Abteilung Fahrzeugtechnik
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (23)
- Wissenschaftlicher Artikel (10)
- Arbeitspapier (7)
- Buch (Monographie) (5)
Schlagworte
- Evaluation (assessment) (45) (entfernen)
Institut
- Abteilung Fahrzeugtechnik (45) (entfernen)
Im Rahmen des weltweiten ESV-Programmes (Enhanced Safety of Vehicles) werden seit mehreren Jahren internationale Forschungsbemühungen unternommen (International Harmonized Research Activities, IHRA), um im Vorfeld der Gesetzgebung die wissenschaftlichen Grundlagen gemeinsam zu erarbeiten. Ziel der IHRA-Arbeiten ist es, auf der Grundlage dieser Forschungsergebnisse die Harmonisierung der Vorschriften zu erleichtern. Eine besondere Aktivität bezieht sich auf Intelligent Transportation Systems (ITS). Im vorliegenden Beitrag wird die Aufgabe dieser IHRA-ITS-Arbeiten geschildert, sowie der derzeitige Stand der Forschungsbemühungen beschrieben. Es zeigt sich, dass die beschriebene Sicherheitsbewertung eine Fülle von Fragestellungen aufwirft und weitere Forschungsanstrengungen erfordert. Die zukünftigen Bemühungen sind darauf gerichtet, in internationaler Zusammenarbeit und Arbeitsteilung die als besonders wichtig erkannten Themen zur Bewertung der fahrzeugseitigen Fahrerassistenzsysteme zu bearbeiten.
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
Dem Benzinverbrauch heutiger moderner Kraftfahrzeuge wird in zunehmendem Maße Beachtung geschenkt, um dem Konflikt zwischen Mobilität einerseits und Umweltschutz andererseits entgegenzuwirken. Ein Beitrag hierzu wird in der Reduzierung des Rollwiderstands der Bereifung mit einem Potential von bis zu 5 Prozent gesehen. Insbesondere bei Geschwindigkeiten unterhalb von 80 km/h dominierte der Roll- gegenüber dem Luftwiderstand. Bei der Bundesanstalt für Straßenwesen wurden Systeme und Verfahren für Messungen des Rollwiderstandes von Pkw-Reifen in einem Innentrommelprüfstand sowie mit einem Messanhänger entwickelt. In der vorliegenden Untersuchung wird gezielt der Frage nachgegangen, inwieweit Ergebnisse einer Messung im Prüfstand auf Ergebnisse einer Straßenmessung übertragen werden können und umgekehrt. Der Vergleich zeigt, dass die Messgenauigkeit mit dem Anhänger auf der Straße im Mittel geringer anzusetzen ist und erwartungsgemäß nicht die Aussagequalität von Messungen im Prüfstandsversuch erreicht wird. Dennoch weist jedes System Vorteile auf. So steht mit der Rollwiderstandsmessung im Prüfstand ein Verfahren zur Verfügung, bei dem als Schwerpunkt mehr der reifenseitige als der fahrbahnseitige Aspekt des Rollwiderstandes im Vordergrund steht. Hingegen kann mit dem Messanhänger vornehmlich der Einfluss der Oberflächeneigenschaften von verschiedenartigen Fahrbahnen untersucht werden. Beide Systeme ergänzen sich und können bei Fragestellungen zum Rollwiderstand sowohl von Reifen als auch von Fahrbahnoberflächen eingesetzt werden.
Die Untersuchung sollte erörtern, ob es empfehlenswert ist, das Testverfahren zum streifenden Anprall eines Motorradhelmes auf die Straßenoberfläche in die ECE-R 22 aufzunehmen. Dazu war zu klären, ob die Testmethode geeignet ist, rotatorische Kräfte auf den Prüfkopf zu erfassen und ob sich aufgrund der Unfallsituationen eine Notwendigkeit für ein solches Testverfahren ergibt. Die Messergebnisse zeigen, dass der Zusammenhang zwischen der verletzungswirksamen Rotationsbeschleunigung und der im Testverfahren gemessenen Tangentialkraft nicht ohne Zweifel belegbar ist. Somit wäre zu fordern, dass statt der Tangentialkraft die Rotationsbeschleunigung als Verletzungskriterium betrachtet wird. Dafür wird jedoch ein sehr hoher Anspruch an die Messtechnik im Labor gestellt. Aus der Sicht der Unfallforschung lässt sich sagen, dass bei derartigen Anprallsituationen, insbesondere bei Anprallgeschwindigkeiten von unter 40 km/h, die sich im Laborversuch realisieren lassen, nur mäßige Kopfverletzungen auftreten (AIS 2 oder geringer). Der hohe Aufwand des Testverfahrens scheint also nicht gerechtfertigt zu sein.
