Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (404) (entfernen)
Schlagworte
- Conference (324)
- Konferenz (320)
- Germany (151)
- Accident (150)
- Unfall (150)
- Deutschland (149)
- Injury (101)
- Verletzung (100)
- Unfallrekonstruktion (81)
- Analyse (math) (64)
This paper uses the national accident statistics of Great Britain to evaluate the effectiveness of Electronic Stability Control Systems (ESC) to reduce crash involvement rates. The crash experience of 8,951 cars is analysed and compared to a closely matching set of non-ESC cars using case-control methods. This is one of the largest ESC samples analysed to date. Overall the cars with ESC are involved in 3% fewer crashes although the effectiveness is substantially higher under conditions of adverse road friction. ESC equipped cars are involved in 15% fewer fatal crashes although this reduction represents the combined effect of ESC and passive safety improvements.
Cycle helmets have continued to increase in popularity since their introduction half a century ago. Many studies indicate that overall, head injury can be significantly reduced by wearing them. This study was conducted using two distinct sets of real-world cycling collision data from Ireland, namely cases involving police collision reports and cases involving admission to a hospital emergency department. The analyses sought to simulate and analyse the protective performance of cycle helmets in such collision scenarios, by comparing the Head Injury Criterion score and peak head accelerations, both linear and angular. Cycle collisions were simulated using the specialised commercial software MADYMO. From the simulation results, these key metrics were compared between the same-scenario helmeted and unhelmeted cyclist models. Results showed that the inclusion of bicycle helmets reduced linear accelerations very significantly, but also increased angular accelerations significantly compared to unhelmeted situations. Given the modest protective performance of cycle helmets against angular accelerations, it is recommended that cycle helmet manufacturers and international test standards need to pay more attention to head angular accelerations.
76 severe traffic accidents had been investigated in depth in an ongoing Volkswagen-Tongji University joint accident research project in JiaDing district, Shanghai, PR China since June 2005. With a methodology similar to German accident research units in Dresden and Hannover, a research team proceeds to the scene immediately after the incident to investigate and collect various data on environment, accident occurrence, vehicle state and deformations as well as injuries. The data combined with the results of accident reconstruction will be stored in a database for further statistical and casuistic analysis. The first outcome of the project supports the hypothesis that a main causation for the large number of traffic accidents in China is the lacking of risk awareness in Chinese driver behaviour. Low seat-belt use and the high proportion of vulnerable and poorly protected two-wheelers in traffic are reasons for the high injury and fatality rate in China. The research work shows that accident research in China is feasible and able to give support to tackle one of the urging problems in Chinese development.
The effect of fatigue on driving has been compared to the effect of alcohol impairment in both driver performance and crash studies. However are crash characteristics and causation mechanisms similar in crashes involving fatigue to those involving alcohol when studied in the real world? This has been explored by examining data held in the EC project SafetyNet Accident Causation Database. Causation data was recorded using the SafetyNet Accident Causation System (SNACS). The focus was on Cars/MPV crashes and drivers assigned the SNACS code Alcohol or Fatigue. The Alcohol group included 44 drivers and the Fatigue group included 47. "Incorrect direction" was a frequently occurring critical event in both the Alcohol and Fatigue groups. The Alcohol group had more contributory factors related to decision making and the Fatigue group had more contributory factors relating to incorrect observations. This analysis does not allow for generalised statements about the significance of the similarities and differences between crashes involving alcohol and fatigue, however the observed differences do suggest that attempts to quantify the effect of fatigue by using levels of alcohol impairment as a benchmark should be done with care.
Event Data Recorder (EDR) is an additional function installed in airbag control module (ACM) to record vehicle and occupant information for a brief period of time before, during, and after a crash event. EDRs are now being installed in ACMs by several automakers in the USA and in Japan. The aim of this study is to understand the performance of EDRs for the improvement of accident reconstruction with more reliable information. In the first report of the study, data obtained from EDRs of seven vehicle types were evaluated using 2006-2007 J-NCAP (Japanese new car assessment program) full-lap frontal barrier crash tests and offset frontal deformable barrier crash tests data. For more practical standpoint, we conducted thirteen crash tests reconstructing typical real-world accidents such as single vehicle accidents with barriers or poles, car to car accidents and multi rear-end collisions focusing on Japanese typical accident types. Data obtained from EDRs are compared with data obtained from optical speed sensor, instrumented accelerometers and high speed video cameras. The velocities determined from pre-crash data of EDRs and the maximum change in velocity, delta-V, and delta-V time history data obtained from post-crash data of EDRs are analyzed. The results are as follows: - Pre-crash velocities of EDRs were very accurate and reliable. An average difference between the EDR recording values and reference speeds was 4.2% and a root mean square of the differences was 9.2%. Only two cases resulted large differences for the pre-crash velocity. Both of them were cases with braking prior to the collision. However, another test with braking resulted less difference. The braking condition may influence accuracy of pre-crash velocities. - Maximum delta-Vs obtained from the EDRs showed uncertainty of measurement in several cases in comparisons with the reliable delta-V data. The differences in maximum delta-V were more than 10% in five of twenty-five events data and more than 20% in two of twenty-five events data. An average of the all differences was about 4% and root mean square of the differences was about 11%. Especially large deformation at narrow area may influence accuracy of post-crash delta-V. - Multiple rear-end crash tests were reconstructed using EDRs data as case studies. Some EDRs recorded two events and a time gap between two events, so that these reconstruction case studies were very accurate and reliable. - If though only one of three vehicles in multiple rear end crash was equipped EDR, overview and velocities of all cars may be reconstructed using these limited EDR data. In this case study, leading car- EDR data and middle car- EDR data were valuable. However if only following car was equipped EDR, the reconstruction was not accurate
The aim of this study was to evaluate the performance and accuracy of Event Data Recorders (EDRs). The analysis was based on J-NCAP crash tests from 2006"2007, with the corresponding EDR datasets. The pre-crash velocity, maximum delta-V and delta-V versus time history data recorded in the EDRs were compared with the reliable crash test data. The difference between the EDR pre-crash velocity and the laboratory test speed was less than 4 percent. In contrast, in several cases the maximum delta-V and delta-V versus time history data obtained from the EDRs showed uncertainty of measurement in comparisons with the reliable delta-V data. The difference in maximum delta-V in these comparisons was more than 5 percent in 10 of 14 tests and more than 10 percent in 4 of 14 tests. The EDRs underestimated the maximum delta-V in almost all tests. It was also concluded that the calculated acceleration from the EDR delta-V versus time history data showed good agreement with the instrumented accelerometer signal during the collision in almost all tests.
Die Ergebnisse der vorliegenden Studie zeigen, dass Patienten mit einer unbehandelten Aufmerksamkeitsdefizit/Hyperaktivitätsstörung in verstärktem Maße verkehrsrechtlich auffällig werden und sowohl häufiger Unfälle verursachen als auch Ordnungswidrigkeiten begehen. Die Ergebnisse zeigen weiterhin, dass sich eine medikamentöse Behandlung günstig auf die verkehrsrelevanten Leistungsfunktionen auswirkt und dadurch auch die Grundvoraussetzungen für eine verbesserte Fahrtüchtigkeit und Fahreignung ermöglicht.
Die Ergebnisse der vorliegenden Studie zeigen, dass die Art, wie ein Fahrer mit Belastungen im Straßenverkehr umgeht, in Zusammenhang steht mit seinem Fahrstil und den Fahrfehlern, die er macht. Dabei zeigt sich, dass insbesondere ein konfrontativer Bewältigungsstil die Konfliktneigung im Straßenverkehr erhöht und dass diese Fahrer nicht nur andere belasten, sondern dass dieser Bewältigungsstil auch dazu führt, dass diese Fahrer selbst mehr Stress und Belastungen erleben.
