83 Unfall und Mensch
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (87) (entfernen)
Schlagworte
- Conference (56)
- Konferenz (56)
- Germany (39)
- Deutschland (38)
- Accident (36)
- Unfall (36)
- Injury (20)
- Safety (19)
- Sicherheit (19)
- Verletzung (19)
The BASt-project group "Legal consequences of an increase in vehicle automation" has identified, defined and consequently compiled different automation degrees beyond Driver Assistance Systems. These are partial-, high- and full automation. According to German regulatory law, i.e. the German Road Traffic Code, it has been identified that the distinctive feature of different degrees of automation is the permanent attention of the driver to the task of driving as well as the constant availability of control over the vehicle. Partial automation meets these requirements. The absence of the driver- concentration to the traffic situation and to execute control is in conflict with the use of higher degrees of vehicle automation (i.e. high and full automation). Their use is therefore presently not compatible with German law, as the human driver would violate his obligations stipulated in the Road Traffic Code when fully relying on the degree of automation these systems would offer. As far as higher degrees of automation imply free-hand driving, further research in terms of behavioural psychology is required to determine whether this hinders the driver in the execution of permanent caution as required by sec. 1 para. 1 StVO (German Road Traffic Code). As far as liabilities according to the StVG (German Road Traffic Act) are concerned, the presently reversed burden of proof on the driver within sec. 18 para. 1 S. 2 StVG might no longer be considered adequate in case of higher degrees of automation that allow the driver to draw attention from the task of driving (in case making such use of a system would be permitted by the German Road Traffic Code). The liability of the vehicle "keeper", according to the German Road Traffic Act, would remain applicable to all defined degrees of automation. In case of partial automation, the use of systems according to their limits is accentuated. The range of use that remains within the intended must be defined closely and unmistakeably. Affecting user expectations properly can immensely help to maintain safe use, in case design-measures that exclude overreliance are not available according to the current state of the art (otherwise such measures would have to be applied primarily). In case of the higher degrees of automation that no longer require the driver- permanent attention (under the presupposition their use would be permitted by the German Road Traffic Code), every accident potentially bears the risk to cause product liability on the side of the manufacturer. Liability of the manufacturer might only be excluded in case of a breach of traffic rules by a third party or in case of overriding/ oversteering by the driver. In so far aspects of German procedural law and the burden of proof are of great importance. The project group has identified the need for further continuative research not only to advance legal assessment but also to improve basic technical conditions for vehicle automation as well as product reliability.
Many safety-relevant tasks in control or diagnostics require binary choices such as "conflict versus separation" in air traffic control, "normal versus pathological" when interpreting x-ray pictures, or "permitted versus forbidden" when inspecting airport security scans. Deciders often are uncertain, but nevertheless required to decide between two alternatives, that is, they have not only to decide upon an action, but also about the admissible level of uncertainty. If the accepted level of judgment certainty is not taken into account, the sequence of decisions does not capture the full picture of the underlying decision process. Differences in judgment certainty are relevant, because they reflect not only the adequacy of the human-machine interface that is evaluated, but also the differences in expertise of the decider and the requirements of the actual situation or task. Therefore, capturing both judgment certainty and discrimination performance is essential. A comparison of different human-machine-interfaces (for air traffic control) is used to illustrate a methodological approach, which allows for integrated analyses of decision processes based on receiver-operator-characteristics and practical guidelines for the evaluation of human-machine-interfaces for safety-relevant operation procedures are provided.
Do learner gain sufficient braking capabilities at the end of education for collision avoidance?
(2013)
The paper describes a test design to evaluate the braking behaviour in the course of the driver education. The results show that the braking capabilities increased during the driver education and the learning effects are the same for males and females. The evaluation limit is set to 6 m/s-². At the beginning of education, 50% of the drivers do not reach this limit, although the driver education car is equipped with an emergency brake assist, which is regularly installed in all vehicles since 2009. After the education, 100% of the drivers can reach the limit. The results are mapped to a collision avoidance scenario.
