91 Fahrzeugkonstruktion
Supported by field accident data and monitoring results of European Regulation (EC) No. 78/2009, recent plans of the European Commission regarding a way forward to improve passive safety of vulnerable road users include, amongst other things, an extension of the head test area. The inclusion of passive cyclist safety is also being considered by Euro NCAP. Although passenger car to cyclist collisions are often severe and have a significant share within the accident statistics, cyclists are neither considered sufficiently in the legislative nor in the consumer ratings tests. Therefore, a test procedure to assess the protection potential of vehicle fronts in a collision with cyclists has been developed within a current research project. For this purpose, the existing pedestrian head impact test procedures were modified in order to include boundary conditions relevant for cyclists as the second big group of vulnerable road users. Based on an in-depth analysis of passenger car to cyclist accidents in Germany the three most representative accident constellations have been initially defined. The development of the test procedure itself was based on corresponding simulations with representative vehicle and bicycle models. In addition to different cyclist heights, reaching from a 6-year-old child to a 95%-male, also four pedal positions were considered. By reconstruction of a real accident the defined simulation parameters could be validated in advance. The conducted accident kinematics analysis shows for a large portion of the constellations an increased head impact area, which can reach beyond the roof leading edge, as well as high average values for head impact velocity and angle. Based on the simulation data obtained for the different vehicle models, cyclist-specific test parameters for impactor tests have been derived, which have been further examined in the course of head and leg impact tests. In order to study the cyclist accident kinematics under real test conditions, different full scale tests with a Polar-II dummy positioned on a bicycle have been conducted. Overall, the tests showed a good correlation with the simulations and support the defined boundary test conditions. Typical accident scenarios and simulations reveal higher head impact locations, angles and velocities. An extended head impact area with modified test parameters will contribute to an improved protection of vulnerable road users including cyclists. However, due to significantly differing impact kinematics and postures between the lower extremities of pedestrians and cyclists, these injuries cannot be addressed by the means of current test tools such as the flexible pedestrian legform impactor FlexPLI. Based on the findings obtained within the project as well as the existing pedestrian protection requirements a cyclist protection test procedure for use in legislation and consumer test programmes has been developed, whose requirements have been transferred into a corresponding test specification. This specification provides common head test boundary conditions for pedestrians and cyclists, whereby the existing requirements are modified and two parallel test procedures are avoided.
Die Verordnungsgeber haben länderübergreifende Normen und Vorschriften für die Durchführung und Auswertung von Crashversuchen mit Personenkraftwagen bei verschiedenen Aufprallarten entwickelt, die im Rahmen der Entwicklung und Zulassung neuer Fahrzeuge Anwendung finden. Verbraucherschutzorganisationen, Automobilclubs und Fachzeitschriften tragen mit der Durchführung und Publikation eigener Tests dazu bei, dass die passive Sicherheit von Personenkraftwagen in der breiten Öffentlichkeit mehr und mehr beachtet wird. Im Gegensatz dazu ist die Durchführung von Crashtests zur Untersuchung und Bewertung der passiven Sicherheit von Motorrädern relativ neu. Vor diesem Hintergrund hat die Bundesanstalt für Straßenwesen das vorliegende Forschungsprojekt vergeben. Hierbei waren unter Verwendung geeignet erscheinender Prüfverfahren reale Unfallsituationen nachzubilden. Unter Beachtung der Vielfalt der motorisierten Zweiräder mit ihrer Einteilung in verschiedene Zulassungs-Kategorien und zugehöriger Unfalldaten wurde das reale Unfallgeschehen analysiert. Neben Daten aus der amtlichen Unfallstatistik wurden dabei Informationen aus der Literatur und eigene Erhebungen ausgewertet. Ergänzend ist der aktuelle Kenntnisstand zur Biomechanik aufbereitet