Bone fracture patterns could be crucial in reconstructing the nature of loading, especially in the lower limb and upper limb kinematics in vehicle-pedestrian crashes. In addition, use of FE bone models can be a handy tool to predict vehicle impact velocity and the impact direction. The point of fracture initiation in bone loading has been predicted quite accurately earlier. A methodology that predicts bone crack initiation and its propagation pattern for the six known loading directions using a single material and failure model is presented.
Pedestrian and cyclist are the most vulnerable road users in traffic crashes. One important aspect of this study was the comparable analysis of the exact impact configuration and the resulting injury patterns of pedestrians and cyclists in view of epidemiology. The secondary aim was assessment of head injury risks and kinematics of adult pedestrian and cyclists in primary and secondary impacts and to correlate the injuries related to physical parameters like HIC value, 3ms linear acceleration, and discuss the technical parameter with injuries observed in real-world accidents based documented real accidents of GIDAS and explains the head injuries by simulated load and impact conditions based on PC-Crash and MADYMO. A subsample of n=402 pedestrians and n=940 bicyclists from GIDAS database, Germany was used for preselection, from which 22 pedestrian and 18 cyclist accidents were selected for reconstruction by initially using PC-Crash to calculate impact conditions, such as vehicle impact velocity, vehicle kinematic sequence and throw out distance. The impact conditions then were employed to identify the initial conditions in simulation of MADYMO reconstruction. The results show that cyclists always suffer lower injury outcomes for the same accident severity. Differences in HIC, head relative impact velocity, 3ms linear contiguous acceleration, maximum angular velocity and acceleration, contact force, throwing distance and head contact timing are shown. The differences of landing conditions in secondary impacts of pedestrians and cyclists are also identified. Injury risk curves were generated by logistic regression model for each predicting physical parameters.
The accident research of Hanover and (from 1999 on) Dresden registered 736 leg injuries (AIS ≥ 2) from 1983 to March 2007. 174 of these injuries (23.6 %) were fractures or dislocations of foot and ankle. 149 feet of 141 front seat car occupants in 140 cars were affected. Of these 117 were drivers, 24 were front seat passengers. The mean age of occupants was 38.5 -± 16.8 years. Ankle fractures were the most frequent injury (n = 82; 80 malleolar fractures, 2 pilon fractures). 34 fractures and dislocations affected the hindfoot (5 talus and 26 calcaneal fractures, 2 subtalar dislocations and 1 subtotal amputation) , 16 to midfoot (4 navicular fractures, 5 cuboid fractures, 3 fractures of cuneiformia, 2 dislocations of chopart joint, 1 subtotal amputation, and one severe decollement) and 39 the forefoot (metatarsal fractures). Open fractures were seldom seen (2 malleolar fractures, 1 metatarsal fracture). Both feet were injured in 10 cases. 33 occupants (23.4 %) were polytaumatic had a polytrauma, 17 of them died. 81 percent of the occupants were belted. The cars were divided in pre EuroNCAP (year of manufacture 1997 and older) and post EuroNCAP cars (year of manufacture 1998 and newer). Most of the foot injuries were seen in pre EuroNCAP cars. Most of the occupants sat in compact cars (40 drivers and 9 front seat passengers) and large family cars (27 drivers and 7 co-drivers). 49 of 140 accidents occurred on country roads, 26 on main roads and 13 on motorways. The crash direction was mostly frontal. Generally were found no differences of delta v- and EES-level between the injured foot regions, but divided into pre- and post-EuroNCAP cars there was a tendency to higher delta v- and EES-levels in newer cars. The frequency of foot injuries increased linearly with increasing delta v-level; but above delta v-level of 55 km/h the linear increase only was seen in pre-EuroNCAP cars, post-EuroNCAP cars showed no further increase of injuries. The footwell intrusion showed no difference between the injured foot regions but pre-EuroNCAP cars had a tendency to higher footwell intrusion. There were no differences in footwell intrusion between the car types. Only 29 of 174 fractures or dislocations of foot were seen in post-EuroNCAP cars, the predominate number of these injuries (n = 145) were noticed in pre-EuroNCAP cars. A lower probability of long-term impairment was found in post-EuroNCAP cars for equal delta v levels, using the AIS2008 associated Functional Capacity Index (FCI) for the foot region.
