Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (637) (entfernen)
Schlagworte
- Conference (386)
- Konferenz (382)
- Germany (212)
- Deutschland (209)
- Unfall (188)
- Accident (187)
- Safety (123)
- Sicherheit (122)
- Injury (117)
- Verletzung (117)
Institut
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
Bis zum Jahr 2000 erfolgte die Überarbeitung der Begutachtungsleitlinien zur Kraftfahrereignung stets als Gesamtwerk, in Zusammenarbeit mit den Fachgesellschaften und herausgegeben von einem Wissenschaftlichen Beirat. Diese Art der Veröffentlichung erwies sich aus verschiedenen Gründen als nicht mehr praktikabel. Von Anwenderseite wurde der Wunsch nach besserer Übersicht geäußert und es hat sich gezeigt, dass mehr Detailinformation erforderlich ist. Es wird auf die zukünftige Gestaltung und Veröffentlichung der Leitlinien eingegangen, die nun die kapitelweise Überarbeitung als Methode der Wahl definieren. Die freie Verfügbarkeit als elektronisches Dokument soll die Verbreitung weiter erhöhen, die Suche nach Begriffen vereinfachen und eine schnellere Aktualisierung ermöglichen. Änderungen bei der Europäischen Führerscheinrichtlinie (Annex III) sowie bei deren Umsetzung in Deutschland (Anlage 4 der Fahrerlaubnisverordnung) gingen Überarbeitungen bei verschiedenen Kapiteln der Begutachtungsleitlinien voraus. Schon seit 2009 veröffentlicht ist das überarbeitete Kapitel "Epilepsie". Es wird auf die Änderungen in den Kapiteln Diabetes, Tagesschläfrigkeit, Hörvermögen und Gleichgewicht eingegangen, die als nächste folgen sollen. Für den Abstimmungsprozess mit Bund und Ländern wurde das zukünftige Vorgehen bei Änderungsbedarf abgestimmt. Die Begutachtungsleitlinien sind kostenlos zum Download auf www.bast.de verfügbar, einschließlich ergänzender Informationen.
T. DÜNCHHEIM erörtert in seinem Einführungsvortrag zu "Die Stellung der Gemeinden im Straßenrecht" die kommunalen Gestaltungsspielräume hinsichtlich ihres Satzungsrechts, das sich auf -§ 19 StrWG NRW stützen lässt. Er schildert die Auswirkungen dieser Gestaltung auf das Straßen- und Straßenverkehrsrecht, die letztlich Ausfluss der gemeindlichen Selbstverwaltungsgarantie sind. Dabei problematisiert er die Abgrenzung zwischen straßenrechtlichem Gemeingebrauch und Sondernutzung sowie die Bedeutung der rechtlichen Ausgestaltung des Straßen- und Straßenverkehrsrechts. Hierbei wird die Anwendung des -§ 45 StVO durch die Gemeinden einer kritischen Analyse unterzogen. A. NETTER schildert in seinem Beitrag "Aktuelle Rechtsfragen der Ortsdurchfahrten" die Gremienstruktur im Straßenwesen und den Einfluss des Europarechts, des Bundes- und Landesstraßenrechts sowie den Ortsdurchfahrtenrichtlinien auf das Straßenwesen. Er stellt dabei die Folgen der Aufhebung der Radwegbenutzungspflicht sowie die aus der Straßenbaulast folgende Entwässerungsverpflichtung der Straßenbaulastträger und ihre Umsetzung in den Gemeinden dar. U. WEGNER berichtet in ihrem Beitrag "Aktuelle Entwicklungen des Verbandsklagerechts" über die Auswirkungen europäischer Richtlinien auf das Umweltrecht. In diesem Zusammenhang wird eine wegweisende Entscheidung des BVerwG erörtert, welche die direkte Anwendung des Art. 9 Abs. 3 AK zum Gegenstand hat. Trotz der Einführung einer bundesrechtlichen Verbandsklage in -§ 64 BNatSchG sei das Problem der Wahrung von Allgemeininteressen nicht gelöst, da diese Norm die Interessen des Umweltschutzes nicht hinreichend zu schützen vermöge. Der Beitrag "Inanspruchnahme öffentlicher Wege durch TK-Unternehmen" von U. STELKENS, stellt eine differenzierte Auseinandersetzung mit dem TKG-Wegerecht dar. Er konstatiert, dass die Bestimmungen des TKG im Wesentlichen auf den Normen des Telegraphenwegegesetz (TWG) basieren. Daher bestehen Spannungsverhältnisse und Reibungsflächen zwischen den verschiedenen Abschnitten des TKG, da das TKG und das TWG unterschiedliche Ziele verfolgen. Beispielsweise seien die -§ 77a bis -§ 77e TKG nicht auf die -§ 68 bis -§ 77 TKG abgestimmt worden. Der abschließende Beitrag "Fachplanerische Auswirkungen des Umweltschadensgesetzes" von M. PETERSEN widmet sich der Frage, ob und welche Auswirkungen das Umweltschadensgesetz auf das Fachplanungsrecht hat. Zunächst wird allgemein herausgearbeitet, dass das Umweltschadensgesetz nicht Schadensersatz- oder Ausgleichsleistungen eines geschädigten Dritten bezweckt; vielmehr sollen Umweltschäden vermieden und die Wiederherstellung geschädigter Umweltgüter erreicht werden. Die Frage, ob und inwieweit das Umweltschadensgesetz Auswirkungen auf das Fachplanungsrecht hat, hängt davon ab, ob die Haftungstatbestände des -§ 3 Abs. 1 USchadG einschlägig sind.
