Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (26) (entfernen)
Schlagworte
- Messung (26) (entfernen)
The Netherlands is on the way to change its existing skid resistance measuring method for its highway network from the Dutch RAW 72, a longitudinal force method, to the Sideway Force method. This method is described in the Technical Specification 15901-8 (SKM device) as well as 15901-6 (SCRIM device) and is in use in 9 European countries. The CEN TC 227 WG5 on Surface Characteristics is currently working on combining of these two technical Specifications into a European standard for Sideway-Force (SWF) measurement devices. The idea of this change in the Netherlands was perceived in 2013 and since then a lot of meetings have been held with the different Dutch decision makers as well as with countries which currently operate SWF devices. There was an intensive exchange of knowledge about these devices and their corresponding quality assurance systems, because the Netherlands wanted to incorporate and rely on an existing system of a neighbor country without losing their present level of quality. The Netherlands has therefore decided to incorporate the German SKM approach. The network monitoring with the new system will start in 2017. To ensure the quality of skid resistance measurements and further cooperation in this field, it has been decided to initiate an alliance between BASt and the Dutch road owner Rijkswaterstaat (RWS). This alliance will facilitate an exchange of research activities, calibration of the Dutch systems according to the existing German Standard as well as control measurements with a BASt-device on the Dutch network during the network monitoring. During 2016 also comparative measurements will be performed on a network level with the current Dutch device and with an SKM device to determine a conversion between the two and to be able to define new threshold values.
Knowledge of material properties is of great importance when developing new types of concrete and construction methods for road building, and for quality control and quality assurance. Physical material characteristics are likewise the basis for dimensioning and assessing the residual substance of concrete pavements. One relevant characteristic when examining thermally induced stress and deformation is the coefficient of thermal expansion (CTE) of concrete. This indicator, for example, significantly influences the longitudinal expansion of the pavement system as well as the degree of curling of slabs and joint movements. Extensive tests were conducted during the technical engineering assessment of the structural substance of concrete pavements in the German motorway network, including tests to determine the CTE of existing types of concrete. Because no standardised procedure currently exists in Germany for using tests to determine the CTE of concrete, the initial task was to develop a suitable test procedure from a road-building perspective, taking consideration of the national prevailing structural conditions. This article presents the results of selected status analyses, in which the CTE was determined for a total of 656 individual samples. The values calculated for the top and bottom drilled core layer are in the range 8.9 – 13.2 x 10-6/K, whereby the average CTE assumes a value of 10.7 x 10-6/K. The deviations of the CTEs from the bottom and top drilled core layer are in principle significantly below the limitation to a maximum of 2.50 x 10-6/K recommended in literature.
Die Kenntnis von Materialeigenschaften spielt bei der Entwicklung oder Optimierung von Betonen und Bauweisen für den Straßenbau sowie der Qualitätskontrolle und -sicherung eine bedeutende Rolle. Gleichermaßen bilden physikalische Materialkennwerte die Grundlage für die rechnerische Dimensionierung und die Restsubstanzbewertung von Betonfahrbahndecken. Einen relevanten Kennwert bei der Untersuchung thermisch induzierter Spannungs- und Verformungszustände stellt der thermische Ausdehnungskoeffizient von Beton dar. Dieser beeinflusst beispielsweise maßgeblich das Längsdehnungsverhalten des Deckensystems sowie das Ausmaß von Plattenkrümmungen und Fugenbewegungen. Im Zuge der systematischen Weiterentwicklung der rechnerischen Dimensionierung aber auch im Zusammenhang mit der gezielten Verbesserung der Gebrauchseigenschaften von Fahrbahndecken gilt es zu hinterfragen, ob lastunabhängige Formänderungseigenschaften, wie z. B. der thermische Ausdehnungskoeffizient der verwendeten Betone, aktuell ausreichend Beachtung finden, ob allgemeine Literaturwerte für die heutigen Fahrbandeckenbetone stets Gültigkeit besitzen und ob deren Implementierung in moderne Rechenmodelle zu validen Ergebnissen führt. Für eine empirische Herangehensweise ist die Verfügbarkeit adäquater Prüfverfahren von entscheidender Bedeutung. In Deutschland existiert aktuell jedoch kein standardisiertes oder genormtes Verfahren für die prüftechnische Bestimmung des thermischen Ausdehnungskoeffizienten von Beton. Daher wurden unter Beachtung straßenbauspezifischer Gesichtspunkte zwei Prüfansätze entwickelt, die in diesem Beitrag vorgestellt und hinsichtlich möglicher Messunsicherheiten und Messungenauigkeiten diskutiert werden. Außerdem erfolgt die Darstellung ausgewählter Ergebnisse aus Analysen an Bestandsbetonen aus dem BAB-Netz. Im Ergebnis sollen die Untersuchungen einen Beitrag zur Schaffung der prüftechnischen Voraussetzungen für eine abgesicherte Quantifzierung der thermischen Dehnung von Fahrbahndeckenbetonen leisten.