A biofidelic flexible pedestrian legform impactor (FlexPLI) has been developed from the year 2000 onwards and evaluated by a technical evaluation group (Flex-TEG) of UN-ECE GRSP. A recently established UN-ECE GRSP Informal Group on GTR9 Phase 2 is aiming at introducing the FlexPLI within world-wide regulations on pedestrian safety (Phase 2 of GTR No. 9 as well as the new UN regulation 127 on pedestrian safety) as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents. Besides, the FlexPLI has already been introduced within JNCAP and is on the Euro NCAP roadmap for 2014. Despite of the biofidelic properties in the knee and tibia sections, several open issues related to the FlexPLI, like the estimation of the cost benefit, the feasibility of vehicle compliance with the threshold values, the robustness of the impactor and of the test results, the comparability between prototype and production level and the finalization of certification corridors still needed to be solved. Furthermore, discussions with stakeholders about a harmonized lower legform to bumper test area are still going on. This paper describes several studies carried out by the Federal Highway Research Institute (BASt) regarding the benefit due to the introduction of the FlexPLI within legislation for type approval, the robustness of test results, the establishment of new assembly certification corridors and a proposal for a harmonized legform to bumper test area. Furthermore, a report on vehicle tests that previously had been carried out with three prototype legforms and were now being repeated using legforms with serial production status, is given. Finally, the paper gives a status report on the ongoing simulation and testing activities with respect to the development and evaluation of an improved test procedure with upper body mass for assessing pedestrian femur injuries.
Automated driving will provide many kinds of benefits - some direct and some indirect. The benefits originate at the individual level, from changes in the behaviour of drivers and travellers with regard to driving and mobility, ending up with benefits at the social level via changes in the whole transport system and society, where many of the current planning and operations paradigms are likely to be transformed by automated driving. There may also be disbenefits, particularly at a social level, for example in intensity of travel which could result in additional congestion and increased use of natural resources. There may also be unintended consequences. For example, we do not know the impacts on public transport: driverless vehicles could provide a means to a lower cost service provision, but the availability of automated cars could lead to more car travel at the expense of collective transport.
Established in 1997, the European New Car Assessment Programme (Euro NCAP) provides consumers with a safety performance assessment for the majority of the most popular cars in Europe. Thanks to its rigorous crash tests, Euro NCAP has rapidly become an important driver safety improvement to new cars. After ten years of rating vehicles, Euro NCAP felt that a change was necessary to stay in tune with rapidly emerging driver assistance and crash avoidance systems and to respond to shifting priorities in road safety. A new overall rating system was introduced that combines the most important aspects of vehicle safety under a single star rating. The overall rating system has allowed Euro NCAP to continue to push for better fitment and higher performance for vehicles sold on the European market. In the coming years, the safety rating is expected to play an important role in the support of the roll-out of highly automated vehicles.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
In spite of today's highly sophisticated crash test procedures like the different NCAP programs running world-wide, bad real world crash performance of cars is still an issue. There are crash situations which are not sufficiently represented by actual test configurations. This is especially true for car to car, as well as for car to object impacts. The paper describes reasons for this bad performance. The reasons are in principal bad structural interaction between the car and its impact partners (geometric incompatibility), unadjusted front end stiffness (stiffness incompatibility) and collapse of passenger compartments. To show the efficiency of improving cars' structural behaviour in accidents with different impact partners an accident data analysis has been taken out by members of European Project VC-COMPAT. Accident data analysis has shown that in Germany between 15,000 and 20,000 of the now severely injured car occupants might get less injured and between 600 and 900 car occupant fatalities might be saved. Similar results arise for the UK.
Statischer und dynamischer Fahrsimulator im Vergleich: Wahrnehmung von Abstand und Geschwindigkeit
(2016)
Die Methodik der experimentellen Fahrsimulation gewährleistet sichere Anwendungsforschung unter hoher Kontrollierbarkeit. Obwohl gegenwärtig viele Forschungsfragen in virtuellen Umgebungen beantwortet werden, existieren weder systematische Validierungsszenarien für Fahrsimulatoren, noch wurde die Vergleichbarkeit der Aussagekraft von Befunden aus Fahrsimulatoren mit und ohne Bewegungssystem bislang angemessen hinterfragt. Daher sollen in der vorliegenden Studie ein statischer und ein dynamischer Fahrsimulator hinsichtlich ihrer Validität in verschieden Fahrsituationen verglichen werden, wobei der Schwerpunkt auf Abstands- und Geschwindigkeitswahrnehmung liegt. Es wird erwartet, dass ein zusätzliches Bewegungssystem nur bei Fahraufgaben mit dynamischer Involvierung einen Redundanzgewinn für die Wahrnehmung des Fahrers liefert. Werden hingegen konstante Abstände eingehalten, sollten entsprechend der Hypothese beide Prüfumgebungen äquivalente Resultate zeigen. Insgesamt durchfuhren 60 Probanden Fahrszenarien zur Abstandsherstellung und -einschätzung, teils mit Okklusion, sowie Folgefahrten mit Beschleunigung und Verzögerung. Die Querführung wurde mithilfe einer Gassendurchfahrt untersucht. Indem die virtuelle Umgebung nach Vorbild einer real existierenden Teststrecke konstruiert wurde, kann ebenfalls auf reale Referenzwerte Bezug genommen werden. Die Ergebnisse weisen auf eine vergleichbare relative Validität zwischen statischem und dynamischem Simulator hin, wenn keine Kinetik in der Fahraufgabe vorhanden ist. In Beschleunigungssituationen bewirkt simulierte Fahrdynamik signifikante Wahrnehmungseinbußen, wobei das Bewegungssystem in Bremssituationen die Wahrnehmung signifikant unterstützt. In dem Querführungsszenario ist die Fahrgeschwindigkeit im statischen Simulator zwar signifikant höher und damit näher an der realen Referenz, allerdings wird im statischen Simulator eine auffällig nach rechts versetzte Spur gehalten. Dennoch, so der vorrangige Befund, sollte auch ein statischer Fahrsimulator valide Evaluationen für die meisten Fahraufgaben gewährleisten.