Structured road markings are becoming popular as edge line on high speed roads, ensuring night time visibility (retroreflection) during rain. These markings are often also "audio-tactile": vehicles (un)intentionally driving over it may produce much more tyre/road sound, which may be observed in the vehicle but also in the vicinity. The sound increase inside the car can be considered as a positive side effect, as it alarms the driver and may be very helpful for the prevention of "doze off" traffic accidents. The sound increase perceived outside the car however, may have a positive aspect as it can warn people on the emergency lane about the approaching vehicle, but it may as well annoy people living around. A method for the assessment of the acoustic properties of audio-tactile markings has been developed. It is mainly based on the "Close Proximity" (CPX) method, an ISO method intended for the acoustic assessment of pavements. The results of measurement campaigns with CPX trailers in Belgium and Germany according to a specially designed procedure are presented. The feasibility of the method is discussed. The research has been carried out in the frame of the standardization activities of the CEN working group CEN/TC226/WG2 "Horizontal signalization".
The use of alcohol interlocks for DUI offenders is widespread around the world. in North America and Australia alcohol interlocks are core elements in the countermeasure system against DUI recidivism. Based on a European experience exchange hosted by the Federal Highway Research Institute (BASt) in October 2013, key features of European alcohol interlock programmes are illustrated. In addition, key findings from international alcohol interlock research are presented. They point towards a need for an accompanying rehabilitative measure in order to achieve long-lasting behavioural changes in the offender. Data from the interlock recorder can be used as predictor for recidivism risk, but also as objective data to aid counselling. Finally, an example of an accompanying rehabilitative measure, which was specifically developed for interlock programmes within a BASt project, is given.
The German highway network is facing new challenges in the near future. The structures have to deal with increasing traffic loads, climate change effects and new requirements regarding sustainability while they are getting older and budget cuts can be expected. To guarantee a reliable highway network, it will be vital to adapt and enhance innovative approaches. Current bridge management relies on the results of conventional bridge inspections and thus has certain limitations when it comes to insufficient load bearing capacity and other systematic weaknesses. Therefore, new approaches for real time condition assessment of critical road infrastructure elements are to be developed.
In 2012 the fifth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
The utilisation of secondary-safety systems to protect occupants has attained a very high level over the past decades. Further improvements are still possible, but increasingly minor progress is only to be had with a high degree of effort. Thus, a key aspect must be the impact to overall safety in an accident. If reliable information is available on an imminent crash, measures already taken in the pre-crash phase can result in a significantly great influence on the outcomes of the crash. With this background preventive measures are the key to a sustainable further reduction of the figures of crash victims on our roads. This paper aims to show a preventive approach that can contribute to lessening the consequences of a crash by creating an optimum interaction of measures in the fields of primary and secondary safety. To further enhance vehicle safety, driver assistant systems are already available that warn the driver of an imminent front-to-rear-end crash. The next step is to support him in his reactions or if he fails to react sufficiently, to even initiate an automatic braking when the crash becomes unavoidable. Automatic pre-crash braking can, in an ideal situation, fully prevent a crash or can significantly reduce the impact speed and thus the impact energy (and the severity of the accident). If a vehicle is being braked in the pre-crash phase, the occupants are already being pre-stressed by the deceleration. The information available about the imminent crash can be used to activate the belt tensioners and likewise other secondary safety systems in the vehicle right before the impact. The pre-crash deceleration also causes the front of the vehicle to dip. Conventional crash tests do not take this specific impact situation into consideration. This is why, for example, the influences of the pre-crash displacements of the occupants are not recorded in the test results. Furthermore, a reproducible representation of the benefit of the vehicle safety systems which prepare the occupants for the imminent impact is not possible. In order to demonstrate the functions of automated pre-crash braking and to investigate the differences during the impact as a consequence of the altered occupant positions as well as the initiation of force and deformations of the vehicle front, DEKRA teamed up with BMW to carry out a joint crash test with the latest BMW 5 series vehicle. It involved the vehicle braking automatically from a starting test speed of 64 km/h (corresponding to the impact speed set by Euro NCAP) down to 40 km/h. The test was still run by the intelligent drive system of the crash test facility. This required several modifications to be made to the test facility as well as to the vehicle. The paper will describe and discuss some relevant results of the crash test. In addition, the possible benefits of such systems will also be considered. The test supplemented the work of the vFSS working group (vFSS stands advanced Forward-looking Safety Systems).
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of synthetic and plastic materials as a material for the interior equipment of buses and coaches because of their ood mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years - also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, the production of smoke, the smoke development and propagation and its toxicity for the people as well as the testing methods and limit values are of interest. For those reasons research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behavior of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and on-board extinguishing equipment were elaborated. At the other hand research is carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. The paper describes which effective and economically reasonable fire safety requirements for interiors of buses would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses.