Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (337) (entfernen)
Schlagworte
- Conference (253)
- Konferenz (252)
- Accident (137)
- Unfall (137)
- Germany (134)
- Deutschland (131)
- Injury (101)
- Verletzung (100)
- Unfallrekonstruktion (73)
- Analyse (math) (61)
In road traffic accidents, a car-seat and its occupant can be subjected to various crash pulses in the case of a rear impact. This study investigates the influence of crash pulse shape on seat-occupant response and evaluates the corresponding risk of whiplash injury. For this purpose, a rigorously validated seat-occupant system model is used to study different carseat designs and crash pulses. Two different car-seat concepts are also presented which can effectively mitigate whiplash injury for a wide range of crash severity. It is shown that for crash pulses of similar severity, the level of whiplash-risk depends strongly on the combined effects of seat design and crash pulse shape.
The objectives of this paper are the analysis of the accident risk of drivers brain pathologies (Mild Cognitive Impairment, Alzheimer- disease, and Parkinson- disease), and the investigation of the impact of driver distraction on the accident risk of patients with brain pathologies, through a driving simulator experiment. The three groups of patients are compared to a healthy group of similar demographics, with no brain pathology. In particular, 125 drivers of more than 55 years old (34 "controls"" and 91 "patients") went through a large driving simulator experimental process, in which incidents were scheduled to occur. They drove in rural and urban areas, in low and high traffic volumes and in three distraction conditions (undistracted driving, conversation with a passenger and conversation through a mobile phone). The statistical analyses indicated several interesting findings; brain pathologies affect significantly accident risk and distraction affects more the groups of patients than the control one.
Since its creation in 2011 the Pre-Crash-Matrix (PCM) offers the possibility to observe the pre-crash phase until five seconds before crash for a wide range of accidents. Currently the PCM contains more than 8.000 reconstructed accidents out of the GIDAS (German In-Depth Accident Study) database and is enlarged continuously by more than 1.000 cases per year. Hence, a detailed investigation of active safety systems in real accident situations has been made feasible. The PCM contains all relevant data in database format to simulate the pre-crash phase until the first collision of the accident for a maximum of two participants. This includes the definition of the participants and their characteristics, the dynamic behavior of the participants as time-dependent course for five seconds before crash as well as the geometry of the traffic infrastructure. The digital sketch of the accident and information from GIDAS as well as from supplementary databases represent the main input for the simulation of the pre-crash phase of an accident with the VUFO simulation model VAST (Vufo Accident Simulation Tool). This simulation in turn embodies the foundation of the PCM. The PCM underlies continual improvements and enhancements in consultation with its users. In addition to collisions of cars with other cars, pedestrians, bicycles and motorcycles the PCM now also covers car to object and car to truck collisions. The paper illustrates car to truck collisions as a showcase and explains perspectives for further developments. In 2016 a more detailed definition of the contour of the vehicle was added. Furthermore, the geometrical surroundings of the accident site will be provided in a new structure with a higher level of detail. Thus, a precise classification of road marks and objects is possible to further improve the support of developing and evaluating ADAS. This paper gives an overview about the latest developments of the PCM with its innovations and provides an outlook to upcoming enhancements. Besides potential areas of application for the development of ADAS are shown.
Automated driving will provide many kinds of benefits - some direct and some indirect. The benefits originate at the individual level, from changes in the behaviour of drivers and travellers with regard to driving and mobility, ending up with benefits at the social level via changes in the whole transport system and society, where many of the current planning and operations paradigms are likely to be transformed by automated driving. There may also be disbenefits, particularly at a social level, for example in intensity of travel which could result in additional congestion and increased use of natural resources. There may also be unintended consequences. For example, we do not know the impacts on public transport: driverless vehicles could provide a means to a lower cost service provision, but the availability of automated cars could lead to more car travel at the expense of collective transport.
Established in 1997, the European New Car Assessment Programme (Euro NCAP) provides consumers with a safety performance assessment for the majority of the most popular cars in Europe. Thanks to its rigorous crash tests, Euro NCAP has rapidly become an important driver safety improvement to new cars. After ten years of rating vehicles, Euro NCAP felt that a change was necessary to stay in tune with rapidly emerging driver assistance and crash avoidance systems and to respond to shifting priorities in road safety. A new overall rating system was introduced that combines the most important aspects of vehicle safety under a single star rating. The overall rating system has allowed Euro NCAP to continue to push for better fitment and higher performance for vehicles sold on the European market. In the coming years, the safety rating is expected to play an important role in the support of the roll-out of highly automated vehicles.
