Filtern
Erscheinungsjahr
- 2011 (4) (entfernen)
Dokumenttyp
Schlagworte
- Analysis (math) (4) (entfernen)
Institut
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
Ziel des Forschungsprojektes "Griffigkeitsprognose an offenporigen Asphalten (OPA)" ist die Weiterentwicklung und Optimierung der Messverfahren und die Entwicklung einer Vorgehensweise zur Griffigkeitsprognose für OPA. Hierzu wurde das Projekt aufgeteilt in den Projektteil 1 "Bestandsaufnahme an vorhandenen Strecken" und den Projektteil 2 "Neue Baumaßnahmen". Im ersten Projektteil wurden die Grundlagen für die Griffigkeitsprognose erarbeitet und Erfahrungen mit dem Seitenkraftmessverfahren (SKM) auf offenporigen Asphalten gewonnen. Hierzu wurden Streckenabschnitte von Bundesfernstraßen zur Untersuchung ausgewählt, die bereits mehrere Jahre unter Verkehr lagen. Ziel des zweiten Projektteils ist die Verifizierung und Weiterentwicklung der im ersten Teil hergeleiteten Vorgehensweise zur Griffigkeitsprognose für offenporige Asphaltdeckschichten. Hierzu wurden Streckenabschnitte ausgewählt, die zu Projektbeginn mit OPA erneuert bzw. instandgesetzt worden sind. Diese Streckenabschnitte wurden für einen Zeitraum von vier Jahren beobachtet. Zur Feststellung des Nullzustandes wurden unmittelbar vor oder nach der Verkehrsfreigabe Bohrkerne entnommen und Messungen mit dem Skid-Resistance-Tester (SRT) durchgeführt. An den Bohrkernen und an Walzsegmentplatten, die anhand von Rückstellproben hergestellt wurden, erfolgten Griffigkeitsprognosen nach dem Polierverfahren Wehner/Schulze (PWS). Die Ergebnisse der bauvertraglichen SKM-Abnahmeprüfungen ergänzten die Datenbasis. Nach zwei und vier Jahren Verkehrsbelastung erfolgten weitere SKM-Messungen, SRT-Messungen sowie Bohrkernentnahmen für PWS-Messungen. Anhand der so gewonnenen Datenbasis wurden die Griffigkeitsentwicklungen dokumentiert und die Ergebnisse der unterschiedlichen Messverfahren vergleichend ausgewertet. In Voruntersuchungen zum Verfahren PWS wurden Einflüsse auf die Präzision aus der Lagerung und Montage der Probekörper in die Prüfeinrichtung untersucht. Probekörper mit deutlichem Bindemittelüberschuss und solche mit künstlichen Gesteinskörnungen zeigten dabei deutliche Veränderungen während längerer Lagerungsdauer. Desweiteren konnte gezeigt werden, dass der Einfluss der Probenvorbehandlung (Sandstrahlen) auf die Ergebnisse der Prognoseprüfung ab einer Beanspruchung von circa 45.000 Überrollungen zu vernachlässigen ist. Hinsichtlich der Prognose der Griffigkeit mit dem PWS-Verfahren wurde festgestellt, dass ein Endpolierwert nach circa 180.000 Überrollungen erreicht wird. Die Prognosekurven der verschiedenen Streckenabschnitte zeigen dabei einen sehr ähnlichen Verlauf, wenn auch auf verschiedenen Griffigkeitsniveaus. Signifikante Abhängigkeiten von der Wahl der Gesteinsart, Bindemittelart oder Mischgutart konnten dabei nicht festgestellt werden. Ebenso sind keine Unterschiede zu erkennen zwischen Bohrkernen und den Walzsegmentplatten. Mithilfe der PWS- und SRT-Messungen konnte der deutlich griffigkeitsmindernde Einfluss des Bindemittelüberschusses unmittelbar vor bzw. nach der Verkehrsfreigabe sowie die weitere Griffigkeitsentwicklung dokumentiert werden. Wie auch schon die Ergebnisse ähnlicher Forschungsprojekte gezeigt haben, gelingt der unmittelbare Bezug der PWS-Überrollungen zur realen Verkehrsbelastung nicht. Die Angabe eines Endpolierwertes und evtl. die qualitative Beurteilung der Prognosekurve sind daher für die Prognose entscheidend. Desweiteren wurden Texturaufnahmen mit dem T3D-Messystem (Prinzip der Streifenprojektion) und einem Digitalmikroskop gemacht. Für die Herstellung eines Zusammenhanges von Griffigkeit und Textur stellten sich die aus der Textur abgeleiteten Rauheitskenngrößen nur bedingt geeignet dar. Die Parameter Flächen- und Kantenschärfe zeigen einen deutlichen Zusammenhang zu den gemessenen Griffigkeiten. Die Formulierung dieser Zusammenhaenge ist Teil eines laufenden Forschungsprojektes. Zur Beantwortung der Frage, ob die Einführung von OPA-Deckschichten auf BAB einen Einfluss auf das Unfallgeschehen hat, wurde die Analyse des ersten Projektteils fortgeführt. Hierzu wurde die Unfallentwicklung der OPA-Streckenabschnitte mit der Unfallentwicklung auf Kontrollstrecken, die andere Deckschichtarten aufweisen, verglichen. Sowohl auf den OPA-Strecken als auch auf den Kontrollstrecken ist eine rücklaeufige Unfallentwicklung eingetreten. In der Summe zeigt sich, dass die offenporigen Asphaltdeckschichten keinen negativen Einfluss auf das Unfallgeschehen haben.