Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (337) (entfernen)
Schlagworte
- Conference (253)
- Konferenz (252)
- Accident (137)
- Unfall (137)
- Germany (134)
- Deutschland (131)
- Injury (101)
- Verletzung (100)
- Unfallrekonstruktion (73)
- Analyse (math) (61)
Institut
- Sonstige (337) (entfernen)
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
The incidence and treatment of sternal fractures among traffic accidents are of increasing importance to ensure best possible outcomes. Analysis of technical indicators of the collision, preclinical and clinical data of patients with sterna fractures from 1985-2004 among 42,055 injured patients were assessed by an Accident Research Unit. Two time groups were categorized: 1985-1994 (A) vs. 1995-2004 (B). 267/42,055 patients (0.64%) suffered a sterna fracture. Regarding the vehicle type, the majority occurred after car accidents in 0.81% (251/31,183 pts), followed by 0.19% (5/2,633pts) driving motorbike, and 0.11% (4/3,258pts) driving a truck. 91% wore a safety belt. Only 13% of all passengers suffering a sternal fracture had an airbag on board (33/255 car/trucks), with an airbag malfunction in 18%. The steering column was deformed in 39%, the steering wheel in 36%. Cars in the recent years were significantly older (7.67-±5 years (B) vs. 5.88-±5 years (A), p=0.003). Cervical spine injuries are frequent (23% vs. 22%), followed by multiple rib fractures (14% vs. 12%) and lung injuries (12% vs. 11%). We found 9/146 (6%) and 3/121 patients (3%) with heart contusion among the 267 sternal fractures. MAIS was 2.56-±1.3 vs. 2.62-±1.3 (A vs. B, p=0.349). 18% of patients were polytraumatized, with 11.2% dying at the scene, 2.3% in the hospital. Sternal fractures occur most often in old cars to seat-belted drivers often without any airbag. Severe multiple rib fractures and lung contusion are concomitant injuries in more than 10% each indicating the severity of the crash. Over a twentyyear period, the injury severity encountered was not different with 18% polytrauma patients suffering sternal fractures.
The European Union has set a target to reduce all road fatalities (over 40,000) with 50% in 2010. This target percentage remained unchanged with the introduction of the ten new member states within the EU as by May 1st, 2004. According to Eurostat, 34% of all fatalities in 1998 in the, then, fifteen states of the European Union were the result of single vehicle collisions. This represents over 14,000 lives lost each year of which many can likely be saved through better roadside infrastructure design. The challenge for road safety professionals is to find methods and design strategies that help to reduce these casualties. Procedures for full-scale vehicle crash testing of guard rails were first published in the US in 1962. Present European regulation is mainly based on these procedures and later developments. Since then the vehicle fleet has changed considerably. Due to the complexity of the actual safety problem the numerical simulation approach offers a good opportunity to evaluate the different parameters involved in road safety, such as infrastructure properties, vehicle type, vehicle occupants and injuries. The ideal situation would be that simulation tools are coupled or integrated and all involved effects would be related. At the moment this is not the case yet, but initiatives are taken and a new virtual era has started. This paper offers a method looking at two components that encompass the driving environment: the car and the guardrail. As part of the EC-funded project, RISER (Roadside Infrastructure for Safer European Roads) a multi body simulation program study is carried out to determine sensitivities of some parameters in car to guardrail collisions and gives insides in performance of the car with passive safety equipment, the guardrail and the interaction of these objects with each other. By offering a set of methods that includes these two aspects and their intertwining relations, more confidence can be gained in actually reducing fatalities due to single vehicle collisions with, or due to, roadside furniture. Reducing the number of fatalities of single vehicle crashes would contribute greatly to the stated goal of reducing casualties altogether.