Various kinds of demerit point systems have been developed and implemented in European countries, aimed at tackling repeat offences in road transport by acting as a deterrent and providing sanctioning. The impact of a demerit point system on the number of crashes is often reported to be significant, but temporary. The objective of the EU BestPoint project was to establish a set of recommended practices that would result in a more effective and sustainable contribution of demerit point systems to road safety. A high actual chance of losing the licence and a high perceived chance of losing the licence are basic prerequisites for the effective operation of demerit point systems. For measures applied within the context of a demerit point system, a four-step-approach is recommended: warning letter, driver improvement course, licence withdrawal, rehabilitation course. Further recommendations concern issues like points and offences, e.g. which offences should lead to points, target groups, and the administration of demerit point systems. The final result of the EU BestPoint project is a handbook (van Schagen & Machata, 2012) which provides a concise overview of all recommended practices. The presentation/paper outlines how sustainable safety improvements can be achieved if national demerit point systems are implemented and maintained according to the recommended practices. In addition, potential further steps towards an EU-wide demerit point system (cross-border exchange on points and/or offences) are presented.
During the last 5 years, the number of cars fitted with side airbags has dramatically increased. They are now standard equipment, even on many smaller cars or less luxurious vehicles. While some side airbags offer thoracic protection alone, there are those that combine thoracic and head protection (of which most deploy from the seat). Other systems employ separate airbags for head and thorax protection, which are designed to be effective noticeably in a crash against a pole. This paper proposes an evaluation of the effectiveness of side airbags in preventing thoracic injuries to passenger car occupants involved in side crashes. First, the target population (who can take benefit of side airbag deployment and in what circumstances) is defined. Side airbags can be especially effective in cases of impacts on the door with intrusion at a certain impact speed. Then, an example case of a side impact with side airbag deployment is given were side airbag deployment is thought to have had a positive effect on injury outcome. A further case is presented where the impact configuration is likely to have reduced the effect of side airbag deployment on injury outcome. Finally, the estimation of side airbag effectiveness (in terms of additional occupant protection brought exclusively by the airbag) is proposed by comparing injury risk sustained by occupants in (more or less) similar cars (fitted or non fitted with airbags) because, during these years, car structure, and side airbag conception have considerably evolved. In-depth accident data from France, the UK and Germany has been collected. Out of 2,035 side impact accident cases available in the databases, we selected 435 occupants of passenger cars (built from 1998 onwards) involved in an injury accident between year 1998 and year 2004 for EES (Energy Equivalent Speed) values between 20km/h and 50km/h. The occupants, belted or not, were sat on the struck side, whatever the obstacle and type of accidents (intersection, loss of control, etc.). For multiple impact crashes, the side impact is assumed to be the more severe one. Passenger cars were fitted with (96) or without (339) side airbags. Most of the potential risk explanatory variables were correctly and reliably reported in the databases (velocity " impact zone " impact angle " occupant characteristics, etc.). The analysis compared injury risks for different levels of EES and different types of side airbags. A logistic regression model was also computed with injury variables (such as thoracic AIS 2+ or AIS 3+) as the dependant variable and other variables (including airbag type and EES) as explanatory injury risk factors. Results revealed statistically non-significant reductions in thoracic AIS 2+ and AIS 3+ injury risk in side airbag equipped cars in the impact violence range selected (odds ratio between 0.84 and 0.98 depending on types of airbags). The results are discussed. The non-significance is assumed to be due to a low number of cases. Statistical analysis for head injuries was not possible due to the low number of accident cases with passenger cars fitted with head airbags in the databases. Moreover, the discrepancies between the data coming from different countries (especially calculation of EES) might have introduced instability in the analysis.
This study is aimed to investigate the correlations of impact conditions and dynamic responses with the injuries and injury severity of child pedestrians by accident reconstruction. For this purpose, the pedestrian accident cases were selected from Sweden and Germany with detailed information about injuries, accident cars, and accident environment. The selected accident cases were reconstructed using mathematical models of pedestrian and passenger car. The pedestrian models were generated based on the height, weight, and age of the pedestrian involved in accidents. The car models were built up based on the corresponding accident car. The impact speeds in simulations were defined based on the reported data. The calculated physical quantities were analyzed to find the correlation with injury outcomes registered in the accident database. The reconstruction approaches are discussed in terms of data collection, estimating vehicle impact speeds, pedestrian moving speeds and initial posture, secondary ground impact, validity of the mathematical models, as well as impact biomechanics.
