Description of road traffic related knee injuries in published investigations is very heterogeneous. The purpose of this study was to estimate the risk of knee injuries in real world car impacts in Germany focusing vulnerable road users (pedestrians, bicyclists and motorcyclists) and restrained car drivers. The accident research unit analyses technical and medical data collected shortly after the accident at scene. Two different periods (years 1985-1993 and 1995-2003) were compared focusing on knee injuries (Abbreviated Injury Scale (AISKnee) 2/3). In order to determine the influences type of collision, direction and speed as well as the injury pattern and different injury scores (AIS, MAIS, ISS) were examined. 1.794 pedestrians, 742 motorcyclists, 2.728 bicyclists and 1.116 car drivers were extracted. 2% had serious ligamentous or bony injuries in relation to all injured. The risk of injury is higher for twowheelers than for pedestrians, but knee injury severity is higher for the latter group. Overall the current knee injury risk is low and significant reduced comparing both time periods (27%, p<0,0001). Severe injuries (AISKnee 2/3) were below 1%). Improved aerodynamic design of car fronts reduced the risk for severe knee injuries significantly (p=0,0015). Highest risk of injury is for motorcycle followed by pedestrians, respectively. Knee protectors could prevent injuries by reducing local forces. The classically described dashboard injury was rarely identified. The overall injury risk for knee injuries in road traffic is lower than estimated and reduced comparing both periods. The aerodynamic shape of current cars compared to older types reduced the incidence and severity of knee injuries. Further modification and optimization of the interior and exterior design could be a proper measurement. Classic described injury mechanisms were rarely identified. It seems that the AIS is still underestimating extremity injuries and their long term results.
Whiplash injuries are characterized by the high variability of its symptoms and by the subjectivity of its diagnosis, which sometimes leads to frauds perpetrated by victims of rear-end impacts. It is estimated that whiplash injuries cost annually about 10.000 million Euros in Europe. Therefore, the aim of this study was to investigate the influence of the dynamics of the accident in which the victim was involved in the probability of development of whiplash associated injuries. In the presented methodology, first an accident reconstruction is performed where the dynamics of the accident is determined. This is carried out using the software PC-Crash, police and insurance companies' data. Then biomechanical injuries criteria related with whiplash injuries are evaluated. For the evaluation of the probability of having whiplash injuries, the Neck Injury Criterion (NIC) of the victim and the mean acceleration of the vehicle were evaluated. Then, with medical reports, the results of the accident reconstruction are correlated with the reported injuries. Some examples are presented. The results obtained indicate that the study of the dynamics of the road accidents in which the victims were involved could be used as an auxiliary of the prognosis of whiplash injuries and is important for a precise diagnosis of this type of injuries.
The objective of the study is to measure the risk of pedestrian and bicyclist in urban traffic through an analysis of real-world accident data. The kinematics and injury mechanisms for both pedestrian and bicyclists are investigated to find the correlation of injury risks with injury related parameters. For this purpose, firstly 338 cases are selected as a sample from an IVAC accident database based on the In-depth Investigation of Vehicle Accident in Changsha of China. A statistic measurement of the fatality and serious injury risks with respect to impact speed was carried out by logistic regression analysis. Secondly, 12 pedestrian and 12 bicyclist accidents were further selected for reconstruction with MADYMO program. A comparative analysis was conducted based on the results from accident analysis and computer reconstructions for the injury risk, head impact conditions and dynamic response of pedestrians and bicyclists. The results indicate that bicyclists suffered lower risks of severe injuries and fatalities compared with pedestrians. The risks of AIS 3+ injury and fatality are 50% for pedestrians at impact speeds of 53.2 km/h and 63.3 km/h, respectively, while that for bicyclists at 62.5 km/h and 71.1 km/h, respectively. The findings could have a contribution to get a better understanding of pedestrians" and bicyclists" exposures in urban traffic in China, and provide background knowledge to generate strategies for pedestrian protection.
