Abteilung Fahrzeugtechnik
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (90)
- Deutsch (51)
- Mehrsprachig (1)
Volltext vorhanden
- nein (142) (entfernen)
Schlagworte
- Safety (53)
- Sicherheit (53)
- Anfahrversuch (38)
- Vehicle (37)
- Bewertung (36)
- Evaluation (assessment) (36)
- Fahrzeug (36)
- Impact test (veh) (35)
- Test method (31)
- Prüfverfahren (29)
Institut
According to the German road traffic regulations children up to the age of 12 or a height below 150 cm have to use approved and appropriate child restraint systems (CRS). CRS must be approved according to UN-ECE Regulation No. 44. The regulation classifies CRS in 5 weight categories. The upper weight group is approved for children from 22 to 36 kg. However, studies show that already today many children weigh more than 36 kg although they have not reached a height of 150 cm. Therefore, no ECE R44 approved CRS is available for these overweight children. In conclusion, today's sizes and weights of children are no longer represented by the current version of the ECE R44. The heaviest used dummy (P10) weighs just 32.6 kg and has a height of 137.9 cm. Statistical data of German children show that already 5% of the children at a height of 137.9 cm have a weight above 45.3 kg. Regarding children at a height of 145 cm, the 95th percentile limit is at a weight of 53.3 kg. Based on these data 4 dummies with different heights and weights were defined and produced. Two of them are overweight. Up to now, there is no experience how current child restraint systems perform in a car crash if they are used by children with a weight above 36 kg and a height smaller than 150 cm. In the future, different child restraint systems will be tested with respect to the ECE R44 regulation using these overweight dummies.
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
The technology involved in traffic control in Germany has undergone significant changes. This paper describes how a group of German manufacturers have worked with operators to produce Open Communications Interface for Road Traffic Control Systems (OCIT). At the beginning of 2010, twenty-one different European manufacturers had bought licences for OCIT outstations.
The Joint Transport Research Centre of the Organisation for Economic Co-operation and Development and the International Transport Forum recently conducted a benchmarking study of the safety and productivity of typical highway transport trucks from various countries. This paper focuses on vehicle productivity and efficiency in regard to the movement of freight. Forty vehicles from 10 countries were examined. The vehicles were designed for longer-haul applications and were classified in three separate categories: workhorse vehicles, which are the most common and can travel on most roads; high-capacity vehicles, which may be restricted to a certain class of road; and very high-capacity vehicles, which may be restricted to specific highways or routes. The metrics used in the analysis include maximum cargo mass and volume capacity, optimum cargo density, fuel consumption, and carbon dioxide output as a function of the freight task. The study found that size and weight regulations have a significant effect on the productivity and efficiency of heavy vehicles, including fuel consumption and vehicle emissions per unit of cargo transported. Significant variations were found among the vehicles from participating countries as well as within vehicle classes. It was also apparent that, in general, higher-productivity vehicles are correlated more strongly with increased cargo volume than with increased cargo mass and that larger trucks are better suited to lower-density freight than are workhorse vehicles. The study also found that it is important to consider the freight task when evaluating vehicle fuel consumption and emissions.
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.
This paper describes the methodology for the assessment of the socio-economic impact of SAFESPOT applications. The applications selected for the assessment cover vehicle to vehicle (v2v) as well as vehicle to infrastructure (v2i) communication systems. The applications address main problem areas of road safety: accidents at intersections, accidents due to hazardous road and weather conditions and accidents due to over speeding and inappropriate distance. The assessment methodology relies in its core on cost-benefit analysis (CBA) as the most widespread tool to assess the profitability of applications form the society point of view. The assessment is however not limited to CBA but also considers the economic effects for particular stakeholder groups such as users, public authorities and the like. Their individual cost and benefits can be investigated in stakeholder analyses. Both elements, CBA and stakeholder analysis, form an integrated assessment approach which is applied here. The assessment makes use of the sound methodological base which was provided by projects such as SEiSS and eIMPACT. Some characteristics of co-operative systems however call for special attention within the assessment. Most prominently, the assessment will concentrate on a bundle of applications. The impact of this bundle will be assessed under the conditions of different business and service models. These issues will be addressed in the paper. Moreover, this paper also provides insight in likely patterns of results and first results of socio-economic impact assessment itself.
