Sonstige
Filtern
Erscheinungsjahr
- 2015 (34) (entfernen)
Dokumenttyp
Sprache
- Englisch (34) (entfernen)
Volltext vorhanden
- ja (34) (entfernen)
Schlagworte
- Germany (34) (entfernen)
Institut
- Sonstige (34)
- Abteilung Fahrzeugtechnik (1)
Assessment of the effectiveness of Intersection Assistance Systems at urban and rural accident sites
(2015)
An Intersection Collision Avoidance System is a promising safety system for accident avoidance or injury mitigation at junctions. However, there is still a lack of evidence of the effectiveness, due to the missing real accident data concerning Advanced Driver Assistance Systems. The objective of this study is the assessment of the effectiveness of an Intersection Collision Avoidance System based on real accidents. The method used is called virtual pre-crash simulation. Accidents at junctions were reconstructed by using the numerical simulation software PC-Crashâ„¢. This first simulation is called the baseline simulation. In a second step the vehicles of these accidents were equipped with an Intersection Collision Avoidance System and simulated again. The second simulation is called the system simulation. In the system simulation two different sensors and four different intervention strategies were used, based on a time-to-collision approach. The effectiveness of Intersection Collision Avoidance System has been evaluated by using an assessment function. On average 9% of the reviewed junction accidents could have been avoided within the system simulations. The other simulation results clearly showed a change in the principal direction of force, delta-v and reduction of the injury severity.
Although the annual traffic accident statistics published by the national police is available in public, the detailed traffic accident data has not been released in Korea. Recently the Ministry of Land, Infrastructure and Transport recognized the importance of in-depth accident data to enhance road traffic safety and initiated a research project to establish a collection of the detailed accident data. The main objective of the project is a feasibility study to establish KIDAS (Korea In-Depth Accident Study). Within this project, three university hospitals which are located in mid-size cities have been selected to collect accident data. Annually, more than 500 cases of accidents have been collected from the in-patient's interviews and diagnosis. Unlike GIDAS (German In-Depth Accident Study), currently on-site investigation can"t be performed by the Korean police. The only available data is patient medical records, patient's description of accident circumstances and the damaged vehicle. Occasionally the police provide the accident investigation reports containing very brief information on accident causation and vehicle safety. In a first step, the concept of KIDAS is to adopt the format of iGLAD (Initiative for the Global Harmonization of Accident Data) for harmonization. Since the currently collected accident information is extremely limited compared with GIDAS, the other sources of data and calculations such as KNCAP vehicle data, pc-crash simulations, vehicle registration information, insurance company data are utilized to complete the iGLAD template. Results from KIDAS_iGLAD and the cases of assessment of active safety devices such as AEBS, ESC, and LDWS will be evaluated.
This study aimed at prediction of long bone fractures and assessment of lower extremity injury mechanisms in real world passenger car to pedestrian collision. For this purpose, two pedestrian accident cases with detail recorded lower limb injuries were reconstructed via combining MBS (Multi-body system) and FE (Finite element) methods. The code of PC Crash was used to determine the boundary conditions before collision, and then MBS models were used to reproduce the pedestrian kinematics and injuries during crash. Furthermore, a validated lower limb FE model was chosen to conduct reconstruction of injuries and prediction of long bone fracture via physical parameters of von Mises stress and bending moment. The injury outcomes from simulations were compared with hospital recorded injury data and the same long bone fracture patterns and positions can be observed. Moreover, the calculated long bone fracture tolerance corresponded to the outcome from cadaver tests. The result shows that FE model is capable to reproduce the dynamic injury process and is an effective tool to predict the risk of long bone fractures.
For the estimation of the benefit and effect of innovative Driver Assistance Systems (DAS) on the collision positions and by association on the accident severity, together with the economic benefit, it becomes necessary to simulate and evaluate a variety of virtual accidents with different start values (e.g. initial speed). Taken into account the effort necessary for a manual reconstruction, only an automated crash computation can be considered for this task. This paper explains the development of an automated crash computation based on GIDAS. The focus will be on the design of the virtual vehicle models, the method of the crash computation as well as exemplary applications of the automated crash computation. For the first time an automated crash computation of passenger car accidents has been realized. Using the automated crash computation different tasks within the field of vehicle safety can be elaborated. This includes, for example, the calculation of specific accident parameters (such as EES or delta-V) for various accident constellations and the estimation of the economic benefit of DAS using IRFs (Injury Risk Functions).
The Traffic Accident Research Institute at University of Technology Dresden investigates about 1,000 accidents annually in the area around and in Dresden. These datasets have been summarized and evaluated in the GIDAS (German Accident In-Depth Study) project for 13 years. During the project it became apparent that the specific traffic situation of a covert exit of a passenger car and an intersecting two-wheeler involves a high risk potential. This critical situation develops in a large part due to the lack of visibility between the driver and the intersecting bike. In this paper the accident avoidance potential of front camera systems with lateral field of view, which allows the driver to have an indirect sight into the crossing street area will be presented.