The paper aims to study the injury risk and kinematics of pedestrians involved in different passenger vehicle collisions. Furthermore, the difference of pedestrian kinematics in the accidents involved minivan and sedan was analyzed. The 18 sample cases of passenger car to pedestrian collisions were selected from the database of In-depth Investigation of Vehicle Accident in Changsha of China (IVAC),of which the 12 pedestrian accidents involved in a minivan impact for each case, and the 6 accidents in a sedan impact for each. The selected cases were reconstructed by using mathematical models of pedestrians and accident vehicles in a multi-body dynamic code MADYMO environment. The logistic regression models of the risks for pedestrian AIS 3+ injuries and fatalities were developed in terms of vehicle impact speed by analyzing the minivan-pedestrian and sedan-pedestrian accidents. The difference of pedestrian kinematics was identified by comparing the results from reconstructed pedestrian accidents between the minivans and sedans collisions. The result shows that there is a significant correlation among the impact speed and the severity of pedestrian injuries. The minivan poses greater risk to pedestrian than sedan at the same impact speed. The kinematics of pedestrian was greatly influenced by vehicle front shape.
For more than a decade, ADAC accident researchers have analysed road accidents with severe injuries, recording some 20,000 accidents. An important task in accident research is to determine the causative factors of road accidents. Apart from vehicle engineering and human factors, accident research also focuses on infrastructural and environmental aspects. To find out what accident scenarios are the most common in ADAC accident research and what driver assistance systems can prevent them, our first task was to conduct a detailed accident analysis. Using CarMaker, we performed a realistic simulation of accident scenarios, including crashes, with varying parameters. To begin with, we made an initial selection of driver assistance systems in order to determine those with the greatest accident prevention potential. One important finding of this study is that the safety potential of the individual driver assistance systems can actually be examined. It also turned out that active safety offers even much more potential for development and innovation than passive safety. At the same time, testing becomes more demanding, too, as new systems keep entering the market, many of them differing in functional details. ADAC will continue to test all driver assistance systems as realistically as possible so as to be able to provide advice to car buyers. Therefore, it will be essential to develop and improve test conditions and criteria.
Airbag-Systeme können, wie frühere Untersuchungen gezeigt haben, die passive Sicherheit von Motorrädern wirksam verbessern. Der vorliegende Forschungsbericht betrachtet die Übertragbarkeit von Pkw-Airbag-Konzepten auf das Motorrad und befasst sich vor allem mit dem Problem der motorradgerechten und sicheren Auslösung des Airbags. Die Funktion des Motorradairbags unterscheidet sich von der des Pkw-Airbags in entscheidender Weise durch die Möglichkeit, die Flugbahn des Fahrers bei einem Zusammenstoß mit einem rechtwinklig vor dem Motorrad befindlichen Pkw so zu beeinflussen, dass dieser das Hindernis ohne einen harten Anprall überfliegen kann. Der Abbau der kinetischen Energie des Fahrers geschieht so nicht in der kurzen Knautschzone vor dem Kollisionsobjekt, sondern in der meist ausreichend langen Auslaufzone dahinter. Der Motorradairbag kann am vorderen Tankbereich angebracht sein. Fülltechnik und Gewebematerial können vom Pkw direkt übernommen werden; jedoch ist die Nahtführung zu verstärken, da der Motorradairbag vorwiegend auf Scherung beansprucht wird. Gravierende Unterschiede ergeben sich in der Sensierung eines Crashs, da durch das an der Telegabel geführte Vorderrad signifikante Verzögerungsanstiege des Motorrades erst sehr spät erfolgen. Es ist daher nicht möglich, wie beim Pkw den Airbag allein über Beschleunigungsaufnehmer zu zünden. Schwerpunkt des Berichtes sind daher verschiedene Vorschläge, bei heute üblichen Motorradkonstruktionen einen Crash für eine Airbagauslösung rechtzeitig und sicher sensieren zu können. Zu charakteristischen Unfall-Ereignissen werden Sensoren nach verschiedenen Wirkprinzipien geordnet vorgestellt. Nach einer technischen Bewertung erweisen sich zwei Sensorvarianten als geeignet für eine zuverlässige Zündung des Airbag; gleichzeitig kann mit einer logischen Verknüpfung ihrer Signale eine Fehlauslösung sicher vermieden werden. Die ausgewählten und näher beschriebenen Sensoren registrieren den Druckanstieg im Vorderradreifen und die plastische Verformung der Telegabel. Damit ist eine Sensierung des Aufpralls rechtzeitig möglich. Je nach Größe und Dauer der Verzögerung kann der Druck des Luftkissens verändert werden, so dass der Motorradairbag in Abhängigkeit der Fahrgeschwindigkeit nur aufpralldämpfend oder flugbahnbeeinflussend wirkt. Testprogramme zur weiteren Entwicklung von Airbagsensoren für Motorräder werden als Forschungsbedarf näher erläutert.
