Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (62)
- Buch (Monographie) (41)
- Wissenschaftlicher Artikel (12)
- Teil eines Buches (Kapitel) (2)
- Bericht (2)
Schlagworte
- Simulation (119) (entfernen)
Pedestrian and cyclist are the most vulnerable road users in traffic crashes. One important aspect of this study was the comparable analysis of the exact impact configuration and the resulting injury patterns of pedestrians and cyclists in view of epidemiology. The secondary aim was assessment of head injury risks and kinematics of adult pedestrian and cyclists in primary and secondary impacts and to correlate the injuries related to physical parameters like HIC value, 3ms linear acceleration, and discuss the technical parameter with injuries observed in real-world accidents based documented real accidents of GIDAS and explains the head injuries by simulated load and impact conditions based on PC-Crash and MADYMO. A subsample of n=402 pedestrians and n=940 bicyclists from GIDAS database, Germany was used for preselection, from which 22 pedestrian and 18 cyclist accidents were selected for reconstruction by initially using PC-Crash to calculate impact conditions, such as vehicle impact velocity, vehicle kinematic sequence and throw out distance. The impact conditions then were employed to identify the initial conditions in simulation of MADYMO reconstruction. The results show that cyclists always suffer lower injury outcomes for the same accident severity. Differences in HIC, head relative impact velocity, 3ms linear contiguous acceleration, maximum angular velocity and acceleration, contact force, throwing distance and head contact timing are shown. The differences of landing conditions in secondary impacts of pedestrians and cyclists are also identified. Injury risk curves were generated by logistic regression model for each predicting physical parameters.
Among European Countries, Spain first issued a Standard, UNE 135900:2005, further updated in 2008, that deals with homologation and effectiveness evaluation of road restraint systems components designed to reduce harm for bikers impacting on them. An in depth analysis and critical review of this standard is reported in this paper. Beside a close examination of the standard requirements, numerical models of the crash test stated by the standard have been set up and simulated to study the effects of slight speed and approach angle variations on test results, remaining within tolerance gaps allowed by the standard. Model were validated against experimental data. Together with the expected increasing severity of the impact according with speed, a strong influence of approach angle on injury parameters was found. Possible improvements to the norm, in order to make it more robust, are suggested.
The need of passive safety devices, able to reduce the accidents and the severity of injuries suffered by motorcyclist, distinctly arises from data on accident statistics. In this paper, the effectiveness of an airbag device fitted in the biker- garments has been verified through various numerical simulations. Two simple test conditions were defined, in order to investigate the performance of the device both for back and front impacts, and simulated at various impact speeds. With the aim of providing more information about the actual capability of the airbag to reduce the severity of the injuries, one of accident scenario described by ISO 13232:2005 has been also investigated, checking the real effectiveness of the airbag strap-based firing system too. Confrontation of injury indexes resulting from simulation with and without airbag made possible a realistic evaluation of the harm reduction induced by the airbag presence.
Accidents involving two wheels vehicles represent one of the more important types of accidents in Europe. These accidents are usually not easy to reconstruct specially for the analysis of the injuries and its correlation with accident dynamics and evidences. Different methodologies are applied in this work for the reconstruction of two wheeler accidents, especially accident involving motorcycles. From the typologies of road evidences like skid marks, to the use of Pc-Crash and the use of Madymo models, different reconstruction of real accidents are presented. One of the questions that sometimes arise for legal purposes when some type of head injuries arise is if the occupant was wearing or not a helmet. The correlation of head injuries with the use of the helmet is a very important issue, therefore an important legal aspect. One of the key questions for the reconstructions that is difficult to analyze, is if the vehicle occupant, was or not, wearing the helmet. Based on the previously collected information, a generic model of a helmet was developed on CAD 3D, followed by its conversion into finite elements, all in order to perform impact tests using the Madymo software that would help improve the helmet- safety, but that also can be used as a tool in accident reconstruction.