Kategorie-1-Schäden bei orthotropen Fahrbahnplatten treten als bauweisenunabhängige Schäden in Form von Rissen im Anschlussbereich Deckblech-Längsrippe auf. Zur Vermeidung dieser Schäden sind geeignete Instandsetzungsmaßnahmen zu entwickeln, die zu einer Verminderung der Spannungen und Durchbiegungen in den gefährdeten Bereichen führen. Im Rahmen eines aktuellen Forschungsvorhabens an der Universität Duisburg-Essen wird der Ansatz verfolgt, einen modifizierten Fahrbahnbelag bestehend aus einem mit Epoxydharz oder alternativ mit Bioharz verfüllten Asphalttraggerüsts mit erhöhter mittragender Wirkung einzusetzen. Des Weiteren wird im vorliegenden Beitrag der Einsatz von Betonfertigteilen aus UHPC erläutert.
Im Falle von Nachtrunkeinlassungen ist die Begleitstoffanalyse (BGA) ein anerkanntes Instrument zu deren Überpruefung. Methanol ist einer der forensisch relevanten Begleitalkohole, die bei der Begleitstoffanalyse überprüft werden. Oft kann die BGA den Nachtrunk weder bestätigen noch ausschließen, ein erhöhter Methanolspiegel hat deshalb als Marker für eine stundenlang vorbestehende Ethylalkoholbeeinflussung von mehr als 0,5 bis 0,7 Promille eine besondere Bedeutung. Oft gehörte Einlassungen zur Erklärung erhöhter Methanolspiegel sind nach Erfahrung von Rechtsmedizinern der Genuss von Obst, so zum Beispiel Orangen, Pampelmusen, Birnen und auch Tomaten, Saftkonsum oder eine Methanolexposition am Arbeitsplatz. Es werden zwei Fallbeispiele vorgestellt, in denen diese Einlassungen experimentell überprüft wurden. Im ersten Fall wurde der Methanolspiegel mit dem Genuss verdorbenen Fruchtsafts begründet, im zweiten Fall wurde ein Nachtrunk mit Klosterfrau-Melissengeist beziehungsweise eine Diät mit Obst angegeben. Ob Methanolspiegel nach dem Konsum von Obst tatsächlich hoch ansteigen können, wurde in Probandentests untersucht. Bei einigen Probanden wurden hohe Methanolspiegel von etwa 10mg/l nach exzessivem Obst- und Fruchtkonsum vorgefunden. Bei der Bewertung dieser Spiegel als Marker für eine chronische Alkoholbelastung ist deshalb Vorsicht geboten. Verdorbener Obstsaft enthält lediglich geringe Konzentrationen von Alkohol und Methanol.
Road safety is a major preoccupation of the European Commission and the road transport industry and depends on numerous significant factors. In order to improve road safety and to plan effective safety improvement actions for truck transport, we must first identify the problems to be addressed, i.e. what are the main causes of truck accidents. The ETAC project, initiated by the European Commission and the IRU, was launched in order to set up a heavy goods vehicle accident causation study across European countries to identify future actions which could contribute to the improvement of road safety. The results will be based on a detailed analysis of truck accident data collected in seven European countries according to a common methodology which has been elaborated through numerous national and European projects. This paper describes the common methodology used to collect the information on the scene of the accident and to analyse the data so that the reconstruction of the crash events may be carried out. CEESAR proposes a methodology using its experience gained from over 10 years of accident data collection. This methodology is based on an in-depth investigation of the parameters involved in-an accident and linked to the driver, the vehicle, the road and their environment. In-depth investigation requires accident investigator presence on the scene of the accident in order to collect volatile information such as marks on the road, weather conditions, visibility, state and equipment of the vehicle, driver interview. Later, passive and active information is gathered, either at the hospital for the driver, at the garage for the vehicle or on the spot for the road geometry. A reconstruction carried out with the help of specific software and the analysis of the data collected and calculated enables the identification of the main causes of the accident and the future actions to plan in order to improve road safety as regards truck traffic.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
Sedan type vehicles in which adult rear seat passengers were present and which were involved in frontal collisions were investigated, and the influence of unbelted rear seat passengers on the injuries of front seat occupants was studied. Unbelted rear seat passengers move forward during impact. It was observed that there were not only cases in which front seat occupants sustained injuries caused by direct contact with rear seat passengers, but also cases where front seat occupants received severe injuries due to additional force from rear seat passengers, either impacting directly or indirectly as a result of deformation of the front seat. Severe injuries of front seat occupants were observed in the latter cases. This research validates the importance of seat-belt use for rear seat passengers, not only to protect themselves but also to mitigate injuries of front seat occupants.
Motorcycle safety research
(2007)
Honda- global motorcycle sales exceeded the 10 million units mark since 2004, and further expansion is expected. As a responsibility for a company to provide mobility, Honda is focusing on motorcycle safety as top priority and has been working on various activities for both aspects of hardware and software. Here, we present Honda- activity for the safety technology of motorcycles. At present, Honda is promoting motorcycle safety in the four themes of prevention and collision safety such as safety education, recognition assistance, accident prevention and injury reduction. First, in the area of the safety education, the "Honda Safety Driving Promotion Center" was established in 1970, and motorcycle riders and vehicle driver trainings have been organized, and the traffic training centers are used as an actual practice field not only in Japan but also in many other regions in the world. Through our training activities, the new area of safety training with hardware assistance was developed and Honda- unique technology was accumulated such as the riding simulator which can provide experience of potentially dangerous situations without risk. Especially, the "riding trainer", the popular version of the riding simulator, was introduced at several motor shows in various countries and launched in September 2005. It was distributed first in Europe and is expected to expand globally aiming at 3000 units worldwide.. And in Europe, the newest version, which includes the suburban roads program, jointly developed with ADAC, will be released in near future. In the area of recognition assistance, "vehicle to vehicle communication technology" is under development using the advantage of being a manufacturer of both motorcycles and cars. This technology is under research as Honda "ASV-3" in Japan, and as part of C2C activity in Europe. As for the accident prevention, advanced brake systems for motorcycles to assist more effective brake operation have been expanded, Honda signed the European Road Safety Charter in April 2004 with the advanced brake systems commitment and furthermore, they are expanding according to vehicle characteristics and region. Then all models above 250 cc will have a version of the system by 2010. And as the last theme, "motorcycle airbag system" is introduced which is equipped on a mass production motorcycle for the first time in the world. It has been researched and developed for a long time as an injury reduction technology for collision accidents. Honda automobile technology was used for the research and development of the motorcycle airbag, and many specific issues such as the analysis of the collision conditions particular to motorcycles have been solved to realize today- success. It might be known that ADAC in-house crash test held in August this year confirmed the high effectiveness of the airbag system and showed a positive result. This motorcycle airbag system is equipped to the Honda Gold Wing and launched in North America in August, 2006. Also in Europe, it will be sold by the end of this year. Each theme of Honda motorcycle safety technology can be seen at the Honda booth.
Small overlap frontal crashes are defined by a damage pattern with most of the vehicle deformation concentrated outboard of the main longitudinal structures. These crashes are prominent among frontal crashes resulting in serious and fatal injuries, even among vehicles that perform well in regulatory and consumer information crash tests. One of the critical aspects of understanding these crashes is knowing the crash speeds that cause the types of damage associated with serious injuries. Laboratory crash tests were conducted using 12 vehicles in three small overlap test conditions: pole, vehicle-to-vehicle collinear, and vehicle-to-vehicle oblique (15-degree striking angle). Field reconstruction techniques were used to estimate the delta V for each vehicle, and these results were compared with actual delta V values based on vehicle accelerometer data. Estimated delta Vs were 50% lower than actual values. Velocity change estimates for small overlap frontal crashes in databases such as NASS-CDS significantly underestimate actual values.