Recent findings from real-world accident data have shown that fatality risks for pedestrians are substantially lower than generally reported in the traffic safety literature. One of the keys to this insight has been the large and random sample of car-to-pedestrian crashes available in the German In-Depth Accident Study (GIDAS). Another key factor has been the proper use of weight factors in order to adjust for outcome-based sampling bias in the accident data. However, a third factor, a priori of unknown importance, has not yet been properly analysed. This is the influence of errors in impact speed estimation. In this study, we derived a statistical model of the impact speed errors for pedestrian accidents present in the GIDAS database. The error model was then applied to investigate the effect of the estimation error on the pedestrian fatality risk as a function of car impact speed. To this end, we applied a method known as the SIMulation-EXtrapolation (SIMEX) method. It was found that the risk curve is fairly tolerant to some amount of random measurement error, but that it does become flattened. It is therefore important that the accident investigations and reconstructions are of high quality to assure that systematic errors are minimised and that the random errors are under control.
The aim of this study was to evaluate the performance and accuracy of Event Data Recorders (EDRs). The analysis was based on J-NCAP crash tests from 2006"2007, with the corresponding EDR datasets. The pre-crash velocity, maximum delta-V and delta-V versus time history data recorded in the EDRs were compared with the reliable crash test data. The difference between the EDR pre-crash velocity and the laboratory test speed was less than 4 percent. In contrast, in several cases the maximum delta-V and delta-V versus time history data obtained from the EDRs showed uncertainty of measurement in comparisons with the reliable delta-V data. The difference in maximum delta-V in these comparisons was more than 5 percent in 10 of 14 tests and more than 10 percent in 4 of 14 tests. The EDRs underestimated the maximum delta-V in almost all tests. It was also concluded that the calculated acceleration from the EDR delta-V versus time history data showed good agreement with the instrumented accelerometer signal during the collision in almost all tests.
In a first step, we have examined approximately 23 000 single vehicle accidents within the Austrian National Statistics database. In a second step, we considered 15% of all fatal "running off the road" accidents that occurred in Austria in 2003. As a result, two accident categories were specified; "leaving the road without preceding manoeuvre" and "leaving the road with preceding manoeuvre". These two categories can be basically characterised by the vehicle- heading angle and its velocity angle. In this report, we further suggest theoretical approaches for the dimensioning of a safety zone, an area adjacent to the road free of fixed objects or dangerous slopes. We also show the link between the two accident categories mentioned above and the real world accidents analysed in detail. These observations also form the basis for the required length for safety devices. Finally, we summarise accident avoidance strategies.
Methods for analyzing the efficiency of primary safety measures based on real life accident data
(2009)
Primary safety measures are designed to help to avoid accidents or, if this is not possible, to stabilize respectively reduce the dynamics of the vehicle to such an extent that the secondary safety measures are able to act as good as possible. The efficiency of a primary safety measure is a criterion for the effectiveness, with which a system of primary safety succeeds in avoiding or mitigation the severity of accidents within its range of operation and in interactionwith driver and vehicle. Based on Daimler-´s philosophy of the "Real Life Safety" the reflection of the real world accidents in the systems range of operation is both starting point as well as benchmark for its optimization. This paper deals with the methodology to perform assessments of statistical representative efficiency of primary safety measures. To be able to carry out an investigation concerning the efficiency of a primary safety measure in a transparent and comparable way basic definitions and systematics were introduced. Based on these definitions different systematic methods for estimating efficiency were discussed and related to each other. The paper is completed by presenting an example for estimating the efficiency of actual "single" and "multi" connected primary safety systems.
Pedestrian accidents are one of the major concerns related with road accidents around the world. Portugal has one of the highest rates of pedestrian fatalities in Europe. In this paper an overview conditions were the pedestrian accidents occurred in Portugal is presented. In the last years, a project related with the pedestrian accidents has run in Portugal for the period 2004-2006 where 603 people died, 2097 have been severely injured and about 17000 slightly injured. Within this project all the pedestrian accidents in this period have been analysed providing global information about a wide range of aspects, since location, driver and pedestrian characteristics, weather and road conditions, among others. In addition, 50 in-depth accidents have been investigated and the data collected according the Pendant methodology. For this in-depth methodology detailed information about the accident has been collected, including injuries, vehicle damage, road conditions and road user- behaviour and actions. An accident reconstruction has been carried for each case including the determination of the speeds and driver actions, and the analysis of the contributing factors for the accident. Depending of the accident complexity, different methodologies have been used to analyse these accident, from the classical analytical equations such as Simms and Woods, to the use of detailed computational pedestrian models as those included in the commercial software- PC-Crash-® or Madymo-®. Also one of the goals of our investigation is the development of multibody models and methodologies for the reconstruction of pedestrian accidents. Some of these tools integrated in the commercial software Cosmos Motion-® are presented. The advantages of the different approaches are compared and discussed for some of the accidents investigated. With these tools the impact speed can be determined from the projection distance with analytical tools or PC-Crash-®, but more complex tools should be used to determine speed from the injuries, what is especially important for fatal accidents. The influence of the vehicle geometry and stiffness characteristics is another aspect analysed, where the influence of the vehicle stiffness has been determined using a combined multibody-finite elements approach within the software Madymo-®.
