Filtern
Erscheinungsjahr
- 2015 (124) (entfernen)
Dokumenttyp
- Buch (Monographie) (62)
- Konferenzveröffentlichung (56)
- Wissenschaftlicher Artikel (2)
- Bericht (2)
- Arbeitspapier (2)
Schlagworte
- Germany (104)
- Deutschland (101)
- Research report (56)
- Forschungsbericht (55)
- Conference (41)
- Konferenz (41)
- Test (31)
- Versuch (29)
- Unfall (24)
- Accident (22)
Im Rahmen der wissenschaftlichen Begleitung zum deutschlandweiten Feldversuch mit Lang-Lkw ist auch eine Untersuchung zu den Sicherheitsauswirkungen im Zusammenhang mit Überholvorgängen gegenüber Lang-Lkw sowie deren Räumvorgängen an Knotenpunkten durchgeführt worden. Wegen der geringen Anzahl an diesem Feldversuch teilnehmender Lang-Lkw, vor allem aber auch wegen des vorrangigen BAB-Einsatzes von Lang-Lkw und daher fehlender nennenswerter Streckenabschnitte auf Landstraßen, werden im Rahmen des FE-Vorhabens ausschließlich Messungen bzw. Beobachtungen durchgeführt, die vom Lang-Lkw selbst ausgehen. Mit ihnen wird das Annäherungs-, Ausscher-, Vorbeifahrt- und Einscherverhalten bei Überholvorgängen gegenüber Lang-Lkw auf Landstraßen und Autobahnen erfasst. Aus den Analysen von über 200 Überholungen gegenüber Lang-Lkw bzw. Vergleichsfahrzeugen lassen sich keine Indizien für ein erhöhtes Risiko beim Überholen von Lang-Lkw erkennen. Tendenziell nehmen die geringsten Sicherheitsabstände in ausreichendem Maße zu, die Beschleunigungen bei kritischen Geschwindigkeiten liegen leicht höher. Ansatzpunkte für eine Erhöhung der Sicherheitsrisiken sind auch beim Räumen von Lang-Lkw nicht zu erkennen. Generell ist eine geringere Geschwindigkeit der betrachteten Lang-Lkw und damit eine theoretisch sicherheitsfördernd größere Geschwindigkeitsdifferenz zwischen Überholer und Überholtem zu beobachten. Allerdings würde eine systematisch niedrigere Geschwindigkeit von Lang-Lkw vor allem auf Autobahnen vermutlich zu einer höheren Anzahl an Überholungen durch andere Lkw führen. Auch für den im Dauerbetrieb zu erwartenden Fall gleicher Geschwindigkeiten gibt es keinen Anhaltspunkt, dass erhöhte Sicherheitsrisiken zu erwarten sind: Bei allen Parametern liegen die Werte bei kritischen Überholvorgängen bei Lang-Lkw etwas günstiger als bei den Vergleichsfahrzeugen, so dass die theoretisch wegen der größeren Fahrzeuglänge zu erwartenden Erhöhungen des Risikos mindestens kompensiert würden.
Assessment of the effectiveness of Intersection Assistance Systems at urban and rural accident sites
(2015)
An Intersection Collision Avoidance System is a promising safety system for accident avoidance or injury mitigation at junctions. However, there is still a lack of evidence of the effectiveness, due to the missing real accident data concerning Advanced Driver Assistance Systems. The objective of this study is the assessment of the effectiveness of an Intersection Collision Avoidance System based on real accidents. The method used is called virtual pre-crash simulation. Accidents at junctions were reconstructed by using the numerical simulation software PC-Crashâ„¢. This first simulation is called the baseline simulation. In a second step the vehicles of these accidents were equipped with an Intersection Collision Avoidance System and simulated again. The second simulation is called the system simulation. In the system simulation two different sensors and four different intervention strategies were used, based on a time-to-collision approach. The effectiveness of Intersection Collision Avoidance System has been evaluated by using an assessment function. On average 9% of the reviewed junction accidents could have been avoided within the system simulations. The other simulation results clearly showed a change in the principal direction of force, delta-v and reduction of the injury severity.
