Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (121) (entfernen)
Schlagworte
- Safety (37)
- Sicherheit (37)
- Test method (37)
- Prüfverfahren (35)
- Conference (33)
- Konferenz (33)
- Bewertung (32)
- Evaluation (assessment) (31)
- Fahrzeug (30)
- Impact test (veh) (30)
Institut
- Abteilung Fahrzeugtechnik (121) (entfernen)
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
According to the German road traffic regulations children up to the age of 12 or a height below 150 cm have to use approved and appropriate child restraint systems (CRS). CRS must be approved according to UN-ECE Regulation No. 44. The regulation classifies CRS in 5 weight categories. The upper weight group is approved for children from 22 to 36 kg. However, studies show that already today many children weigh more than 36 kg although they have not reached a height of 150 cm. Therefore, no ECE R44 approved CRS is available for these overweight children. In conclusion, today's sizes and weights of children are no longer represented by the current version of the ECE R44. The heaviest used dummy (P10) weighs just 32.6 kg and has a height of 137.9 cm. Statistical data of German children show that already 5% of the children at a height of 137.9 cm have a weight above 45.3 kg. Regarding children at a height of 145 cm, the 95th percentile limit is at a weight of 53.3 kg. Based on these data 4 dummies with different heights and weights were defined and produced. Two of them are overweight. Up to now, there is no experience how current child restraint systems perform in a car crash if they are used by children with a weight above 36 kg and a height smaller than 150 cm. In the future, different child restraint systems will be tested with respect to the ECE R44 regulation using these overweight dummies.
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
The main objective of EC CASPER research project is to reduce fatalities and injuries of children travelling in cars. Accidents involving children were investigated, modelling of human being and tools for dummies were advanced, a survey for the diagnosis of child safety was carried out and demands and applications were analysed. From the many research tasks of the CASPER project, the intention of this paper is to address the following: • In-depth investigation of accidents and accident reconstruction. These will provide important points for the injury risk curve, in order to improve it. Different accident investigation teams collected data from real road accidents, involving child car passengers, in five different European countries. Then, a selection of the most appropriate cases for the injury risk curve and the purposes of the project was made for an in-depth analysis. The final stage of this analysis was to conduct an accident reconstruction to validate the results obtained. The in-depth analysis included on-scene accident investigation, creating virtual simulations of the accident/possible reconstruction, and conducting the reconstruction. In the cases of successful reconstructions, new points were introduced to the injury risk curves. Accident reconstructions of selected cases were carried out in test laboratories as the next step following in-depth road accident investigation. These cases were reconstructed using similar child restraint systems (CRS) and the same type make and model as in the real accidents. Reconstructing real cases has several limitations, such as crash angle, cars" approximation paths and crash speed. However, a few changes and applications on the testing conditions were applied to reduce the limitations and improved the representations of the real accidents. After conducting the reconstructions, a comparison between the deformations of the cars on the real accident and the vehicles from the reconstructions was made. Additionally, a correlation between the data captured from the dummies and the injury data from the real accident was sought. This finalises an in-depth analysis of the accident, which will provide new relevant points to the injury risk curve. The CASPER project conducted a large research programme on child safety. On technical points, a promising research area is the developing injury risk curves as a result of in-depth accident investigations and reconstructions. This abstract was written whilst the project was not yet finished and final results are not yet known, but they will be available by the time of the conference. All the works and findings will not necessarily be integrated in the industrial versions of evaluation tools as the CASPER project is a research program.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