It is commonly agreed that active safety will have a significant impact on reducing accident figures for pedestrians and probably also bicyclists. However, chances and limitations for active safety systems have only been derived based on accident data and the current state of the art, based on proprietary simulation models. The objective of this article is to investigate these chances and limitations by developing an open simulation model. This article introduces a simulation model, incorporating accident kinematics, driving dynamics, driver reaction times, pedestrian dynamics, performance parameters of different autonomous emergency braking (AEB) generations, as well as legal and logical limitations. The level of detail for available pedestrian accident data is limited. Relevant variables, especially timing of the pedestrian appearance and the pedestrian's moving speed, are estimated using assumptions. The model in this article uses the fact that a pedestrian and a vehicle in an accident must have been in the same spot at the same time and defines the impact position as a relevant accident parameter, which is usually available from accident data. The calculations done within the model identify the possible timing available for braking by an AEB system as well as the possible speed reduction for different accident scenarios as well as for different system configurations. The simulation model identifies the lateral impact position of the pedestrian as a significant parameter for system performance, and the system layout is designed to brake when the accident becomes unavoidable by the vehicle driver. Scenarios with a pedestrian running from behind an obstruction are the most demanding scenarios and will very likely never be avoidable for all vehicle speeds due to physical limits. Scenarios with an unobstructed person walking will very likely be treatable for a wide speed range for next generation AEB systems.
There is a need for detecting characteristics of pedestrian movement before car-pedestrian collisions to trigger a fully reversible pedestrian protection system. For this purpose, a pedestrian sensor system has been developed. In order to evaluate the effectiveness of the sensor system, the in-depth knowledge of car-pedestrian impact scenarios is needed. This study aims at the evaluation of the sensor system. The accident data are selected from the STRADA database. The accident scenarios available in this database were evaluated and the knowledge of the most common scenarios was developed in terms of the pedestrian trajectory, the pedestrian speed, the car trajectory, the car velocity, etc. A mathematical model was then established to evaluate the sensor system with different detective angles. It was found that in order to detect all the pedestrians in the most common scenarios on time the sensor detective angle must be kept larger than 60 degrees.
The proportion of older road users is increasing because of demographic change (in the group 65+ from current 18% to about 24% by 2030). The mobility needs of people 65+ often differ from those of younger people. Seniors (65+) are already more involved in fatal accidents than younger road users. According to the age development, the senior share of road deaths in the EU of today is increasing nearly one-fifth to one-third. From the in-depth analysis of accidents generic simulation models were developed. Attention has been paid both to psycho-physical characteristics as well as on the social and physical environment and their specifics in conjunction with seniors. By simulating the defined scenarios and varying the defined relevant parameters, accident influencing factors were examined as a basis for avoidance. In addition, the parameters were varied to show the influence from the vehicle, the pedestrian and the infrastructure to avoid the accident or to characterize the conditions for which the accident is inevitable.