Various kinds of demerit point systems have been developed and implemented in European countries, aimed at tackling repeat offences in road transport by acting as a deterrent and providing sanctioning. The impact of a demerit point system on the number of crashes is often reported to be significant, but temporary. The objective of the EU BestPoint project was to establish a set of recommended practices that would result in a more effective and sustainable contribution of demerit point systems to road safety. A high actual chance of losing the licence and a high perceived chance of losing the licence are basic prerequisites for the effective operation of demerit point systems. For measures applied within the context of a demerit point system, a four-step-approach is recommended: warning letter, driver improvement course, licence withdrawal, rehabilitation course. Further recommendations concern issues like points and offences, e.g. which offences should lead to points, target groups, and the administration of demerit point systems. The final result of the EU BestPoint project is a handbook (van Schagen & Machata, 2012) which provides a concise overview of all recommended practices. The presentation/paper outlines how sustainable safety improvements can be achieved if national demerit point systems are implemented and maintained according to the recommended practices. In addition, potential further steps towards an EU-wide demerit point system (cross-border exchange on points and/or offences) are presented.
The fact that ADAC Air Rescue handles approximately 4,000 road accident missions every year gave rise to set up an accident research programme for which ADAC Air Rescue provides its data. This data is of initial informational quality and will be supplemented by data from the police, experts, fire brigades as well as hospitals and forensic institutes. Although the number of cases is still rather low, certain tendencies can be identified. The causes for most accidents occur when joining or intersecting traffic, followed by speeding in road bends and tailgating. Many accidents involve HGV rear end collisions, often causing serious injuries, considerable damage and technical problems for the rescue operations. With regard to the various impact types, it has become obvious that most of the extremely serious injuries are inflicted during a passenger car side impact. In addition, access to and removal of trapped passengers is becoming more and more complicated, partly due to the increasing use of high-strength materials, and rescue operations tend to be more time consuming.
This study aimed at comparing head Wrap Around Distance (WAD) of Vulnerable Road User (VRU) obtained from the German in-depth Accident Database (GIDAS), the China in-depth Accident Database (CIDAS) and the Japanese in-depth Accident Database (ITARDA micro). Cumulative distribution of WAD of pedestrian and cyclist were obtained for each database (AIS2+) showing that WAD of cyclists were larger than the ones of pedestrians. Comparing three regions, the 50%tile WAD of GIDAS was larger than that of both Asian accident databases. Using linear regression that might predict WAD of pedestrians and cyclists from Impact speed and VRU height, WADs were calculated to be 206cm/219cm (Pedestrian/Cyclist) for GIDAS, 170cm/192cm for CIDAS and 211cm/235cm for ITARDA. In addition, this study may be helpful for reconsideration of WAD measurement alignment between accident reconstruction and test procedures.
Since 2008, the authors inspected fatal traffic accidents on the spot every year, with the cooperation of Toyota police station in Aichi pref. In the jurisdiction, numbers of fatal accidents were 18 in 2008, 12 in 2009, 14 accidents in 2010, and 16 in 2011. We here report the results of our analysis of information obtained by detailed inspection for those that occurred from 2008 to 2010. We focused on vehicle-to-pedestrian accidents, which accounted for about 45% of all accidents in 2008. Because many accidents occurred on residential roads not far from pedestrians" homes, it was revealed that the decrease of the collision speed by traffic calming such as humps and zone speed management, was highly effective. On the other hand, pedestrian detection technologies seemed to be also effective as a countermeasure on vehicle side. Every pedestrian position against a vehicle was clarified and TTC (Time to Collision) was calculated provisionally. Pedestrian accidents in intersections were also examined. Among the intersection pedestrian accidents within the jurisdiction, compared with the national average in Japan, the ratio of intersections without a signal and the ratio without a pedestrian crossing were high. According to the comparison of the Japanese traffic accident patterns between 2001 and 2008, pedestrian accidents during turning right and turning left did not decrease much. For elderly drivers, these accidents occurred very often. Finally, single vehicle accidents were analysed with the accident pattern analysis methods used above. There were high numbers of single vehicle accidents against object on single roads. Although fatal accidents against guardrails decreased, the numbers of fatal accidents against a utility pole and a sign pole were nearly constant. As for the impact with narrow width objects such as utility poles, the fatality rate was very high, and countermeasures of both road infrastructure and vehicles seem to be effective.