Impact severity is a fundamental measure for all in-depth crash investigation projects. One methodology used in the UK is based on the US Calspan software package CRASH3. The UK- in-depth crash investigation studies routinely use AiDamage3 a software package which is based on an updated version of the original CRASH3 algorithm, including enhancements to the vehicle stiffness coefficients. Real world accident-damaged vehicles are measured and their crush is correlated with a library of stiffness coefficients. These measurements are then used, along with other parameters, to calculate the crash energy and equivalent changes of velocity of the vehicles (delta-v), which is a measure of the impact severity. UK in-depth accident studies routinely validate the crash severity methodologies applied as the vehicle fleet changes. This is achieved by analysing crash test data and using the appropriate residual crush damage and other inputs to AiDamage3 and checking the program- outputs with the known crash severity parameters. This procedure checks, at least in part, the default stiffness values in the data libraries and the reconstruction methods used.
The focus of the technical innovation in the automobile industry is currently changing to sensor based safety systems, which are operating in the pre-crash phase of an accident. To get more information about this pre-crash phase for real accidents a simulation of this phase using the GIDAS database is done. The basics for this simulation are geometrical information about the accident location and the exact accident data out of the GIDAS database. This aggregated information gives the possibility to simulate an exact motion for every accident participant, using MATLAB / SIMULINK, in the pre-crash phase. After the simulation the information about the geometrical positions, the velocities and maneuvers of the drivers to an individual TTC (time to collision) are available. With those results it is possible to develop new useful sensor geometries using pre-crash scatter plots or estimate the efficiency of implemented active safety systems in combination with sensor characteristics. This simulation can be done for every reconstructed accident included in the GIDAS database, so these results can represent a wide spread basis for the further development of active safety systems and sensor geometries and characteristics
Pedestrian accidents are one of the major concerns related with road accidents around the world. Portugal has one of the highest rates of pedestrian fatalities in Europe. In this paper an overview conditions were the pedestrian accidents occurred in Portugal is presented. In the last years, a project related with the pedestrian accidents has run in Portugal for the period 2004-2006 where 603 people died, 2097 have been severely injured and about 17000 slightly injured. Within this project all the pedestrian accidents in this period have been analysed providing global information about a wide range of aspects, since location, driver and pedestrian characteristics, weather and road conditions, among others. In addition, 50 in-depth accidents have been investigated and the data collected according the Pendant methodology. For this in-depth methodology detailed information about the accident has been collected, including injuries, vehicle damage, road conditions and road user- behaviour and actions. An accident reconstruction has been carried for each case including the determination of the speeds and driver actions, and the analysis of the contributing factors for the accident. Depending of the accident complexity, different methodologies have been used to analyse these accident, from the classical analytical equations such as Simms and Woods, to the use of detailed computational pedestrian models as those included in the commercial software- PC-Crash-® or Madymo-®. Also one of the goals of our investigation is the development of multibody models and methodologies for the reconstruction of pedestrian accidents. Some of these tools integrated in the commercial software Cosmos Motion-® are presented. The advantages of the different approaches are compared and discussed for some of the accidents investigated. With these tools the impact speed can be determined from the projection distance with analytical tools or PC-Crash-®, but more complex tools should be used to determine speed from the injuries, what is especially important for fatal accidents. The influence of the vehicle geometry and stiffness characteristics is another aspect analysed, where the influence of the vehicle stiffness has been determined using a combined multibody-finite elements approach within the software Madymo-®.
Automotive Engineering, Mechanical Engineering and TechnologyrnAbstract: The degrees of injury severity, as a rule injuries scaled by AIS of specific regions of the human body, investigated out of road traffic accidents correspond to the body-specific loading values, which are found out with the aid of experimental or mathematical simulation of crash tests with motor vehicles or with sled tests. The coherence between the injured human being on the one hand and the physical and the theoretical model respectively on the other hand is established by the risk function, which describes the probability of degrees of injury severity in dependence on the protection criteria. Due to the different physical characteristics in the simulation, e.g. accelerations, forces, compressions and their velocity, the compilation of these quantities, comparable to the MAIS, the maximal occurred single AIS obtained in accident analysis is much more difficult in the simulation than in the accident occurrence. Therefore it is obvious to normalize the loading values gained out of simulation and to summarise them to an entire value in a suitable manner, the safety index.rn
Validation of human pedestrian models using laboratory data as well as accident reconstruction
(2007)
Human pedestrian models have been developed and improved continually. This paper shows the latest stage in development and validation of the multibody pedestrian model released with MADYMO. The biofidelity of the multibody pedestrian model has been verified using a range of full pedestrian-vehicle impact tests with a large range in body sizes (16 male, 2 female, standing height 160-192cm, weight 53.5-90kg). The simulation results were objectively correlated to experimental data. Overall, the model predicted the measured response well. In particular the head impact locations were accurately predicted, indicated by global correlation scores over 90%. The correlation score for the bumper forces and accelerations of various body parts was lower (47-64%), which was largely attributed to the limited information available on the vehicle contact characteristics (stiffness, damping, deformation). Also, the effects of the large range in published leg fracture tolerances on the predicted risk to leg fracture by the pedestrian model were evaluated and compared with experimental results. The validated mid-size male model was scaled to a range of body sizes, including children and a female. Typical applications for the pedestrian models are trend studies to evaluate vehicle front ends and accident reconstructions. Results obtained in several studies show that the pedestrian models match pedestrian throw distances and impact locations observed in real accidents. Larger sets of well documented cases can be used to further validate the models especially for specific populations as for instance children. In addition, these cases will be needed to evaluate the injury predictive capability of human models. Ongoing developments include a so-called facet pedestrian model with a more accurate geometry description and a more humanlike spine and neck and a full FE model allowing more detailed injury analysis.