In 2011 399 cyclists died in road accidents in Germany and another 76.351 cyclists have been injured. Since 2000 the number of injured or fatally injured cyclists remained on the same high level. Cyclists form 19% of all casualties in German road traffic, although the modal split rate of this transport mode in 2008 was only 10% of trips and resp. 3% of kilometres per day. The high proportion of fatally and seriously injured shows the high vulnerability of cyclists. The demographic shift towards an older population in Germany and the governmental recommendation of increased bicycle use as an ecological, economical and healthy alternative to other modes of transport lead to the assumption that bicycle use especially of elderly people will increase. Based on these facts about the German cyclists' situation a representative survey of 2.000 cyclists was conducted. Results display use patterns and accident involvement on a descriptive level. Overall 7.7% of cyclists report to have been involved in at least one road traffic accident within the last three years. The performed path model analysis reveals an acceptable model fit. Though the explained variance of accident involvement of the applied psychological factors was low, significant relations between several of these factors and especially risky behaviour could be found.
Since 2005, the motorcycle crash fatalities in the US exceeded 10% of the overall annual traffic fatalities. Consequently, it has become critical to gain in-depth understanding of the factors and characteristics contributing to motorcycle crashes. Unfortunately, there currently exists no database gathering the necessary information for an in-depth analysis of the US motorcycle crashes. So this study utilizes the NASS/CDS database (National Automotive Sampling System, Crashworthiness Data System) in order to gain insights into the patterns and factors leading to a NASS/CDS motorcycle crash, from 1997 to 2007. NASS/CDS samples about 5,000 passenger car tow-away crashes per year. Each case includes photographs and detailed data on crash and pre-crash characteristics, vehicle types, trajectories, types of impact, and other pertinent roadway and crash scene information, allowing an in-depth investigation of the crash mechanisms. However, the NASS/CDS sampling process specifically focuses on passenger car crashes, so the cases extracted only correspond to crashes in which a passenger vehicle was towed, and a motorcycle was somehow involved. Thus, a by-hand in-depth review of about 200 cases allowed retrieving 106 relevant crashes for this study, tending to represent the severe passenger vehicle(s) versus motorcycle(s) crashes on US roads. The findings lead to the conclusion that these crashes mostly result from the low conspicuity of the motorcycle, and from the inability of the car drivers to fully appreciate and anticipate the behavior of a motorcycle. Indeed, it has been shown that, first, the car drivers involved in these cases did not attempt any avoidance maneuver, second, they were largely of ages under 25, and finally, the majority of the crashes were in an intersection scenario. In addition, the two major scenarios unveiled were the car attempting a left turn from the opposite direction and the car attempting a left turn from the right. The paper mentions several solutions to enhance the motorcycle- conspicuity and to allow the car drivers to better anticipate its behavior, which seem to be key factors in the intersection-related crashes (and more generally in the passenger vehicle(s) versus motorcycle(s) crashes).
The purpose of this study was to analyse the actual injury situation of bicyclists regarding accidents involving more than one bicyclist. Bicyclists were included in a medical and technical analysis to create a basis for preventive measures and discovered repeating accident patterns and circumstances such as daytime, environment, helmet use rate. Technical and medical data were collected at the scene, shortly after accident. The population was compared focusing on bicycle versus bicycle accidents. Technical analysis included speed at crash, type of collision, impact angle, environment, used lane and relative velocity. Medical analysis included injury pattern and severity (AIS, ISS). Included were 578 injured bicyclists in 289 accidents from years 1999 to 2008, 61 percent were male (n=350) and 39 percent female (n=228). Sixty-seven percent ranged between 18 to 64 years of age, twelve percent each between 13 to 17 years of age and older than 65 years, eight percent between 6 to 12 years and one percent between 2 to 5 years.. Crashes took place in urban areas in 92 percent, in rural areas in 8 percent. Weather conditions were dry lanes in 97 percent and wet conditions in 3 percent. Eighty-three percent of all accidents happened during daytime, ten percent during night, and seven percent during dawn. The helmet use rate was only 7,5 percent in all involved bicyclists. The mean Maximum Abbreviated injury scale, Injury severity score was 1,31. Bicyclists are still minimally- or unprotected road users. The helmet use rate is unsatisfactorily low. The incidence of bicycle to bicycle crashes is high. Most of these accidents take place in urban areas. The level and pattern of injuries is moderate. Most of the more severe injuries occur to the head and could have been avoided by frequent helmet use.