This work aimed for getting the main features of accidents involving Light Goods Vehicles (LGV), using accident cases collected in the In-Depth Accidents Studies built up at IFSTTAR-LMA (France), in order to analyse thoroughly the proceedings of these accidents and identify the major factors for the different types of LGV. This work was based on the analysis of 88 accident cases involving LGV with a Maximum Authorised Mass inferior to 3.5 tonnes. In particular kinematics reconstruction of these accidents were performed to calculate the average impact speeds and to better understand the compatibility problems between LGV and antagonist vehicles. Specific features have been reviewed to pick up problems concerning safety, maintenance, loading, LGV design: general conditions of the accident, vehicle features, and passive safety. The main results of this study are presented in this paper.
Detailed investigations and reconstructions of real accidents involving vulnerable road users
(2005)
The aim of this research is to improve knowledge about vulnerable road users accidents and more specifically pedestrians or cyclists. This work has been based on a complete analysis of real accidents. From accidents chosen from an in-depth multidisciplinary investigation (psychology, technical, medical), we have tried to identify the configuration of the impact: car speed, pedestrian or cyclist orientations. Then, we have made a numerical modelling of the same configuration with a multibody software. In particular, we have reproduced the anthropometry of the victim and the front shape of the car. A first simulation has been performed on this starting configuration. Next, effects of some parameters such as car velocity or victim position at impact have been numerically studied in order to find the best correlations with all indications produced by the in-depth analysis. Finally, the retained configuration was close to the presumed real accident conditions because it reproduces in particular the same impact points on the car, the same injuries, and is according to the driver statement. This double approach associating an in-depth accident analysis and a numerical simulation has been applied on pedestrian-to-car and bicyclist-tocar accidents. It has allowed us to better understand the real kinematics of such impacts. Even if this method is based on a case to case study, it underlines which parameters are relevant on a vulnerable road user accident investigation and reconstruction.
PROSPECT (Proactive Safety for Pedestrians and Cyclists) is a collaborative research project involving most of the relevant partners from the automotive industry (including important active safety vehicle manufacturers and tier-1 suppliers) as well as academia and independent test labs, funded by the European Commission in the Horizon 2020 research program. PROSPECT's primary goal is the development of novel active safety functions, to be finally demonstrated to the public in three prototype vehicles. A sound benefit assessment of the prototype vehicle's functionality requires a broad testing methodology which goes beyond what has currently been used. Since PROSPECT functions are developed to prevent accidents in intersections, a key aspect of the test methodology is the reproduction of natural driving styles on the test track with driving robots. For this task, data from a real driving study with subjects in a suburb of Munich, Germany was used. Further data from Barcelona will be available soon. The data suggests that intersection crossing can be broken down into five phases, two phases with straight deceleration / acceleration, one phase with constant radius and speed turning, and two phases where the bend is imitated or ended. In these latter phases, drivers mostly combine lateral and longitudinal accelerations and drive what is called a clothoid, a curve with curvature proportional to distance travelled, in order to change lateral acceleration smoothly rather than abrupt. The data suggests that the main parameter of the clothoid, the ratio distance travelled to curvature, is mostly constant during the intersections. This parameter together with decelerations and speeds allows the generation of synthetic robot program files for a reproduction of natural driving styles using robots, allowing a much greater reproducibility than what is possible with human test drivers. First tests show that in principle it is possible to use the driving robots for vehicle control in that manner; a challenge currently is the control performance of the robot system in terms of speed control, but it is anticipated that this problem will be solved soon. Further elements of the PROSPECT test methodology are a standard intersection marking to be implemented on the test track which allows the efficient testing of all PROSPECT test cases, standard mobile and light obstruction elements for quick reproduction of obstructions of view, and a concept for tests in realistic surroundings. First tests using the PROSPECT test methodology will be conducted over the summer 2017, and final tests of the prototype vehicles developed within PROSPECT will be conducted in early 2018
Das Ziel des DRUGS-Kurses ist eine dauerhafte Distanzierung vom Drogenkonsum durch Drogenabstinenz. Der Kursteilnehmer verpflichtet sich, für die Dauer des Kurses jeglichen Drogenkonsum zu unterlassen. Während des Kurses erfolgt eine Abstinenzkontrolle durch ein forensisch verwertbares Drogenscreening. Auf die Basisstufe entfallen die ersten vier Sitzungen. Darauf folgt eine vierwöchige Selbstbeobachtungsphase, in der auch das Drogenscreening durchgeführt wird. Die in der Selbstbeobachtungsphase gemachten Erfahrungen werden in der anschließenden Aufbauphase besprochen und optimiert. Der individualpsychologische Ansatz berücksichtigt insbesondere die Psychodynamik in der Gruppe. Die Teilnehmer, welche Drogenkonsum oft mit Gruppennormen und -zwängen verbinden, können hier auch die Erfahrung machen, dass sie als Einzelne in der Lage sind, Gruppennormen mitzugestalten und sich davon, wo nötig, zu distanzieren und eine eigene Position in der Gruppe einzunehmen. Die Gruppe bietet auch das Übungsfeld für Verhaltensweisen, welche in der sozialen Gruppe außerhalb des Kurses notwendig sind.
Real world accident reconstruction with the Total Human Model for Safety (THUMS) in Pam-Crash
(2013)
Further improvement of vehicle safety needs detailed analysis of real world accidents. According to GIDAS (German In-Depth Accident Study) most car to car front accidents occur at mid-crash severity. In this range thoracic injuries already occur. In this study a real world frontal crash with mid-crash severity out of the AARU database was reconstructed. The selected car to car accident was reconstructed by AARU by means of pc-crash software in order to get the initial dynamic accident conditions. These initial conditions were used to reconstruct the complete accident in more detail using FE models for the car structure and the occupants. Occupant simulations were performed with FE HIII-dummy models and the THUMS using Pam-Crash code. An initial THUMS validation was performed in order to verify the model-´s biofidelity by means of table-top test simulations. THUMS bone stiffness values were modified to match the real word occupant age. A comparison between driver and passenger restraint system loading was done, as well as an injury prediction comparison between the HIII-dummy model and THUMS response for both cases. Detailed comparison between the HIII-dummy models and THUMS regarding thoracic loading are discussed.
