Filtern
Erscheinungsjahr
Dokumenttyp
- Buch (Monographie) (697)
- Konferenzveröffentlichung (212)
- Wissenschaftlicher Artikel (108)
- Arbeitspapier (26)
- Bericht (24)
- Teil eines Buches (Kapitel) (12)
Sprache
- Deutsch (899)
- Englisch (178)
- Mehrsprachig (2)
Schlagworte
- Germany (1079) (entfernen)
Institut
- Sonstige (633)
- Abteilung Straßenverkehrstechnik (159)
- Abteilung Verhalten und Sicherheit im Verkehr (130)
- Abteilung Brücken- und Ingenieurbau (74)
- Abteilung Straßenbautechnik (62)
- Abteilung Fahrzeugtechnik (50)
- Präsident (11)
- Stabstelle Presse und Öffentlichkeitsarbeit (4)
- Stabstelle Forschungscontrolling, Qualitätsmanagement (1)
- Zentralabteilung (1)
In the paper it is investigated to what extend one can extrapolate the detailed accident database GIDAS (German In-Depth Accident Study), with survey area Hanover and Dresden region, to accident behavior in other regions and countries within Europe and how such an extrapolation can be implemented and evaluated. Moreover, it is explored what extent of accident data for the target country is necessary for such an extrapolation and what can be done in situations with sparse and low accident information in a target region. It will be shown that a direct transfer of GIDAS injury outcomes to other regions does not lead to satisfactory results. But based on GIDAS and using statistical decision tree methods, an extrapolation methodology will be presented which allows for an adequate prediction of the distribution of injury severity in severe traffic accidents for European countries. The method consists essentially of a separation of accidents into well-described subgroups of accidents within which the accident severity distribution does not vary much over different regions. In contrast the distribution over the various subgroups of accidents typically is rather different between GIDAS and the target. For the separation into the subgroups meaningful accident parameters (like accident type, traffic environment, type of road etc.) have been selected. The developed methodology is applied to GIDAS data for the years 1999-2012 and is evaluated with police accident data for Sweden (2002 to 2012) and the United Kingdom (2004 to 2010). It is obtained that the extrapolation proposal has good to very good predictive power in the category of severe traffic accidents. Moreover, it is shown that iterative proportional fitting enables the developed extrapolation method to lead to a satisfactory extrapolation of accident outcomes even to target regions with sparse accident information. As an important potential application of the developed methodology the a priori extrapolation of effects of (future) safety systems, the operation of which can only be well assessed on the basis of very detailed GIDAS accident data, is presented. Based on the evaluation of the presented extrapolation method it will be shown that GIDAS very well represents severe accidents, i.e. accidents with at least one severely or fatally injured person involved, for other countries in Europe. The developed extrapolation method reaches its limits in cases for which only very little accident information is available for the target region.
Berichtet wird über ein Expertengespräch, das am 25. Januar 2000 in der Bundesanstalt für Straßenwesen stattfand. Thema des Expertengespräches war die Auslegung der Ausführungen des Paragraphen 70 FeV (Fahrerlaubnisverordnung) zur amtlichen Anerkennung von Kursen zur Wiederherstellung der Kraftfahreignung. Beteiligt waren Vertreter des Bundesministeriums für Verkehr, Bau- und Wohnungswesen, der Länder, des Kraftfahrt-Bundesamtes, von Hochschulen sowie der Träger von Kursen zur Wiederherstellung der Kraftfahreignung und Praktiker aus den Bereichen der Rehabilitation und der Psychotherapie.
Es wird über die Ergebnisse eines Expertengespräches zur Fahreignung und -tüchtigkeit von Schmerzpatienten unter dem Einfluss von Opiaten berichtet. Das Expertengespräch sollte wissenschaftlich fundierte Entscheidungshilfen für eine Änderung des Paragraphen 24a StVG liefern und fand im Auftrag des Bundesministeriums für Verkehr bei der Bundesanstalt für Straßenwesen statt.
Berichtet wird über die Ergebnisse eines bei der BASt durchgeführten Expertengesprächs zu den Anforderungen von Anlage 5(2) der Fahrerlaubnisverordnung, in der die Begutachtung der psychischen Leistungsfähigkeit von Personen in der Fahrgastbeförderung geregelt ist. Es werden die bisherigen Erfahrungen in der Begutachtung wiedergegeben, Handlungsbedarf für Verwaltungspraxis und Forschung wird aufgezeigt.