The average CO2 concentrations relevant to a motorcyclist wearing an integral helmet were measured twenty years ago and found to be alarmingly high. The present study examined gas concentrations typically inhaled by a motorcyclist. Average concentrations of CO2 for persons (n=4) wearing integral motorcycle helmets were measured in the laboratory and the field to facilitate comparison to previous work, and similarly high average concentrations were found: above 2% when stationary, well below 1% for speeds of 50km/h or more. Detailed measurements of the time-dependent CO2 concentrations during normal inhalation showed levels of about half of the corresponding average concentrations, including 1% at standstill, though higher concentrations (4% or more) are inhaled at the beginning of each breath. Opening the visor at standstill lowered the average inhaled concentration only to about 0.8%. The oxygen deficiency is equal to the CO2 concentration, and could also contribute negatively to motorcyclist cognitive abilities.
Validation of human pedestrian models using laboratory data as well as accident reconstruction
(2007)
Human pedestrian models have been developed and improved continually. This paper shows the latest stage in development and validation of the multibody pedestrian model released with MADYMO. The biofidelity of the multibody pedestrian model has been verified using a range of full pedestrian-vehicle impact tests with a large range in body sizes (16 male, 2 female, standing height 160-192cm, weight 53.5-90kg). The simulation results were objectively correlated to experimental data. Overall, the model predicted the measured response well. In particular the head impact locations were accurately predicted, indicated by global correlation scores over 90%. The correlation score for the bumper forces and accelerations of various body parts was lower (47-64%), which was largely attributed to the limited information available on the vehicle contact characteristics (stiffness, damping, deformation). Also, the effects of the large range in published leg fracture tolerances on the predicted risk to leg fracture by the pedestrian model were evaluated and compared with experimental results. The validated mid-size male model was scaled to a range of body sizes, including children and a female. Typical applications for the pedestrian models are trend studies to evaluate vehicle front ends and accident reconstructions. Results obtained in several studies show that the pedestrian models match pedestrian throw distances and impact locations observed in real accidents. Larger sets of well documented cases can be used to further validate the models especially for specific populations as for instance children. In addition, these cases will be needed to evaluate the injury predictive capability of human models. Ongoing developments include a so-called facet pedestrian model with a more accurate geometry description and a more humanlike spine and neck and a full FE model allowing more detailed injury analysis.
Accidents involving two wheels vehicles represent one of the more important types of accidents in Europe. These accidents are usually not easy to reconstruct specially for the analysis of the injuries and its correlation with accident dynamics and evidences. Different methodologies are applied in this work for the reconstruction of two wheeler accidents, especially accident involving motorcycles. From the typologies of road evidences like skid marks, to the use of Pc-Crash and the use of Madymo models, different reconstruction of real accidents are presented. One of the questions that sometimes arise for legal purposes when some type of head injuries arise is if the occupant was wearing or not a helmet. The correlation of head injuries with the use of the helmet is a very important issue, therefore an important legal aspect. One of the key questions for the reconstructions that is difficult to analyze, is if the vehicle occupant, was or not, wearing the helmet. Based on the previously collected information, a generic model of a helmet was developed on CAD 3D, followed by its conversion into finite elements, all in order to perform impact tests using the Madymo software that would help improve the helmet- safety, but that also can be used as a tool in accident reconstruction.