Driver distraction
(2017)
This report for the Institute of Advanced Motorists (IAM) summarises recent research and knowledge from scientific studies about distracted driving. The report defines what it means to be "distracted" when driving, discusses the impact of distraction on driver behaviour and safety, and what can be done to reduce distracted driving. The focus of distraction discussed here relates to how drivers engage with technology when driving. The report begins with a background to driver distraction, followed by discussion about what is actually meant by driver distraction. It is then considered why humans cannot successfully do two things at the same time, particularly within the context of driving. The subsequent section summarises the scientific research findings to date with regard to driver distraction and technology, and how this affects different types of road user. Recommendations for how driver distraction can be mitigated in the real world and a summary conclude the report. Responses to common questions raised by drivers are presented in Appendix A.
Immediate user self-evacuation is crucial in case of fire in road tunnels. This study investigated the effects of information with or without additional virtual reality (VR) behavioural training on self-evacuation during a simulated emergency situation in a road tunnel. Forty-three participants were randomly assigned to three groups with accumulating preventive training: The control group only filled in questionnaires, the informed group additionally read an information brochure on tunnel safety, and the VR training group received an additional behavioural training in a VR tunnel scenario. One week later, during the test session, all participants conducted a drive through a real road tunnel in which they were confronted with a collision of two vehicles and intense smoke. The informed and the behaviourally trained participants evacuated themselves more reliably from the tunnel than participants of the control group. Trained participants showed better and faster behavioural responses than informed only participants. Interestingly, the few participants in the control group who reacted adequately to the scenario were all female. A 1 year follow-up online questionnaire showed a decrease of safety knowledge, but still the trained group had somewhat more safety relevant knowledge than the two other groups. Information and especially VR behavioural training both seem promising to foster adequate self-evacuation during crisis situations in tunnels, although long term beneficial behavioural effects have to be demonstrated. Measures aiming to improve users/ behaviour should take individual difference such as gender into account.
Improving the security of critical road infrastructure is a major task for owners and operators of tunnels and bridges in the European TEN-T Network (Trans-European Networks of Transport) (European Parliament and Council 1996). Up to now, there has not been a systematic procedure for identifying and assessing critical infrastructure objects and selecting appropriate protection measures. The EC FP7 project SeRoN for the first time presents an innovative methodology in order to support road owners and operators in handling this complex task. This paper describes the methodology and project results in detail by giving an introduction into its practical application.
This paper deals with the determination of test criteria for the durability assessment of polyvinyl chloride (PVC)-based geosynthetic barriers (GBR-P) products in tunnel sealing systems. In the project different products for road tunnel application are investigated by systematic long time storage in hot water using a new test procedure based on SIA V 280 standard (test no. 13) and EN 14415. The objective of this research project is to derive suitable exposure conditions and criteria for a practical testing procedure with regard to service lifetimes of up to 100 years. For that test temperature and time as well as the best suitable test medium have been investigated in a structured way. To verify the results of the new test procedure the material properties of GBR-P samples removed from older road tunnels are investigated. Based on the presented results of the still on-going research program some preliminary conclusions regarding the updating of the German regulations for road tunnel sealing systems (ZTV-ING part 5 section 5 and TL/TP KDB) are given.
The first stage of the work has been to collate information on bridge assessment from the participating countries. In the later stages, the aim is to provide guidelines that reflect the current best practices, a methodology that will allow for future development and sufficient flexibility to accommodate variations in national priorities as the process of harmonisation is pursued. The following tasks fall within the scope of the project: (1) a review of current procedures and standards used for bridge assessment in Europe; (2) the development of models for taking into account the bridge specific traffic conditions and material properties; (3) the use of reliability methods based on a probabilistic approach for bridge assessment including the use of measurements for updating the reliability of structural elements; and (4) the provision of recommendations for methods and procedures that can be adopted for the assessment module of the management framework highlighting where further development will be beneficial.
In the project SECMAN " SECurity MANual " a simple four-step procedure for the identification of critical road infrastructures, assessment of these infrastructures regarding various man-made threats and the determination of effective protection measures was developed. These methodologies are summarized and combined into a comprehensive best-practice manual which allows for a trans-national structured and holistic security-risk-management approach for owners and operators of road infrastructures in Europe. This paper presents the developed methodology starting from the assessment procedures of a network's criticality over an object's attractiveness and vulnerability to the selection process of appropriate protection measures.