Qualität von on-trip Verkehrsinformationen im Straßenverkehr : BASt-Kolloquium 23. und 24.03.2011
(2011)
Am 23. und 24. März 2011 veranstaltete die Bundesanstalt fuer Straßenwesen ein, um die Ergebnisse der erwähnten Projekte und Initiativen präsentieren zu lassen und mit anderen Experten zu diskutieren. Der vorliegende Tagungsband fasst die Ergebnisse des Kolloquiums zur "Qualität von on-trip Verkehrsinformationen" zusammen. Die Bereitstellung von Verkehrsinformationen ist geprägt von vielen Akteuren. Die Wertschöpfungskette beginnt bei der Sammlung grundlegender Verkehrsdaten zur Erstellung von Verkehrsinformationen und setzt sich mit der Datenverarbeitung und -interpretation bis hin zur Meldungserstellung fort. Die Weitergabe kann über verschiedene Übertragungsmedien erfolgen und beim Nutzer (z.B. im Navigationsgerät) empfangen werden. Jeder einzelne Schritt der Wertschoepfungskette kann sowohl von unterschiedlichen Partnern (privat oder öffentlich) übernommen werden als auch in der Hand eines Partners liegen. Diese Komplexität der Zusammenarbeit spiegelt sich demzufolge auch in Qualitätsmanagementprozessen wider. Im Rahmen des Kolloquiums wurden zwei wesentliche Qualitätsaspekte näher betrachtet: - die Datenqualität mit dem Focus auf Aktualitaet, Stimmigkeit der Daten verglichen mit einer gemessenen Realitaet sowohl zu Beginn der Wertschöpfungskette als auch an jeglichen Schnittstellen, - die Prozessqualität, welche sich insbesondere mit der reibungslosen Datenübergabe an den Schnittstellen der Wertschoepfungskette beschäftigt. Beide Qualitätsaspekte helfen zu verstehen, worin die heutigen Qualitätsprobleme bestehen und welche Massnahmen im Einzelnen ergriffen werden müssten, um eine nachhaltige Verbesserung zu erreichen. Einerseits kann es vorkommen, dass die Information über ein Verkehrsereignis an einer oder mehreren Stellen der Wertschöpfungskette korrekt vorliegt, jedoch durch ungenuegende technische oder organisatorische Schnittstellen im Prozessablauf wieder verloren geht und dem Nutzer folglich nicht zur Verfügung steht. Prominentes Beispiel eines solchen Problems in der Prozessqualität ist die fehlerhafte Interpretation der Meldung im Navigationsgerät, denkbar sind solche Informationsverluste jedoch an jeder Stelle der Wertschoepfungskette. Eine wichtige Massnahme zur Verbesserung der Prozessqualität ist die Standardisierung sowie die Überprüfung, ob die definierten Standards an jeder Stelle der Wertschöpfungskette eingehalten werden. Andererseits kann es vorkommen, dass die Datenqualität in Bezug auf ihre Genauigkeit von Anfang an so schlecht ist, dass der Nutzer eine fehlerhafte oder gar keine Nachricht übermittelt bekommt. Beispiel hierfür ist die Vielzahl von Stauereignissen, die entweder nicht gesendet wurden oder gesendet wurden, obwohl sie nicht vorhanden waren. Eine wichtige Massnahme zur Verbesserung dieser Situation ist die Verbesserung der Ereignisdetektion. Der Tagungsband enthaelt Präsentationen, die den Status Quo analysieren, Methoden zur verbesserten Datenerfassung vorschlagen und Möglichkeiten zur Verbesserung von Daten- und Prozessqualität vorstellen. Offen geblieben sind darüber hinaus folgende Fragestellungen: - Wie kann die Prozessqualität der gesamten Wertschöpfungskette bei der Vielzahl der Partner kontrolliert werden? Wer überwacht die Wertschöpfungskette? Wird hierfuer überhaupt eine zentrale Stelle benötigt? Oder ist es ausreichend, wenn jeder Partner eine angemessene Eingangs bzw. Ausgangskontrolle durchführt? - Obwohl es nur eine Realität gibt, entsteht doch Wettbewerb über die (Qualität der) Information zu dieser Realität. Wie kann Konsistenz zwischen allen Anbietern von sicherheitsrelevanten Informationen erreicht werden? Wo sollte der Wettbewerb enden und wie kann dies technisch, organisatorisch und wirtschaftlich realisiert werden? - Welche Prozesse sollten geschaffen werden, um Partner zu integrieren, die sich nicht an geschaffene Qualitätsstandards halten (z.B. kommerzielle Diensteanbieter, die nicht mit der Verkehrsinformationsszene vernetzt sind)? - Und nicht zuletzt, wie kann die Wahrnehmung des Nutzers über verschiedene Qualitätslevel unterschiedlicher Produkte verbessert werden? Ist der Nutzer in der Lage, die unterschiedlichen Qualitätsstufen von Verkehrssystemen zu unterscheiden? Falls nicht, welche Art von Unterstuetzung braucht der Kunde? Ein "European Information Services Assessment Programme" vergleichbar zu Euro NCAP für Fahrzeuge? Die Ergebnisse des Kolloquiums sollen die laufende Diskussion um die Verbesserung der Qualität von Verkehrsinformationen unterstützen.