Bereits vor rund zwanzig Jahren wurde die Entwicklung einer bundeslandübergreifenden Erhaltungsstrategie für Verkehrsflächen und Ingenieurbauwerke auf Netzebene angegangen. Zwischenzeitlich sind hierfür Erfassungs- und Bewertungsverfahren erarbeitet worden und in Betrieb. Aufbauend auf den guten Erfahrungen, die mit den bestehenden Managementsystemen gemacht wurden, erscheint es somit folgerichtig für die bislang vernachlässigten sonstigen Anlagenteile der Straße ein eigenständiges Asset Management zu entwickeln. Um die hierfür notwendige Datengrundlage zu schaffen, wurde in dem vorliegenden Forschungsprojekt mittels Literaturrecherche und bundesweiter Befragung von Verantwortlichen Erhaltungskostensätze, Nutzungsdauern sowie Ausstattungsquoten für die sonstigen Anlagenteile " beispielsweise Lichtsignalanlagen oder Schutzeinrichtungen " erhoben. Die Ergebnisse der Umfrage fußten in der Festlegung von für ein Asset Management relevanten sonstigen Anlagenteile sowie einer Untergliederung dieser in einzelne Aggregate. An den jeweiligen Anlagenteilen/Aggregaten konnten dann Leistungen der Instandhaltung, Instandsetzung und Erneuerung definiert werden, die in Kombination mit den Nutzungsdauern und den Ausstattungsquoten eine Kalkulation der benötigten finanziellen Aufwendungen für die Erhaltung der sonstigen Anlagenteile ermöglichen. Weiterer Forschungsbedarf besteht von allem bei der Verbesserung und Verdichtung der Datengrundlage sowie die Umsetzung in einem Computer-Programm nach dem Prinzip des PMS und BMS.
Since the beginning of the testing activities related to passive pedestrian safety, the width of the test area being assessed regarding its protection level for the lower extremities of vulnerable road users has been determined by geometrical measurements at the outer contour of the vehicle. During the past years, the trend of a decreased width of the lower extremity test and assessment area realized by special features of the outer vehicle frontend design could be observed. This study discusses different possibilities for counteracting this development and thus finding a robust definition for this area including all structures with high injury risk for the lower extremities of vulnerable road users in the event of a collision with a motor vehicle. While Euro NCAP is addressing the described problem by defining a test area under consideration of the stiff structures underneath the bumper fascia, a detailed study was carried out on behalf of the European Commission, aiming at a robust, worldwide harmonized definition of the bumper test area for legislation, taking into account the specific requirements of different certification procedures of the contracting parties of the UN/ECE agreements from 1958 and 1998. This paper details the work undertaken by BASt, also serving as a contribution to the TF-BTA of the UN/ECE GRSP, towards a harmonized test area in order to better protect the lower extremities of vulnerable road users. The German In-Depth Accident Database GIDAS is studied with respect to the potential benefit of a revised test area. Several practical options are discussed and applied to actual vehicles, investigating the differences and possible effects. Tests are carried out and the results studied in detail. Finally, a proposal for a feasible definition is given and a suggestion is made for solving possible open issues at angled surfaces due to rotation of the impactor. The study shows that, in principle, there is a need for the entire vehicle width being assessed with regard to the protection potential for lower extremities of vulnerable road users. It gives evidence on the necessity for a robust definition of the lower extremity test area including stiff and thus injurious structures at the vehicle frontend, especially underneath the bumper fascia. The legal definition of the lower extremity test area will shortly be almost harmonized with the robust Euro NCAP requirements, as already endorsed by GRSP, taking into account injurious structures and thus contributing to the enhanced protection of vulnerable road users. After finalization of the development of a torso mass for the flexible pedestrian legform impactor (FlexPLI) it is recommended to consider again the additional benefit of assessing the entire vehicle width.