Straßenseitige Fahrzeug-Rückhaltesysteme haben entsprechend der Richtlinie für passiven Schutz an Straßen durch Fahrzeug-Rückhaltesysteme (RPS) die Aufgabe, die Folgen von Verkehrsunfällen so gering wie möglich zu halten. Sie kommen dabei sowohl zum Schutz unbeteiligter Personen, des Gegenverkehrs bei zweibahnigen Straßen sowie schutzbedürftiger Bereiche neben der Straße als auch zum Schutz der Fahrzeuginsassen vor schweren Folgen infolge Abkommens von der Fahrbahn zum Einsatz. Vor dem Einsatz der unterschiedlichen Systeme muss die Wirksamkeit des jeweiligen Systems für den entsprechenden Anwendungsfall nachgewiesen werden. Dabei regeln die RPS, welche Anforderungen an welchen örtlichen Gegebenheiten erfüllt sein müssen. In DIN EN 1317 sind die zugehörigen Prüfverfahren beschrieben. Da ein normiertes Prüfverfahren nicht alle real auftretenden Unfallszenarien abdecken kann, stellte sich die Frage, wie sich Stahlschutzplanken und Betonschutzwände beim großwinkligen Anprall kleiner und leichter Fahrzeuge verhalten und wie es um die Insassensicherheit bestellt ist. Eine im Rahmen des resultierenden Forschungsprojektes durchgeführte Analyse des Unfallgeschehens ergab für das Jahr 2007 die Zahl von 25.038 polizeilich registrierten Unfällen mit Anprall gegen eine Schutzeinrichtung [Statistisches Bundesamt]. Angaben zu Anprallwinkel, Kollisionsgeschwindigkeit und Fahrzeugmasse können dieser Statistik nicht entnommen werden. Für die In-depth-Analyse wurden daher 69 Unfallgutachten zu Kollisionen mit großem Anprallwinkel (≥ 25-°) aus der DEKRA-Unfalldatenbank herangezogen. Der Schwerpunkt wurde dabei auf 39 Unfälle gelegt, die sich auf Bundesautobahnen ereignet hatten. Mit zunehmendem Anprallwinkel nahm die Unfallhäufigkeit ab. Der größte Winkel lag bei 60-°. Die Masse der anprallenden Fahrzeuge lag zwischen 750 kg und 1.935 kg. Auffällig war die Häufung von Schleuderunfällen. In 29 Fällen kam es zu einem prekollisionären Schleudervorgang. Die Analyse des Unfallgeschehens hat so gezeigt, dass Anpralle gegen passive Schutzeinrichtungen auf Bundesautobahnen mit zunehmendem Anprallwinkel seltener werden und dass der in der Norm für die Systemprüfung geforderte Maximalwinkel von 20-° das Gesamtunfallgeschehen sehr gut abdeckt. Auf Basis der gewonnenen Ergebnisse erfolgte die Festlegung einer Crash-Test-Konfiguration zur Erlangung von Erkenntnissen über die Insassensicherheit bei großwinkligen Anprallen. Dabei wurde als Grundlage der Anprallversuch TB 11 verwendet, wobei der Anprallwinkel von 20-° auf 45-° erhöht wurde. Die Kollisionsgeschwindigkeit von 100 km/h sowie die Fahrzeugmasse von 900 kg blieben unverändert. Die Anpralltests erfolgten gegen eine simulierte Ortbetonwand sowie gegen eine Stahlschutzplanke vom Typ Super-Rail-®. Die Versuchsfahrzeuge waren typgleich mit den Modellen, die für die ursprüngliche TB-11-Prüfung der Systeme verwendet wurden. Die Versuche haben gezeigt, dass beide Systeme die Rückhaltung der anprallenden Fahrzeuge sicher gewährleisteten. Für die Fahrer beider Fahrzeuge hätte aber keine Überlebenschance bestanden. Über das Schutzniveau der Fahrzeuginsassen entscheiden bei derartigen Anprallkonstellationen letztendlich das Niveau der passiven Sicherheit der anprallenden Fahrzeuge sowie das Energieabsorptionsvermögen der die Fahrgastzelle umschließenden Strukturen.