Die Brücke hat eine Länge von 660 Metern und überquert das Haseltal mit einer maximalen Höhe von 70 Metern. Sie ist ein Durchlaufträger über sieben Felder mit Stützweiten von 5 x 101,60 Metern für die Mittelöffnungen und 2 x 76,20 Metern für die Endfelder. Zwei im Abstand von 18,53 Metern angeordnete vollwandige Hauptträger unterstützen die als orthotrope Platte ausgebildete 29,30 Meter breite Fahrbahntafel. Die seitlichen Kragarme sind über 5 Meter weit gespannt. Erbaut wurde die Brücke in den Jahren 1959 bis 1961. Die konstruktive Ausbildung des Überbaus wird im Einzelnen beschrieben. Auffällig ist das geringe Flächengewicht des Überbaus von nur 248 Kilogramm je Quadratmeter. Beschrieben wird zunächst der Bauablauf mit einigen Besonderheiten, ausserdem die Prüfungen während der Bauausführung und der Zustand des Bauwerks zum Ablauf der zehnjährigen Gewährleistungszeit. Bei einer Hauptprüfung des Überbaus wurden 1983 neben anderen Schäden zahlreiche systematische Risse, besonders in den Schweissnähten festgestellt, die 1985 bis 1988 zu einer umfangreichen Instandsetzung führten. Im Jahre 2002 wurden erneut viele Risse in den Schweissnähten gefunden, die umgehend wieder instand gesetzt wurden. Es wurden jährliche Sonderprüfungen angeordnet und wegen des desolaten Zustandes des Überbaus ein Neubau beschlossen. Einzelheiten zu den Schadensursachen, die durch Gutachten und Versuche festgestellt wurden, werden dargestellt.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
Aufgrund ständig steigender Verkehrsintensität und gleichzeitig ansteigenden Fahrzeuggewichten werden auch die Stahlbrücken mit orthotropen Fahrbahnplatten hinsichtlich Ermüdung stärker beansprucht. Zumeist wurden diese Brücken in den 60er Jahren gebaut und die heutigen Qualitätsstandards und Empfehlungen wurden nur zum Teil eingehalten. Ein nicht ausreichender Ermüdungswiderstand der Details in Kombination mit steigenden Ermüdungsbeanspruchungen führt früher oder später zu Schäden; bei einigen Brücken in Deutschland sind Schäden aufgetreten. Die zukünftige Verkehrsbeanspruchung führt dazu, dass eine Reparatur alleine nicht ausreichend ist, sondern eine nachhaltige Instandsetzung, das heisst Ertüchtigung bestehender orthotroper Platten erfolgen muss, um auch bei weiter ansteigenden Ermüdungsbeanspruchungen eine hinreichende Gesamtlebensdauer ohne erhöhten Wartungsaufwand sicherzustellen. Vor diesem Hintergrund haben das Bundesministerium fuer Verkehr, Bau- und Wohnungswesen (BMVBW) und die Bundesanstalt fuer Straßenwesen (BASt) ein Forschungsvorhaben in Auftrag gegeben, um nachhaltige Instandsetzungsmaßnahmen zur Ertüchtigung von orthotropen Fahrbahnplatten bei Stahlbrücken unter der besonderen Berücksichtigung des Belagsystems zu untersuchen und zu entwickeln. Zurzeit sind verschiedene Lösungen zur nachhaltigen Ertüchtigung orthotroper Fahrbahnplatten in der Erforschung, teilweise wurden bereits erste Probeanwendungen durchgeführt. Erste Pilotprojekte wurden in Deutschland mit der SPS-Maßnahme, dem Einsatz von PmB 25 und in den Niederlanden unter anderem mit dem hochfesten, mit Stahlfasern versehenen und bewehrten Beton durchgeführt. Zu weiteren Möglichkeiten, wie dem offenporig mit Epoxidharz vergossenen Asphalt, werden noch Bauteilversuche durchgeführt, die die Wirksamkeit solcher Maßnahmen bestätigen sollen. Die Schlussfolgerungen sind zur Zeit wie folgt: - Behandlung bauweisenbedingter Schäden: Zur Behebung der Ursachen sind fallspezifische Lösungen erforderlich, die in der Regel nicht zu einer Verbesserung der allgemeinen Ermüdungsfestigkeit orthotroper Fahrbahnplatten beitragen. - Behandlung bauweisenunabhängiger Schäden: Die Instandsetzung der Schäden ist möglichst in Kombination mit einer geeigneten Ertüchtigungsmaßnahme durchzuführen, sodass die orthotrope Fahrbahnplatte auch für zukünftige Verkehrsbeanspruchungen dauerhaft ist. - Die Instandsetzungsmaßnahmen sind im Gesamtzusammenhang des Brückenbauwerks zu sehen: Die Instandsetzung von Schäden ist in einem Gesamtzusammenhang mit anderen erforderlichen Unterhaltungsmaßnahmen an der Brücke zu sehen, so kann zum Beispiel eine mögliche Schweissreparatur an der Brücke ein Auswahlkriterium für die Art der Belagserneuerung und die Wahl einer geeigneten Abdichtung sein.
Stahlbrücken mit orthotropen Fahrbahnplatten haben in Deutschland eine lange Traditon, bedürfen aber aufgrund der ständig gestiegenen Belastung durch den Schwerverkehr in einigen Fällen einer Instandsetzung oder sogar einer nachträglichen Verstärkung. Der Beitrag stellt vor diesem Hintergrund neue Wege und Methoden zur Verstärkung orthotroper Fahrbahnplatten vor und erläutert die Grundsätze und Randbedingungen ihrer Anwendung. Alle Erfahrungen haben gezeigt, dass nur Verstärkungsmethoden, die das Trag- und Verformungsverhalten der orthotropen Platte beachten und verbessern, erfolgreich sind. Nachdem die technische Entwicklung der orthotropen Platte dargestellt wurde, geht der Bericht auf die Bemessung sowie auf das Trag- und Verformungsverhalten dieses Bauteils ein. Grundsätzlich erfolgt die Berechnung und Bemessung der orthotropen Platte durch Zerlegung des Gesamtsystems in einzelne Subsysteme, die den Kräfteweg von den einwirkenden Reifenlasten bis in die Auflagerkräfte der Brücke stufenweise nachvollziehen. Auf die Bemessung der Subsysteme und die potenziell an den Systemen möglichen Schäden wird eingegangen. In einem weiteren Teil behandelt der Bericht Erfahrungen mit Instandsetzungsverfahren. Die Gefährdung der Dauerhaftigkeit der Bauteile wird in die Kategorien 1 bis 4 eingeteilt, mit Kategorie 1 als höchster Gefährdungsstufe. Die bei den einzelnen Kategorien aufgetretenen Schäden, ihre Ausprägung und die Ursachen des Entstehens werden erläutert. Der Bericht beschreibt auch Planungsmittel für Instandsetzungs- und Verstärkungsmaßnahmen sowie prophylaktische Verstärkungsmaßnahmen und die Entwicklung nachhaltiger Verstärkungen. Dabei spielt bei einigen Maßnahmen die Verbesserung der Verbundeigenschaften zwischen Stahlblech und Asphaltbelag eine wichtige Rolle. Weitere Entlastungsmöglichkeiten des Deckblechs bestehen darin, die Steifigkeit durch eine aufgesetzte Sandwichkonstruktion zu vergrößern oder das Deckblech mit einer 50 mm dicken Schicht aus bewehrtem hochfesten Stahlfaserbeton zu verstärken.
Die Begutachtung der Fahreignung beinhaltet in Deutschland neben einer medizinischen Untersuchung und einer psychologischen Exploration gegebenenfalls auch die Anwendung anlassbezogener verhaltenswissenschaftlicher/psychologischer Testverfahren. Diese stellen keine isolierte Maßnahme dar, sondern sind Bestandteil eines Begutachtungsprozesses. Dabei stellt der sachgerechte Gebrauch von so genannten Grenzwerten unter Berücksichtigung der Einzelfallgerechtigkeit und der Einhaltung des Grundsatzes der Verhältnismäßigkeit eine unabdingbare Voraussetzung dar. Testwerte sind nicht absolut, sondern relativ und üben von daher einen eher geringen Einfluss auf das Gutachtenergebnis in Bezug auf eine Prognose des Verkehrsverhaltens aus. Im Bereich des Verkehrsverhaltens kommt es nicht entscheidend darauf an, ob eine im Milli- oder Nanobereich exakte Messgenauigkeit erreicht wird, sondern wie die verkehrsmedizinischen, verkehrspsychologischen, technischen und anderen Sachverständigen mit dem Messwert fachlich umgehen. So müssen im Bereich der Begutachtung der Fahreignung tätige psychologische und medizinische Sachverständige in der Lage sein, Befunde im Einzelfall fehler-, mangel- sowie widerspruchsfrei zu interpretieren. Dies beinhaltet auch, sich mit den Ergebnissen eines psychologischen Testverfahrens fach- und sachgerecht auseinanderzusetzen, nach Kompensationsmöglichkeiten zu suchen und gegebenenfalls eine psychologische Fahrverhaltensbeobachtung durchzuführen. Bei grenzwertigen Vorgaben handelt es sich nicht um "Cut-Offs", sondern um "kritische Grenzwerte", die im Zusammenhang mit mehreren anderen Faktoren zu werten sind.