During the past five years, a Euro NCAP technical working group on pedestrian safety has been working on improving test and assessment procedures for enhanced passive pedestrian safety. After harmonizing the tools and procedures as much as possible with legislation, the work was mainly focused on the development of grid procedures for the pedestrian body regions head, upper leg with pelvis and lower leg with knee. Furthermore, the test parameters for the head and the upper leg were revised, a new lower legform impactor was introduced and the injury thresholds were adjusted or, where necessary, the injury criteria were changed. Finally, the assessment limits and colour scheme were refined, widening the range and adding two more colours in order to provide a more detailed description of the pedestrian safety performance. By abstaining from an assessment based on a worst point selection philosophy, the improved test point determination procedures that were introduced during the years 2013 and 2014 give a more homogeneous, high resolution picture of the pedestrian safety performance of the vehicle frontends. By using a uniform grid for each test zone approximately 200 test points, evenly distributed within each area, can now be assessed per vehicle. The introduction of the flexible pedestrian legform impactor in 2014 enables a more realistic injury prediction of the knee and the tibia using a biofidelic test tool. With the new upper legform test that has been launched in 2015 the assessment in that area is now focusing on the injured body region instead of the injury causing vehicle part and thus is aligned with the approach in the remaining body regions head and lower leg. At the same time, a monitoring test with the headform impactor against the bonnet leading edge is closing the possible gap between the test areas to identify injury causing vehicle parts that moved out of focus due to the introduction of the new upper legform test. The paper describes the new test and assessment procedures with their underlying philosophy and gives an outlook in terms of open issues, specifying the needs for further improvement in the future. In parallel to the work of the pedestrian subgroup, a Euro NCAP working group on heavy vehicles introduced a set of protocol changes in 2011 that were related to the assessment of M1 vehicles derived from commercial vehicles, with a gross vehicle weight between 2.5 and 3.5 tons and 8 or 9 seats. The paper also investigates the applicability of the new pedestrian test and assessment procedures to heavy vehicles.
Although the annual traffic accident statistics published by the national police is available in public, the detailed traffic accident data has not been released in Korea. Recently the Ministry of Land, Infrastructure and Transport recognized the importance of in-depth accident data to enhance road traffic safety and initiated a research project to establish a collection of the detailed accident data. The main objective of the project is a feasibility study to establish KIDAS (Korea In-Depth Accident Study). Within this project, three university hospitals which are located in mid-size cities have been selected to collect accident data. Annually, more than 500 cases of accidents have been collected from the in-patient's interviews and diagnosis. Unlike GIDAS (German In-Depth Accident Study), currently on-site investigation can"t be performed by the Korean police. The only available data is patient medical records, patient's description of accident circumstances and the damaged vehicle. Occasionally the police provide the accident investigation reports containing very brief information on accident causation and vehicle safety. In a first step, the concept of KIDAS is to adopt the format of iGLAD (Initiative for the Global Harmonization of Accident Data) for harmonization. Since the currently collected accident information is extremely limited compared with GIDAS, the other sources of data and calculations such as KNCAP vehicle data, pc-crash simulations, vehicle registration information, insurance company data are utilized to complete the iGLAD template. Results from KIDAS_iGLAD and the cases of assessment of active safety devices such as AEBS, ESC, and LDWS will be evaluated.
Mit Fokus auf Nordrhein-Westfalen (NRW) wird das urbane NO2-Problem umrissen. Um die Jahresgrenzwerte einzuhalten, sind beispielsweise in allen Straßenschluchten in NRW Reduktionen nötig. Die Europäische Kommission hat gegen mehrere Mitgliedsstaaten, darunter Deutschland, Vertragsverletzungsverfahren wegen der Überschreitung von NO2-Grenzwerten eröffnet. Dargestellt werden die Langzeittrends bezüglich der gemessenen Abnahme bei der Stickoxidbelastung. Potenzielle Maßnahmen können hinsichtlich ihrer möglichen Wirkungen durch den Einsatz von Modellen abgeschätzt werden, zum Beispiel Umweltzonen, Fahrverbote, Elektrofahrzeuge. Die Ergebnisse der Messungen und Modellrechnungen werden dargestellt und kritisch beleuchtet. Als Fazit ergibt sich, dass das urbane NO2-Problem nicht einfach zu lösen ist, Minderungen der NOx-Emissionen spiegeln sich nicht in der gleichen Größenordnung in der Abnahme der NO2-Belastung wieder. Bei zusätzlich wirksamen Maßnahmen wie beispielsweise einem höheren Anteil von Elektrofahrzeugen fehlt die (schnelle) praktische Umsetzbarkeit. Eine Kombination aus lokalen, regionalen und europaweiten Maßnahmen ist nötig, um das Problem zu lösen.