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
One main objective of the EU-Project SENIORS is to provide improved methods to assess thoracic injury risk to elderly occupants. In contribution to this task paired simulations with a THOR dummy model and human body model will be used to develop improved thoracic injury risk functions. The simulation results can provide data for injury criteria development in chest loading conditions that are underrepresented in PMHS test data sets that currently proposed risk functions are based on. To support this approach a new simplified generic but representative sled test fixture and CAE model for testing and simulation were developed. The parameter definition and evaluation of this sled test fixture and model is presented in this paper. The justification and definition of requirements for this test set-up was based on experience from earlier studies. Simple test fixtures like the gold standard sled fixture are easy to build and also to model in CAE, but provide too severe belt-only loading. On the other hand a vehicle buck including production components like airbag and seat is more representative, but difficult to model and to be replicated at a different laboratory. Furthermore some components might not be available for physical tests at later stage. The basis of the SENIORS generic sled test set-up is the gold standard fixture with a cable seat back and foot rest. No knee restraint was used. The seat pan design was modified including a seat ramp. The three-point belt system had a generic adjustable load limiter. A pre-inflated driver airbag assembly was developed for the test fixture. Results of THOR test and simulations in different configurations will be presented. The configurations include different deceleration pulses. Further parameter variations are related to the restraint system including belt geometry and load limiter levels. Additionally different settings of the generic airbag were evaluated. The test set-up was evaluated and optimized in tests with the THOR-M dummy in different test configurations. Belt restraint parameters like D-ring position and load limiter setting were modified to provide moderate chest loading to the occupant. This resulted in dummy readings more representative of the loading in a contemporary vehicle than most available PMHS sled tests reported in the literature. However, to achieve a loading configuration that exposes the occupant to even less severe loading comparable to modern vehicle restraints it might be necessary to further modify the test set-up. The new generic sled test set-up and a corresponding CAE model were developed and applied in tests and simulations with THOR. Within the SENIORS project with this test set-up also volunteer and PMHS as well as HBM simulations are performed, which will be reported in other publications. The test environment can contribute in future studies to the assessment of existing and new frontal impact dummies as well as dummy improvements and related instrumentation. The test set-up and model could also serve as a new standard test environment for PMHS and volunteer tests as well as HBM simulations.
The main focus of the benefit estimation of advanced safety systems with a warning interface by simulation is on the driver. The driver is the only link between the algorithm of the safety system and the vehicle, which makes the setup of a driver model for such simulations very important. This paper describes an approach for the use of a statistical driver model in simulation. It also gives an outlook on further work on this topic. The build-up process of the model suffices with a distribution of reaction times and a distribution of reaction intensities. Both were combined in different scenarios for every driver. Each scenario has then a specific probability to occur. To use the statistical driver model, every accident scene has to be simulated with each driver scenario (combinations of reaction times and intensities). The results of the simulations are then combined regarding the probabilities to occur, which leads to an overall estimated benefit of the specific system. The model works with one or more equipped participants and delivers a range for the benefit of advanced safety systems with warning interfaces.
This paper set out to examine the possibilities for injury avoidance implications for older drivers in crashes, based on crash and injury patterns among older drivers and current trends in ageing in most western societies. A number of safety technologies were identified and discussed which have potential for improving vehicle older driver crash avoidance and crashworthiness. While there were some promising estimates available of the likely benefits of this technology for improving safety, it is evident that they need to be confirmed for older drivers, given their age-related disabilities and sensory limitations. Further research is urgently required to ensure that these technologies yield safety benefits without any disbenefits for older drivers.rn
The Swedish National Road Administration (SNRA), the Japanese Automobile Research Institute (JARI) and the Federal Highway Research Institute (BASt) are co-operating in the International Harmonized Research Activities on Intelligent Transportation Systems (IHRA-ITS). Under this umbrella a joint study was conducted. The overall objective of this study was to contribute to the definition and validation of a "battery of tools" which enables a prediction and an assessment of changes in driver workload due to the use of in-vehicle information systems (IVIS) while driving. In this sense \"validation\" means to produce empirical evidence from which it can be concluded that these methods reliably discriminate between IVIS which differ in terms of relevant features of the HMI-design. Additionally these methods should also be sensitive to the task demands imposed on the driver by the traffic situation and their interactions with HMI-design. To achieve these goals experimental validation studies (on-road and in the simulator) were performed in Sweden, Germany and Japan. As a common element these studies focused on the secondary task methodology as an approach to the study of driver workload. In a joint German-Swedish on-road study the Peripheral Detection Task (PDT) was assessed with respect to its sensitivity to the complexity of traffic situations and effects of different types of navigation systems. Results show that the PDT performance of both the German and the Swedish subjects reflects the task demands of the traffic situations better than those of the IVIS. However, alternative explanations are possible which will be examined by further analyses. Results of this study are supplemented by the Japanese study where informational demands induced by various traffic situations were analysed by using a simple arithmetic task as a secondary task. Results of this study show that relatively large task demands can be expected even from simple traffic situations.