Aufgrund des demografischen Wandels werden in der Zukunft immer mehr ältere Menschen ein Kraftfahrzeug führen. Das vorliegende Projekt soll Erkenntnisse dazu liefern, wie unter Berücksichtigung der Verkehrssicherheit die Mobilität der älteren Fahrer so lange wie möglich erhalten werden kann. Unfallanalysen zeigen, dass ältere Kraftfahrer typische Fahrfehler bzw. Unfälle begehen. Unklar ist derzeit die genaue Ursache hierfür, vor allem vor dem Hintergrund der langjährigen Erfahrung älterer Kraftfahrer, welche eher eine äußerst geringe Unfallrate vermuten ließe. Ziel der vorliegenden Untersuchung war es, tiefere Erkenntnisse äber die Ursache von Fahrfehlern älterer Kraftfahrer zu gewinnen, um daraus Anforderungen an die technische Weiterentwicklung von Fahrerassistenzsystemen ableiten zu können. Diese Fahrerassistenzsysteme sollen speziell älteren Autofahrern Hilfestellung zum sicheren Führen von Kraftfahrzeugen bieten. In dem folgenden Laborexperiment wurde ein Doppeltätigkeits-Paradigma verwendet, indem eine Spurhalteaufgabe mit einer peripheren Lichtreizaufgabe kombiniert wurde. Die peripheren Lichtreize wurden den Probanden bilateral in zwei verschiedenen Abständen vom zentralen Punkt des Sehens (20 Grad und 60 Grad) präsentiert. Die Aufgaben wurden von älteren (65+) und jüngeren Kraftfahrern (22-45) zuerst einzeln, dann in Kombination durchgeführt. Um Aufschluss über mögliche Ursachen von Leistungsbeeinträchtigungen erhalten zu können, wurde neben der Erfassung von Verhaltensdaten (Spurabweichungen, Reaktionszeit, Anzahl der Auslassungen) ein Elektroenzephalogramm abgeleitet, welches Einblicke in die zugrunde liegenden neuronalen Verarbeitungsmechanismen ermöglicht. Wie erwartet, zeigten Ältere in der Spurhalteaufgabe schlechtere Leistungen als Jüngere, besonders bei gleichzeitiger Durchführung der Lichtreizaufgabe (Doppel-Aufgabe). In der Lichtreizaufgabe unterschieden sich die Leistungen der Altersgruppen nur bei Lichtreizen, die im 60 Grad Sehwinkel auftraten. Die Älteren reagierten hier langsamer und zeigten mehr Auslassungen als die Jüngeren. Überraschenderweise zeigten alle Versuchspersonen weniger Auslassungen in der Doppel-Aufgabe. Mittels Elektroenzephalogramm wurde anhand der ereigniskorrelierten Potenziale (EKP) deutlich, dass die Defizite Älterer nicht in einer Einschränkung der frühen Verarbeitung peripherer Reize (P1) liegen, da die P1 Amplitude bei Älteren sogar höher war als bei Jüngeren. Die N2 Amplitude, welche Hinweise auf die Verschiebung der Aufmerksamkeit gibt, war bei Jüngeren hingegen bei weiter peripher liegenden Reizen (60 Grad Sehwinkel) erhöht, was einen fronto-zentral fokussierten Kontrollprozess widerspiegelt. Die Orientierung auf den peripheren Reiz (P3a) war bei Älteren geringer ausgeprägt sowie auch die Zuordnung von Verarbeitungsressourcen (P3b) vor allem bei peripheren Lichtreizen. Es liegen zudem Hinweise darauf vor, dass Ältere verlängerte Reaktionszeiten aufgrund einer verzögerten Reaktionsaktivierung aufweisen. Mit dem vorliegenden Experiment konnte also gezeigt werden, dass die schlechteren Leistungen der älteren Versuchspersonen nicht auf periphere Sehleistungsmängel zurückzuführen sind, sondern einem späteren kognitiven Verarbeitungsprozess zuzuschreiben sind. Die Ergebnisse werden vor dem Hintergrund der Literatur und der Erfordernisse technischer Unterstützungen älterer Kraftfahrer diskutiert.