The accident research of Hanover and (from 1999 on) Dresden registered 736 leg injuries (AIS ≥ 2) from 1983 to March 2007. 174 of these injuries (23.6 %) were fractures or dislocations of foot and ankle. 149 feet of 141 front seat car occupants in 140 cars were affected. Of these 117 were drivers, 24 were front seat passengers. The mean age of occupants was 38.5 -± 16.8 years. Ankle fractures were the most frequent injury (n = 82; 80 malleolar fractures, 2 pilon fractures). 34 fractures and dislocations affected the hindfoot (5 talus and 26 calcaneal fractures, 2 subtalar dislocations and 1 subtotal amputation) , 16 to midfoot (4 navicular fractures, 5 cuboid fractures, 3 fractures of cuneiformia, 2 dislocations of chopart joint, 1 subtotal amputation, and one severe decollement) and 39 the forefoot (metatarsal fractures). Open fractures were seldom seen (2 malleolar fractures, 1 metatarsal fracture). Both feet were injured in 10 cases. 33 occupants (23.4 %) were polytaumatic had a polytrauma, 17 of them died. 81 percent of the occupants were belted. The cars were divided in pre EuroNCAP (year of manufacture 1997 and older) and post EuroNCAP cars (year of manufacture 1998 and newer). Most of the foot injuries were seen in pre EuroNCAP cars. Most of the occupants sat in compact cars (40 drivers and 9 front seat passengers) and large family cars (27 drivers and 7 co-drivers). 49 of 140 accidents occurred on country roads, 26 on main roads and 13 on motorways. The crash direction was mostly frontal. Generally were found no differences of delta v- and EES-level between the injured foot regions, but divided into pre- and post-EuroNCAP cars there was a tendency to higher delta v- and EES-levels in newer cars. The frequency of foot injuries increased linearly with increasing delta v-level; but above delta v-level of 55 km/h the linear increase only was seen in pre-EuroNCAP cars, post-EuroNCAP cars showed no further increase of injuries. The footwell intrusion showed no difference between the injured foot regions but pre-EuroNCAP cars had a tendency to higher footwell intrusion. There were no differences in footwell intrusion between the car types. Only 29 of 174 fractures or dislocations of foot were seen in post-EuroNCAP cars, the predominate number of these injuries (n = 145) were noticed in pre-EuroNCAP cars. A lower probability of long-term impairment was found in post-EuroNCAP cars for equal delta v levels, using the AIS2008 associated Functional Capacity Index (FCI) for the foot region.
The improvement of passive car security devices led to a reduction of injuries, especially of the head, the neck and the torso mainly due to the airbag function. The passenger's foot and ankle could not profit from this development. Some investigators even reported a progression of leg injuries (1). In this study, we investigated a current collective of patients with foot and ankle fractures or severe soft tissue injuries in relation with defined crash parameters. Special interest was paid to the car's footwell.
Since its creation in 2011 the Pre-Crash-Matrix (PCM) offers the possibility to observe the pre-crash phase until five seconds before crash for a wide range of accidents. Currently the PCM contains more than 8.000 reconstructed accidents out of the GIDAS (German In-Depth Accident Study) database and is enlarged continuously by more than 1.000 cases per year. Hence, a detailed investigation of active safety systems in real accident situations has been made feasible. The PCM contains all relevant data in database format to simulate the pre-crash phase until the first collision of the accident for a maximum of two participants. This includes the definition of the participants and their characteristics, the dynamic behavior of the participants as time-dependent course for five seconds before crash as well as the geometry of the traffic infrastructure. The digital sketch of the accident and information from GIDAS as well as from supplementary databases represent the main input for the simulation of the pre-crash phase of an accident with the VUFO simulation model VAST (Vufo Accident Simulation Tool). This simulation in turn embodies the foundation of the PCM. The PCM underlies continual improvements and enhancements in consultation with its users. In addition to collisions of cars with other cars, pedestrians, bicycles and motorcycles the PCM now also covers car to object and car to truck collisions. The paper illustrates car to truck collisions as a showcase and explains perspectives for further developments. In 2016 a more detailed definition of the contour of the vehicle was added. Furthermore, the geometrical surroundings of the accident site will be provided in a new structure with a higher level of detail. Thus, a precise classification of road marks and objects is possible to further improve the support of developing and evaluating ADAS. This paper gives an overview about the latest developments of the PCM with its innovations and provides an outlook to upcoming enhancements. Besides potential areas of application for the development of ADAS are shown.
The sequence of accident events can be classified by three essential phases, the pre-crash-sequence, the crash-sequence and the post-crash-sequence. The level of reliability of the information in the GIDAS-database (German In Depth Accident Study) is provided predominantly on the passive side. The period to evaluate active safety systems begins already in the pre-crash-sequence. The assessment of the potential of sensor- or communication-based active safety systems can only be accomplished by a detailed analysis of the pre-crash-phase. Hence the necessity to analyze the early period of the accident event in detail arises. This is possible with the help of the digital sketches of the accident site and the simulation of the accident by a simulation method of the VUFO GmbH. After simulating the pre-crash scenario it is possible to generate additional and standardized data to describe the pre-crash-sequences of an accident in a very high detail. These data are documented in a second database called the GIDAS Pre-Crash-Matrix (PCM). The PCM contains various tables with all relevant data to reproduce the pre-crash-sequence of traffic accidents from the GIDAS database until 5 seconds before the first collision. This includes parameters to describe the environment data, participant data and motion or dynamic data. This paper explains the creation of the PCM, the simulation itself and the contents and structure of the PCM. With this information of the pre-crash-sequence for various accident scenarios an improved benefit estimation and development of active safety systems can be made possible.
Nowadays airbags are part of the standard equipment in almost all new cars. While airbags are saving an increasing number of people from severe injuries and death in moderate and high speed crashes, they do not completely prevent dashboard injuries. The most common mechanism in dashboard injuries is a posteriorly directed force to the proximal tibia with the knee flexed. This may occur during a motor vehicle frontal impact accident when a knee of the driver or the front-seat passenger strikes the dashboard. The posterior force can be combined with a abducting or rotational force leading to concomitant lateral or posterolateral injury. Car and airbag manufacturers therefore develop special inflatable systems to reduce the impact force in dashboard injuries. Every new inflatable system, however, has to be evaluated in out of position situations in which the system might cause injuries to certain body areas. Therefore, we investigated a new kneebag system in different critical seating positions of post mortem test subjects (PMTS). The tested knee airbag module is a folded airbag (18 litre volume) which is installed below the lower section of the instrument panel of a passenger car. Using four PMTS (2 male, 2 female, age 36"67) the following positions were tested: normal seating position, knee flexed >90 degrees and knee flexed <60 degrees in static deployment tests with direct contact. In addition a dynamic test (48.8kph, AAMA-pulse) was carried out with the PMTS belted in a normal seating position. The inflation phase and the impact of the system on the knee/lower leg were analysed by high speed videos. After the test the lower legs of the PMTS were examined by Xray and autopsy. All soft tissue injuries and bone fractures were recorded. All the tests could be evaluated. Except some superficial skin lesions in the impact area no fracture of the bones around the knee and no knee ligament and tendon injuries were observed. Neither video analysis nor autopsy of the PMTS showed any critical contact injuries caused by the inflation process of the bag. Therefore, it can be concluded that in the tested seating positions which are the most critical for the knee area the knee bag system is safe.