Today, Euro NCAP is a well established rating system for passive car safety. The significance of the ratings must however be evaluated by comparison with national accident data. For this purpose accidents with involvement of two passenger cars have been taken from the German National Road Accident Register (record years 1998 to 2004) to evaluate the results of the NCAP frontal impact test configuration. Injury data from both drivers involved in frontal car to car collisions have been sampled and have been compared, using a "Bradley Terry Model" which is well established in the area of paired comparisons. Confounders " like mass ratio of the cars involved, gender of the driver, etc. " have been accounted for in the statistical model. Applying the Bradley Terry Model to the national accident data the safety ranking from Euro NCAP has been validated (safety level: 1star <2 star <3 star <4 star). Significant safety differences are found between cars of the 1 and 2 star category as compared to cars of the 3 and 4 star category. The impact of the mass ratio was highly significant and most influential. Changing the mass ratio by an amount of 10% will raise the chance for the driver of the heavier car to get better off by about 18%. The impact of driver gender was again highly significant, showing a nearly 2 times lower injury risk for male drivers. With regard to the NCAP rating drivers of a high rated car are more than 2 times more probable (70% chance) to get off less injured in a frontal collision as compared to the driver of a low rated car.
Since 2005 the German In-Depth Accident Study (GIDAS) also records aspects of active vehicle safety. This is done because vehicles are fitted with an increasing number of active safety devices which have undoubtedly an influence on the number, severity and course of accidents. Accident researchers expect that collecting active safety data will facilitate to assess and quantify the impact of these and future devices. It is the aim of this paper to outline benefits and limitations associated with the recording of active safety aspects within indepth studies. An overview about possible areas where active safety data can be useful will be given. For that purpose single safety or comfort systems will be selected to estimate the effects of an accident database which includes variables associated with these systems. Questions with regard to the limitations of collecting active safety data will be addressed. Possible items are for example the usability of the data recorded, the real accident cause, the small number of relevant accidents, the time span needed to gather a sufficient dataset, the small share of vehicles equipped with a certain system or different functionalities of systems that are supposed to fall in the same category. As a result user needs for a reasonable data collection of active safety elements will be elaborated.
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.
This paper describes the methodology for the assessment of the socio-economic impact of SAFESPOT applications. The applications selected for the assessment cover vehicle to vehicle (v2v) as well as vehicle to infrastructure (v2i) communication systems. The applications address main problem areas of road safety: accidents at intersections, accidents due to hazardous road and weather conditions and accidents due to over speeding and inappropriate distance. The assessment methodology relies in its core on cost-benefit analysis (CBA) as the most widespread tool to assess the profitability of applications form the society point of view. The assessment is however not limited to CBA but also considers the economic effects for particular stakeholder groups such as users, public authorities and the like. Their individual cost and benefits can be investigated in stakeholder analyses. Both elements, CBA and stakeholder analysis, form an integrated assessment approach which is applied here. The assessment makes use of the sound methodological base which was provided by projects such as SEiSS and eIMPACT. Some characteristics of co-operative systems however call for special attention within the assessment. Most prominently, the assessment will concentrate on a bundle of applications. The impact of this bundle will be assessed under the conditions of different business and service models. These issues will be addressed in the paper. Moreover, this paper also provides insight in likely patterns of results and first results of socio-economic impact assessment itself.
Mit der EU-Verordnung Nummer 661/2009 zur Typgenehmigung und allgemeinen Sicherheit von Kraftfahrzeugen wird von der EU für schwere Nutzfahrzeuge der Einbau von Spurverlassenswarnsystemen und automatischen Notbremssystemen vorgeschrieben. Mit dem obligatorischen Einbau der Systeme wird eine Reduktion der Abkommens- und Auffahrunfälle von Nutzfahrzeugen aus den Klassen M2, M3, N2 und N3, die auf Grund der hohen Masse der Fahrzeuge folgenschwer sind, erwartet. Als Einführungsdaten werden der 1. November 2013 für neue Fahrzeugtypen und der 1. November 2015 für neue Fahrzeuge genannt. Leistungsanforderungen beziehungsweise technische Spezifikationen, denen die Systeme genügen müssen, liegen jedoch noch nicht vor. Diese werden derzeit von einer Expertengruppe auf UN-ECE-Ebene entwickelt. Dabei wird versucht, technologieneutrale Beschreibungen für die Ausgestaltung der Systeme zu erstellen, die gleichzeitig sowohl den gewünschten Nutzen für die Verkehrssicherheit garantieren, sich aber auch an der derzeit vorhandenen und realisierbaren Technologie orientieren. Darüber hinaus müssen die Systemkosten in einem vernünftigen Verhältnis zum Sicherheitsnutzen stehen. Ziel ist es, im Laufe des Jahres 2011 Vorschläge für die Legislative vorzulegen. Es wird über den Stand der Arbeiten, offene Fragestellungen, Herausforderungen bei der Ausgestaltung der technischen Anforderungen sowie sich abzeichnende Ergebnisse berichtet. Dabei sind die Arbeiten in Bezug auf Lane Departure Warning Systems (LDWS) bereits weiter fortgeschritten als zu Advanced Emergency Braking Systems (AEBS).