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
Ausgehend von den rechtlichen Grundlagen für die Luftreinhaltung sowie den Grenzwertfestlegungen für Feinstaub (PM10) sowie Stickoxide (NO2) wird auf die heutige Luftqualität in Städten mit Schwerpunkt Stuttgart eingegangen. Dargelegt werden die festgestellten Überschreitungen bei den Grenzwerten für PM10 und NO2. Eingegangen wird auf die Maßnahmen zur Reduzierung der Luftbelastung in Stuttgart und die Wirkungen in Bezug auf die Senkung der Grenzwert-Übersschreitungen beziehungsweise Jahresmittelwerte von PM10 und NO2 an den Hotspot-Stationen "Am Neckartor" und "Hohenheimer Straße". Abschließend wird ein perspektivischer Ausblick gegeben: obwohl die Luftsituation in den Städten kontinuierlich besser geworden ist, gibt es an stark befahrenen städtischen Straßen weiterhin Grenzwertüberschreitungen. Die EU-Vertragsverletzungsverfahren machen weitere Maßnahmen notwendig. Die Städte brauchen praxiserprobte Maßnahmen und keine langfristigen, kostspieligen Pilotversuche mit unsicherem Ausgang.
Um ein zuverlässiges Straßennetz aufrechtzuerhalten, ist es notwendig, neue innovative Ansätze in das Erhaltungsmanagement der Brückenbauwerke im Bundesfernstraßennetz zu integrieren und weiterzuentwickeln. Ergänzend zu den turnusmäßigen Bauwerksprüfungen nach DIN 1076 wird daher ein adaptives Konzept bereitgestellt, das es ermöglichen soll zum einen Zustandsveränderungen frühzeitig zu erfassen und zu bewerten und zum anderen mit Hilfe von erfassten Einwirkungen und Widerständen zukünftige Zustandsentwicklungen zu prognostizieren. Die zu konzipierenden Systeme setzen sich im Wesentlichen aus der Datenerfassung mit Hilfe von Sensorik und den zur echtzeitnahen Verwendung und Bewertung notwendigen Modellen zusammen. Im Rahmen mehrerer Forschungsprojekte wurden einzelne Bausteine eines solchen adaptiven Systems erarbeitet.
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
Structured road markings are becoming popular as edge line on high speed roads, ensuring night time visibility (retroreflection) during rain. These markings are often also "audio-tactile": vehicles (un)intentionally driving over it may produce much more tyre/road sound, which may be observed in the vehicle but also in the vicinity. The sound increase inside the car can be considered as a positive side effect, as it alarms the driver and may be very helpful for the prevention of "doze off" traffic accidents. The sound increase perceived outside the car however, may have a positive aspect as it can warn people on the emergency lane about the approaching vehicle, but it may as well annoy people living around. A method for the assessment of the acoustic properties of audio-tactile markings has been developed. It is mainly based on the "Close Proximity" (CPX) method, an ISO method intended for the acoustic assessment of pavements. The results of measurement campaigns with CPX trailers in Belgium and Germany according to a specially designed procedure are presented. The feasibility of the method is discussed. The research has been carried out in the frame of the standardization activities of the CEN working group CEN/TC226/WG2 "Horizontal signalization".