The current Brussels EU Regulation No. 1235/2011, valid from May 30, 2012, has introduced an European Tyre Label with wet grip index G classes from A to G for passenger car tyres C1, light commercial vehicles tyres C2 and heavy truck- and bus tyres C3. Every wet grip class for each vehicle category has a defined band of numerical values for the wet grip index G. The legislated wet grip values G in this EU- Regulation are very low. The measured braking distances and corresponding impact speeds of the test vehicles are showing very critical results. Regulation No. 1235/2011 of the European Parliament and the Council for Type Approval of Vehicles (EU) should be changed in such a way, that for C1-tyres (normal passenger cars tyres) the minimum wet grip index G is 1.25. All C2-tyres (light commercial vehicles tyres) should at least meet a minimum wet grip index of G = 1.1. All C3-tyres (heavy trucks and buses tyres) should at least meet a minimum wet grip index of G = 0.95. Due to the missing lower limits for G in the wet grip class F for C1, C2 and C3 tyres according to Commission Regulation (EU) No. 1235/2011, officially valid from 30 May 2012, a tyre-to-road coefficient of adhesion in the extreme of 0 (zero) is legally permitted. This is an apparent flaw in above cited EU Regulation, which causes a potential danger to the road traffic safety for all motor vehicles in Europe with such tyres. The wet grip class F has to be removed urgently from said EURegulation, since a direct liability of the responsible EU-Commission can not be excluded.
Bicyclists are minimally or unprotected road users. Their vulnerability results in a high injury risk despite their relatively low own speed. However, the actual injury situation of bicyclists has not been investigated very well so far. The purpose of this study was to analyze the actual injury situation of bicyclists in Germany to create a basis for effective preventive measures. Technical and medical data were prospectively collected shortly after the accident at the accident scenes and medical institutions providing care for the injured. Data of injured bicyclists from 1985 to 2003 were analyzed for the following parameters: collision opponent, collision type, collision speed (km/h), Abbreviated Injury Scale (AIS), Maximum AIS (MAIS), incidence of polytrauma (Injury Severity Score >16), incidence of death (death before end of first hospital stay). 4,264 injured bicyclists were included. 55% were male and 45% female. The age was grouped to preschool age in 0.9%, 6 to 12 years in 10.8%, 13 to 17 years in 10.4%, 18 to 64 years in 64.7%, and over 64 years in 13.2%. The MAIS was 1 in 78.8%, 2 in 17.0%, 3 in 3.0%, 4 in 0.6%, 5 in 0.4%, and 6 in 0.2%. The incidence of polytrauma was 0.9%, and the incidence of death was 0.5%. The incidence of injuries to different body regions was as follows: head, 47.8%; neck, 5.2%, thorax, 21%; upper extremities, 46.3%; abdomen, 5.8%; pelvis, 11.5%, lower extremities, 62.1%. The accident location was urban in 95.2%, and rural in 4.8%. The accidents happened during daylight in 82.4%, during night in 12.2%, and during dawn/dusk in 5.3%. The road situation was as follows: straight, 27.3%; bend, 3.0%; junction, 32.0%; crossing, 26.4%; gate, 5.9%; others, 5.4%. The collision opponents were cars in 65.8%, trucks in 7.2%, bicycles in 7.4%, standing objects in 8.8%, multiple objects in 4.3%, and others in 6.5%. The collision speed was grouped <31 in 77.9%, 31-50 in 4.9%, 51-70 in 3.7%, and >70 in 1.5%. The helmet use rate was 1.5%. 68% of the registered head injuries were located in the effective helmet protection area. In bicyclists, head and extremities are at high risk for injuries. The helmet use rate is unsatisfactorily low. Remarkably, two thirds of the head injuries could have been prevented by helmets. Accidents are concentrated to crossings, junctions and gates. A significant lower mean injury severity was observed in victims using separate bicycle lanes. These results do strongly support the extension or addition of bicycle lanes and their consequent use. However, the lanes are frequently interrupted at crossings and junctions. This emphasizes also the important endangering of bicyclists coming from crossings, junctions and gates, i.e. all situations in which contact of bicyclists to motorized vehicles is possible. Redesigning junctions and bicycle traffic lanes to minimize the possibility of this dangerous contact would be preventive measures. A more consequent helmet use and use and an extension of bicycle paths for a better separation of bicyclists and motorized vehicle would be simple but very effective preventive measures.
