelt die vorliegende Studie sowohl die wirtschaftlichen, rechtlichen und technischen Aspekte, einschließlich alternativer Rückhaltesysteme, als auch die Frage nach der Wirksamkeit des Sicherheitsgurtes. Die Auswertung der internationalen Literatur und die Erörterung der anstehenden Probleme mit Experten führten zu folgenden Feststellungen: - Der Dreipunktgurt kann sowohl hinsichtlich seines Bedienungs- und Tragekomforts als auch im Hinblick auf die beabsichtigte Schutzwirkung im Detail verbessert werden. - Derzeit gibt es keine serienreifen Alternativen zum Gurtsystem. - Das Risiko von gurtbedingten Verletzungsverschlimmerungen ist gering, so dass ihm keine ausschlaggebende Bedeutung beigemessen werden kann. - Ausländische Erfahrungen zeigen, dass durch die Einführung eines Bußgeldes die Kraftfahrer in ihrer überwiegenden Mehrheit die Anlegepflicht befolgen. - Würden in der Bundesrepublik Deutschland alle Frontinsassen von Pkw den Gurt stets anlegen, so könnte der derzeitige Sicherheitsgewinn praktisch verdoppelt werden.
Assessment of the effectiveness of Intersection Assistance Systems at urban and rural accident sites
(2015)
An Intersection Collision Avoidance System is a promising safety system for accident avoidance or injury mitigation at junctions. However, there is still a lack of evidence of the effectiveness, due to the missing real accident data concerning Advanced Driver Assistance Systems. The objective of this study is the assessment of the effectiveness of an Intersection Collision Avoidance System based on real accidents. The method used is called virtual pre-crash simulation. Accidents at junctions were reconstructed by using the numerical simulation software PC-Crashâ„¢. This first simulation is called the baseline simulation. In a second step the vehicles of these accidents were equipped with an Intersection Collision Avoidance System and simulated again. The second simulation is called the system simulation. In the system simulation two different sensors and four different intervention strategies were used, based on a time-to-collision approach. The effectiveness of Intersection Collision Avoidance System has been evaluated by using an assessment function. On average 9% of the reviewed junction accidents could have been avoided within the system simulations. The other simulation results clearly showed a change in the principal direction of force, delta-v and reduction of the injury severity.
The Traffic Accident Research Institute at University of Technology Dresden investigates about 1,000 accidents annually in the area around and in Dresden. These datasets have been summarized and evaluated in the GIDAS (German Accident In-Depth Study) project for 13 years. During the project it became apparent that the specific traffic situation of a covert exit of a passenger car and an intersecting two-wheeler involves a high risk potential. This critical situation develops in a large part due to the lack of visibility between the driver and the intersecting bike. In this paper the accident avoidance potential of front camera systems with lateral field of view, which allows the driver to have an indirect sight into the crossing street area will be presented.
Das Ziel der Untersuchung war, die Grenzen der Belastbarkeit eines Rollstuhl- und Personenrückhaltesystems mit Kraftknoten nach DIN 75078-2 zu ermitteln. Dazu wurden dynamische Schlittenversuche durchgeführt, bei denen die Verzögerungspulse sowie das Gesamtgewicht von Rollstuhl und Prüfpuppe variiert wurden. Für die Untersuchungen kamen ein Prüfrollstuhl, definiert nach ISO 10542, und Rückhaltesysteme mit Kraftknoten gemäß DIN 75078-2 zum Einsatz. Das Rückhaltesystem bestand aus einem Rollstuhl- und einem Personenrückhaltesystem, wobei das Rollstuhlrückhaltesystem (RRS) mit vier bzw. sechs Gurten und entsprechenden Retraktoren an einem dynamischen Schlittenaufbau befestigt wurde. Das Personenrückhaltesystem (PRS) bestand aus einem am Rollstuhl integrierten Beckengurt sowie einem Schulterschräggurt, der am Beckengurt und am Schlittenaufbau befestigt wurde. Ferner wurden bei den Versuchen Prüfpuppen verschiedener Alters- und Gewichtsklassen (P6, HIII 5 %, HIII 50 % und HIII 95 %) eingesetzt Die Belastungsanforderungen für das Rückhaltesystem wurden sukzessiv erweitert, indem einerseits das Gesamtgewicht (Rollstuhl und Prüfpuppe) und andererseits auch die Verzögerungspulse bis zur Versagensgrenze erhöht wurden. Das Vier-Gurt-Rückhaltesystem konnte bei einem Verzögerungspuls von 10 g einem Gesamtgewicht von bis zu 221 kg standhalten. Bei einem Verzögerungspuls von 20 g und einem Gesamtgewicht von 134 kg wurde das Vier-Gurt-System bis über die Grenzen belastet. Das Sechs-Gurt-Rückhaltesystem hat Belastungen bis 221 kg standgehalten. Infolgedessen ist bei einer Erhöhung der Verzögerungspulse auf 20 g und einem Gesamtgewicht von mehr als 109 kg ein Sechs-Gurt-System zu empfehlen.
