Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (637) (entfernen)
Schlagworte
- Conference (386)
- Konferenz (382)
- Germany (212)
- Deutschland (209)
- Unfall (188)
- Accident (187)
- Safety (123)
- Sicherheit (122)
- Injury (117)
- Verletzung (117)
Institut
A biofidelic flexible pedestrian legform impactor (FlexPLI) has been developed from the year 2000 onwards and evaluated by a technical evaluation group (Flex-TEG) of UN-ECE GRSP. A recently established UN-ECE GRSP Informal Group on GTR9 Phase 2 is aiming at introducing the FlexPLI within world-wide regulations on pedestrian safety (Phase 2 of GTR No. 9 as well as the new UN regulation 127 on pedestrian safety) as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents. Besides, the FlexPLI has already been introduced within JNCAP and is on the Euro NCAP roadmap for 2014. Despite of the biofidelic properties in the knee and tibia sections, several open issues related to the FlexPLI, like the estimation of the cost benefit, the feasibility of vehicle compliance with the threshold values, the robustness of the impactor and of the test results, the comparability between prototype and production level and the finalization of certification corridors still needed to be solved. Furthermore, discussions with stakeholders about a harmonized lower legform to bumper test area are still going on. This paper describes several studies carried out by the Federal Highway Research Institute (BASt) regarding the benefit due to the introduction of the FlexPLI within legislation for type approval, the robustness of test results, the establishment of new assembly certification corridors and a proposal for a harmonized legform to bumper test area. Furthermore, a report on vehicle tests that previously had been carried out with three prototype legforms and were now being repeated using legforms with serial production status, is given. Finally, the paper gives a status report on the ongoing simulation and testing activities with respect to the development and evaluation of an improved test procedure with upper body mass for assessing pedestrian femur injuries.
The practicability and feasibility of using alcohol ignition interlock devices has been discussed for more than 15 years in Germany. Thereby, judicial issues have been treated conversely. Consensus exists about the fact that the voluntary use of alcohol ignition interlocks is in all areas of possible use recommendable. Great reservation is shown concerning the operation of the devices for DUI (Driving Under Influence) offenders. Main doubts regard the missing legal base for application in such cases and potential circumvention attempts while the need of supportive psychological measures is unquestioned. In 2011, the Ministry of Transport, Building and Urban Affairs entered this topic in its newly released traffic safety programme as a matter of future research. Almost in parallel, the Federal Highway Research Institute (BASt) launched an alcohol ignition interlock project for DUI offenders. The study at hand aimed at developing a comprehensive programme concept for the use of alcohol ignition interlocks as additional measure to psychological rehabilitation for DUI offenders. Expert surveys serve as input for the establishment of a widely accepted innovative concept for nationwide implementation. By means of a pilot trial, the added value of using a combination of structural (alcohol interlock) and individual (psychological measure) intervention for DUI offenders to the existing countermeasure system should be studied. In addition, selection criteria for DUI offenders eligible for future programme participation should be defined. The majority of the experts evaluate the introduction of alcohol ignition interlocks as a good option to enhance traffic safety. The possibility of early psychological rehabilitation is emphasized in the process. Those who do not approve alcohol ignition interlock usage estimate the amount of offenders eligible for such programmes too small. The survey also revealed that legal regulations for issuing an alcohol interlock restricted licence to DUI offenders is missing. Hence, a possible amendment to the German Driving Licencing Regulation was developed within the project. Consultations with the Ministry of Transport, Building and Urban Affairs and the Ministry of Justice disclosed the need for a change of the road traffic law before an amendment to the existing regulations may be put into force. At least, the person responsible in the Ministry of Justice developed a proposal for the law section that needs revision. All in all, it became clear within the process of the project that a field trial in Germany is still a distant vision. Nevertheless, all institutions involved are motivated to deal with the matter further on in order to pave the way for a soon start of the pilot trial.