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
Small overlap frontal crashes are defined by a damage pattern with most of the vehicle deformation concentrated outboard of the main longitudinal structures. These crashes are prominent among frontal crashes resulting in serious and fatal injuries, even among vehicles that perform well in regulatory and consumer information crash tests. One of the critical aspects of understanding these crashes is knowing the crash speeds that cause the types of damage associated with serious injuries. Laboratory crash tests were conducted using 12 vehicles in three small overlap test conditions: pole, vehicle-to-vehicle collinear, and vehicle-to-vehicle oblique (15-degree striking angle). Field reconstruction techniques were used to estimate the delta V for each vehicle, and these results were compared with actual delta V values based on vehicle accelerometer data. Estimated delta Vs were 50% lower than actual values. Velocity change estimates for small overlap frontal crashes in databases such as NASS-CDS significantly underestimate actual values.
Impact severity is a fundamental measure for all in-depth crash investigation projects. One methodology used in the UK is based on the US Calspan software package CRASH3. The UK- in-depth crash investigation studies routinely use AiDamage3 a software package which is based on an updated version of the original CRASH3 algorithm, including enhancements to the vehicle stiffness coefficients. Real world accident-damaged vehicles are measured and their crush is correlated with a library of stiffness coefficients. These measurements are then used, along with other parameters, to calculate the crash energy and equivalent changes of velocity of the vehicles (delta-v), which is a measure of the impact severity. UK in-depth accident studies routinely validate the crash severity methodologies applied as the vehicle fleet changes. This is achieved by analysing crash test data and using the appropriate residual crush damage and other inputs to AiDamage3 and checking the program- outputs with the known crash severity parameters. This procedure checks, at least in part, the default stiffness values in the data libraries and the reconstruction methods used.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
The term test procedure refers to a method that describes how a system has to be tested to identify and assess specific behavior or properties by experiments. This also includes the specification of required tools, equipment, boundary conditions, and evaluation methods. Test procedures are an essential tool to check whether desired product properties are present, which of course also applies to the development of driver assistance systems. In addition to development and release testing that mainly is performed by the vehicle or system manufacturer, there are tests with the purpose of an independent product testing that are conducted by external test organizations. These tests are needed for vehicle type approval (for admission to a specific market), in the context of applying the standard for functional safety (in both cases mainly executed by technical services (being accredited as certification laboratory)) or for customer information purposes (by a test institute for consumer protection). The focus of this chapter is these "external" test methods. After a taxonomy of test procedures, the differences between legislation (type approval) and consumer testing are highlighted. Typical tests and the associated test setup, tools, and assessment criteria are discussed, and an outlook toward testing in the near and mid-future is given.
The "Seven Steps Method" is an analysis and classification system, which describes the human participation factors and their causes in the temporal sequence (from the perceptibility to concrete action errors) taking into consideration the logical sequence of individual basic functions. By means of the "seven steps" it is possible to describe the relevant human causes of accidents from persons involved in the accident in an economic way with a sufficient degree of exactitude, because the causes can be further differentiated in their value (e.g. diversion as external diversion with regard to impact due to surroundings) and their sub values (e.g. external diversion with regard to impact due to surroundings in the shape of a "capture" of the perception by a prominent object of the traffic environment). Theoretically it is possible that one or more causing moments can be assigned to a person involved in an accident in each of the "seven steps"; however it is also possible to sufficiently clarify the cause in only one level (examples for this are described). In the practice of accident investigation at the site of the accident, the sequence chart is also relevant. With its assistance the questioning of the people involved in an accident can be accomplished in a structured way by assigning a set of questions to each step.