The grip between the road surface and vehicle tires is the physical basis for the moving of all vehicles in road traffic. In case of an accident the available grip level is one of the most relevant influence factors, influencing the causation and the procedure of the accident. However, the estimation of the grip level is not easy and therefore, is commonly not done on the accident scene. This is especially true for the measurement of the water depth. Until now, real accident databases provide no measurement data about the grip level and the water film depth and thus, the estimation of its influence is not possible yet. From the tyre manufacturers point of view, it is important to know about the road conditions (namely grip level, macro-texture, water depth, temperature) at the accident scene, as well as the operating conditions of the vehicles (braking, loss of control, speed, etc). These data is necessary to define relevant tyre traction tests for the end-user and for regulations. For this reason VUFO and Michelin developed a consistent method for the measurements of grip level and water depth for the accidents of the GIDAS database. The accident research team of Dresden, which documents about 1000 accidents with at least one injured person every year, is measuring the micro-roughness and the macro-roughness directly on the spot. For the measurement of the micro-roughness a Skid Resistance Tester (British Pendulum) is used. The Mean Texture Depth (describing the macro-roughness) is measured by the Sand Depth Method. Since June 2009, measurements for more than 700 accidents including 1200 participants have been carried out. In case of wet or damp road conditions during the accident, the water depth is measured additionally. Therefore VUFO and Michelin developed a special measurement device, which allows measurements with an accuracy of 1/10 millimetre. The measurement point at the accident scene is clearly defined and thus, the results are comparable for all different accidents and participants. The use of the GIDAS database and the accident sampling plan allows representative statements for the German accident scenario. With this data it is possible for the first time to have an accurate view of the road conditions at the accident scene. One possibility is a more detailed estimation of hydroplaning accidents using the actually measured water depths. The development of new testing methods and new tires can be based on the real situation of the road infrastructure. Furthermore, the combination of the technical GIDAS data and the measured road surface properties can also be used for the estimation of effectiveness of several safety systems like the brake assist and/or emergency braking systems. The calculation of a reduced collision speed due to the use of a brake assist is only one example for the application of real measured grip level data.
The GIDAS-investigation team of Dresden (VUFO) has documented more than 11.500 accidents since 1999. The documentation of the accident includes beside vehicle-, injury- and environmental-data very detailed reconstruction data. Within this accident investigation the VUFO began to record the skid resistance of the accident site in 2009. The measurements are divided in macro- and microroughness (Sand depth method and Portable Skid Resistance Tester-SRT-by Munro-Stanley London-©). Both methods are used to determine the skid resistance for more than 1000 passenger cars. The aim of the present study is to find out a relationship between the measured skid resistance, the road conditions and the friction coefficient, which is used to calculate the maximum accelerations and decelerations during a reconstruction of an accident. Basic approach to convert the SRT-value into the friction coefficient is the calculation of the theoretical absorbed energy of the spring rubber system of the swinging arm of lever. This absorbed energy is used to get the friction coefficient by using the equations for the work of friction. To consider the road-behavior, in correlation to the friction coefficient, the results will be merged with existing literature. Last step for this study will be a comparison between actual used friction coefficients all over the GIDAS-database and the theoretical results. The study shows, if it is possible to use the SRT-Measurement for the estimation of a friction coefficient for the reconstruction of a traffic accident. As expected, the GIDAS-Database and the additional measurement of the roughness of the road directly on the spot are an enormous useful dataset.
Having a look at safety to traffic and the prevention of accidents it can be observed that technical improvements in active safety of vehicles have let to various positive effects in this area. Among other components the tyre-road-contact takes a key role in the development of active safety technologies. All forces in accelerating, breaking and vehicle guidance have to be transmitted through the tyre-road contact area by friction forces. A common way to characterize a friction process is to identify the coefficient of friction μ between two touching materials. Even though there are several approaches to experimentially characterise road surfaces, no standard method exists. In this paper an overview of existing test methods is given. Furthermore the preliminary design of a newly developed portable test device with its possibility to investigate the tyre-road-friction of arbitrary roads or even places of accidents is shown.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.
Die Griffigkeit ist die maßgebende Größe für die Übertragung der Langs- als auch der Seitenkräfte von Reifen auf die Straßenoberfläche und hat somit einen erheblichen Anteil an der Straßensicherheit. In Deutschland erfolgt die Erfassung der Straßengriffigkeit im Rahmen von Bauverträgen sowie der Zustandserfassung und -bewertung (ZEB) mit dem Seitenkraftmessverfahren (SKM). Mit der Veröffentlichung der Technischen Prüfvorschriften für Griffigkeitsmessungen im Straßenbau (TP Griff-StB) (SKM) durch die Forschungsgesellschaft für Straßen- und Verkehrswesen (FGSV) am 29.04.2008 ist derzeit das aktuellste Dokument für Griffigkeitsmessungen im Rahmen von Bauverträgen sowie der Zustandserfassung und -bewertung von Bundesfernstraßen mit dem Seitenkraftmessverfahren (SKM) herausgegeben worden. Dieses Dokument löst die TP Griff-StB (SCRIM) mit ihren drei Allgemeinen Rundschreiben ab und fasst die Ergebnisse aus verschiedenen Forschungsprojekten und Erfahrungen aus den regelmäßigen Messungen der Messgerätebetreiber zusammen.