This study is aimed to investigate the correlations of impact conditions and dynamic responses with the injuries and injury severity of child pedestrians by accident reconstruction. For this purpose, the pedestrian accident cases were selected from Sweden and Germany with detailed information about injuries, accident cars, and accident environment. The selected accident cases were reconstructed using mathematical models of pedestrian and passenger car. The pedestrian models were generated based on the height, weight, and age of the pedestrian involved in accidents. The car models were built up based on the corresponding accident car. The impact speeds in simulations were defined based on the reported data. The calculated physical quantities were analyzed to find the correlation with injury outcomes registered in the accident database. The reconstruction approaches are discussed in terms of data collection, estimating vehicle impact speeds, pedestrian moving speeds and initial posture, secondary ground impact, validity of the mathematical models, as well as impact biomechanics.
Detailed investigations and reconstructions of real accidents involving vulnerable road users
(2005)
The aim of this research is to improve knowledge about vulnerable road users accidents and more specifically pedestrians or cyclists. This work has been based on a complete analysis of real accidents. From accidents chosen from an in-depth multidisciplinary investigation (psychology, technical, medical), we have tried to identify the configuration of the impact: car speed, pedestrian or cyclist orientations. Then, we have made a numerical modelling of the same configuration with a multibody software. In particular, we have reproduced the anthropometry of the victim and the front shape of the car. A first simulation has been performed on this starting configuration. Next, effects of some parameters such as car velocity or victim position at impact have been numerically studied in order to find the best correlations with all indications produced by the in-depth analysis. Finally, the retained configuration was close to the presumed real accident conditions because it reproduces in particular the same impact points on the car, the same injuries, and is according to the driver statement. This double approach associating an in-depth accident analysis and a numerical simulation has been applied on pedestrian-to-car and bicyclist-tocar accidents. It has allowed us to better understand the real kinematics of such impacts. Even if this method is based on a case to case study, it underlines which parameters are relevant on a vulnerable road user accident investigation and reconstruction.
The European Union has set a target to reduce all road fatalities (over 40,000) with 50% in 2010. This target percentage remained unchanged with the introduction of the ten new member states within the EU as by May 1st, 2004. According to Eurostat, 34% of all fatalities in 1998 in the, then, fifteen states of the European Union were the result of single vehicle collisions. This represents over 14,000 lives lost each year of which many can likely be saved through better roadside infrastructure design. The challenge for road safety professionals is to find methods and design strategies that help to reduce these casualties. Procedures for full-scale vehicle crash testing of guard rails were first published in the US in 1962. Present European regulation is mainly based on these procedures and later developments. Since then the vehicle fleet has changed considerably. Due to the complexity of the actual safety problem the numerical simulation approach offers a good opportunity to evaluate the different parameters involved in road safety, such as infrastructure properties, vehicle type, vehicle occupants and injuries. The ideal situation would be that simulation tools are coupled or integrated and all involved effects would be related. At the moment this is not the case yet, but initiatives are taken and a new virtual era has started. This paper offers a method looking at two components that encompass the driving environment: the car and the guardrail. As part of the EC-funded project, RISER (Roadside Infrastructure for Safer European Roads) a multi body simulation program study is carried out to determine sensitivities of some parameters in car to guardrail collisions and gives insides in performance of the car with passive safety equipment, the guardrail and the interaction of these objects with each other. By offering a set of methods that includes these two aspects and their intertwining relations, more confidence can be gained in actually reducing fatalities due to single vehicle collisions with, or due to, roadside furniture. Reducing the number of fatalities of single vehicle crashes would contribute greatly to the stated goal of reducing casualties altogether.