There is a need for detecting characteristics of pedestrian movement before car-pedestrian collisions to trigger a fully reversible pedestrian protection system. For this purpose, a pedestrian sensor system has been developed. In order to evaluate the effectiveness of the sensor system, the in-depth knowledge of car-pedestrian impact scenarios is needed. This study aims at the evaluation of the sensor system. The accident data are selected from the STRADA database. The accident scenarios available in this database were evaluated and the knowledge of the most common scenarios was developed in terms of the pedestrian trajectory, the pedestrian speed, the car trajectory, the car velocity, etc. A mathematical model was then established to evaluate the sensor system with different detective angles. It was found that in order to detect all the pedestrians in the most common scenarios on time the sensor detective angle must be kept larger than 60 degrees.
Description of road traffic related knee injuries in published investigations is very heterogeneous. The purpose of this study was to estimate the risk of knee injuries in real world car impacts in Germany focusing vulnerable road users (pedestrians, bicyclists and motorcyclists) and restrained car drivers. The accident research unit analyses technical and medical data collected shortly after the accident at scene. Two different periods (years 1985-1993 and 1995-2003) were compared focusing on knee injuries (Abbreviated Injury Scale (AISKnee) 2/3). In order to determine the influences type of collision, direction and speed as well as the injury pattern and different injury scores (AIS, MAIS, ISS) were examined. 1.794 pedestrians, 742 motorcyclists, 2.728 bicyclists and 1.116 car drivers were extracted. 2% had serious ligamentous or bony injuries in relation to all injured. The risk of injury is higher for twowheelers than for pedestrians, but knee injury severity is higher for the latter group. Overall the current knee injury risk is low and significant reduced comparing both time periods (27%, p<0,0001). Severe injuries (AISKnee 2/3) were below 1%). Improved aerodynamic design of car fronts reduced the risk for severe knee injuries significantly (p=0,0015). Highest risk of injury is for motorcycle followed by pedestrians, respectively. Knee protectors could prevent injuries by reducing local forces. The classically described dashboard injury was rarely identified. The overall injury risk for knee injuries in road traffic is lower than estimated and reduced comparing both periods. The aerodynamic shape of current cars compared to older types reduced the incidence and severity of knee injuries. Further modification and optimization of the interior and exterior design could be a proper measurement. Classic described injury mechanisms were rarely identified. It seems that the AIS is still underestimating extremity injuries and their long term results.
Neben der zunehmenden Bedeutung der aktiven Sicherheit bleiben Maßnahmen der passiven Sicherheit bei der Entwicklung moderner Kraftfahrzeuge unabdingbar. Die Weiterentwicklung von Maßnahmen zum passiven Fußgängerschutz war zunächst größtenteils durch Verbraucherschutztests wie zum Beispiel Euro NCAP oder JNCAP getrieben und ist nun auch durch gesetzliche Regelungen verpflichtend geworden. Im vorangegangenen Forschungsprojekt der BASt FE 82.229/2002 Schutz von Fußgängern beim Scheibenaufprall ist die Grundlage eines modularen Prüfverfahrens für den Kopfaufprall im Bereich der Windschutzscheibe, bestehend aus einem Versuchs- und einem Simulationsteil, erarbeitet worden. Im Rahmen dieses Projektes wurde ein hybrides Testverfahren bestehend aus Versuch und Simulation ausgearbeitet, das den Bereich der Windschutzscheibe und dabei auch crashaktive Systeme wie Airbags berücksichtigt. Das Testverfahren kombiniert Komponentenversuche mit einem Simulationsteil, in dem Fahrzeug-Fußgänger-Simulationen und lmpaktorsimulationen durchgeführt werden. Zusätzliche Dummyversuche dienten zur Bewertung des Testverfahrens. Alle erarbeiteten virtuellen und realen Testmethoden wurden an einem Referenzfahrzeug (Opel Signum), welches repräsentativ für eine durchschnittliche Mittelklasselimousine steht, durchgeführt. Das Fahrzeug wurde mit einem Airbagsystem ausgerüstet und der Testprozedur mit und ohne diesem System vergleichend unterzogen. Innerhalb dieser Untersuchungen konnte gezeigt werden, dass neue Testmethoden unter Ausnutzung von Simulationen und Komponententests es erlauben, realistischere Versuchsbedingungen unter Berücksichtigung von potenziellen Kopfaufprallpositionen und -zeiten zu definieren. Dabei können sehr gute Übereinstimmungen zwischen Fußgängersimulation und Dummyversuch erreicht werden. Die Randbedingungen für den Kopfaufprall und die Aufprallzeit wurden durch den Einsatz von Fußgängermodellen ermittelt. Weiterhin ermöglichen die Simulationen, zusätzliche Einflussdaten wie Vektoren mit den Kopfaufprallgeschwindigkeiten und -winkeln zu bestimmen.