This article describes the development of techniques to minimize automobile driver distraction when an in-vehicle information systems (IVIS) that requires visual attention is in use. The authors explain the visual occlusion technique that has been developed as a tool for the assessment of the in-vehicle human-machine interface (HMI) of IVIS in terms of visual demands. The authors addressed an unresolved issue in previous standardized experimental protocols - how subjects make use of the occluded intervals and how this might affect the assessments of visual demands. This study protocol assumed that subjects would continue task performance during occluded periods, leading to an underestimation of visual demands by the occlusion parameters "total shutter open time" (TSOT) and the "occlusion index". The authors predicted that a simple additional loading task to be performed in parallel could disrupt IVIS task performance during the occluded period leading to higher estimations of visual demands by TSOT and R. Their prediction was confirmed by the study findings. The results also showed that under the condition of additional auditory tracking, TSOT and R discriminated more clearly between an "easy" and a "difficult" IVIS task than under the standard condition. They conclude with a discussion of the implications of this research for designers of assessment tools for driver visual distractions.
Learner drivers are readied for their participation in motorised transport within the framework of specific, internationally-diverse preparation systems. These systems are historically developed and are characterised by country-specific economic, infrastructural, legal and cultural circumstances. With the aid of functionally-distinguishable teaching and learning methods as well as testing methods, a conceptual framework was created whilst drawing upon research-methodological approaches of comparative political science as well as teaching and learning principles that facilitated a description and analysis of the systems for a comparative observation to be performed. The systems for the preparation of learner drivers in 44 countries are illustrated in the report. The descriptions are based upon surveys of experts from various institutions (ministries of transport, driving instructor associations, testing organisations) as well as upon literary and Internet research. Alongside European countries with a traditional formal driver training, \"Graduated Driver Licensing\" systems that are primarily encountered in English-speaking countries were also taken into account when selecting the countries. They are characterised by the guarantee of gaining comprehensive driving experience under reduced risk conditions in the form of supervised driving prior to the start of independent driving as well as protective special rules for learner drivers whilst gaining further driving experience during the initial phase of independent driving. The results enable a detailed insight into the country-specific structure of learner driver preparation with the components of the formal driver training in driving schools, informal teaching and learning methods such as supervised driving, the driving tests that must be successfully completed as well as legal frameworks and quality assurance measures. The functionality of system components and architectures shall be discussed against the backdrop of evaluation findings regarding the effectiveness in terms of safety.
The Swedish "Vision Zero" regards road fatalities and severe injuries as unacceptable. The vision is based on this ethical perspective together with a fundament of shared responsibility between the system designers and the road user. The design of the traffic system shall protect the road user from these effects as long as he or she follows the traffic rules. It should be possible to make a mistake without being killed. This policy has, during the first period of the "vision zero" (since 1997) put high priority on road and car design where the purpose has been to develop a forgiving environment. Gradually it has, however, become clear that much more effort has to be focused on the responsibility of the road user. Protecting measures will have limited effect as long as the understanding and acceptance from road users is limited. During the last years, Sweden has gone through several improvements of the driver education and is in the middle of important improvements of road safety education for children in schools. Several EU-projects has contributed to this development. One aspect that has received large international interest is the lay instructed driver training from 16 years of age supervised by parents. This has been in use since 1993. Another is the development of mandatory courses, such as an introduction for the learner and the lay instructor, a "risk awareness" courses dealing specifically with speeding, seat belt use, drunk driving, tiredness, and driving on low friction. The presentation will share some of the "vision zero" fundaments together with the latest experiences, research and development concerning driver education in Sweden.