Es wurden Unfälle, die im Rahmen des Forschungsprojektes "Erhebungen am Unfallort" dokumentiert wurden, hinsichtlich der Häufigkeit und der Charakteristik von Pkw-Mehrfachkollisionen analysiert. Beschrieben wurden bei einer vergleichenden Gegenüberstellung von Einfach- und Mehrfachkollisionen die Besonderheiten, die die Mehrfachkollisionen prägen, und zwar im Vorfeld des Unfallgeschehens wie auch im Unfallgeschehen selbst. Mit allen beobachteten Unterschieden der Merkmalsausprägungen ist eine Steigerung der Ausgangsgeschwindigkeit, also der Geschwindigkeit, die vor dem Unfallgeschehen gefahren wurde, verbunden. Die Entstehungswahrscheinlichkeit von Mehrfachkollisionen steigt mit der Zunahme der Fahrgeschwindigkeiten. Geschlechtsspezifische Unterschiede sind lediglich für die Wahl der Ausgangsgeschwindigkeiten vor dem Unfallereignis von Bedeutung. Keine Rolle spielen Fahrzeugeigenschaften bei der Entstehung von Mehrfachkollisionen. Bei Mehrfachkollisionen wurde häufig beobachtet, dass Pkw seitlich mit Objekten am Straßenrand (Leitplanke, Bäume etc.) zusammenstoßen. Bei Seitenkollisionen treten überdurchschnittlich schwere Fahrzeugdeformationen sowie schwere Verletzungen am Kopf, im Thoraxbereich und an den oberen Extremitäten auf. Die Rekonstruktion von Mehrfachkollisionen wird durch ein oftmals komplexes Spuren- und Deformationsbild erschwert. Hilfreich erweisen sich fotogrammetrische Verfahren wie Stereoaufnahmen und Draufsichtfotografie.
During the past five years, a Euro NCAP technical working group on pedestrian safety has been working on improving test and assessment procedures for enhanced passive pedestrian safety. After harmonizing the tools and procedures as much as possible with legislation, the work was mainly focused on the development of grid procedures for the pedestrian body regions head, upper leg with pelvis and lower leg with knee. Furthermore, the test parameters for the head and the upper leg were revised, a new lower legform impactor was introduced and the injury thresholds were adjusted or, where necessary, the injury criteria were changed. Finally, the assessment limits and colour scheme were refined, widening the range and adding two more colours in order to provide a more detailed description of the pedestrian safety performance. By abstaining from an assessment based on a worst point selection philosophy, the improved test point determination procedures that were introduced during the years 2013 and 2014 give a more homogeneous, high resolution picture of the pedestrian safety performance of the vehicle frontends. By using a uniform grid for each test zone approximately 200 test points, evenly distributed within each area, can now be assessed per vehicle. The introduction of the flexible pedestrian legform impactor in 2014 enables a more realistic injury prediction of the knee and the tibia using a biofidelic test tool. With the new upper legform test that has been launched in 2015 the assessment in that area is now focusing on the injured body region instead of the injury causing vehicle part and thus is aligned with the approach in the remaining body regions head and lower leg. At the same time, a monitoring test with the headform impactor against the bonnet leading edge is closing the possible gap between the test areas to identify injury causing vehicle parts that moved out of focus due to the introduction of the new upper legform test. The paper describes the new test and assessment procedures with their underlying philosophy and gives an outlook in terms of open issues, specifying the needs for further improvement in the future. In parallel to the work of the pedestrian subgroup, a Euro NCAP working group on heavy vehicles introduced a set of protocol changes in 2011 that were related to the assessment of M1 vehicles derived from commercial vehicles, with a gross vehicle weight between 2.5 and 3.5 tons and 8 or 9 seats. The paper also investigates the applicability of the new pedestrian test and assessment procedures to heavy vehicles.