Data concerning accidents involving personal injury which have been collected in the context of in-depth investigations on scene in the Hannover area since 1973 and in the Dresden area since 1999 represent an important basis for empirical traffic safety research. At national and international level various analyses and comparisons are carried out on the basis of "in-depth data" from the above mentioned investigations. In-depth data play a decisive role e.g. within the validation of EuroNCAP results on secondary safety (crashworthiness) of individual passenger car models. Thus, statistically sound methods of data analysis and population parameter estimation are of high importance. Since the 1st of August 1984 the "in-depth investigations on scene" in the Hannover area have been carried out according to a sampling plan developed by HAUTZINGER in the context of a research project on behalf of BASt. In the meantime a second region of in-depth investigation on scene was added with surveys in Dresden and the surrounding area. Internationally, the acronym GIDAS (German In-Depth Accident Study) is commonly used for the two above mentioned surveys. The objective of a current research project (topic of this contribution) is, among other things, to examine and adjust the previous weighting and expansion method for the two regional accident investigations to the current general conditions.
High demands on exhaust emissions of passenger cars and light commercial vehicles require complex technologies. The three-way catalytic converter is an essential part of state of the art emission control systems. If a catalytic converter is damaged or its effectiveness deteriorates, it can be replaced by a replacement converter. Replacement catalytic converters from the aftermarket are approved on the basis of Regulation No 103 of the UNECE - United Nations Economic Commission for Europe. According to this regulation the replacement catalytic converter shall be designed, constructed and capable of being mounted so as to enable the vehicle to comply with the provisions taken as a basis for its type approval. Furthermore the pollution emissions must be effectively limited throughout the entire normal service life of the vehicle under normal operating conditions. In the context of the research project, the durability of replacement catalytic converters was examined. A VW Golf with emission standard Euro 4, 1.4 l petrol engine (55 kW) was selected as a test vehicle. At the start of the examinations, the vehicle showed a mileage of 75,000 km. The selected vehicle was regularly serviced in accordance with the manufacturer's specifications. No emission-relevant faults were recorded by the OBD system. The initial control measurement of the vehicle in as-delivered condition with the originally installed catalytic converter showed that the corresponding emissions of the regulated pollutants were considerably below the Euro 4 emission limits to be applied. Subsequently, an original replacement catalytic converter, which was purchased from an authorised dealer, and 4 catalytic converters purchased in the independent aftermarket, were examined. The replacement catalytic converters were conditioned according to the specifications of ECE Regulation No 103 and then measured in new condition. The catalytic converters were then aged on a burner test rig. Here a total mileage of 80,000 km was simulated. After 10,000 km and 40,000 km, the ageing was interrupted and the exhaust gas emissions of the test vehicle with the aged catalytic converters were measured. The examination was ended as soon as a limit value had been exceeded. The results of the project indicate that with the replacement systems for the after-treatment of exhaust gases available in the independent aftermarket, considerable quality differences can occur. At the end of the ageing over a distance of 80,000 km only the original replacement catalytic converter and one replacement catalytic converter from the independent aftermarket complied with the Euro 4 emission limits. With one replacement catalytic converter, the Euro 4 emission limits were already exceeded in new condition. With another replacement catalytic converter, the examination was aborted after 10,000 km ageing and with a further catalytic converter after 40,000 km ageing due to the Euro 4 emission limits being exceeded. The ECE Regulation No 103 provides for a test of durability of such systems over 80,000 km, but also alternatively enables the use of fixed deterioration factors. In practice, the durability of the replacement systems for the after-treatment of exhaust gases is guaranteed by their manufacturers. However, replacement catalytic converters are rarely inspected as part of the approval. In-use compliance provisions for replacement systems for the after-treatment of exhaust gases are not mentioned in the corresponding specifications. The results of this study indicate that the requirements in the ECE Regulation No 103 are not adequate to ensure the durability of replacement catalytic converters.