The European CASPER (Child Advanced Safety Project for European Roads) project studying car child safety includes a sociological approach in order to have a better understanding of the behaviour of parents driving children under 12 years old. A questionnaire was distributed via the internet in Europe with 998 parents (representing 1638 children) from 22 European countries responding. The results inform on the way parents secure their children during a car trip. Many parents did not control how their children were installed in the child restraint system (CRS). A toddler was more likely to travel into a child seat than an older child was. Regarding misuse situations, an important part of the participants did not think that they could make mistakes when fixing the child seat to the car (26%) or when placing the child into the seat (39%). This leaves an important field of action especially by communication via different media and in the CRS sale outlets.
Cycling supports the independence and health of the aging population. However, elderly cyclists have an increased injury risk. The majority of injured cyclists is victim of a single-sided accident, an accident in which there is no other party involved. The aim of the project "Safe and Aware on the bicycle" is to develop guidelines for an advisory system that is useful in preventing single-sided accidents. This system is able to support the elderly cyclist; enabling the cyclist to timely adapt his cycling behaviour and improve cycling safety and comfort. For the development of such advisory system the causes of singles accidents and the wishes of the elderly cyclist must be known. First step to obtain this insight was a literature survey and an GIDAS research. Unfortunately accidentology research with GIDAS did not give the full understanding of the pre-crash situations and (especially the behaviour related) factors leading to the accident. The second step was consultation of elderly cyclist through a questionnaire (n=800), in-depth interviews (n=12) and focus group sessions (n=15). This offered complementary information and a much better understanding of the behavioural aspects. Results concern the behaviour in traffic and identify specific physical (i.e. problems looking backwards over the shoulder) and mental issues. Furthermore, the needs and wishes for support in specific cycling situations were identified. In conclusion; The GIDAS results together with the information obtained contacting the elderly cyclists enabled setting up requirements for an advisory system, which is useful in preventing single-sided accidents.
Accident simulation and reconstruction for enhancing pedestrian safety: issues and challenges
(2015)
The enhancement of pedestrian safety represents a major challenge in traffic accidents. This study allows a better understanding of the issues in pedestrian protection. It highlights the potential of in-depth studies in identifying relevant crash parameters interfering in the pedestrian safety. A computational simulation tool was developed to reconstruct pedestrian real-world crashes. A sample of 100 in-depth accident cases was reconstructed from two sources: 40 crashes provided by IFSTTAR-LMA and 60 crashes from CASR. To exemplify the methodology, two accident cases from each database were illustrated. A description of the sample of crashes was presented including the travel and impact speed of the vehicle, the driver reaction, the pedestrian walking speed, the scene configuration with the eventual obstacles, etc. This detailed description is pointing to the major factors affecting the limits of pedestrian safety systems.
The changed focus in vehicle safety technology from secondary to primary safety systems need to evolve new methods to investigate accidents, high critical, critical and normal driving situations. Current Naturalistic Driving Studies mostly use vehicles that are highly equipped with additional measuring devices, video cameras, recording technology, and sensors. These equipped fleets are very expensive regarding the setup and administration of the study. Due to the great rarity of crashes it is additionally necessary to have a high distribution and a homogeneous distribution of subject groups. At the end all these facts are leading to a very expensive study with a manageable number of data. Smartphones are becoming more and more popular not only for younger people. Contrary to traditional mobile phones they are mostly equipped with sensors for acceleration and yaw rates, GPS modules as well as cameras in high definition resolution. Additionally they have high-performance processors that enable the execution of CPU-intensive tools directly on the phone. The wide distribution of these smartphones enables researchers to get high numbers of users for such studies. The paper shows and demonstrates a software app for smartphones that is able to record different driving situations up to crashes. Therefore all relevant parameter from the sensors, camera and GPS device are saved for a given duration if the event was triggered. The complete configuration is independently adjustable to the relevant driver and all events were sent automatically to the research institute for a further process. Direct after the event, interviews with the driver can be done and important data regarding the event itself are documented. The presentation shows the methodology and gives a demonstration of the working progress as well as first results and examples of the current study. In the discussion the advantages of this method will be discussed and compared with the disadvantages. The paper shows an alternative method to investigate real accident and incident data. This method is thereby highly cost efficient and comparable with existing methods for benefit estimation.