Within the overall system of novice driver preparation, the practical driving test plays an especially important role for the objective of improved driving safety: On the one hand, the test contents, assessment criteria and test results provide important orientation for the organisation of driving school training and the individual learning processes of the novice drivers (control function); on the other hand, the practical test serves to ensure that only novice drivers with adequate driving competence are entitled to participate in motorised road traffic (selection function). The aim of the present project is to elaborate a scientifically founded model for a future, optimised practical driving test, together with a contextual and methodical (implementation) concept for its continuous maintenance, quality assurance and further development. In addition, the institutional structures of the test system, test methods and test procedures - including the necessary demand, assessment, documentation and evaluation standards - are to be described in a "System Manual on Driver Licensing (Practical Test)". As a first step, selected psychology-based driving competence models and the contents of training and test documents are to be analysed. The results of this analysis will then serve as the starting point for a discussion of possibilities to model and measure driving competence, and for the outlining of a driving competence model for the theoretical determination of appropriate test content. Subsequently, demand standards for an optimised practical driving test can be derived by applying action theory principles to the demands of motor vehicle handling, and thereby defined as minimum personal standards for driving test candidates. This elaboration is to take into account not only latest knowledge from the fields of traffic and test psychology, but also relevant stipulations in licensing regulations, international trends in the further development of test standards, and novice-specific accident causes and competence deficits. A further outcome of the project - alongside theoretical-methodical foundations for optimisation of the practical driving test and for the draft of a system manual - is to be a "Catalogue of driving tasks (Category B)", in which the demand standards for the practical driving test are described in the form of situation-related driving tasks and situation-independent observation categories, as a means to specify the criteria for event-oriented performance assessment and overall competence evaluation. At the same time, criteria for the examiner's test decision are to be defined. This optimisation work will contribute, finally, to further development of the adaptive control strategy for the practical driving test. To enable implementation of the further developed demand, assessment and documentation standards of an optimised practical driving test, a contextual and methodical concept for an electronic test report is to be presented, together with an ergonomically founded design proposal for both hardware and software. The computer-assisted documentation of test performance is intended to support the driving test examiner in planning of the course of a driving test and assessment of the candidate's driving behaviour. Furthermore, optimisation of the performance feedback to candidates and improved possibilities for scientific evaluation of the optimised practical driving test are expected. With regard to test evaluation, a fundamental model is to be described, which - alongside monitoring of the psychometric quality criteria within the framework of an instrumental evaluation - incorporates an evaluation of test results, product audits and the responses to candidate and driving instructor surveys. Finally, the possible influence of driver assistance and accident avoidance systems on the realisation of a driving test and on the assessment of test performance is to be discussed.
High demands on exhaust emissions of passenger cars and light commercial vehicles require complex technologies. The three-way catalytic converter is an essential part of state of the art emission control systems. If a catalytic converter is damaged or its effectiveness deteriorates, it can be replaced by a replacement converter. Replacement catalytic converters from the aftermarket are approved on the basis of Regulation No 103 of the UNECE - United Nations Economic Commission for Europe. According to this regulation the replacement catalytic converter shall be designed, constructed and capable of being mounted so as to enable the vehicle to comply with the provisions taken as a basis for its type approval. Furthermore the pollution emissions must be effectively limited throughout the entire normal service life of the vehicle under normal operating conditions. In the context of the research project, the durability of replacement catalytic converters was examined. A VW Golf with emission standard Euro 4, 1.4 l petrol engine (55 kW) was selected as a test vehicle. At the start of the examinations, the vehicle showed a mileage of 75,000 km. The selected vehicle was regularly serviced in accordance with the manufacturer's specifications. No emission-relevant faults were recorded by the OBD system. The initial control measurement of the vehicle in as-delivered condition with the originally installed catalytic converter showed that the corresponding emissions of the regulated pollutants were considerably below the Euro 4 emission limits to be applied. Subsequently, an original replacement catalytic converter, which was purchased from an authorised dealer, and 4 catalytic converters purchased in the independent aftermarket, were examined. The replacement catalytic converters were conditioned according to the specifications of ECE Regulation No 103 and then measured in new condition. The catalytic converters were then aged on a burner test rig. Here a total mileage of 80,000 km was simulated. After 10,000 km and 40,000 km, the ageing was interrupted and the exhaust gas emissions of the test vehicle with the aged catalytic converters were measured. The examination was ended as soon as a limit value had been exceeded. The results of the project indicate that with the replacement systems for the after-treatment of exhaust gases available in the independent aftermarket, considerable quality differences can occur. At the end of the ageing over a distance of 80,000 km only the original replacement catalytic converter and one replacement catalytic converter from the independent aftermarket complied with the Euro 4 emission limits. With one replacement catalytic converter, the Euro 4 emission limits were already exceeded in new condition. With another replacement catalytic converter, the examination was aborted after 10,000 km ageing and with a further catalytic converter after 40,000 km ageing due to the Euro 4 emission limits being exceeded. The ECE Regulation No 103 provides for a test of durability of such systems over 80,000 km, but also alternatively enables the use of fixed deterioration factors. In practice, the durability of the replacement systems for the after-treatment of exhaust gases is guaranteed by their manufacturers. However, replacement catalytic converters are rarely inspected as part of the approval. In-use compliance provisions for replacement systems for the after-treatment of exhaust gases are not mentioned in the corresponding specifications. The results of this study indicate that the requirements in the ECE Regulation No 103 are not adequate to ensure the durability of replacement catalytic converters.