The EVERSAFE project addressed many safety issues for electric vehicles including the crash and post-crash safety. The project reviewed the market shares of full electric and hybrid vehicles, latest road traffic accident data involving severely damaged electric vehicles in Europe, and identified critical scenarios that may be particular for electric vehicles. Also, recent results from international research on the safety of electric vehicles were included in this paper such as results from performed experimental abuse cell and vehicle crash tests (incl. non-standardized tests with the Mitsubishi i-MiEV and the BMW i3), from discussions in the UN IG REESS and the GTR EVS as well as guidelines (handling procedures) for fire brigades from Germany, Sweden and the United States of America. Potential hazards that might arise from damaged electric vehicles after severe traffic accidents are an emerging issue for modern vehicles and were summarized from the perspective of different national approaches and discussed from the practical view of fire fighters. Recent rescue guidelines were reviewed and used as the basis for a newly developed rescue procedure. The paper gives recommendations in particular towards fire fighters, but also to vehicle manufacturers and first-aiders.
Zur Ermittlung einer Mehr- oder Minderbeanspruchung des Straßenoberbaus durch Lang-Lkw wurde eine Stichprobe von 1.746 Fahrten im Direktverkehr und 483 Fahrten im kombinierten Verkehr analysiert. Die durchschnittliche Fahrzeuggesamtmasse der Lang-Lkw betrug 32,3 t. Ca. 9 % der Lang-Lkw fuhren überladen. Das Niveau der Überladungen lag jeweils unterhalb 3 t. Die maximale Achslast betrug 11,7 t. Die Achslastverteilung von Lang-Lkw im kombinierten Verkehr weist ein niedrigeres Niveau als für Lang-Lkw im Direktverkehr auf. Im Vergleich zu äquivalenten konventionellen Lkw ergibt sich für Lang-Lkw eine um 5 % niedrigere Anzahl äquivalenter 10-t-Achsen. Der mittlere Achszahlfaktor fA von Lang-Lkw beträgt 7,40. Das Transportvolumen eines Lang-Lkw entspricht rechnerisch dem Transportvolumen von 1,53 äquivalenten konventionellen Lkw. Mit zunehmendem Anteil Lang-Lkw am Gesamtkollektiv Schwerverkehr (bis zu 9 %) ist eine zunehmende, vergleichsweise geringe Reduzierung der B-Zahl nach RStO 12 zu verzeichnen, was in der Regel jedoch nicht zu einem Wechsel in die nächstkleinere Belastungsklasse führen würde. Mittels Dimensionierung nach RDO Asphalt 09 errechnet sich bei Einsatz von Lang-Lkw nach dem Ende einer 30-jährigen Nutzungsdauer der Straßenbefestigung ein geringfügig niedrigerer Ermüdungsstatus, der zu einer marginalen Verlängerung des Nutzungszeitraums führen würde. Der Einsatz von Lang-Lkw würde unter Einhaltung der im Feldversuch definierten fahrzeugtechnischen Vorgaben und zulässigen Grenzwerte für Fahrzeuggesamtgewichte und Achslasten nicht zur Mehrbeanspruchung des Oberbaus von Straßen führen. Die rechnerisch festgestellte Minderbeanspruchung des Oberbaus im Vergleich zu konventionellen Lkw hat nur marginale Bedeutung und würde sich somit in der Praxis kaum spürbar auf die Nutzungsdauer der Straßen auswirken.
This study aimed at prediction of long bone fractures and assessment of lower extremity injury mechanisms in real world passenger car to pedestrian collision. For this purpose, two pedestrian accident cases with detail recorded lower limb injuries were reconstructed via combining MBS (Multi-body system) and FE (Finite element) methods. The code of PC Crash was used to determine the boundary conditions before collision, and then MBS models were used to reproduce the pedestrian kinematics and injuries during crash. Furthermore, a validated lower limb FE model was chosen to conduct reconstruction of injuries and prediction of long bone fracture via physical parameters of von Mises stress and bending moment. The injury outcomes from simulations were compared with hospital recorded injury data and the same long bone fracture patterns and positions can be observed. Moreover, the calculated long bone fracture tolerance corresponded to the outcome from cadaver tests. The result shows that FE model is capable to reproduce the dynamic injury process and is an effective tool to predict the risk of long bone fractures.