Zur Ergänzung der bestehenden Routineverfahren in der forensischen Blutalkoholanalytik wurde ein massenspektrometrisches Verfahren mit d6-Ethanol als internem Standard entwickelt. Ziel war die Anwendung eines beweissicheren Bestimmungsverfahrens, bei dem Ethanol über die Retentionszeit und Substanzeigenschaften identifiziert wird. Die Pilotstudie belegt, dass die forensische Blutalkoholbestimmung durch Anwendung eines gaschromatographischen und massenspektrometrischen Verfahrens mit Dampfraumanalyse routinemäßig möglich ist. Im Gegensatz zum GC- und ADH-Verfahren ist die massenspektrometrische Blutalkoholbestimmung beweissicher. Die Autoren empfehlen die Aufnahme in die Richtlinien zur Bestimmung der Blutalkoholkonzentration für forensische Zwecke. Die Arbeit wurde vom Bund gegen Alkohol und Drogen im Straßenverkehr e.V. (B.A.D.S.) unterstützt.
Diese Studie erfolgte als eine erste Prüfung der Frage, ob 0,1 Promille als Sicherheitszuschlag für eine Bestimmung eines Blutalkoholwertes von 0,1 Promille aus Gründen der Messunsicherheit angebracht und ausreichend ist. Beides trifft zu. Obwohl zur Zeit der Studie noch nicht bei oder unter 0,2 Promille kalibriert wurde, bestimmten alle Labors eine Blutalkoholkonzentration von 0,08 Promille mit einem Wert unter 0,18 g/L (Cmax ADH: 0,15 g/L = CmaxGC: 0,15 g/L = Blutalkoholkonzentration (BAK) von 0,12 Promille). Es bestand kein Bias zwischen beiden Verfahren. Festgestellte Standabweichungen: ADH: 0,021 g/L, GC: 0,025 g/L. Ein Sicherheitszuschlag von 0,1 Promille auf 0,1 Promille umfasst demnach vier Standardabweichungen und bietet für die neue Regelung im Paragrafen 24 Straßenverkehrsgesetz (StVG) bei der richtliniengemäß ausgeführten forensischen Blutalkoholbestimmung genügend Analysensicherheit.
Die Begutachtung der Fahreignung beinhaltet in Deutschland neben einer medizinischen Untersuchung und einer psychologischen Exploration gegebenenfalls auch die Anwendung anlassbezogener verhaltenswissenschaftlicher/psychologischer Testverfahren. Diese stellen keine isolierte Maßnahme dar, sondern sind Bestandteil eines Begutachtungsprozesses. Dabei stellt der sachgerechte Gebrauch von so genannten Grenzwerten unter Berücksichtigung der Einzelfallgerechtigkeit und der Einhaltung des Grundsatzes der Verhältnismäßigkeit eine unabdingbare Voraussetzung dar. Testwerte sind nicht absolut, sondern relativ und üben von daher einen eher geringen Einfluss auf das Gutachtenergebnis in Bezug auf eine Prognose des Verkehrsverhaltens aus. Im Bereich des Verkehrsverhaltens kommt es nicht entscheidend darauf an, ob eine im Milli- oder Nanobereich exakte Messgenauigkeit erreicht wird, sondern wie die verkehrsmedizinischen, verkehrspsychologischen, technischen und anderen Sachverständigen mit dem Messwert fachlich umgehen. So müssen im Bereich der Begutachtung der Fahreignung tätige psychologische und medizinische Sachverständige in der Lage sein, Befunde im Einzelfall fehler-, mangel- sowie widerspruchsfrei zu interpretieren. Dies beinhaltet auch, sich mit den Ergebnissen eines psychologischen Testverfahrens fach- und sachgerecht auseinanderzusetzen, nach Kompensationsmöglichkeiten zu suchen und gegebenenfalls eine psychologische Fahrverhaltensbeobachtung durchzuführen. Bei grenzwertigen Vorgaben handelt es sich nicht um "Cut-Offs", sondern um "kritische Grenzwerte", die im Zusammenhang mit mehreren anderen Faktoren zu werten sind.