In recent years the boundaries between active and passive safety blurred more and more. Passive safety in the traditional term includes all safety aspects to prevent occupants to be injured or at least injury severity should be reduced. Passive Safety starts with the collision (first vehicle contact) and ends with rescue (open vehicle doors). Within this phase the occupant has to be protected by the passenger compartment whereby no intrusion should occur. Active safety on the other side was developed to interact prior to the collision whereby the goal is to prevent accidents. The extensive interaction between active and passive safety led to the terminologies "Primary" and "Secondary" safety whereas the expression Integrated Safety Concept was generated. Within this study the most well documented single vehicle accidents with cars not equipped with ESP were identified from the PENDANT database and reconstructed. Additional cases were found in the database ZEDATU of TU Graz. In comparison each case was simulated with the assumption that the cars were equipped with ESP. The differences regarding accident avoidance or crash severity as well as reduction of injury risk were analysed.
Ziel des vorliegenden Forschungsvorhabens ist die Erarbeitung weitergehender Anforderungen an elektroakustische Anlagen in Straßentunneln unter Beachtung der technischen und wirtschaftlichen Umsetzbarkeit. Hierzu sind allgemeingültige Kriterien zu definieren, anhand derer eine elektroakustische Beschallungsanlage für Tunnel ausgelegt werden kann, ohne dass aufwändige schalltechnische Einzeluntersuchungen durchgeführt werden müssen. Aus den bereits vorliegenden Projekten wurden Ergebnisse schalltechnischer Untersuchungen aus 19 Tunneln kategorisiert und vergleichend gegenübergestellt. Es wurden folgende wesentliche Erkenntnisse gewonnen: - Die Nachhallzeiten liegen im Bereich von 5 s bis 10 s, im mittleren Bereich und für tiefe Frequenzen ansteigend bis auf 27 s. Die Nachhallzeiten typischer Tunnel unterscheiden sich nur unwesentlich. - Nachhallzeitmessungen sind daher nicht notwendig. Wichtig ist die Beurteilung der Primärstruktur eines Tunnels. - Es gibt besondere Schallleitungseigenschaften von Tunnelröhren, die durch die Reflektionen entstehen. Diese Struktur zeichnet sich durch nützliche Schallreflexionen aus, die sich für eine Sprachverständlichkeit fördernde Unterstützung nutzen lassen. Daraus lassen sich folgende akustische Anforderungen an einen für Tunnelbeschallungen geeigneten Lautsprecher formulieren: - horizontale und vertikale Abstrahlwinkel von etwa jeweils 30 bis 35-°, - Rückwärtsdämpfung von ARueck ≥ 30 dB, - Schalldruckpegel Lpmax ≥ 130 dB(SPL), - Übertragungsfrequenzgang 300Hz bis 12000 Hz. Auf Grund dieser Erkenntnisse werden Versuche in einem zur Verfügung gestellten Testtunnel mit auf dem Markt befindlichen Lautsprechersystemen durchgeführt, was zu folgenden Aussagen für die Konzeption einer Beschallungsanlage führt: - Herkömmliche Lautsprecher sind für eine Beschallung mit Sammelruf ungeeignet. - Ein nach dem Prinzip des Grenzflächenhorns entwickelter Speziallautsprecher hatte geeignete akustischen Eigenschaften. - Die Lautsprecher müssen zeitlich angepasst werden. - Eine Sprachverständlichkeit von mindestens STI ≥ 0,45 ist anforderungsgerecht. Bei Messungen in Tunneln, deren Beschallungsanlagen unter Berücksichtigung der im Forschungsvorhaben gewonnenen Erkenntnisse ausgelegt wurden, werden Sprachverständlichkeitswerte mit im Mittel STI = 0,52, 0,50 und 0,49 festgestellt. Der Originalbericht enthält als Anhang "Generalisierte Muster-Ausschreibungs-Module für ein SLASS-Beschallungssystem " Erläuterungsbericht / Technische Vorbemerkungen / Leistungs-Positionstexte". Er steht ebenfalls als Download zur Verfügung.