In Germany, courses for the restoration of the fitness to drive after licence revocation are provided for different offender groups (alcohol, drug and demerit point offenders). Providers of these courses are by law required to prove the effectiveness of the applied course programs. For the evaluation of effectiveness, the Federal Highway Research Institute (BASt) established specific "Reference Values" in 2002. The objective of the study at hand was to collect valid data in order to renew the old-established Reference Values from 2002. Additionally, data collection aimed at initializing Reference Values for drug offender programs. Over 66,000 drivers were analysed regarding their traffic probation in the three years after licence reinstatement. Offenders were assigned to an offender group (alcohol, drugs and demerit point offenders) based on the reason for prior licence revocation. Different indicators were used as criteria for re-offending: new alcohol or drug records, culpable accident involvement and repeated licence revocation. For each of the offender groups, frequency distributions regarding these indicators were calculated. Frequencies of recidivism are highest for the group of demerit point offenders. Compared to the Reference Values of this group from 2002, frequencies of re-offending increased. Conversely, re-offence frequencies of alcohol offenders are halved compared to the data from 2001. The analysis of the re-offence frequencies of drug offenders reveals an equal amount of re-offenders as in the alcohol offender group. The collected data serve as a good base for renewal of the old-established Reference Values and may be applicable as comparative data for future evaluations The results reveal significant differences between recent data and earlier studies. These may occur due to improvements of the applied programmes, but also due to situational changes, e.g. increased enforcement levels and expansion of the catalogue of offenses which lead to demerit points.
The misuse of CRS (child restraint system) is one of the most urgent problems in connection of child safety in cars. Numerous field studies show that more than two thirds of all CRS are used in a wrong way. This misuse could lead to serious injuries for the children. Surprisingly the quality of CRS use is coded much better in accident data (e.g. GIDAS) than the results of observatory field studies show. It is expected that misuse of CRS was not detected by the accident teams in a large number of the cases. An essential part in improving child seats and their usability is the knowledge of the relation between misuse and resulting injuries. For that the analysis and experimental reconstruction of accidents is an important part. For allowing an exact experimental accident reconstruction, it is necessary to have detailed information about the securing situation of the child and about the installation of the CRS in the car.
This paper will outline ETSC's contribution to the European Union's road safety policy 2011-2020. It will present some of the main recommendations from ETSC's Blueprint for the 4th Road Safety Action Programme and will introduce the response to the European Commission's Road Safety Policy Orientations 2011-2020 (published July 2010). The second framework document presented is the Transport White Paper (published March 2011). The paper will focus on new targets and the new vision set for Europe's Road Safety policy picking out some issues in particular such as traffic law enforcement and the protection of vulnerable road users. It will argue that by reinforcing the current Road Safety Policy Orientations, the EU will be better placed to reach its new ambitious goal of halving road deaths by 2020 and the longer term zero casualty vision.
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
Various kinds of demerit point systems have been developed and implemented in European countries, aimed at tackling repeat offences in road transport by acting as a deterrent and providing sanctioning. The impact of a demerit point system on the number of crashes is often reported to be significant, but temporary. The objective of the EU BestPoint project was to establish a set of recommended practices that would result in a more effective and sustainable contribution of demerit point systems to road safety. A high actual chance of losing the licence and a high perceived chance of losing the licence are basic prerequisites for the effective operation of demerit point systems. For measures applied within the context of a demerit point system, a four-step-approach is recommended: warning letter, driver improvement course, licence withdrawal, rehabilitation course. Further recommendations concern issues like points and offences, e.g. which offences should lead to points, target groups, and the administration of demerit point systems. The final result of the EU BestPoint project is a handbook (van Schagen & Machata, 2012) which provides a concise overview of all recommended practices. The presentation/paper outlines how sustainable safety improvements can be achieved if national demerit point systems are implemented and maintained according to the recommended practices. In addition, potential further steps towards an EU-wide demerit point system (cross-border exchange on points and/or offences) are presented.