worden. Eine Beschreibung des Status quo der passiven Motorradsicherheit erfolgte unter Analyse der hierbei relevanten Elemente, Baugruppen und Eigenschaften des Motorrades. Dazu gehören Lenker, Sitzbank, Fußrasten, Tank, Verkleidung, Airbag (noch nicht im Hersteller-Angebot), Vorderradgabel und Standrohre sowie die Aufsassen-Kopfhöhe. Weiterhin gingen die Ergebnisse von Full-Scale-Crashtests, die im internationalen Standard ISO 13232 beschrieben sind, mit Anstößen von Motorrädern an der Seite von Personenkraftwagen in die Darstellung des Status quo der passiven Motorradsicherheit ein. Zusätzlich wurden im Rahmen des Forschungsprojektes Schlittenversuche durchgeführt. Ein zur Darstellung des rechtwinkligen Motorradanpralles an der Seite eines stehenden Personenkraftwagens geeigneter Schlitten ist im Rahmen des Projektes entworfen, realisiert und eingesetzt worden. In der Literatur beschriebene Motorrad-Sicherheitskonzepte und Vorschläge für besondere Motorrad-Sicherheitselemente sind ebenfalls dargestellt worden. Im Rahmen des Forschungsprojektes wurde ein umfassender Ansatz verfolgt. Er enthält die Bewertung von Sicherheitsmerkmalen, die aus technischen Beschreibungen entnommen und am stehenden Fahrzeug ermittelt werden können (Primärdaten) sowie die Ergebnisse von dynamischen Crash- und Schlittentests (Sekundärdaten). Dabei erfolgt stets die Orientierung am realen Unfallgeschehen (Tertiärdaten). Der internationale Standard ISO 13232 wird als geeigneter Ausgangspunkt eines umfassenden Prüf- und Bewertungsverfahrens für die passive Sicherheit motorisierter Zweiräder erkannt. Zur Erweiterung der bereits definierten Testverfahren werden Schlittentests vorgeschlagen. Außerdem werden Alleinunfälle des Motorrades zu beachten sein. Die Ergebnisse des Forschungsprojektes tragen dazu bei, die Aspekte der passiven Sicherheit von motorisierten Zweirädern zu objektivieren.
Für eine Reihe von EU Regelungen im Bereich Fahrzeugsicherheit erlaubt eine Verordnung bereits seit dem Jahr 2010 virtuelles Testen für die Typzulassungsprüfung. Technische Details bzw. konkrete Prozeduren für spezifische Regelungen sind in dieser Verordnung jedoch nicht enthalten. Das Hauptziel des europäischen Projekts IMVITER (lmplementation of Virtual Testing in Safety Regulations) war es, basierend auf der neuen Verordnung ein virtuelles Testverfahren auszuarbeiten und dabei offene Fragen zu berücksichtigen. Um die im Projekt-Konsortium unter Berücksichtigung der Anliegen aller Interessensgruppen wie Autohersteller, Zulassungsbehörden und technischer Dienste erarbeiteten offenen Punkte zu adressieren, wurde ein generisches Flussdiagramm entwickelt, das den Ablauf einer virtuell basierten Typprüfung darstellt. ln diesem Diagramm ist der virtuelle Typgenehmigungsprozess in drei aufeinander folgende Phasen aufgeteilt, die Verifikations-, Validierungs- und Typgenehmigungsphase. Von entscheidender Bedeutung ist die Phase der Validierung des Simulationsmodells, für die im IMVITER-Projekt eine Methodik vorgeschlagen wurde. Mit der im Projekt vorgeschlagenen Validierungsmethode ist kein Austausch des Simulationsmodells zwischen Fahrzeughersteller und technischem Dienst notwendig, so dass die Vertraulichkeit von Betriebsgeheimnissen nicht gefährdet ist. Zur Validierung des Modells werden jedoch immer Versuche notwendig sein. Dies gilt sowohl für die Überpruefung von passiven als auch aktiven Fahrzeugsicherheitssystemen. Eine zusammenfassende Betrachtung der Erfahrungen aus dem IMVITER-Projekt ergab, dass mit der Einführung von virtuellem Testen keine Erhöhung der Anforderungen an die Fahrzeugsicherheit bzgl. bestehender Regelungen verbunden sein sollte. Jedoch werden auch weiterhin neue zusäztliche Regelungen erforderlich sein, da sich das Unfallgeschehen und die Fahrzeugtechnologie weiterentwickeln und ändern werden. Diese sollten von Beginn an die Möglichkeiten des virtuellen Testens nutzen, insbesondere bei Testverfahren für neue Technologien, z.B. aktiver Fahrzeugsicherheitssysteme. Hier bieten virtuelle Testverfahren nicht nur eine Kosten- oder Zeitersparnis, sondern ermöglichen teilweise erst die sinnvolle Abprüfung von neuen Sicherheitssystemen, die mit aktuellen auf Hardware-Test basierenden Verfahren überhaupt nicht möglich wären.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