In spite of today's highly sophisticated crash test procedures like the different NCAP programs running world-wide, bad real world crash performance of cars is still an issue. There are crash situations which are not sufficiently represented by actual test configurations. This is especially true for car to car, as well as for car to object impacts. The paper describes reasons for this bad performance. The reasons are in principal bad structural interaction between the car and its impact partners (geometric incompatibility), unadjusted front end stiffness (stiffness incompatibility) and collapse of passenger compartments. To show the efficiency of improving cars' structural behaviour in accidents with different impact partners an accident data analysis has been taken out by members of European Project VC-COMPAT. Accident data analysis has shown that in Germany between 15,000 and 20,000 of the now severely injured car occupants might get less injured and between 600 and 900 car occupant fatalities might be saved. Similar results arise for the UK.
Die Verordnungsgeber haben länderübergreifende Normen und Vorschriften für die Durchführung und Auswertung von Crashversuchen mit Personenkraftwagen bei verschiedenen Aufprallarten entwickelt, die im Rahmen der Entwicklung und Zulassung neuer Fahrzeuge Anwendung finden. Verbraucherschutzorganisationen, Automobilclubs und Fachzeitschriften tragen mit der Durchführung und Publikation eigener Tests dazu bei, dass die passive Sicherheit von Personenkraftwagen in der breiten Öffentlichkeit mehr und mehr beachtet wird. Im Gegensatz dazu ist die Durchführung von Crashtests zur Untersuchung und Bewertung der passiven Sicherheit von Motorrädern relativ neu. Vor diesem Hintergrund hat die Bundesanstalt für Straßenwesen das vorliegende Forschungsprojekt vergeben. Hierbei waren unter Verwendung geeignet erscheinender Prüfverfahren reale Unfallsituationen nachzubilden. Unter Beachtung der Vielfalt der motorisierten Zweiräder mit ihrer Einteilung in verschiedene Zulassungs-Kategorien und zugehöriger Unfalldaten wurde das reale Unfallgeschehen analysiert. Neben Daten aus der amtlichen Unfallstatistik wurden dabei Informationen aus der Literatur und eigene Erhebungen ausgewertet. Ergänzend ist der aktuelle Kenntnisstand zur Biomechanik aufbereitet worden. Eine Beschreibung des Status quo der passiven Motorradsicherheit erfolgte unter Analyse der hierbei relevanten Elemente, Baugruppen und Eigenschaften des Motorrades. Dazu gehören Lenker, Sitzbank, Fußrasten, Tank, Verkleidung, Airbag (noch nicht im Hersteller-Angebot), Vorderradgabel und Standrohre sowie die Aufsassen-Kopfhöhe. Weiterhin gingen die Ergebnisse von Full-Scale-Crashtests, die im internationalen Standard ISO 13232 beschrieben sind, mit Anstößen von Motorrädern an der Seite von Personenkraftwagen in die Darstellung des Status quo der passiven Motorradsicherheit ein. Zusätzlich wurden im Rahmen des Forschungsprojektes Schlittenversuche durchgeführt. Ein zur Darstellung des rechtwinkligen Motorradanpralles an der Seite eines stehenden Personenkraftwagens geeigneter Schlitten ist im Rahmen des Projektes entworfen, realisiert und eingesetzt worden. In der Literatur beschriebene Motorrad-Sicherheitskonzepte und Vorschläge für besondere Motorrad-Sicherheitselemente sind ebenfalls dargestellt worden. Im Rahmen des Forschungsprojektes wurde ein umfassender Ansatz verfolgt. Er enthält die Bewertung von Sicherheitsmerkmalen, die aus technischen Beschreibungen entnommen und am stehenden Fahrzeug ermittelt werden können (Primärdaten) sowie die Ergebnisse von dynamischen Crash- und Schlittentests (Sekundärdaten). Dabei erfolgt stets die Orientierung am realen Unfallgeschehen (Tertiärdaten). Der internationale Standard ISO 13232 wird als geeigneter Ausgangspunkt eines umfassenden Prüf- und Bewertungsverfahrens für die passive Sicherheit motorisierter Zweiräder erkannt. Zur Erweiterung der bereits definierten Testverfahren werden Schlittentests vorgeschlagen. Außerdem werden Alleinunfälle des Motorrades zu beachten sein. Die Ergebnisse des Forschungsprojektes tragen dazu bei, die Aspekte der passiven Sicherheit von motorisierten Zweirädern zu objektivieren.