Mit der EU-Verordnung Nummer 661/2009 zur Typgenehmigung und allgemeinen Sicherheit von Kraftfahrzeugen wird von der EU für schwere Nutzfahrzeuge der Einbau von Spurverlassenswarnsystemen und automatischen Notbremssystemen vorgeschrieben. Mit dem obligatorischen Einbau der Systeme wird eine Reduktion der Abkommens- und Auffahrunfälle von Nutzfahrzeugen aus den Klassen M2, M3, N2 und N3, die auf Grund der hohen Masse der Fahrzeuge folgenschwer sind, erwartet. Als Einführungsdaten werden der 1. November 2013 für neue Fahrzeugtypen und der 1. November 2015 für neue Fahrzeuge genannt. Leistungsanforderungen beziehungsweise technische Spezifikationen, denen die Systeme genügen müssen, liegen jedoch noch nicht vor. Diese werden derzeit von einer Expertengruppe auf UN-ECE-Ebene entwickelt. Dabei wird versucht, technologieneutrale Beschreibungen für die Ausgestaltung der Systeme zu erstellen, die gleichzeitig sowohl den gewünschten Nutzen für die Verkehrssicherheit garantieren, sich aber auch an der derzeit vorhandenen und realisierbaren Technologie orientieren. Darüber hinaus müssen die Systemkosten in einem vernünftigen Verhältnis zum Sicherheitsnutzen stehen. Ziel ist es, im Laufe des Jahres 2011 Vorschläge für die Legislative vorzulegen. Es wird über den Stand der Arbeiten, offene Fragestellungen, Herausforderungen bei der Ausgestaltung der technischen Anforderungen sowie sich abzeichnende Ergebnisse berichtet. Dabei sind die Arbeiten in Bezug auf Lane Departure Warning Systems (LDWS) bereits weiter fortgeschritten als zu Advanced Emergency Braking Systems (AEBS).
Falltests zur Untersuchung der Belastungen von Dummys beim Aufprall auf den Boden, Teil 1 und 2
(2010)
Beim Zusammenprall eines Motorrads mit einem Pkw unterscheidet man in der Unfallforschung sowohl den Erstanprall des Motorradfahrers an den Pkw als auch den Sekundäraufprall des Motorradfahrers auf dem Boden. So genannte Full-Scale-Crashtests mit Dummys haben beim Erstanprall gezeigt, dass Motorradfahrer durch Airbags potenziell geschützt werden können. Bei den entsprechenden Unfallsimulationen wurde jedoch im weiteren Bewegungsablauf beim nachfolgenden Sekundäraufprall auf dem Boden festgestellt, dass relativ hohe Belastungen auf den Dummy einwirken. Es stellt sich hierbei jedoch die Frage, ob die üblicherweise für Lasteinwirkungen im Falle eines Erstanpralls entwickelten und validierten Dummys die bei einem Sekundäraufprall auf einen Motorradfahrer einwirkenden Belastungen hinreichend genau wiedergeben können. Dazu wurden die Belastungen eines Dummys beim Aufprall auf den Boden untersucht, um das Verletzungsrisiko eines menschlichen Motorradfahrers einschätzen zu können. Im Dekra-Crash-Test-Center wurden vier verschiedene Aufprallsituationen mit einem Hybrid III Dummy durchgeführt, wobei diese Tests an eine andere Testreihe angelehnt sind, die bereits am US-amerikanischen Institut "Dynamic Research International" (DRI) durchgeführt worden waren. Nach der Erläuterung des Testaufbaus und seiner Durchführung wird detailliert auf die gemessenen Verzögerungsbelastungen des Dummys eingegangen. Hierbei geben zum einen Tabellen eine Übersicht über charakteristische Messwerte zur Quantifizierung der maximalen Belastung des Dummys, zum anderen veranschaulichen Bilder die zugehörigen zeitlichen Verzögerungsverläufe in Becken, Brust und Kopf des Dummys. Der Artikel schließt mit einer Interpretation der Versuchsergebnisse und gibt einen Ausblick auf den weiteren Untersuchungsbedarf.
This article describes the development of techniques to minimize automobile driver distraction when an in-vehicle information systems (IVIS) that requires visual attention is in use. The authors explain the visual occlusion technique that has been developed as a tool for the assessment of the in-vehicle human-machine interface (HMI) of IVIS in terms of visual demands. The authors addressed an unresolved issue in previous standardized experimental protocols - how subjects make use of the occluded intervals and how this might affect the assessments of visual demands. This study protocol assumed that subjects would continue task performance during occluded periods, leading to an underestimation of visual demands by the occlusion parameters "total shutter open time" (TSOT) and the "occlusion index". The authors predicted that a simple additional loading task to be performed in parallel could disrupt IVIS task performance during the occluded period leading to higher estimations of visual demands by TSOT and R. Their prediction was confirmed by the study findings. The results also showed that under the condition of additional auditory tracking, TSOT and R discriminated more clearly between an "easy" and a "difficult" IVIS task than under the standard condition. They conclude with a discussion of the implications of this research for designers of assessment tools for driver visual distractions.