PROSPECT (Proactive Safety for Pedestrians and Cyclists) is a collaborative research project involving most of the relevant partners from the automotive industry (including important active safety vehicle manufacturers and tier-1 suppliers) as well as academia and independent test labs, funded by the European Commission in the Horizon 2020 research program. PROSPECT's primary goal is the development of novel active safety functions, to be finally demonstrated to the public in three prototype vehicles. A sound benefit assessment of the prototype vehicle's functionality requires a broad testing methodology which goes beyond what has currently been used. Since PROSPECT functions are developed to prevent accidents in intersections, a key aspect of the test methodology is the reproduction of natural driving styles on the test track with driving robots. For this task, data from a real driving study with subjects in a suburb of Munich, Germany was used. Further data from Barcelona will be available soon. The data suggests that intersection crossing can be broken down into five phases, two phases with straight deceleration / acceleration, one phase with constant radius and speed turning, and two phases where the bend is imitated or ended. In these latter phases, drivers mostly combine lateral and longitudinal accelerations and drive what is called a clothoid, a curve with curvature proportional to distance travelled, in order to change lateral acceleration smoothly rather than abrupt. The data suggests that the main parameter of the clothoid, the ratio distance travelled to curvature, is mostly constant during the intersections. This parameter together with decelerations and speeds allows the generation of synthetic robot program files for a reproduction of natural driving styles using robots, allowing a much greater reproducibility than what is possible with human test drivers. First tests show that in principle it is possible to use the driving robots for vehicle control in that manner; a challenge currently is the control performance of the robot system in terms of speed control, but it is anticipated that this problem will be solved soon. Further elements of the PROSPECT test methodology are a standard intersection marking to be implemented on the test track which allows the efficient testing of all PROSPECT test cases, standard mobile and light obstruction elements for quick reproduction of obstructions of view, and a concept for tests in realistic surroundings. First tests using the PROSPECT test methodology will be conducted over the summer 2017, and final tests of the prototype vehicles developed within PROSPECT will be conducted in early 2018
Im Jahresbericht 2007/2008 wird das 25-jährige Standortjubiläum der Bundesanstalt für Straßenwesen in Bergisch Gladbach-Bensberg zum Anlass genommen, auf die Arbeitsergebnisse der vergangenen Jahre zurückzublicken und den Blick in die Zukunft zu richten. Ausgewählte Beiträge aus allen Fachdisziplinen der BASt zeigen, welche Themen von den Mitarbeiterinnen und Mitarbeitern der BASt in den letzten Jahren bearbeitet wurden, wo die Schwerpunkte heute liegen und wie die Aufgaben der Zukunft aussehen.rnAußerdem wird ein kurzer Rückblick auf den Bau der Dienstgebäude in Bensberg und die Entwicklung der BASt in den letzten 25 Jahre gegeben sowie über den Tag der offenen Tür berichtet, an dem das Standortjubiläum in Bensberg zusammen mit etwa 4.000 Gästen gefeiert wurde.rnDie letzten Jahre waren altersbedingt geprägt von vielen personellen Wechseln " auch in der Leitungsebene. Der Generationswechsel ist damit in der BASt nahezu abgeschlossen. Das Kapitel "Mitarbeiterinnen und Mitarbeiter" informiert über die personellen Entwicklungen und Auszeichnungen der Beschäftigten sowie über den Wechsel des Präsidenten im Jahr 2008.rnAbgerundet wird der Jahresbericht mit den Aktivitäten der Öffentlichkeitsarbeit, der Internationalen Zusammenarbeit, einer Zusammenstellung der Publikationen der Jahre 2007 und 2008 sowie Datenbanken und -sammlungen. rn
Jahresbericht 2006
(2007)
Der Jahresbericht der Bundesanstalt für Straßenwesen gibt einen Überblick über die Arbeitsschwerpunkte der BASt im Jahr 2006. Neben grundlegenden Informationen über die BASt werden 31 Projekte aus den fünf Forschungsabteilungen der BASt vorgestellt. Abgerundet wird der Jahresbericht mit den Aktivitäten der Öffentlichkeitsarbeit, der Internationalen Zusammenarbeit, einer Zusammenstellung der zum Teil in der BASt entwickelten und gepflegten Datenbanken und -sammlungen sowie Zahlen und Fakten des Jahres 2006.
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.