Filtern
Erscheinungsjahr
- 2013 (11) (entfernen)
Dokumenttyp
Schlagworte
- Active safety system (11) (entfernen)
Institut
- Sonstige (6)
- Abteilung Fahrzeugtechnik (4)
- Präsident (1)
It is commonly agreed that active safety will have a significant impact on reducing accident figures for pedestrians and probably also bicyclists. However, chances and limitations for active safety systems have only been derived based on accident data and the current state of the art, based on proprietary simulation models. The objective of this article is to investigate these chances and limitations by developing an open simulation model. This article introduces a simulation model, incorporating accident kinematics, driving dynamics, driver reaction times, pedestrian dynamics, performance parameters of different autonomous emergency braking (AEB) generations, as well as legal and logical limitations. The level of detail for available pedestrian accident data is limited. Relevant variables, especially timing of the pedestrian appearance and the pedestrian's moving speed, are estimated using assumptions. The model in this article uses the fact that a pedestrian and a vehicle in an accident must have been in the same spot at the same time and defines the impact position as a relevant accident parameter, which is usually available from accident data. The calculations done within the model identify the possible timing available for braking by an AEB system as well as the possible speed reduction for different accident scenarios as well as for different system configurations. The simulation model identifies the lateral impact position of the pedestrian as a significant parameter for system performance, and the system layout is designed to brake when the accident becomes unavoidable by the vehicle driver. Scenarios with a pedestrian running from behind an obstruction are the most demanding scenarios and will very likely never be avoidable for all vehicle speeds due to physical limits. Scenarios with an unobstructed person walking will very likely be treatable for a wide speed range for next generation AEB systems.
Since integrated safety systems combine active and passive safety elements in one safety system, it is necessary to define new procedures to evaluate vehicle safety from the overall system point of view. The main goal of the ASSESS project is to develop harmonized and standardized assessment procedures for collision mitigation and avoidance systems. Methods and Data Sources: In ASSESS, procedures are developed for: driver behaviour evaluation, pre-crash system performance evaluation, crash performance evaluation, socio-economic assessment. This paper will concentrate on the activities related to the crash evaluation. The objective is to perform simulations, sled tests and crash tests in order tounderstand the influence of the activation of the pre-crash systems on the occupants" injuries during the crash phase. When a traffic accident is unavoidable, pre-crash systems work on various safety devices in order to improve the vehicle occupants" protection. Braking assistance and adaptive restraint systems are the main pre-crash systems whose effect on the occupants" protection will be described in this paper. Results: The results will be a description of the effect of the activation of the pre-crash systems on the crash phase. Additionally, a set of recommendations for future methodology developments will be delivered. Furthermore, a first approach to the study of the effect of the pre-crash systems activation on the occupants" protection when the impact is unavoidable will be presented. This effect will be quantified using the biomechanical values obtained from the simulation and testing activities and their related injury risks. Simulation and testing activities will consider the following scenarios: - No activation of any pre-crash system, - Activation of one or a combination of several pre-crash systems. In this way, differences in the results obtained from different scenarios will show the effect of each pre-crash system separately during the crash phase. Discussion and Limitations: The set of activities developed in this research project is limited by the fact that with the given resources only a limited number of vehicle models could be investigated. In addition, there are also limitations related to the injury risk curves and the passive safety tools currently on the market. Conclusion and Relevance to session submitted: The paper will present a complete analysis of the effect of pre-crash systems during the crash phase when the impact is unavoidable. Details, limitations and first application experience based on a few examples will be discussed. Currently, there is not any regulation, assessment program, or other similar official procedure able to assess pre-crash systems during the crash phase. This project comprises phases of traffic accidents which have been historically analysed separately, and aims to evaluate them taking into account their interrelationship. ASSESS is one of the first European projects which deals in depth with the concept of integrated safety, defining methodologies to analyse vehicle safety from a global point of view.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
Aktive Systeme der passiven Fahrzeugsicherheit zum Fußgängerschutz, sogenannte crash-aktive Fußgängerschutzsysteme, werden seit 2005 zur Erfüllung der gesetzlichen Anforderungen (siehe Verordnung (EG) Nr. 78/2009 und 631/2009) in Serienfahrzeugen eingesetzt. Diese crash-aktiven Fußgängerschutzsysteme stellen im Gegensatz zu den rein passiven Systemen nur eine instationäre Lösung dar. Da die innerhalb der gesetzlichen Anforderungen definierten Testverfahren zur Bewertung stationärer Systeme entwickelt wurden, können derzeit mögliche Risiken instationärer Systeme nicht berücksichtigt werden. Im Rahmen dieses Forschungsprojektes soll ein Bewertungsverfahren für diese crash-aktiven Fußgängerschutzsysteme entwickelt werden, welches das reale Potential dieser Systeme möglichst gut wiedergibt. Basis hierfür soll eine umfangreiche Untersuchung zusätzlicher Risiken bilden. Die hier untersuchten instationären Schutzmaßnahmen werden nur im Falle eines Fahrzeuganpralls gegen Fußgänger aktiviert, der daher zuverlässig erkannt werden muss. Für die hierfür eingesetzten, kontaktbasierten Sensorsysteme stellen Fußgänger mit geringen Lasteinträgen in die Fahrzeugfront eine große Herausforderung dar. Die Lasteinträge hängen von zahlreichen Faktoren, wie bspw. der Höhe der entsprechenden Krafteinleitungspfade sowie der Größe und dem Gewichts des Fußgängers, ab. Mit Hilfe von umfangreichen Anprallversuchen und -simulationen wird gezeigt, dass die bisher eingesetzten Prüfkörper nur zum Teil für die Erfüllung dieser Anforderungen geeignet sind. Für ein geeignetes Prüfverfahren müssen daher neue Prüfkörper entwickelt werden. Durch die Aktivierung der Schutzmaßnahme soll bei den crash-aktiven Systemen vor allem das Verletzungsrisiko beim Kopfanprall verringert werden. Hierfür wird häufig die hintere Motorhaubenkante angehoben, um zusätzlichen Deformationsfreiraum zur Verfügung zu stellen. Die Haubenanhebung kann jedoch auch in zusätzlichen Verletzungsrisiken resultieren, bspw. durch die exponierte hintere Haubenkante oder die Verringerung des Deformationsfreiraums in Folge des Oberkörperanpralls. Ein Ersatzprüfverfahren zur Bewertung der Haubendeformation mit Hilfe des Hüftimpaktors wird vorgestellt. Ein hybrides Testverfahren bestehend aus Simulation und Versuch eignet sich für eine objektive Bewertung dieser Systeme, wobei die entsprechenden Versuchsparameter mit Hilfe der vorherigen Simulation bestimmt werden können.