Still correlated with high mortality rates in traffic accidents traumatic aortic ruptures were frequently detected in unprotected car occupants in the early years. This biomechanical analysis investigates the different kinds of injury mechanisms leading to traumatic aortic injuries in todays traffic accidents and how the way of traffic participation affects the frequency of those injuries over the years. Based on GIDAS reported traffic accidents from 1973 to 2014 are analyzed. Results show that traumatic aortic injuries are mainly observed in high-speed accidents with high body deceleration and direct load force to the chest. Mostly chest compression is responsible for the load direction to the cardiac vessels. The main observed load vector is from caudal-ventral and from ventral solely, but also force impact from left and right side and in roll-over events with chest compression lead to traumatic aortic injuries. Classically, the injury appeares at the junction between the well-fixed aortic arch and the pars decendens following a kind of a scoop mechanism, a few cases with a hyperflexion mechanism are also described. In our analysis the deceleration effect alone never led to an aortic rupture. Comparing the past 40 years aortic injuries shift from unprotected car occupants to today's unprotected vulnerable road users like pedestrians, cyclists and motorcyclists. Still the accident characteristics are linked with chest compression force under high speed impact, no seatbelt and direct body impact.
The presence and performance of Advanced Driver Assistance Systems (ADAS) has increased over last years. Systems available on the market address also conflicts with vulnerable road users (VRUs) such as pedestrians and cyclists. Within the European project PROSPECT (Horizon2020, funded by the EC) improved VRU ADAS systems are developed and tested. However, before determining systems" properties and starting testing, an up-to-date analysis of VRU crashes was needed in order to derive the most important Use Cases (detailed crash descriptions) the systems should address. Besides the identified Accident Scenarios (basic crash descriptions), this paper describes in short the method of deriving the Use Cases for car-to-cyclist crashes. Method Crashes involving one passenger car and one cyclist were investigated in several European crash databases looking for all injury severity levels (slight, severe and fatal). These data sources included European statistics from CARE, data on national level from Germany, Sweden and Hungary as well as detailed accident information from these three countries using GIDAS, the Volvo Cars Cyclist Accident database and Hungarian in-depth accident data, respectively. The most frequent accident scenarios were studied and Use Cases were derived considering the key aspects of these crash situations (e.g., view orientation of the cyclist and the car driver- manoeuvre intention) and thus, form an appropriate basis for the development of Test Scenarios. Results Latest information on car-to-cyclist crashes in Europe was compiled including details on the related crash configurations, driving directions, outcome in terms of injury severity, accident location, other environmental aspects and driver responsibilities. The majority of car-to-cyclist crashes occurred during daylight and in clear weather conditions. Car-to-cyclist crashes in which the vehicle was traveling straight and the cyclist is moving in line with the traffic were found to result in the greatest number of fatalities. Considering also slightly and seriously injured cyclists led to a different order of crash patterns according to the three considered European countries. Finally the paper introduced the Use Cases derived from the crash data analysis. A total of 29 Use Cases were derived considering the group of seriously or fatally injured cyclists and 35 Use Cases were derived considering the group of slightly, seriously or fatally injured cyclists. The highest ranked Use Case describes the collision between a car turning to the nearside and a cyclist riding on a bicycle lane against the usual driving direction. A unified European dataset on car-to-cyclist crash scenarios is not available as the data available in CARE is limited, hence national datasets had to be used for the study and further work will be required to extrapolate the results to a European level. Due to the large number of Use Cases, the paper shows only highest ranked ones.