The project UR:BAN "Cognitive assistance (KA)" aims at developing future assistance systems providing improved performance in complex city traffic. New state-of-the-art panoramic sensor technologies now allow comprehensive monitoring and evaluation of the vehicle environment. In order to improve protection of vulnerable road users such as pedestrians and cyclists, a particular objective of UR:BAN is the evaluation and prediction of their behaviour and actions. The objective of subproject "WER" is development support by providing quantitative estimates of traffic collisions at the very start and predict potential in terms of optimized accident avoidance and reduction of injury severity. For this purpose an integrated computer simulation toolkit is being devised based on real world accidents (GIDAS as well as video documented accidents), allowing the prediction of potential effectiveness and future benefit of assistance systems in this accident scenario. Subsequently, this toolkit may be used for optimizing the design of implemented assistance systems for improved effectiveness.
The evaluation of the expected benefit of active safety systems or even ideas of future systems is challenging because this has to be done prospectively. Beside acceptance, the predicted real-world benefit of active safety systems is one of the most important and interesting measures. Therefore, appropriate methods should be used that meet the requirements concerning representativeness, robustness and accuracy. The paper presents the development of a methodology for the assessment of current and future vehicle safety systems. The variety of systems requires several tools and methods and thus, a common tool box was created. This toolbox consists of different levels, regarding different aspects like data sources, scenarios, representativeness, measures like pre-crash-simulations, automated crash computation, single-case-analyses or driving simulator studies. Finally, the benefit of the system(s) is calculated, e.g. by using injury risk functions; giving the number of avoided/mitigated accidents, the reduction of injured or killed persons or the decrease of economic costs.
Accident research 2.0: New methods for representative evaluation of integral safety in traffic
(2013)
BMW has developed a procedure for rating Advanced Driver Assistance Systems (ADAS) benefits that integrates two distinct tools. The tool "S.A.F.E.R." is designed to analyze the pre-crash phase. The aim of S.A.F.E.R. is to simulate all relevant processes in sufficient detail to obtain reproducible estimates of key indicators (effectiveness, false positives, etc.). The relevant processes include not only traffic and vehicle dynamics, but also environmental and most importantly human factors. Representative distributions of factors and parameters are obtained by taking the stochastic variation of all relevant parameters into account in the simulations. The second tool, known as "ICOS", has been designed to provide a high-resolution, high-fidelity description of crash phase dynamics. If one converts the outputs of stochastic simulation into inputs for crash dynamics, the result is a comprehensive description of exactly how a safety system can reduce injuries. Applications currently focus on high-fidelity simulation of individual crashes in order to enhance our understanding and optimization of connected safety systems. An integrated simulation process thus allows an exact prediction of the effectiveness in individual cases in terms of injury severity. The development and rating of integral safety need to reflect the true efficiency in the field. The integrated approach described here could provide a valid and reproducible basis for rating connected systems of active and passive safety. In particular, "virtual experiments" using a traffic-based approach and incorporating models of all relevant processes constitute an essential element of the approach.