To determine whether the model "Accompanied driving from age 17" (AD17) contributes to improvement of young drivers' road safety, two large random samples of novice drivers drawn from the Central Register of Driving Licences (ZFER) held at the Federal Motor Transport Authority (KBA) were compared in terms of the rates of accident involvement and traffic offences at the start of their solo driving career. The samples comprised former participants in the AD17 model and novice drivers of the same age who had obtained a driving licence in the conventional manner immediately after their 18th birthday. Both analysis groups were contacted by post and asked to complete an online questionnaire. In response, 19,000 drivers reported on their first year of solo driving and on the occurrence of any accidents or traffic offences during this period. The analyses were repeated with two "silent" analysis groups comprising a total of 75,000 drivers, for whom any records of traffic offences were retrieved from the Central Register of Traffic Offenders (VZR), with a distinction being made between offences in connection with an accident and other offences. The AD17 model was introduced in all 16 German federal states between April 2004 and January 2008. By the end of 2009, almost one million novice drivers had participated in the model, and almost three-quarters of the target group - so-called "early beginners" who wished to commence solo driving immediately after reaching the age of 18 years - opted for the AD17 model. The phase of introduction of the model was associated with a temporary increase of around five per cent in the demand for driving licences from persons under 19 years of age. During the first year of solo driving, the rate of accident involvement for AD17 participants was 19 per cent lower and the rate of traffic offences 18 per cent lower than for drivers of the same age who had obtained their driving licence in the conventional manner. After adjustment for confounds (e.g. gender and vehicle availability), a reduction in accidents by 17 per cent and in traffic offences by 15 per cent remained as an effect attributable to the model. A comparison on the basis of the distances driven indicated 22 per cent fewer accidents and 20 per cent fewer traffic offences. The results are statistically significant and apply to both male and female drivers. The findings were confirmed in the replication study based on VZR data, with one exception: For female AD17 drivers, and here only for VZR-recorded offences excluding accidents, no significant reduction was found. On the other hand, the rate for female drivers is already lower than that of their male counterparts by three-quarters. Approximately 1,700 injury accidents were prevented by implementation of the model in 2009.
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of plastic materials as a material for the interior equipment of buses and coaches due to their good mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years " also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, also the production of smoke, the smoke development and propagation as well as its toxicity are of interest. That counts for the passengers as well as for the test methods and its limit values. The severe fire in Germany near Hanover in 2008 with 20 fatalities showed how disastrous such fires can be. For those reasons several research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behaviour of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and onboard extinguishing equipment were elaborated. On the other hand research was carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. In this project small and real scale experiments on material specimens, interior parts and vehicles were performed. Trains and buses often have very similar operation conditions. Consequently, bus interior material was tested according to the regulations for rail vehicles, i.e. DIN EN 45545 as well as DIN 5510. None of the tested bus interior materials would have been allowed to use in a train. The fire safety regulations for bus materials are on a low level compared to other transport sectors, i.e. railway, ship and aircraft. Also numerical investigations with the Fire Dynamics Simulator (FDS) were performed. The very rapid fire development during the severe bus fire from 2008 could be predicted with the numerical model. The model was then used to investigate the influence of different materials, ventilation conditions and ignition sources. The bus materials contribute significantly to a very rapid fire development in bus fires. Especially, the flammable ceiling and the passenger seats were identified to be key issues of the fire propagation in a bus and can be explained by the rapid fire spread along the ceiling and the high fire load of passenger seats. As conclusion of the project effective and economically reasonable fire safety requirements for interiors of buses are recommended which would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses
Since 2008, the authors inspected fatal traffic accidents on the spot every year, with the cooperation of Toyota police station in Aichi pref. In the jurisdiction, numbers of fatal accidents were 18 in 2008, 12 in 2009, 14 accidents in 2010, and 16 in 2011. We here report the results of our analysis of information obtained by detailed inspection for those that occurred from 2008 to 2010. We focused on vehicle-to-pedestrian accidents, which accounted for about 45% of all accidents in 2008. Because many accidents occurred on residential roads not far from pedestrians" homes, it was revealed that the decrease of the collision speed by traffic calming such as humps and zone speed management, was highly effective. On the other hand, pedestrian detection technologies seemed to be also effective as a countermeasure on vehicle side. Every pedestrian position against a vehicle was clarified and TTC (Time to Collision) was calculated provisionally. Pedestrian accidents in intersections were also examined. Among the intersection pedestrian accidents within the jurisdiction, compared with the national average in Japan, the ratio of intersections without a signal and the ratio without a pedestrian crossing were high. According to the comparison of the Japanese traffic accident patterns between 2001 and 2008, pedestrian accidents during turning right and turning left did not decrease much. For elderly drivers, these accidents occurred very often. Finally, single vehicle accidents were analysed with the accident pattern analysis methods used above. There were high numbers of single vehicle accidents against object on single roads. Although fatal accidents against guardrails decreased, the numbers of fatal accidents against a utility pole and a sign pole were nearly constant. As for the impact with narrow width objects such as utility poles, the fatality rate was very high, and countermeasures of both road infrastructure and vehicles seem to be effective.