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
As the official German catalogue of accident causes has difficulty in matching the increasing demands for detailed psychologically relevant accident causation information, a new system, based on a "7 Steps" model, so called ACASS, for analyzing and collecting causation factors of traffic accidents, was implemented in GIDAS in the year 2008. A hierarchical system was developed, which describes the human causation factors in a chronological sequence (from the perception to concrete action errors), considering the logical sequence of basic human functions when reacting to a request for reaction. With the help of this system the human errors of accident participants can be adequately described, as the causes of each range of basic human functions may be divided into their characteristics (influence criteria) and further into specific indicators of these characteristics (e.g. distraction from inside the vehicle as a characteristic of an observation-error and the operation of devices as an indication for distraction from inside the vehicle. The causation factors accordingly classified can be recorded in an economic way as a number is assigned to each basic function, to each characteristic of that basic function and to each indicator of that characteristic. Thus each causation factor can be explicitly described by means of a code of numbers. In a similar way the causation factors based on the technology of the vehicle and the driving environment, which are also subdivided in an equally hierarchical system, can be tagged with a code. Since the causes of traffic accidents can consist of a variety of factors from different ranges and categories, it is possible to tag each accident participant with several causation factors. This also opens the possibility to not only assign causation factors to the accident causer in the sense of the law, but also to other participants involved in the accident, who may have contributed to the development of the accident. The hierarchical layout of the system and the collection of the causation factors with numerical codes allow for the possibility to code information on accident causes even if the causation factor is not known to its full extent or in full detail, given the possibility to code only those cause factors, which are known. Derived from the systematic of the analysis of human accident causes ("7 steps") and from the practical experiences of on-scene interviews of accident participants, a system was set in place, which offers the possibility to extensively record not only human causation factors in a structured form. Furthermore, the analysis of the human causation factors in such a structured way provides a tool, especially for on-scene accident investigations, to conduct the interview of accident participants effectively and in a structured way.
With an ever rising human life expectancy the share of elderly people in society is constantly rising. This leads to the fact that at the same rate the share of people with age related diseases such as dementia and poor eyesight taking part in traffic will rise and therefore traffic accidents caused by this group of people due to the disease will play an ever greater role. This Situation will be among the future challenges of road safety work. At present this study displays specific characteristics of accidents caused by elderly car drivers (aged 65 or higher) based on the analysis of the German In-Depth Accident Study GIDAS. Herein almost 1000 elderly car drivers were identified as accident participants in the years 2008 to 2011. The focus of this study lies on identifying special types of accidents which are caused by elderly drivers and on characterizing these types with the information gathered on scene and by interviewing the participants. The main evidence analyzed is the knowledge about the accident locality, the trajectories of the participants as well as the reasons for the occurrence of the accidents. Furthermore personal information such as the personal condition before the accident and driving purposes is used to identify patterns of contributing circumstances for accidents caused by elderly traffic participants.
In the context of this study, different data sources for accident research were examined regarding their possible data access and evaluated concerning the individual quality and extent of the data. Analyses of accidents require detailed and comprehensive information in particular concerning vehicle damages, injury patterns and descriptions of the accident sequence. The police documentation supplies the basic accident statistics and is amended in the context of the forensic treatment by further information, e.g. by medical and technical appraisals and witness questionings. As a new approach to the data acquisition for the analysis of fatal traffic accidents, the information was made usable which was collected by the police and by the investigations of the public prosecutor. The best strategy for obtaining reliable, extensive and complete data consists of combining the information from these two sources: the very complete, but elementary statistic data of the Niedersächsisches Landesamt für Statistik (Lower Saxony State Authority of Statistics), based on the police documentation as well as the very extensive accident information resulting from the investigation documentation of the public prosecutor after conclusion of the procedure, the so-called Court Records. Of all 715 fatal traffic accidents, which happened in the year 2003 in the German State of Lower Saxony, 238 cases were selected by means of a statistically coincidental selective procedure based on a statistically representative manner (every third accident). These cases cover the investigation documents of the 11 responsible public prosecutor- offices, which were requested and evaluated while preserving the data security. Of the 238 cases 202 cases were available, which were individually coded and stored in a data base using 160 variables. Thus a data base of a sample of representative data for fatal accidents in Lower Saxony was set up. The data base contains extensive information concerning general accident data (35 variables), concerning road and road surface data (30 variables), concerning vehicle-specific data (68 variables) as well as concerning personal and injury data (27 variables).