Um ein Bild von der aktuellen Messunsicherheit bei der Bestimmung von Tetrahydrocannabinol (THC) in Serum zu erhalten, wurden von sieben forensisch-toxikologischen Laboren rechtsmedizinischer Institute Daten der letzten Jahre erhoben. Zur Abschätzung der Messunsicherheit wurde eine Einteilung in zufällige Fehler (Präzision) und systematische Fehler (Richtigkeit) vorgenommen. Ergebnisse zur Richtigkeit wurden aus Daten von Ringversuchen ermittelt. Es ergab sich eine mittlere erweiterte Messunsicherheit für die THC-Bestimmung von ca. 33 %, das heisst, bei einem Messwert von 1 ng/ml liegt der "wahre Wert" mit circa 95 prozentiger Wahrscheinlichkeit im Intervall zwischen 0,67 und 1,33 ng/ml. Dieses Ergebnis bestätigt, dass die verwendete Analytik geeignet ist, bei Konzentrationen um 1 ng/ml einen sicheren Substanznachweis zu führen. Es ist erkennbar, dass bei der THC-Bestimmung im Serum in der Regel der Richtigkeitsanteil an der Messunsicherheit größer ist als der Präzionsanteil.
Die aktuellen Richtlinien zur Bestimmung der Blutalkoholkonzentration (BAK) für forensische Zwecke (BAK-Richtlinie, 2007) lassen unter bestimmten Bedingungen auch zwei verschiedene gaschromatographische Analysen anstatt der häufig angewandten Kombination Gaschromatographie und enzymatische Methode ADH zur Bestimmung des Blutalkoholgehaltes zu. Untersucht wurde die Messpräzision zweier gaschromatographischer Verfahren bei der Alkoholanalytik im Vergleich zur häufiger angewandten Methodenkombination. In mehr als 50 Prozent der Fälle hat sich bei den verglichenen Methodenkombinationen ein identischer Mittelwert ergeben. Ansonsten waren die Abweichungen gering. Damit werden die hohen Anforderungen, die an die forensische Blutalkoholbestimmung gestellt werden, durch die modernen Laborautomaten erfüllt.
During a lifecycle a tyre undergoes degradations due to mechanical wear and chemical ageing which affect not only durability and safety but also tyre/road noise emission and rolling resistance. This paper presents a study with the purpose to study how much tyre/road noise and rolling resistance change when car tyres are worn down from the original 8 mm tread depth to 2 mm, and when chemical ageing of the tyre rubber is simulated by exposure to heat. Six car tyres of different types were selected for the study which were worn on a wear machine in steps of 2 mm tread depth. Before, between and after these wear sessions tyre/road noise and rolling resistance were measured on two drum facilities with different surface textures, including replicas of ISO surfaces. Additionally, coast-by and CPX measurements were made on outdoor ISO test tracks. The results show that the wear and age effect was low on ISO surfaces but dramatic (noise increased with wear) on the rough-textured surface and high but opposite on an extremely smooth surface.
Der Beitrag berichtet in einem ersten Teil über die in den Niederlanden angewendeten Inspektionstechniken zur Feststellung von Schäden (Rissen) bei orthotropen Stahlfahrbahnplatten und in einem zweiten Teil über die Instandsetzung der Moerdijkbruecke mit einer zusätzlichen Deckschicht aus bewehrtem hochfesten Stahlfaserbeton. Die Ausführungen zu den Inspektionstechniken umfassen die visuelle Inspektion, magnetische Inspektion, Farbeindringprüfung, Ultraschallprüfung und Diffraktionseffekt bei Anstrahlen von Fehlern (Time of Flight Diffraction (TOFD)) sowie radiographische Untersuchungen und das Wirbelstromverfahren. Für jede dieser Methoden wird ihre Wirkungsweise, Handhabung und der Anwendungsbereich angegeben. Die Moerdijkbrücke ist eine der meistbefahrenen Brücken in den Niederlanden mit einem erheblichen Schwerverkehrsaufkommen und weist etliche Schäden am Deckblech auf. Die bisher durchgeführte Instandsetzung durch Ausbessern der Längsschweissnähte führte nicht zum erhofften Erfolg. Der Bauherr entschloss sich daher, die Gussasphaltschicht durch einen bewehrten hochfesten Stahlfaserbeton mit einer Dicke von 5 cm mit Verbund zum Stahldeckblech zu ersetzen. Die Spannungen im Deckblech konnten auf diese Weise um einen Faktor 4 bis 5 reduziert werden. Die Methode reagiert jedoch empfindlich auf Abweichungen der Mischungsverhältnisse des Betons und der Viskosität.