Ziel des Forschungsvorhabens war die Klärung der Frage, in welcher Art und Weise Einsatz und Betrieb des RQ 21 in dem Entwurf der RAL geregelt werden soll. Im Vordergrund stand die Entwicklung einer Methodik zur Abgrenzung der Einsatzlänge von Strecken mit RQ 21 unter Berücksichtigung des Verkehrsablaufs und der Verkehrssicherheit. Dabei sollte die mögliche Notwendigkeit einer Beschränkung der V(Index zul) im Vergleich zu Strecken mit Seitenstreifen erläutert werden. Weiterhin galt es zu klären, wie eine Bewertung der Verkehrsqualität auf diesem Regelquerschnitt erfolgen soll. Zunächst erfolgte eine Dokumentation von Strecken aus verschiedenen Bundesländern, um die Charakteristik bestehender Strecken im Netz zu quantifizieren. Anhand einer Voruntersuchung wurden die Kriterien für Lage und Umfang der verschiedenen Messquerschnitte festgelegt. Erhebungen zur Analyse des Fahrverhaltens wurden im Bereich der freien Strecke und an Übergängen mit verschiedenen Änderungen der Streckencharakteristik durchgeführt. Das auf Strecken mit verschiedenen Geschwindigkeitsbeschränkungen (V(Index zul)) erfasste Geschwindigkeitsverhalten wurde in q-V-Beziehungen dargestellt und für verschiedene verkehrliche Randbedingungen mittels Simulationen für den vorgesehenen Verkehrsstärkebereich abgebildet. Die Untersuchungen zeigten für Streckenzüge des RQ 21 gegenüber dem RQ 28 einen ungünstigeren Sicherheitsgrad Unfallkostenrate (UKR) wegen erhöhter \"Rate der Unfälle mit Personenschaden\" (UR(P)). Es wurde ein Ansatz entwickelt, der in Abhängigkeit der verkehrlichen und baulichen Parameter einer Strecke die mittlere Anzahl von Störungen, die auf Strecken ohne Seitenstreifen gegenüber den Strecken mit Seitenstreifen mehr auftreten, angibt. Die Empfehlungen zur Begrenzung der Einsatzlänge des RQ 21 auf eine Länge von 15 km sind das Resultat dieses Ansatzes. Grundsätzlich gilt, dass der Einsatz und Betrieb des RQ 21 an enge Rahmenbedingungen gekoppelt ist, deren Einflüsse in diesem Forschungsprojekt näher beschrieben sind.
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.
Die Verkehrssicherheit ist auf Autobahnen bei Niederschlägen, insbesondere in wasserabflussschwachen Bereichen, beeinträchtigt. Zur Überprüfung der Entwässerungsbereiche wurde im Rahmen eines Forschungsprojekts ein Simulationsmodell (PLANUS) entwickelt, mit welchem es möglich ist, aus Fahrbahn- und Trassierungsdaten sowie der Regenintensität die Wasserfilmdickenverteilungen sowie die Aquaplaninggeschwindigkeiten zu errechnen. In der Untersuchung wurden die berechneten Aquaplaninggeschwindigkeiten mit den tatsächlich gefahrenen Geschwindigkeiten auf den Autobahnen verglichen. Für 9 Messstellen wurden hierzu Analysen der Pkw-Geschwindigkeiten im freien Verkehrsfluss auf dem linken Fahrstreifen bei verschiedenen Niederschlagsintensitäten durchgeführt. Es zeigte sich, dass an 3 der 9 untersuchten Stellen die tatsächlich gefahrenen Geschwindigkeiten oberhalb der kritischen Geschwindigkeit lagen, ab der ein Aufschwimmen der Reifen auf dem Wasserfilm möglich ist. Derartige Bereiche sind auf Autobahnen vor allem dort anzutreffen, wo Querneigungswechsel in Verbindung mit großer Fahrbahnbreite und geringer Längsneigung vorkommen, das heißt, Strecken auf denen das Wasser schlecht ablaufen kann oder einen langen Weg zurücklegt. Mithilfe der Software PLANUS kann das Erfordernis von entwurfstechnischen, straßenbaulichen und verkehrstechnischen Maßnahmen zur Minderung des Unfallrisikos beurteilt werden. Ziel muss es sein, die Unfallgefahren an Abschnitten mit Aquaplaninggefahr zu reduzieren.