The primary goal of this investigation was to determine the relative risk of traffic accidents in students. In a two year period, a survey amongst 2,325 students was carried out, and 3,645 injuries sustained by students treated at our hospital were analyzed. Moped-riding in adolescents were associated with a 23.75-fold increased risk for injury as compared to biking. Children who ride bicycles have a 2.2-fold increased risk for an injury sustained by traffic accidents compared to pedestrians. None of 50 injured bicycle riders with helmet had an AIS for head injuries of more than 2. 24 of 233 injured bicycle drivers without helmet had an AIS for head injuries of more than 2. The use of a protective helmet significantly reduced the severity of head injuries. The level of awareness towards danger and a history of previous accidents correlate with the likelihood of future accidents. Due to the severity of traffic accidents, more adequate prevention measures (wearing of bicycle helmets and better education for moped riders) are urgently needed.
To date, the Trauma Registry (TraumaRegister DGU-® contains data of approximately 100.000 severely injured patients, 65% of which suffered from a road traffic crash. Thus, it is the world's largest data base for severely injured patients. The article describes the development of the registry and explains how it was rolled out over Germany using the established structure of the German Trauma Network (TraumaNetzwerk DGU-®). In addition, this article presents three typical use cases from the fields of quality management, policy making and system-wide interventions, clinical research and injury prevention. In conclusion, the TraumaRegister DGU-® is a well-established tool for various purposes related to the control and reduction of the burden of road injury. Its ongoing expansion to other countries will support the goal of international benchmarking of hospitals and trauma systems.
Gegenstand der Untersuchung, bei dem die Blutalkoholuntersuchungsbefunde des Instituts für Rechtsmedizin der Universität Bonn aus den Jahren 1997, 1999 und 2003 retrospektiv ausgewertet wurden, war zum einen die Frage nach dem Frauenanteil und der Beteiligung von Alkoholikern an der Trunkenheitsdelinquenz im Straßenverkehr. Zum anderen sollte nachvollzogen werden, inwieweit die im Laborversuch ermittelten Konversionsfaktoren bei der Anwendung in der polizeilichen Praxis bestätigt werden können. In der wissenschaftlichen Diskussion der pharmakokinetischen Grundlagen wurden nach Trinkversuchen unter Laborbedingungen Zweifel an einer ausreichend gesicherten Korrelation zwischen Atem- und Blutalkoholkonzentration geäussert. Die Auswertung von 1.889 Datensätzen mit dem Ziel der Analyse der Zusammenhänge zwischen Blut- und Atemalkoholkonzentration in der Praxis ergab im Vergleich zu einer früheren Studie, dass die Resultate innerhalb enger Grenzen übereinstimmen und sie die Verhältnisse im tatsächlichen polizeilichen Einsatz abbilden. Bei der Geschlechterverteilung ergab sich ein Frauenanteil von 9 Prozent, bei mindestens 7 Prozent der Teilnehmer ist eine Alkoholproblematik zu vermuten.
In der Vergangenheit stiegen die Verkehrsbelastung und der Anteil des Schwerverkehrs auf deutschen Straßen und Autobahnen nahezu stetig. Dies wird sich auch in der Zukunft fortsetzen. Um auch zukünftig Mobilität gewährleisten zu können, sind Bauweisen mit maximaler Nutzungsdauer und minimalen Erhaltungsaufwendungen erforderlich. In Deutschland werden Betonfahrbahndecken als unbewehrte direkt befahrene Betonfahrbahnplatten mit Querfugen in regelmäßigen Abständen gefertigt und für Nutzungsdauern von 30 Jahren konzipiert. Die Querfugen stellen dabei den schwächsten Bereich in der Konstruktion dar. Betonfahrbahndecken können auch als Durchgehend Bewehrte Betonfahrbahndecke gefertigt werden. Dabei stellt sich ein freies Rissbild mit schmalen Plattenstreifen ein. Um eine Querkraftübertragung zu sichern, wird die Rissöffnungsweite durch die Anordnung einer durchgehenden Längsbewehrung beschränkt. Die Erfahrungen zeigen, dass mit dieser Bauweise eine längere Nutzungsdauer und ein höherer Fahrkomfort erreicht werden und weniger Erhaltungsmaßnahmen erforderlich sind. Durchgehend Bewehrte Betondecken eignen sich besonders gut für eine Asphaltüberbauung, da es keine Querfugen als Störstellen gibt. Diese Komposition hat das Potenzial für eine Nutzungsdauer von 50 Jahren und erfordert geringere Kosten, wenn man den gesamten Lebenszyklus betrachtet. Um baupraktische Erfahrungen zu sammeln, wurde im Jahr 2011 auf der Bundesautobahn (BAB) A 94 bei Forstinning in Bayern eine Versuchsstrecke eingerichtet. Diese besteht aus drei Abschnitten von je etwa 4 km Länge: Durchgehend Bewehrte Betondecke mit DSH-V-Überbauung, unbewehrte Betondecke in Plattenbauweise mit DSH-V-Überbauung und unbewehrte Betondecke in Plattenbauweise mit Grinding-Oberfläche. Erste Ergebnisse bezüglich Rissbildung, Bewegungen an den Endspornen, Haftverhalten des Blacktopping und der Schallmessungen liegen vor.
Methods for analyzing the efficiency of primary safety measures based on real life accident data
(2009)
Primary safety measures are designed to help to avoid accidents or, if this is not possible, to stabilize respectively reduce the dynamics of the vehicle to such an extent that the secondary safety measures are able to act as good as possible. The efficiency of a primary safety measure is a criterion for the effectiveness, with which a system of primary safety succeeds in avoiding or mitigation the severity of accidents within its range of operation and in interactionwith driver and vehicle. Based on Daimler-´s philosophy of the "Real Life Safety" the reflection of the real world accidents in the systems range of operation is both starting point as well as benchmark for its optimization. This paper deals with the methodology to perform assessments of statistical representative efficiency of primary safety measures. To be able to carry out an investigation concerning the efficiency of a primary safety measure in a transparent and comparable way basic definitions and systematics were introduced. Based on these definitions different systematic methods for estimating efficiency were discussed and related to each other. The paper is completed by presenting an example for estimating the efficiency of actual "single" and "multi" connected primary safety systems.
Relevant accident related factors : risk and frequencies of contributing to road traffic accidents
(2009)
In the course of the European Project TRACE (Traffic Accident Causation in Europe) an attempt was made to analyse the cause of road traffic accidents from a factors' point of view. By literature review the most important independent risk factors for traffic accidents were identified to be speed, alcohol intake, male gender, young age, cell phone use, and fatigue. However, the impact of an accident related factor also depends on its prevalence in traffic and accidents, respectively. Available to the Partners in the TRACE Project were different accident databases. Causally contributing factors found by accident investigations that are most often coded in accident databases are connected to unadapted speed and inattention. Taking into account the risk increase and the frequency of contribution to accidents the conclusion can be drawn that the most relevant factors for accident causation are: "alcohol", "speed", and "inattention and distraction".