There is a need to continue to set the right vehicle safety policy priorities in the future. Research has to point out the most cost efficient and safety relevant measures to further reduce the number of road traffic casualties. The overall development shows that the constant and rapid decrease in the number of road casualties slows down. New innovations need to enter the vehicle market soon, in order to continue the success achieved in the last decade. Priorities for vehicle safety are driven by safety and mobility demands. It is necessary to keep a strong lid on all aspects of elderly and vulnerable road users. The fraction of powered-two-wheelers (PTW) is a priority group. PTWs have a risk of being involved in an accident, 14times higher than that of a passenger car. However, the figures do also show that every second fatality is a car occupant. Therefore passenger car safety remains to be top priority. Heavy goods vehicles are overly represented in fatal accidents, addressing the need to make these vehicles more compatible with other road users. These facts highlight the necessity not only to increase vehicles" self protection, but also to make cars - and trucks - more compatible and safe. Cycling is a strongly increasing mode of transport. This is a further reason to demand better protection for cyclists and pedestrians from car design and car active and integrated safety systems. Another priority for future vehicle safety is related to demographics. It is less known that the purely demographic effect will be superimposed by an increasing wish of elderly people to be mobile. However, elderly people show deficits concerning their biomechanics. This emphasizes the need for better and more adaptive restraint systems, but also further technological challenges and demands for active safety systems. However, in order to progress, current technological limitations have to be overcome. Cost benefit considerations, but also consumer acceptance and desires, will drive this process.
Accident research 2.0: New methods for representative evaluation of integral safety in traffic
(2013)
BMW has developed a procedure for rating Advanced Driver Assistance Systems (ADAS) benefits that integrates two distinct tools. The tool "S.A.F.E.R." is designed to analyze the pre-crash phase. The aim of S.A.F.E.R. is to simulate all relevant processes in sufficient detail to obtain reproducible estimates of key indicators (effectiveness, false positives, etc.). The relevant processes include not only traffic and vehicle dynamics, but also environmental and most importantly human factors. Representative distributions of factors and parameters are obtained by taking the stochastic variation of all relevant parameters into account in the simulations. The second tool, known as "ICOS", has been designed to provide a high-resolution, high-fidelity description of crash phase dynamics. If one converts the outputs of stochastic simulation into inputs for crash dynamics, the result is a comprehensive description of exactly how a safety system can reduce injuries. Applications currently focus on high-fidelity simulation of individual crashes in order to enhance our understanding and optimization of connected safety systems. An integrated simulation process thus allows an exact prediction of the effectiveness in individual cases in terms of injury severity. The development and rating of integral safety need to reflect the true efficiency in the field. The integrated approach described here could provide a valid and reproducible basis for rating connected systems of active and passive safety. In particular, "virtual experiments" using a traffic-based approach and incorporating models of all relevant processes constitute an essential element of the approach.
The presentation deals with the simulation tool rateEFFECT which intends to answer the following questions: Which active safety systems should be developed to maximize safety benefit in real traffic accidents? What is the effectiveness of a specific active safety system in the real world? How many casualties could be avoided by such a system? It is shown that a lot of information is required to simulate existing accidents in order to estimate ADAS effects. This particularly includes numerical values for the pre-crash and in-crash phase. The database GIDAS provides a required minimum number of these parameters for a statistically significant sample.
The sequence of accident events can be classified by three essential phases, the pre-crash-sequence, the crash-sequence and the post-crash-sequence. The level of reliability of the information in the GIDAS-database (German In Depth Accident Study) is provided predominantly on the passive side. The period to evaluate active safety systems begins already in the pre-crash-sequence. The assessment of the potential of sensor- or communication-based active safety systems can only be accomplished by a detailed analysis of the pre-crash-phase. Hence the necessity to analyze the early period of the accident event in detail arises. This is possible with the help of the digital sketches of the accident site and the simulation of the accident by a simulation method of the VUFO GmbH. After simulating the pre-crash scenario it is possible to generate additional and standardized data to describe the pre-crash-sequences of an accident in a very high detail. These data are documented in a second database called the GIDAS Pre-Crash-Matrix (PCM). The PCM contains various tables with all relevant data to reproduce the pre-crash-sequence of traffic accidents from the GIDAS database until 5 seconds before the first collision. This includes parameters to describe the environment data, participant data and motion or dynamic data. This paper explains the creation of the PCM, the simulation itself and the contents and structure of the PCM. With this information of the pre-crash-sequence for various accident scenarios an improved benefit estimation and development of active safety systems can be made possible.
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.