This study analyses no.39 cases in which n.41 motorcyclists were fatally injured, or 36% of total motorcycle fatalities in Northern Ireland between 2004 and 2010 (n.114). There were n.17 cases (43.6%) where the actions of another vehicle driver caused the collision, in thirteen of these cases the motorcycles had their lights switched on. The remaining n.22 collisions (56.4%) were due to the actions of the motorcyclist. In the approach to the collision scene, there were n.13 cases (31.7%) in which the approach was a right hand bend and in n.8 (19.5%) cases, the approach was a left hand bend. In the remaining n.18 (43.9%) cases, the approach was a straight road. Of the n.17 (41.4%) motorcycles that slid after falling, n.10 (24.4%) fell onto their right side and the remaining n.7 (17.1%) fell onto their left side. The information from this study identifies primary and contributory causes of motorcycle collisions.
This thesis gives a detailed picture of how planners, politicians, residents and transport engineers in three societies, Britain, Germany and the United States reacted to one of the most powerful inventions of the late nineteenth century, the motor car. Misjudgments of the potential growth of motor vehicle ownership and its adverse effects had serious repercussions in the coming decades, primarily in the dense urban areas. Disturbing has been the underestimation of the importance of public transport as a real alternative to the motor car in urban areas, first by the United States and even several decades later by Britain. Of the three countries, only Germany seems to have struck a better balance. Not surprisingly, already at the beginning of the twentieth century, conflicts occurred between the weaker road participants (pedestrians and cyclists), the existing urban fabric and the motor vehicle. A more comprehensive comparison between Britain and Germany shows that both countries developed specific patterns and had different attitudes towards road transport. Far more has been invested and planned in Germany whereas Britain has shown not so much a lack of foresight in planning but 'in investment in road transport. This major difference has had very visible effects an today's urban structure and transport situation. The demand for restraint of motor traffic had different motives in the two countries, and is not such a new idea as is often assumed. While in Germany even in the 1920s and 30s the protection of historic inheritance was a decisive motive, in Britain that was not the case. Questions of traffic restraint were however raised in connection with road safety and later in the 60s as a means of improving the urban environment. The turning point of nearly unlimited promotion of car use in urban areas took place in Germany during the 60s and 70s, whereas the Buchanan Report had already warned in the early 60s against the adverse effects cars could have in urban areas if they were not controlled. Although even in Britain the report was misunderstood and largely not put into practice, the wave of protest against road building occurred earlier there than in Germany. As a whole, Britain has shown a brillance of ideas in restraining motor vehicles which was lacking in the Federal Republic. At the beginning of the 70s, discussions started seriously in Germany an traffic calming concepts which were slowly transformed into reality, Britain seems to have followed these examples, but with a considerable time lag.
The proportion of older road users is increasing because of demographic change (in the group 65+ from current 18% to about 24% by 2030). The mobility needs of people 65+ often differ from those of younger people. Seniors (65+) are already more involved in fatal accidents than younger road users. According to the age development, the senior share of road deaths in the EU of today is increasing nearly one-fifth to one-third. From the in-depth analysis of accidents generic simulation models were developed. Attention has been paid both to psycho-physical characteristics as well as on the social and physical environment and their specifics in conjunction with seniors. By simulating the defined scenarios and varying the defined relevant parameters, accident influencing factors were examined as a basis for avoidance. In addition, the parameters were varied to show the influence from the vehicle, the pedestrian and the infrastructure to avoid the accident or to characterize the conditions for which the accident is inevitable.
Nowadays human-created systems are increasing in complexity due to the interaction of humans and technology. Especially road traffic systems are composed of multitudinous resources (e.g. personnel, vehicles, organizations, etc.), which make it even harder to anticipate the positive and negative effects on safety. One key in achieving a significant reduction of fatalities is seen in driver assistant systems counterbalancing the lack of drivers' capabilities. But the actual outcome of implementing these sophisticated technologies especially on influencing driver's capabilities are yet unknown. Latest research exemplifies an increase of reaction times of drivers in case of dysfunctional driver assistant systems. This research paper applies STAMP/STPA (STAMP = systems-theoretic accident model and processes; STPA = systems-theoretic process analysis) to the German automobile traffic system focusing on the effects of driver assistant systems on drivers. By doing so, the potential hazards caused by technology can be identified.