Females sustain Cervical Spine Distortion injury (CSD) more often than males. Most work dealing with the biomechanics background (e.g. injury mechanism/criteria) as well as the application in seat design/testing, focuses on the occupant model of an average male. Therefore the EU-Project ADSEAT (Adaptive Seat to Reduce Neck Injuries for Female and Male Occupants) is aimed at adding a female model for gender balanced research of CSD and improving seat design. An extensive literature review, searching for risk factors and injury criteria for males and females, was accompanied by the evaluation of different databases containing CSD cases. The database evaluations suggests that an anthropometry quite close to the 50%ile female anthropometry as known from crash test dummy design is appropriate. The results presented here form the basis for the future development of a computational female model and the improvement of seat design for better protection of both males and females in the frame of the ADSEAT-Project.
In the course of the EUROPEAN PROJECT TRACE all fatally injured pedestrians autopsied at the Institute for Legal Medicine in Munich in 2004 had been analysed by using the "Human Functional Failure (HFF) analysis" method. It was possible to apply this method although some restrictions have to be taken into account. The results derived from this analysis comprise first the failures the pedestrians (most often "impairment of sensorimotor and cognitive abilities") and the opponents (most often " Non-detection in visibility constraints conditions") faced in the accident, second the conflicts and tasks (pedestrian crossing the street conflicting with a vehicle from the side (which was going ahead on a straight road), the degree of accident involvement (pedestrians often the primary active part), and further the contributing factors to the accident (pedestrians most often "alcohol (> 0.05% BAC)", opponents most often "visibility constraints").
The Netherlands is on the way to change its existing skid resistance measuring method for its highway network from the Dutch RAW 72, a longitudinal force method, to the Sideway Force method. This method is described in the Technical Specification 15901-8 (SKM device) as well as 15901-6 (SCRIM device) and is in use in 9 European countries. The CEN TC 227 WG5 on Surface Characteristics is currently working on combining of these two technical Specifications into a European standard for Sideway-Force (SWF) measurement devices. The idea of this change in the Netherlands was perceived in 2013 and since then a lot of meetings have been held with the different Dutch decision makers as well as with countries which currently operate SWF devices. There was an intensive exchange of knowledge about these devices and their corresponding quality assurance systems, because the Netherlands wanted to incorporate and rely on an existing system of a neighbor country without losing their present level of quality. The Netherlands has therefore decided to incorporate the German SKM approach. The network monitoring with the new system will start in 2017. To ensure the quality of skid resistance measurements and further cooperation in this field, it has been decided to initiate an alliance between BASt and the Dutch road owner Rijkswaterstaat (RWS). This alliance will facilitate an exchange of research activities, calibration of the Dutch systems according to the existing German Standard as well as control measurements with a BASt-device on the Dutch network during the network monitoring. During 2016 also comparative measurements will be performed on a network level with the current Dutch device and with an SKM device to determine a conversion between the two and to be able to define new threshold values.
Seilverspannte Brücken
(2008)
Der Beitrag behandelt den Entwurf, Besonderheiten der Berechnung und die Bemessung der beiden wichtigsten Bauarten seilverspannter Brücken, der echten Hängebrücke und der Schrägseilbrücke. Bei den Hängebrücken wird zunächst eingegangen auf die geschichtliche Entwicklung, die geprägt ist durch die im Zuge der Verbesserung des Stahls zunehmende Drahtfestigkeit. Anschliessend geht der Bericht ein auf: statisches System, Arten des Ueberbaus, Ausführung der Pylone, Kabel, Hänger und Widerlager. Analog zu den Hängebrücken ist der Beitrag bei den Schrägseilbrücken aufgebaut: geschichtliche Entwicklung, Haupttragwerke, Ueberbau, Pylone und Schrägseile. Hinsichtlich der Besonderheiten der Berechnung werden angesprochen: Anwendung der Theorie II. Ordnung und Betriebsfestigkeitsbeanspruchung. Erläutert wird auch die Montage sowohl der Hängebrücke als auch der Schrägseilbrücke in Wort und Bild.
Cyclists are more likely to be injured in fatal crashes than motorised vehicles. To gain detailed and precise behavioural data of road users, i.e. trajectories, a measuring campaign was conducted. Therefore, a black-spot for accidents with cyclists in Berlin, Germany was selected. The traffic has been detected by a fully automated traffic video analysis system continuously for twelve hours. The video surveillance system is capable of automatically extracting trajectories, classifying road user types and precise determining and positioning of conflicts and accidents. Additionally, pre-conflict and pre-accident situations could be analysed to provide further in-depth understanding of accident causation. The evaluation of the measuring campaign comprised the investigation of traffic parameters, e.g. traffic flow, as well as traffic-safety related parameters based on Surrogate Safety Measures (SSM). Furthermore, the spatial and temporal distributions of conflicts involving cyclists were determined. As a result, three possible conflict clusters could be identified, of which one cluster could be confirmed by detailed video analysis, showing conflicts caused by right turning vehicles.
In an on-going project since 2005, ADAC has been analyzing accidents documented by the ADAC air rescue service. The knowledge derived from real-life accidents serves as a basis for new test configurations and assessment criteria. In 2007, ADAC began looking into the feasibility of international data collection. The idea of Global Accident Prevention was born. Three European partner clubs have begun pioneering the project (ÖAMTC, ANWB, and RACC). The aim is to set up an international accident research network to provide a steady stream of information on road accidents. The FIA Foundation supports ADAC in developing and coordinating this initiative.
Active safety systems are aimed at accident prevention, hence the knowledge required for their development is different from that required for passive safety systems aimed at injury prevention. Particularly, knowledge about accident causation is required. When looking at existing accident causation data, it is argued it fails to explain in sufficient detail how and why the accidents occur. Therefore, there is a need for detailed micro-level descriptions of accident causation mechanisms, and also of methodologies suitable for creating such descriptions. One study addressing these needs is the Swedish project FICA (Factors Influencing the Causation of Accidents and Incidents), where an accident investigation methodology suitable for active safety is developed, and in-depth accident investigations following this methodology are carried out on-scene in the area of Gothenburg by a multidisciplinary team. A preliminary aggregated analysis of different cases shows that the methodology developed is adequate for pointing out common contributing factors and devising principal countermeasures.
In Finland all fatal motor vehicle accidents are studied in-depth on-the-spot by multidisciplinary (police, road and vehicle engineers, physician and behavioural scientist) road accident investigation teams (legislation 2001, work started 1968), which operate in every province. The purpose of the teams is to uncover risk factors that turned an ordinary driving situation into a serious accident and give safety recommendations for improving road safety. The investigation teams do not take a stand on guilt or insurance compensation. When analysing accidents the teams use the concepts of key event, immediate, background and injury risk factors. Compiled investigation folders of each case contain investigation forms from each member, preinvestigation protocol, photographs, sketches etc. About 500 items of information are collected from each accident party. The collected information is also coded into a computer database. Both the database and the investigation folders are widely utilized by researchers and authorities conducting safety work.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
Mit der Gründung des Bundesamtes für Strassen (ASTRA) im Jahr 1998 wurde ein wichtiges Signal gesetzt, das den Weg hin zu einer einheitlichen Vorgehensweise im Bereich der verkehrsmedizinischen Begutachtung in der Schweiz belebte. Der im Jahr 2000 veröffentlichte Leitfaden über die Verdachtsgründe der fehlenden Fahreignung, das In-Kraft-Treten des neues Straßenverkehrsgesetzes am 01.10.2005 (mit dem Herabsetzen der verkehrsrelevanten Alkoholpromillegrenze von 0,8 Promille auf 0,5 Promille, der Einführung einer Nulltoleranz für bestimmte Drogen, der Verschärfung der Administrativmaßnahmen und der strafrechtlichen Sanktionen sowie der anlassfreien Alkoholkontrolle als generalpräventiver Maßnahme) und die Veröffentlichung des Handbuchs der verkehrsmedizinischen Begutachtung durch die Arbeitsgruppe Verkehrsmedizin der Schweizerischen Gesellschaft für Rechtsmedizin im Jahr 2005, waren wichtige Meilensteine auf dem Weg zu einer einheitlichen Vorgehensweise im Bereich der verkehrsmedizinischen Begutachtung in der Schweiz.