Mobility plays an important role in the Federal Republic of Germany. Motorised private transport and, consequently, passenger vehicles are the crucial factor. Vehicles should be environmentally and socially compatible yet also economically efficient at the same time. The crucial factor for pollution of the environment from road traffic is the exhaust emissions of the vehicles on the road. This is why, with the Directive 98/69/EC and the related introduction of exhaust emission standard Euro 3, the testing of the conformity of passenger and light commercial vehicles (in-service conformity check) was introduced. Vehicles already on the roads are to be examined again under type examination conditions (Type I Test) after a statistical selection process. In this way it is to be ensured that the systems and components relevant for the exhaust emissions of a vehicle will also function after several thousand kilometres. This is why the vehicles are checked again during in-service conformity check with respect to their limited pollution components. Due to the ever greater significance of CO2 emissions, both the CO2 emissions and the fuel consumption were included in this research project. For the success of such a project the choice of vehicle is of critical importance. Since this is the only way it is possible to also obtain a representative result. Therefore, in addition to the selection criteria required by law, statistical and technical criteria are also considered. The vehicle owners were selected on a random basis. All test vehicles were checked with respect to their pollutant components in the emissions laboratory in accordance with their standard. By law the same testing conditions apply in an in-service conformity check as in the relevant type approval. In this research project a total of 17 vehicle types were examined. Six types were equipped with positive-ignition engines and 11 types with compression ignition engines. Both groups were to each include vehicles of the limits Euro 4 and Euro 5. For vehicle types with positive-ignition engines, there was one type with the exhaust emission standard Euro 5. All others satisfied the exhaust emission standard Euro 4. For the vehicle types with compression ignition engines, 4 types satisfied exhaust emission standard Euro 5 and 7 types fulfilled exhaust emission standard Euro 4. Among the vehicle types with compression ignition and exhaust emission standard Euro4, there were 4 types of category M1 and 3 types of category N1 of class III. The aim of the research project is to examine the exhaust emissions in-service conformity of passenger and light commercial vehicles in operation to draw conclusions concerning the durability of engine components and systems for exhaust emission treatment. Overall in this in-service conformity testing programme, we were able, in accordance with the statistical procedure, to assess all 17 of the vehicle types tested as "positive". With the exception of one vehicle type, it was possible to conclude the random test for all vehicle types tested with the minimum random sample. This means that all 3 vehicles of one type in as-delivered condition complied with or fell below the respective limits for pollutant emissions according to the criteria of the statistical procedure. In the case of one vehicle type, where the random sample had to be enlarged, it was necessary to examine a total of 8 vehicles. Furthermore, with all vehicle types the CO2-emissions and fuel consumption (Type I Test) were determined to subsequently compare the measured CO2 emissions with those of the manufacturers. Of the 17 vehicle types examined, eleven vehicle types complied with the relevant manufacturers" values or fell below them. With six vehicle types, the CO2 emissions were more than the permissible 4% above the manufacturer- value during the Type I Test.
The paper gives an overview of the recent (mostly 2012) figures of killed bus/coach occupants (drivers and passengers) in 27 Member States of the European Union as reported by CARE. The Evolution of the figures of bus/coach occupants killed in road accidents urban, rural without motorway and on motorways from 1991 to 2010 in 15 Member States of the EU supplements this information. More detailed are the figures reported for Germany by the Federal Statistics. The paper displays long-term evaluations (1957 to 2012) for killed, seriously and slightly injured occupants in all kinds of buses/coaches. Midterm evaluations (1995 to 2012) of the figures of fatalities and casualties are displayed for different busses according to their identification of road using as coaches, urban buses, school buses, trolley buses and "other buses". To be able to compare the evolutions of the safety of vehicle occupants it is customary to use different risk indicators. Calculations and illustrations for three often used indicators with their development over time are given: fatalities, seriously injured and slightly injured per 100,000 vehicles registered, per 1 billion (109) vehicle-kilometres travelled and per 1 billion (109) person-kilometres. These indicators are shown for occupants of cars, goods vehicles and buses/coaches. For the period from 1957 until 2012 it is obvious, that for all three vehicle categories analysed there was a clear long-term trend towards more occupant safety in terms of casualties per vehicles registered and per vehicle mileage. This was most significant for car occupants but it can be seen for bus/coach occupants and goodsvehicle occupants as well. Figures of killed occupants and of casualties related to person-kilometres are calculated and displayed for the shorter period 1995 to 2012. Here it becomes obvious that the bus/coach is still the safest mode of transport for the occupants of road vehicles. Graphs for the casualty risk indices still show significantly higher risks for car occupants despite the corresponding curve moved sustainable downwards. It is remarkable, that the risks of being killed or injured for the occupants of urban buses is growing whereas the corresponding risk for the occupants of coaches in line traffic tends downwards. The article ends with a short comparison and discussion of the risk indicators which are actually published for the occupants (driver and passengers) of cars and the passengers of buses/coaches, railroads, trams and airplanes. The interpretation of such information depends on the perception and it seems that for a complete view not only one indicator should be used and the evolutions of the indicator values during longer periods (as displayed with examples in the paper) should also be taken into account.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.