Causation of traffic accidents with children from the perspective of all involved participants
(2017)
In the year 2014 about 2,800 children between zero and 14 years got injured due to traffic accidents in Austria. More than 50% were taking part in traffic as active road users like cyclists or pedestrians. Within this study 46 real world traffic accidents between vehicles and children as pedestrians were analysed. In 39 cases, car drivers hit the crossing children. In the other cases, the collision opponents were busses, trucks or motorcycles. Most of the children got hit while crossing a road at urban sites. By analysing the traffic accidents from the perspectives of all involved participants, vehicle drivers and injured children, it is possible to identify factors for each participant, which led to the accident and factors that contributed the accident. The main task is to find patterns in the behaviour of crash victims (children and driver) before the collision. One important fact is that in more than 50% of the analysed cases sight obstructions were an important contributing factor for both, the driver and the child. From drivers view situations in which the child moved unexpected into the driven road lane were often found. For the injured child, factors like: no attention to the road traffic or no sufficient traffic observation were found to be relevant. Further it- possible to sensitise children and adults to possible source of critical traffic situations according to the findings of this study.
This study aimed at comparing head Wrap Around Distance (WAD) of Vulnerable Road User (VRU) obtained from the German in-depth Accident Database (GIDAS), the China in-depth Accident Database (CIDAS) and the Japanese in-depth Accident Database (ITARDA micro). Cumulative distribution of WAD of pedestrian and cyclist were obtained for each database (AIS2+) showing that WAD of cyclists were larger than the ones of pedestrians. Comparing three regions, the 50%tile WAD of GIDAS was larger than that of both Asian accident databases. Using linear regression that might predict WAD of pedestrians and cyclists from Impact speed and VRU height, WADs were calculated to be 206cm/219cm (Pedestrian/Cyclist) for GIDAS, 170cm/192cm for CIDAS and 211cm/235cm for ITARDA. In addition, this study may be helpful for reconsideration of WAD measurement alignment between accident reconstruction and test procedures.
Ausgehend von den Unfalldaten der letzten Jahre wird die Bedeutung von Fußgängerunfällen im Unfallgeschehen dargestellt. Betrachtet man die bei Unfällen getöteten Verkehrsteilnehmer, so sind am häufigsten Personen in Kraftfahrzeugen betroffen. Am zweithäufigsten werden, gemäß der Unfallstatistik, Fußgänger getötet. Eine Möglichkeit zur Verbesserung des Schutzes von Fußgängern und anderen sogenannten "ungeschützten Verkehrsteilnehmern" im Falle einer Kollision mit einem Kraftfahrzeug sind Maßnahmen am Fahrzeug. Um die Wirksamkeit derartiger Maßnahmen zu beurteilen, wurde durch das EEVC (European Enhanced Vehicle-Safety Committee) ein Prüfverfahren entwickelt. Es handelt sich dabei um ein Komponentenprüfverfahren, mit dem die Frontstruktur von Fahrzeugen, die bei einer Kollision mit einem Fußgänger hauptsächlich betroffen ist, geprüft wird. Es werden keine den gesamten Menschen repräsentierende Dummies verwendet, stattdessen werden Prüfkörper, die einzelne Körperteile simulieren, eingesetzt. Dieser EEVC Vorschlag wird geschildert. Darüber hinaus wird über Aktivitäten außerhalb des EEVC berichtet, sowie über den aktuellen Stand der Bemühungen der Europäischen Kommission in Bezug auf den Fußgängerschutz, die derzeit, auf Grundlage des Prüfvorschlages des EEVC, einen Vorschlag für eine Europäische Richtlinie erarbeitet.
The incidence of side impacts was investigated from GIDAS data. Both vehicle-fixed object and vehicle-vehicle collisions were analysed as these are enclosed within the consumer testing program. Vehicle-fixed object collisions were stratified according to ESC availability. Results indicated that vehicles equipped with ESC rarely have pure-lateral impacts. An increase in oblique collisions was seen for the vehicles with ESC whereby most vehicle were driving in left curves. The analysis of vehicle-vehicle collisions developed injury risk curves were developed at the AIS3+ injury severity for the vehicle-vehicle side impacts. Results suggested that greatest injury risk occurred when a Pre Euro NCAP vehicle was struck by a Post Euro-NCAP vehicle. The remaining curves did not show different behaviour, indicating that stiffness increased have been equally combated. This was attributable to the few Post Euro-NCAP vehicles that had a deployed curtain airbag available in the sample. The integration of Euro NCAP testing has shown to improve vehicle crashworthiness for pole collisions, as those vehicles with ESC rarely incur lateral impacts.