Neben der zunehmenden Bedeutung der aktiven Sicherheit bleiben Maßnahmen der passiven Sicherheit bei der Entwicklung moderner Kraftfahrzeuge unabdingbar. Die Weiterentwicklung von Maßnahmen zum passiven Fußgängerschutz war zunächst größtenteils durch Verbraucherschutztests wie zum Beispiel Euro NCAP oder JNCAP getrieben und ist nun auch durch gesetzliche Regelungen verpflichtend geworden. Im vorangegangenen Forschungsprojekt der BASt FE 82.229/2002 Schutz von Fußgängern beim Scheibenaufprall ist die Grundlage eines modularen Prüfverfahrens für den Kopfaufprall im Bereich der Windschutzscheibe, bestehend aus einem Versuchs- und einem Simulationsteil, erarbeitet worden. Im Rahmen dieses Projektes wurde ein hybrides Testverfahren bestehend aus Versuch und Simulation ausgearbeitet, das den Bereich der Windschutzscheibe und dabei auch crashaktive Systeme wie Airbags berücksichtigt. Das Testverfahren kombiniert Komponentenversuche mit einem Simulationsteil, in dem Fahrzeug-Fußgänger-Simulationen und lmpaktorsimulationen durchgeführt werden. Zusätzliche Dummyversuche dienten zur Bewertung des Testverfahrens. Alle erarbeiteten virtuellen und realen Testmethoden wurden an einem Referenzfahrzeug (Opel Signum), welches repräsentativ für eine durchschnittliche Mittelklasselimousine steht, durchgeführt. Das Fahrzeug wurde mit einem Airbagsystem ausgerüstet und der Testprozedur mit und ohne diesem System vergleichend unterzogen. Innerhalb dieser Untersuchungen konnte gezeigt werden, dass neue Testmethoden unter Ausnutzung von Simulationen und Komponententests es erlauben, realistischere Versuchsbedingungen unter Berücksichtigung von potenziellen Kopfaufprallpositionen und -zeiten zu definieren. Dabei können sehr gute Übereinstimmungen zwischen Fußgängersimulation und Dummyversuch erreicht werden. Die Randbedingungen für den Kopfaufprall und die Aufprallzeit wurden durch den Einsatz von Fußgängermodellen ermittelt. Weiterhin ermöglichen die Simulationen, zusätzliche Einflussdaten wie Vektoren mit den Kopfaufprallgeschwindigkeiten und -winkeln zu bestimmen.
The German Federal Ministry of Economics and Technology is funding a projectrncalled "Leistra2" with the aim of understanding the tire road contact and to find measures to reduce traffic noise, in particular to reduce the noise of tires rolling on pavements, i.e. tire-road noise. The project is composed out of three mayor subjects, low noise tires, low noise pavements and verification of the results, each made out of single sub-projects. The purpose of this paper is to give a survey about Leistra2 and to report about the latest activities and results. More detailed information and contact data of the partners involved can be found at http://www. LeiStra2.de. The program is the successor of the program LeiStra (Leiser Strassenverkehr), dealing with similar topics.rn
Abstract: Für Kinder in Deutschland existiert im Pkw weiterhin ein höheres Risiko, im Straßenverkehr bei einem Unfall schwer verletzt oder getötet zu werden, als es für ungeschützte Verkehrsteilnehmer wie Fahrradfahrer oder Fußgänger besteht. Dies erscheint auf den ersten Blick nicht nachvollziehbar, da der Pkw und die vorgeschriebenen Kindersitze den Kindern eine hohe Sicherheit bieten müssten. Der vorliegende Projektbericht gibt Aufschluss über den aktuellen Stand der Sicherheit von Kindern im Pkw in Deutschland und zeigt Optimierungspotenzial auf. Die Schutzwirkung der Kindersitze hängt von mehreren Faktoren ab. Dabei stehen technische Aspekte, die hier detailliert untersucht wurden, im Vordergrund. Doch vor allem in den letzten Jahren zeigte sich immer wieder in Feldstudien, aber auch in der Unfallanalyse, dass Kinderschutzsysteme (KSS) oftmals nicht