In spite of today's highly sophisticated crash test procedures like the different NCAP programs running world-wide, bad real world crash performance of cars is still an issue. There are crash situations which are not sufficiently represented by actual test configurations. This is especially true for car to car, as well as for car to object impacts. The paper describes reasons for this bad performance. The reasons are in principal bad structural interaction between the car and its impact partners (geometric incompatibility), unadjusted front end stiffness (stiffness incompatibility) and collapse of passenger compartments. To show the efficiency of improving cars' structural behaviour in accidents with different impact partners an accident data analysis has been taken out by members of European Project VC-COMPAT. Accident data analysis has shown that in Germany between 15,000 and 20,000 of the now severely injured car occupants might get less injured and between 600 and 900 car occupant fatalities might be saved. Similar results arise for the UK.
Zum gegenwärtigen Zeitpunkt werden verschiedene Ansätze diskutiert, wie der Verbesserung der Straßenverkehrssicherheit durch den Einsatz moderner Fahrerassistenzsysteme (FAS) neue Impulse gegeben werden können. Unter dem Dach der von der Europäischen Kommission gemeinsam mit der Industrie im Frühjahr 2002 ins Leben gerufenen eSafety-Initiative soll die Entwicklung und Implementierung "Intelligenter Integrierter Sicherheitssysteme" (Intelligent Integrated Road Safety Systems) koordiniert und vorangetrieben werden. Erwartet werden hiervon entscheidende Beiträge zur Erreichung der bis zum Jahr 2010 angestrebten Halbierung der Zahl der Verkehrstoten in Europa, entsprechend dem Weissbuch der Europäischen Kommission. Intelligente Unterstützung des Fahrers meint in diesem Zusammenhang die Berücksichtigung des Gesamtsystems "Fahrer-Fahrzeug-Umwelt". Für die fahrzeugseitige Umsetzung der Unterstützungsfunktion wurden verschiedene Ausformungsgrade (zum Beispiel Information, Warnung, korrigierender Eingriff) vorgeschlagen und entwickelt. Die BASt ist an einer Reihe von Projekten und Arbeitsgruppen beteiligt, die sich direkt oder indirekt mit Fragen befassen, die sich bei der Entwicklung und Bewertung intelligenter FAS zur Beeinflussung der Fahrzeuggeschwindigkeit stellen. Im Mittelpunkt stehen dabei vor allem Fragen der Sicherheitsbewertung und der Machbarkeit, wie zum Beispiel - Realisierung der fahrzeugseitigen Umsetzung, - Kosten-Nutzen-Gesichtspunkte, - Rechtliche Aspekte, - Voraussetzungen der Datenbasis. Beispielsweise ist die BASt an der von ERTICO koordinierten "SpeedAlert"-Initiative beteiligt. Ziel dieser Aktivität ist die europaweite Implementierung eines Geschwindigkeitswarnsystems. An der hierzu im Jahre 2001 gegründeten "SpeedAlert" Arbeitsgruppe beteiligen sich Industrie und Verwaltung.
In the framework of the OECD study "Moving Freight with Better Trucks", several vehicle combinations which are worldwide in operation were examined regarding different performance criteria. One criterion was the road wear performance of these articulated vehicles. With given tyre and vehicle data (mainly weights and axle loads) the road wear performance was calculated for each vehicle combination. The method according to COST 334 is presented and the vehicle combinations are compared
The objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria and limits for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configurations such as impacts with car sides, trucks, and pedestrians. The WG consists of national government representatives who are supported by industrial advisers. The WG serves as a focal point for European research conducted by national and industry sponsored projects. The WG is responsible for collating the results from this research to achieve its objectives. EEVC WG 15 serves as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the Development of Crash Test Procedures"(VC-COMPAT) project partly funded by the European Commission. This paper presents a review of the current European research status. It also identifies current issues with candidate test procedures and lists the parameters that should be considered in assessing compatibility. The current candidate test procedures are: an offset barrier test with the progressive deformable barrier (PDB) face; a full width wall test with or without a deformable aluminium honeycomb face and a high resolution load cell wall; an offset barrier test with the EEVC barrier and load cell wall. These candidate test procedures must allow assessment of structural interaction, frontal force levels and compartment strength. The WG will report its findings to the EEVC Steering Committee and propose a test procedure in November 2006.