Federal highway A 26 in Germany : reinforced dams in soft soils - control method according DIN 1054
(2004)
In 2001 the construction of the Federal Highway A 26 in Lower Saxony (north of Germany) was started. In this area the underground is without any substantial bearing capacity as it consists of soft layers ( clay, peat) with a thickness of up to 12 m. Because it was not possible to exchange the soil neither completely nor partially pre-loading procedure (consolidation method) was chosen for this construction. Short- and long-term stability are ensured by the use of high-tensile fabrics for reinforcement at the dam basis. The vertical and horizontal deformations and the stress changes in the soil, caused by the pre-load procedure, has to be controlled by special geotechnical measurements. Additionally, in the higher parts of the dam the strain behaviour of the high-tensile fabrics is measured. These measurements form the basis for the application of the control method according DIN 1054. In this article, the special circumstances of this project are described. Further on the geotechnical measurements, the winning and evaluation of the necessary parameters of the subsoil, and the consequences of these data for the ongoing of the project are laid down. Intermediate results of the geotechnical measurements are described.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
Bewertung der Fahrzeug-Fußraumintrusionen beim Offset Frontaltest gegen das Verformungselement
(1998)
In den Tests nach dem neuen Frontaltestverfahren (Entwürfe ECE R.94 sowie Richtlinie 96/79/EG und Ergänzung zu RL 70/156/EWG) entstehen hohe Verformungen der Fußräume der Versuchsfahrzeuge. Die Bewertung der Gefährdung der Insassen durch Intrusion, vorwiegend der Spritzwand begleitet von heftigen Bewegungen der Pedale, soll durch am Dummy zu messende Schutzkriterien erfolgen. Es ist vorgesehen, an den Dummies die Verschiebung des Schienbeins gegen das Knie, die Längskraft im Unterschenkel und den sogenannten Tibia Index zu messen. Um dieses zu ermöglichen, mussten an den vorhandenen Dummy-Unterschenkeln konstruktive Änderungen vorgenommen werden. Über die Herleitung der Schutzkriterien, Fragen bei der Anwendung dieser Kriterien sowie die technischen Einzelheiten und die Zertifizierung der neuen Dummy-Unterschenkel, welche die erforderlichen Messungen erlauben, wird berichtet.
Es wird der Frage nachgegangen, mit welchen statistischen Verfahren der simultane Vergleich mehrerer Messwerte verschiedener Testverfahren vorgenommen werden kann. Hierzu werden vier Methoden vorgestellt: der multiple Vergleich, die ANOVA-Varianzanalyse, die Methode der multiplen Endpoints sowie die Akkumulationsstatistik. Die Demonstration erfolgt an den Merkmalen periphere Wahrnehmung, Daueraufmerksamkeit, Tachistoskop, Tracking und mittlere Entscheidungszeit. Untersucht wurden 2 mal 13 Probanden (Methadon- und Kontrollgruppe). Es zeigte sich, dass die Akkumulationsstatistik eine optimale, für die Thematik äquivalente Bewertung für mehrere simultan gemessene fahrrelevante Leistungen darstellt. Voraussetzung für den Einsatz ist allerdings, dass die Verkehrswissenschaften sich über Art, Umfang und Gewichtung der verschiedenen Komponenten der fahrrelevanten Leistungen einig sind.
Die meisten der in Betracht kommenden Zwischenquerschnitte werden durch die derzeitigen Entwurfsrichtlinien nicht abgedeckt. Hinreichende Erkenntnisse über ihre Leistungsfähigkeit, die bei verschiedenen Belastungen erzielbaren Verkehrsqualitäten und vergleichende Angaben zum Sicherheitsniveau der Zwischenquerschnitte liegen nicht vor. Die Projektgruppe "Zwischenquerschnitte" der Bundesanstalt für Straßenwesen untersucht daher die Vor- und Nachteile der Zwischenquerschnitte mit dem Ziel, Einsatzbereiche für die verschiedenen Ausbildungsformen von Querschnitten zu entwickeln. Der Bericht gibt einen Überblick über bisherige Aktivitäten der Projektgruppe und stellt erste Zwischenergebnisse der Untersuchung vor. Bisherige Messungen zeigen, dass der besondere Vorteil der zwei- und dreiseitigen Zwischenquerschnitte in der Verbesserung der Überholsituation liegt. Für die Beurteilung vierstreifiger Zwischenquerschnitte kann bislang erst die Aussage gemacht werden, dass immer dann, wenn die Verkehrsbelastung tatsächlich einen Querschnitt mit 4 Fahrstreifen erforderlich macht, man die beiden Fahrrichtungen aus Gründen der Verkehrssicherheit baulich trennen sollte.