Mobil sein zählt zu den Grundbedürfnissen und im Rahmen des westlichen Wertesystems zu den Grundrechten von Menschen. Dies gilt umso mehr, je mobiler die Gesamtgesellschaft wird und je mehr Menschen im Zuge der demographischen Entwicklung zum Kreis der "älteren Menschen" zählen. Dementsprechend wertet der dritte Bericht zur Lage der älteren Generation in der Bundesrepublik Deutschland den Erhalt der Mobilität im Alter als Basis für die "Erschließbarkeit der verschiedensten Ressourcen der Außenwelt" und als "entscheidenden Faktor von Lebensqualität im Alter", d.h. Aufrechterhaltung der Unabhängigkeit der Lebensführung durch Bewahrung von Fertigkeiten inkl. der Ermutigung zur Mobilität spielt für Ältere eine besonders wichtige Rolle. Die Entwicklung von Interventionsansätzen zur Förderung einer lebenslangen, sicheren Mobilität älterer Menschen stellt eine gesamtgesellschaftliche Herausforderung dar. Dementsprechend lebendig ist die Diskussion über Möglichkeiten ältere Verkehrsteilnehmer/innen in der Erhaltung ihrer Mobilität zu unterstützen und die Forschungsaktivität auf diesem Gebiet. Im Vortrag werden u. a. folgende Bereiche thematisiert: - Senioren stellen keine homogene Gruppe dar; dieses gut erforschte Faktum gilt auch für ihr Mobilitätsverhalten, aber auch für das Risikoverhalten. Ältere Menschen sind durch ausgesprochene Vielfalt mobilitätsbezogener Erwartungen, Verhaltensmuster und Lebensstile charakterisiert. - Die gegenwärtig durchaus wachsende positive Bewertung und Einstellung gegenüber Alter und Altern muss bei der Entwicklung neuer Sicherheitsmodelle berücksichtigt werden, gar Vorteil sollte daraus gezogen werden. - Um höhere Straßenverkehrssicherheit - nicht nur für Ältere - zu erreichen, ist eine stärkere Orientierung auf schwache, ungeschützte, vulnerable Verkehrsteilnehmer notwendig. - Teilnahme am Straßenverkehr ist Ergebnis eines lebenslangen Lernprozesses. Mobilitätsgewohnheiten, die während des Lebenslaufes erworben wurden, werden auch im Alter (unter Einsatz diverser Kompensationsstrategien) zum Großteil beibehalten. - Technologische Systeme (z.B. Telematik) können Mobilitätsplanung erleichtern und (bis zu einem gewissen Grad) Verluste in Fertigkeiten und Fähigkeiten zur Verkehrsteilnahme kompensieren und auf diese Weise zur Unfallreduktion beitragen. Die Alterssensitivität der Systeme muss ein zentraler Entwicklungsbereich sein. - Es sollte eine sehr viel stärkere Beteiligung der Älteren an der Entwicklung, Einführung und Implementation von verkehrsbezogenen Sicherheitsmaßnahmen und neuen Technologien ermöglicht werden. - Augenmerk sollte auch auf "alternative" Mobilitätsformen gelenkt werden: Smart Modes (zu Fuß gehen, Radfahren). Auch die Nutzung des ÖPNV sollte dadurch erleichtert werden, dass er so "benutzerfreundlich" wie nur möglich wird. - Ältere haben weiterhin ein hohes Interesse an und eine positive Einstellung zu Lernen, Übung und Training. Dies gilt auch für technischen Fortschritt und moderne Entwicklungen bezüglich der Straßenverkehrssicherheit. - Wenn Verkehrssicherheitsmaßnahmen implementiert werden, sollten die Kommunikationsmöglichkeiten dergestalt genutzt werden, dass sie für die verschiedenen Lebenssituationen und Lebensstile der Älteren angemessen sind. "Neue" Medien können dabei durchaus in Betracht gezogen werden. Fachdisziplinen wie Politikwissenschaft, Verkehrswesen, Ingenieurwissenschaften, Raumplanung, Architektur, Soziologie, Medizin, Psychologie, Pädagogik, Rechtswissenschaften, Ökonomie und Ökologie müssen künftig kooperieren, um einen Synergie-Effekt im Bereich der Mobilitätsförderung und der Verkehrssicherheitsarbeit für ältere Verkehrsteilnehmer und Verkehrsteilnehmerinnen zu erzielen. Dabei ist eine enge, interdisziplinäre Zusammenarbeit notwendig - ebenso wie ein vorurteilsfreier Umgang der Menschen miteinander in unserer Gesellschaft.
Recent findings from real-world accident data have shown that fatality risks for pedestrians are substantially lower than generally reported in the traffic safety literature. One of the keys to this insight has been the large and random sample of car-to-pedestrian crashes available in the German In-Depth Accident Study (GIDAS). Another key factor has been the proper use of weight factors in order to adjust for outcome-based sampling bias in the accident data. However, a third factor, a priori of unknown importance, has not yet been properly analysed. This is the influence of errors in impact speed estimation. In this study, we derived a statistical model of the impact speed errors for pedestrian accidents present in the GIDAS database. The error model was then applied to investigate the effect of the estimation error on the pedestrian fatality risk as a function of car impact speed. To this end, we applied a method known as the SIMulation-EXtrapolation (SIMEX) method. It was found that the risk curve is fairly tolerant to some amount of random measurement error, but that it does become flattened. It is therefore important that the accident investigations and reconstructions are of high quality to assure that systematic errors are minimised and that the random errors are under control.
An approach to the standardization of accident and injury registration systems (STAIRS) in Europe
(1998)
STAIRS is a European Commission funded study whose aim is to produce a set of guidelines for a harmonised, crash injury database. The need to evaluate the effectiveness of the forthcoming European Union front and side impact directives has emphasised the need for real world crash injury data-sets that can be representative of the crash population throughout Europe. STAIRS will provide a methodology to achieve this. The ultimate aim of STAIRS is to produce a set of data collection tools which will aid decision making on vehicle crashworthiness as well as providing a means to evaluate the effectiveness of safety regulations. This paper will disseminate the up-to-date findings of the group as they try to harmonise their methods. The stage has been reached where studies into the diverse methods of the UK, French and German systems of crash injury investigation have been undertaken. An assessment has already been made of the relationships between the three current systems in order to define the areas of agreement and divergence. The conclusions reached stated that there were many areas that are already closely related and that the differences were only at the detailed level. With the emphasis on secondary safety and injury causation, core data sets were decided upon, taking into account: vehicle description, collision configuration, structural response of vehicles, restraint and airbag performance, child restraint performance, Euro NCAP, pedestrian and vehicle occupant kinematics, injury description and causation. Each variable was studied objectively, the important elements isolated and developed into a form that all partners were agreeable on. A glossary of terms is being developed as the project progresses which includes ISO standards and other definitions from the associated CAREPLUS project, which addresses the comparability of national data sets. A major consideration of the group was the data collection method to be employed. The strengths and weaknesses of each study were investigated to obtain a clear idea of which aspects offered the best way forward. The quality of this information and transference into a common format, as well as the necessary error checking systems to be employed have just been completed and are described. In tandem with this area of study the problem of the statistical relationship of each sample to the national population is also being investigated. The study proposes a mechanism to use a sample of crash injury data to represent the national and international crash injury problem