Mobility plays an important role in the Federal Republic of Germany. Motorised private transport and, consequently, passenger vehicles are the crucial factor. Vehicles should be environmentally and socially compatible yet also economically efficient at the same time. The crucial factor for pollution of the environment from road traffic is the exhaust emissions of the vehicles on the road. This is why, with the Directive 98/69/EC and the related introduction of exhaust emission standard Euro 3, the testing of the conformity of passenger and light commercial vehicles (in-service conformity check) was introduced. Vehicles already on the roads are to be examined again under type examination conditions (Type I Test) after a statistical selection process. In this way it is to be ensured that the systems and components relevant for the exhaust emissions of a vehicle will also function after several thousand kilometres. This is why the vehicles are checked again during in-service conformity check with respect to their limited pollution components. Due to the ever greater significance of CO2 emissions, both the CO2 emissions and the fuel consumption were included in this research project. For the success of such a project the choice of vehicle is of critical importance. Since this is the only way it is possible to also obtain a representative result. Therefore, in addition to the selection criteria required by law, statistical and technical criteria are also considered. The vehicle owners were selected on a random basis. All test vehicles were checked with respect to their pollutant components in the emissions laboratory in accordance with their standard. By law the same testing conditions apply in an in-service conformity check as in the relevant type approval. In this research project a total of 17 vehicle types were examined. Six types were equipped with positive-ignition engines and 11 types with compression ignition engines. Both groups were to each include vehicles of the limits Euro 4 and Euro 5. For vehicle types with positive-ignition engines, there was one type with the exhaust emission standard Euro 5. All others satisfied the exhaust emission standard Euro 4. For the vehicle types with compression ignition engines, 4 types satisfied exhaust emission standard Euro 5 and 7 types fulfilled exhaust emission standard Euro 4. Among the vehicle types with compression ignition and exhaust emission standard Euro4, there were 4 types of category M1 and 3 types of category N1 of class III. The aim of the research project is to examine the exhaust emissions in-service conformity of passenger and light commercial vehicles in operation to draw conclusions concerning the durability of engine components and systems for exhaust emission treatment. Overall in this in-service conformity testing programme, we were able, in accordance with the statistical procedure, to assess all 17 of the vehicle types tested as "positive". With the exception of one vehicle type, it was possible to conclude the random test for all vehicle types tested with the minimum random sample. This means that all 3 vehicles of one type in as-delivered condition complied with or fell below the respective limits for pollutant emissions according to the criteria of the statistical procedure. In the case of one vehicle type, where the random sample had to be enlarged, it was necessary to examine a total of 8 vehicles. Furthermore, with all vehicle types the CO2-emissions and fuel consumption (Type I Test) were determined to subsequently compare the measured CO2 emissions with those of the manufacturers. Of the 17 vehicle types examined, eleven vehicle types complied with the relevant manufacturers" values or fell below them. With six vehicle types, the CO2 emissions were more than the permissible 4% above the manufacturer- value during the Type I Test.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
Introduction: The method of causation analysis applied under the German accident survey GIDAS, which is based on Accident Causation Analysis System (ACAS) focuses on an on-scene data collection of predominantly directly event-related causation factors which were crucial in the accident emergence as situational resulting events and influences. The paradigm underlying this method refers to the findings of the psychological traffic accident research that most causally relevant features of the system components human, infrastructure and vehicle technology are found directly in the situation shortly before the accident. This justifies the survey method which is conducted directly at the accident (on-scene), shortly after the accident occurrence (in-time) with the detection of human-related causes (in-depth). Human aspects of the situation analysis that interact and influence the risk situations shortly before the collision are reported as errors, lapses, mistakes and failures in ACAS in specific categories and subcategories. Thus methodically ACAS is designed primarily for the collection of accident features on the level of operational action, which certainly leads to valid findings and behavioral causes of accidents. The enhancement by means of Moderating Conditions concerns the pre-crash phase in different levels: strategical, tactical and operational.