Straßenseitige Fahrzeug-Rückhaltesysteme haben entsprechend der Richtlinie für passiven Schutz an Straßen durch Fahrzeug-Rückhaltesysteme (RPS) die Aufgabe, die Folgen von Verkehrsunfällen so gering wie möglich zu halten. Sie kommen dabei sowohl zum Schutz unbeteiligter Personen, des Gegenverkehrs bei zweibahnigen Straßen sowie schutzbedürftiger Bereiche neben der Straße als auch zum Schutz der Fahrzeuginsassen vor schweren Folgen infolge Abkommens von der Fahrbahn zum Einsatz. Vor dem Einsatz der unterschiedlichen Systeme muss die Wirksamkeit des jeweiligen Systems für den entsprechenden Anwendungsfall nachgewiesen werden. Dabei regeln die RPS, welche Anforderungen an welchen örtlichen Gegebenheiten erfüllt sein müssen. In DIN EN 1317 sind die zugehörigen Prüfverfahren beschrieben. Da ein normiertes Prüfverfahren nicht alle real auftretenden Unfallszenarien abdecken kann, stellte sich die Frage, wie sich Stahlschutzplanken und Betonschutzwände beim großwinkligen Anprall kleiner und leichter Fahrzeuge verhalten und wie es um die Insassensicherheit bestellt ist. Eine im Rahmen des resultierenden Forschungsprojektes durchgeführte Analyse des Unfallgeschehens ergab für das Jahr 2007 die Zahl von 25.038 polizeilich registrierten Unfällen mit Anprall gegen eine Schutzeinrichtung [Statistisches Bundesamt]. Angaben zu Anprallwinkel, Kollisionsgeschwindigkeit und Fahrzeugmasse können dieser Statistik nicht entnommen werden. Für die In-depth-Analyse wurden daher 69 Unfallgutachten zu Kollisionen mit großem Anprallwinkel (≥ 25-°) aus der DEKRA-Unfalldatenbank herangezogen. Der Schwerpunkt wurde dabei auf 39 Unfälle gelegt, die sich auf Bundesautobahnen ereignet hatten. Mit zunehmendem Anprallwinkel nahm die Unfallhäufigkeit ab. Der größte Winkel lag bei 60-°. Die Masse der anprallenden Fahrzeuge lag zwischen 750 kg und 1.935 kg. Auffällig war die Häufung von Schleuderunfällen. In 29 Fällen kam es zu einem prekollisionären Schleudervorgang. Die Analyse des Unfallgeschehens hat so gezeigt, dass Anpralle gegen passive Schutzeinrichtungen auf Bundesautobahnen mit zunehmendem Anprallwinkel seltener werden und dass der in der Norm für die Systemprüfung geforderte Maximalwinkel von 20-° das Gesamtunfallgeschehen sehr gut abdeckt. Auf Basis der gewonnenen Ergebnisse erfolgte die Festlegung einer Crash-Test-Konfiguration zur Erlangung von Erkenntnissen über die Insassensicherheit bei großwinkligen Anprallen. Dabei wurde als Grundlage der Anprallversuch TB 11 verwendet, wobei der Anprallwinkel von 20-° auf 45-° erhöht wurde. Die Kollisionsgeschwindigkeit von 100 km/h sowie die Fahrzeugmasse von 900 kg blieben unverändert. Die Anpralltests erfolgten gegen eine simulierte Ortbetonwand sowie gegen eine Stahlschutzplanke vom Typ Super-Rail-®. Die Versuchsfahrzeuge waren typgleich mit den Modellen, die für die ursprüngliche TB-11-Prüfung der Systeme verwendet wurden. Die Versuche haben gezeigt, dass beide Systeme die Rückhaltung der anprallenden Fahrzeuge sicher gewährleisteten. Für die Fahrer beider Fahrzeuge hätte aber keine Überlebenschance bestanden. Über das Schutzniveau der Fahrzeuginsassen entscheiden bei derartigen Anprallkonstellationen letztendlich das Niveau der passiven Sicherheit der anprallenden Fahrzeuge sowie das Energieabsorptionsvermögen der die Fahrgastzelle umschließenden Strukturen.