nach den Vorgaben installiert wurden. Wenn der Kindersitz und/oder das Kind nicht entsprechend der Bedienungsanleitung gesichert werden, kann sich das Schutzpotenzial der KSS reduzieren und gegen Null gehen. Im schlimmsten Fall stellt eine fehlerhafte Benutzung von KSS eine Gefahr sowohl für das Kind als auch für andere Pkw-Insassen dar. Die Unfallanalyse ergab keine Aussage darüber, ob verschiedene KSS-Modelle zu unterschiedlichen Verletzungsmustern führen, da die Unfallkonstellationen pro KSS-Modell zu verschieden waren. Des Weiteren wurde analysiert, inwieweit heutige Testverfahren mit diesen Konstellationen übereinstimmen. Das Ziel, mit wenigen Verfahren möglichst alle relevanten Unfälle abzubilden, wurde zum Teil ereicht. Zu viele Testverfahren mit unterschiedlichen Bewertungssystemen stellen heutzutage die Endverbraucher vor das Problem, dass nicht klar ist, welches KSS wirklich das beste ist. In der Realität hängt die Schutzwirkung zudem noch wesentlich von der KSS-Pkw-Kombination ab, die nur annähernd durch Versuche überprüft werden kann, da sich eine zu hohe Anzahl von Kombinationsmöglichkeiten ergibt. Anhand von mehr als 100 Versuchen wurde das Schutzpotenzial von verschiedenen aktuellen Kindersitzmodellen untersucht. Dabei wurden immer vermeintlich gute und schlechte KSS gegenübergestellt und unter gleichen Randbedingungen getestet. Ziel dieses Vorgehens war es, anhand der Messergebnisse Maßnahmen zu erkennen, die dem Schutz der Kinder dienlich sind. Zusammenfassend kann gesagt werden, dass prinzipiell für Kinder ein gutes Schutzniveau durch KSS besteht, was aber von KSS zu KSS verschieden sein kann. Die teureren KSS wiesen keine mechanische Zerstörung auf und überstanden alle Tests ohne ernsthafte Beschädigungen. Lediglich das oftmals als Dämpfungsmaterial eingesetzte Polystyrol nahm Energie auf und verformte sich wie vorgesehen plastisch. Bei den "Billig-Kindersitzen" ergab sich leider ein komplett anderes Bild. Sobald die Anforderungen über die der Gesetzgebung hinausgehen, ist immer weniger Schutz für die Kinder vorhanden. Besonders im Seitenaufprall offenbarten sich erhebliche Lücken in der Sicherheit. Dies reichte von mechanischem Versagen mancher Plastikteile bis hin zu konstruktiven Unzulänglichkeiten. Vor allem die Gurtführung muss deutlicher gekennzeichnet und mechanisch verstärkt werden. Trotz des hohen Schutzpotenzials einiger Kindersitze ist das Ende der Entwicklung noch nicht abzusehen. In allen Kindersitzklassen ist es prinzipiell möglich, die Belastungswerte weiter zu reduzieren. Dazu werden am Ende des Berichtes verschiedene Möglichkeiten aufgezeigt. Zum einen ist dies eine optimierte Babyschale, die durch eine Trägheitsbewegung gezielt Energie abbaut und das Baby in eine günstigere Position bringt, in der die Belastungen des Körpers reduziert sind. Zum anderen wird gezeigt, dass durch die feste Anbindung des KSS an den Pkw und die Reduzierung der Rotation um die Y-Achse die Belastungen für Kinder reduziert werden können. Größtes Entwicklungspotenzial bietet dabei das ISOFIX-System. Es ist bekannt, dass ISOFIX die Fehlbedienung des Kindersitzes und die Belastungen der Kinder deutlich reduzieren kann. Trotzdem ist die bisherige Marktdurchdringung von ISOFIX eher gering. Obwohl insgesamt ein positives Fazit gezogen werden kann, darf nicht aufgehört werden, die Kindersicherheit weiter zu verbessern. Denn nicht alle Kindersitze schützen heute gleich gut. Einige genügen lediglich den Gesetzesansprüchen und finden in vielen Fällen durch einen sehr geringen Verkaufspreis Zugang in die Pkw. Durch verschärfte Testbedingungen sollten diese Kindersitze abgeschafft und der Weg für neue und bessere Kinderschutzsysteme frei gemacht werden.