The German highway network hast o face new challenges in the near future, e.g. increasing traffic density and loads, climate change effects and new quality requirements regarding sustainability. It is necessary to come up with foresighted concepts in the present to be prepared for these challenges. Therefore it is important to adapt and enhance innovative attempts, which take changing impacts into account. One goal of these efforts is the development of adaptive systems for the provision of information and a holistic evaluation in real time. The paper describes the recent research and developments on a system for information and holistic evaluation in real time, taking into account sensor networks, evaluation procedures and their implementation in existing maintenance and inspection strategies.
Am 42. Erfahrungsaustausch über Erdarbeiten im Straßenbau (EAT) am 5. und 6. Mai 2010 nahmen neben Vertretern des Bundesministeriums für Verkehr, Bau- und Stadtentwicklung und der Straßenbaubehörden der Länder auch Vertreter der Bundesanstalt für Wasserbau, der Deutschen Bahn AG und der DEGES teil. Der Erfahrungsaustausch dient dazu, Erfahrungen mit neuen Bauweisen und der Anwendung neuer Regelwerke und Prüfverfahren mitzuteilen und zu diskutieren. Der 42. EAT hatte vier verschiedene Themen-Schwerpunkte. Zum Einen "Regelwerke und Normung", es wurde die Arbeitsgruppe des CEN und deren Aufgaben bei der europäischen Normung "Erdarbeiten" vorgestellt, über die Qualitätssicherung von Geokunststoffen informiert und außerdem Neuerungen in den RAP Stra 2010 und der aktuelle Überarbeitungsstand der Richtlinien für die Straßenentwässerung (ZTV Ew, RiStWag und RAS-Ew) erläutert. Die Erfahrungsberichte gewährten Einblicke über neue Bauverfahren und Baustoffe. Es wurde der Vortrag vom 41. EAT über die Anwendung von Glasschaumgranulat als Leichtschüttung mit 2-jähriger Erfahrung fortgeführt. Ferner wurde über die Verbesserung des Verformungsverhaltens organischer Böden am Beispiel der Querung eines Moorgebietes in Brandenburg und der Überwindung eines Todeisloches beim Bau der A7 im Allgäu berichtet. Ebenfalls wurden die Vorteile und erforderlichen Einschränkungen (Risiken) der Beobachtungsmethode bei der Sicherung standsicherheitsgefährdeter Einschnittsböschungen erläutert. Ein weiteres Thema waren die Auswirkungen des Klimawandels auf die Straßeninfrastruktur. In verschiedenen Szenarien wurde über den Klimawandel mit Relevanz für die Straße und über Risiken von Hang- und Böschungsrutschungen durch die Zunahme von Extremwetterereignissen informiert. An drei Fallbeispielen in Baden Württemberg, Rheinland-Pfalz und Niedersachsen wurde über Böschungsrutschungen und deren Sanierungsmaßnahmen berichtet. Den letzten Schwerpunkt bildeten die Bauverträge mit funktionalen Anforderungen. Es wurde über den Funktionsbauvertrag im Bundesfernstraßenbau, die Vorstellung der ZTV-Funktion E an Hand der BAB A6 bei Nürnberg und über die ZTV Funktion Ew berichtet. Die Fachexkursion am 6. Mai 2010 führte zunächst zur Verkehrs- und Betriebszentrale Nordbayern, die eindrucksvoll über ihre Aufgabengebiete, einschließlich des verkehrstelematischen, betriebs- und tunneltechnischen Systems informierte. Anschließend wurde über weitere Details des sechsstreifigen Ausbaus der BAB A6 zwischen der AS Roth und dem AK Nürnberg-Süd informiert. Im Anschluss erfolgten unter fachkundiger Führung die Besichtigung der Erdbaumaßnahmen an der Main-Donau-Kanalbrücke und der Rückbau des Lärmschutzwalls Kornburg inklusive der Erläuterungen der unvorhergesehenen Probleme bei der Aufbereitung des alten Lärmschutzwalls.