In der amtlichen Statistik der Unfälle wird zwischen "Abkommen von der Fahrbahn nach links" und "Abkommen nach rechts" unterschieden. Jene Unfälle sind nicht erfasst, bei denen es zunächst auf der Fahrbahn zu einem leichten Zusammenstoß kommt, infolge dessen ein Auto von der Fahrbahn abkommt, wobei unter Umständen schwere Unfallfolgen entstehen. Im Jahre 1984 wurden unter Unfallart "Abkommen" 2.092 Getötete = 28,5 % aller im Straßenverkehr 1984 Getöteten ausgewiesen. Die Verteilung der Unfälle auf Innerortsstraßen, Landstraßen und Autobahnen wird angegeben. Die Unfallschwere beim Abkommen nach rechts ist bedeutend größer als beim Abkommen nach links. Mehr als 80 % der abkommenden Fahrzeuge verlassen die Fahrbahn unter 20 Grad. Die größere Unfallschwere beim Abkommen nach rechts wird auf Fehlen von Schutzplanken zurückgeführt. Der günstige Einfluss von Randmarkierungen wird nicht erwähnt. An der Zahl schwerer Unfallfolgen haben Bäume an Landstraßen einen 50 %-Anteil. Sie sollten 5 m, in Außenkurven 10 m vom Fahrbahnrand entfernt sein, andernfalls durch Buschgruppen ersetzt oder durch Schutzplanken geschützt werden. Würde man durch wirksame Maßnahmen die Unfälle durch Abkommen nach rechts auf die Zahl der Unfälle durch Abkommen nach links reduzieren, würden sich die volkswirtschaftlichen Kosten um rund. 3 Mrd. DM jährlich vermindern.
The goal of the project FIMCAR (Frontal Impact and Compatibility Assessment Research) was to define an integrated set of test procedures and associated metrics to assess a vehicle's frontal impact protection, which includes self- and partner-protection. For the development of the set, two different full-width tests (full-width deformable barrier [FWDB] test, full-width rigid barrier test) and three different offset tests (offset deformable barrier [ODB] test, progressive deformable barrier [PDB] test, moveable deformable barrier with the PDB barrier face [MPDB] test) have been investigated. Different compatibility assessment procedures were analysed and metrics for assessing structural interaction (structural alignment, vertical and horizontal load spreading) as well as several promising metrics for the PDB/MPDB barrier were developed. The final assessment approach consists of a combination of the most suitable full-width and offset tests. For the full-width test (FWDB), a metric was developed to address structural alignment based on load cell wall information in the first 40 ms of the test. For the offset test (ODB), the existing ECE R94 was chosen. Within the paper, an overview of the final assessment approach for the frontal impact test procedures and their development is given.
EEVC Status report
(2001)
Seit 1997 gibt es in Europa unter dem Namen Euro NCAP (European New Car Assessment Programme) einheitliche Test- und Ratingverfahren. Sie liefern Informationen über den Insassen- und über den Fußgängerschutz. Euro NCAP hat seither fast 90 Fahrzeugmodelle in jeweils drei unterschiedlichen Crashtest-Konfigurationen untersucht und die Ergebnisse den europäischen Konsumenten zugänglich gemacht. Im Beitrag wird auf die Testbedingungen, die Euro NCAP-Ratingverfahren sowie auf die Weiterentwicklung von Euro NCAP eingegangen. Ein wichtiger Aspekt wird dabei auch die weltweite Harmonisierung der Test- und Ratingverfahren sein.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.