Within the COST Action TU1101 the working group WG 1 is dealing with acceptance criteria and problems in helmet use while bicycling concerning conspicuity, thermal stress, ventilation deficits and other potential confounding. To analyze the helmet usage practice of bicyclists in Europe a questionnaire was developed in the scope of working group 1 to collect relevant information by means of a field study. The questionnaire consists of some 66 questions covering the fields of personal data of the cyclist, riding und helmet usage habits, information concerning the helmet model and the sensation of the helmet, as well as information on previous bicycle accidents. A second complementary study is conducted to analyze if the use of a bicycle helmet influences the seating geometry and the posture of cyclists when riding a bicycle and if the if the helmet vertically limits the vision. For this purpose cyclists with and without helmets were photographed in real world situations and relevant geometrical values such as the decline of the torso, the head posture of the upper vertical vision limit due to the helmet were established from the photos. The interim results of the field studies which were conducted in Germany by the Hannover Medical School are presented in this study. Some 227 questionnaires were filled out, of which 67 participants had used a helmet and 42 of the 227 participants have had a bicycle accident before. For the analysis of the riding position and posture of the cyclist over 40 pictures of riders with a helmet and over 240 pictures of riders without a helmet were measured concerning the seating geometry to describe the influence of using a bicycle helmet. Some results in summary: From the riders interviewed with the questionnaire only 11% of the city bike riders and 12% of the mountain bike riders always used the helmet, while 38% of the racing bike riders and 88% of the e-bike-riders always used the helmet. The helmet use seems not to change the sensation of safety of cycling compared to the use of a car. The arguments for not wearing a helmet are mostly stated to be the short distance of a trip, high temperatures or carelessness and waste of time. The reasons for using a helmet are stated to be the feeling of safety and being used to using a helmet. Being a role model for others was also stated to be a reason for helmet use. Concerning the sensation of the helmet 9% of the riders reported problems with the field of vision when using a helmet, 57% saw the problem of sweating too much, and 10% reported headaches or other unpleasant symptoms like pressure on the forehead when using the helmet. The analysis of the seating posture from the pictures taken of cyclists revealed that older cyclists generally have a riding position where the handle bar is higher than the seat (0-° to 10-° incline from seat to handlebar), while younger riders had a higher variance (between -10-° decline and 20-° incline). Further, elderly riders and riders with helmets seem to have a more upright position of the upper body when cycling. The vertical vision limit due to the helmet is determined by the front rim of the helmet (mostly the sun shade). Typical values here range from 0-° (horizontal line from the eye to the sun shade) to 75-° upwards, in which elderly riders tend to have a slightly higher vertical vision limit possibly due to the helmet being worn more towards the face.
Although the statistics show a decreasing rate of child injuries and fatalities in German road accidents more efforts can be made to protect children in cars e.g. by developing appropriate child restraint systems. An important part in of this work can be achieved with the help of crash tests using child dummies. However these crash tests cannot completely reflect the situation of real world crashes as factors like children moving out of the optimal position or children incorrectly fastened by their parents are difficult to predict. Therefore this study gives an overview over the current accident and injury situation of child occupants in cars in German road accidents.
An increased use of bicycles comes along with an increased number of bicycle accidents. Bicycle accidents are more frequent than recorded by the police. To evaluate the real number of bicycle accidents during 12 months in Münster, Germany, injuries were collected by the Police and in each emergency unit anonymously. 2,153 patients had to be treated in a hospital, nearly triple the number of accidents that were registered by the police. Beside fractures of the upper extremities with major surgery, traumatic brain injuries were the leading cause for hospital admission. Bicycle helmet use can reduce traumatic brain injuries and the related number of deaths and hospital admissions. Laws on bicycle helmet might decrease the use of bicycles and therefore the reduction of positive health benefits. Other methods of accident prevention may lead to positive effects as helmet legislation as well, while having no reduction in bicycle use.