Filtern
Dokumenttyp
Schlagworte
- Fire (3)
- Tunnel (3)
- Abplatzen (2)
- Behaviour (2)
- Deutschland (2)
- Feuer (2)
- Forschungsbericht (2)
- Germany (2)
- Measurement (2)
- Messung (2)
- Research report (2)
- Spalling (2)
- Temperatur (2)
- Temperature (2)
- Test (2)
- Verhalten (2)
- Versuch (2)
- Abstandsregeltempomat (1)
- Accident (1)
- Accident prevention (1)
- Active safety system (1)
- Adaptive cruise controll (1)
- Air pollution (1)
- Aktives Sicherheitssystem (1)
- Auffahrunfall (1)
- Ausbreitung (1)
- Autobahn (1)
- Bemessung (1)
- Braking (1)
- Brand (1)
- Bremsung (1)
- Collision (1)
- Curve (math) (1)
- Decke (Straße) (1)
- Design (overall design) (1)
- Digital model (1)
- Driver (1)
- Education (1)
- Efficiency (1)
- Emergency (1)
- Environment (1)
- Erziehung (1)
- Fahrer (1)
- Faserbeton (1)
- Feinstaub (1)
- Fiber reinforced concrete (1)
- Full scale (1)
- Gas (1)
- Heat (1)
- Information (1)
- Kurve (math) (1)
- Leistungsfähigkeit (allg) (1)
- Luftverunreinigung (1)
- Method (1)
- Mix design (1)
- Motorway (1)
- Normalgröße (1)
- Notfall (1)
- Numerisches Modell (1)
- Particulate matter (1)
- Platte (1)
- Rear end collision (1)
- Simulation (1)
- Slab (1)
- Spreading (1)
- Surfacing (1)
- Temperature measurement (1)
- Temperaturmessung (1)
- Time (1)
- Tunnel lining (1)
- Tunnelauskleidung (1)
- Umwelt (1)
- Unfall (1)
- Unfallverhütung (1)
- Verfahren (1)
- Virtual reality (1)
- Virtuelle Realität (1)
- Wärme (1)
- Zeit (1)
- Zusammensetzung (1)
- Zusammenstoß (1)
Institut
- Sonstige (5) (entfernen)
Measuring and characterizing airborne particulate matter (PM) is an important research area because PM can lead to impacts on health and to visibility reduction, material damage and groundwater pollution. In regard to road dust, suspension and re-suspension and the contribution of non-exhaust PM to total traffic emissions are expected to increase as a result of predicted climate scenarios. European environmental regulations have been enforced to reduce exhaust particle emissions from road traffic, but little attention has been paid to reducing non-exhaust coarse particle emissions due to traffic. Therefore, a monitoring program for coarse PM has been initiated in early 2013 to assess the predicted increase in the abundance of non-exhaust particles. Particle sampling was performed with the passive-sampler technique Sigma-2. The subsequent single-particle analysis allows for characterization of individual particles, determination of PM size distribution, and calculation of PM mass concentrations. Two motorways n ear Cologne (Koeln), Germany were selected as sampling sites, and the experimental setup in the field was realized with a so-called twin-site method. The present study reports single-particle analysis data for samples collected between May 31, 2013 and May 30, 2014. Coarse PM, generated through multi-source mechanisms, consists of, e.g., tire-wear, soot aggregates, and mineral dust. The highest mass concentration occurs at both motorways in spring, and the observed PM mainly contains traffic-abrasion particles. The field measurements show that the minimum PM concentration was found in the 5 to 12-°C temperature range, whereas the maximum concentration was observed in both the "5 to 5-°C and the 12 to 24-°C ranges, in agreement with previous laboratory measurements. Correlation between super-coarse (d p 10"80 μm, geometric equivalent diameter) PM concentration and precipitation displays a significant increase in concentration with decreasing number of precipitation events (dry weather periods).
Immediate user self-evacuation is crucial in case of fire in road tunnels. This study investigated the effects of information with or without additional virtual reality (VR) behavioural training on self-evacuation during a simulated emergency situation in a road tunnel. Forty-three participants were randomly assigned to three groups with accumulating preventive training: The control group only filled in questionnaires, the informed group additionally read an information brochure on tunnel safety, and the VR training group received an additional behavioural training in a VR tunnel scenario. One week later, during the test session, all participants conducted a drive through a real road tunnel in which they were confronted with a collision of two vehicles and intense smoke. The informed and the behaviourally trained participants evacuated themselves more reliably from the tunnel than participants of the control group. Trained participants showed better and faster behavioural responses than informed only participants. Interestingly, the few participants in the control group who reacted adequately to the scenario were all female. A 1 year follow-up online questionnaire showed a decrease of safety knowledge, but still the trained group had somewhat more safety relevant knowledge than the two other groups. Information and especially VR behavioural training both seem promising to foster adequate self-evacuation during crisis situations in tunnels, although long term beneficial behavioural effects have to be demonstrated. Measures aiming to improve users/ behaviour should take individual difference such as gender into account.
Im Rahmen des Forschungsprojektes wurden für verschiedene Tunnel mit Rechteck- und Gewölbequerschnitt mit dem Regelquerschnitt RG 31t (bzw. RQ 10,5), die orts- und zeitabhängigen Verteilungen der Gastemperatur, der Gasgeschwindigkeit und Gaszusammensetzung, der adiabaten Decken- und Wandtemperaturen sowie der zeitliche Verlauf der Wärmefreisetzungsrate und des Durchwärmungsverhaltens bestimmt werden. Betrachtet wurden Tunnel mit konstanter Längsneigung von 3 % sowie ein Tunnel mit muldenfoermigem Längsprofil (Richtungs- und Gegenverkehr). Bezüglich der Austrittgeschwindigkeit wurden die Szenarien 20,6 kg/s und 300 kg/s unterschieden. Zusätzlich im Fall A ein mit Holzpaletten beladenen LKW und im Fall B zusätzlich noch weitere PKW und LKW berücksichtigt. In einem originalmaßstäblichen Großbrandversuch wurde zur Klärung offener, aus der Modellierung resultierender Fragen ein Unfall in einem Richtungsverkehrstunnel zwischen einem LKW, der mit ca. 3,7 t Europoolpaletten beladen war, und einem PKW nachgebildet. Insgesamt wurden 3 Mittelklasse-PKW im Versuchstunnel positioniert. Die Brandlast betrug ca. 123 GJ. Anhand durchgeführter Plattenbrandversuche wurde festgestellt, dass die Schichten aus spritzbarem Faserbeton des Systems RUB sowie die Fertigteilschutzschichten des Systems HOCHTIEF ein relativ geringes bzw. kein Abplatzverhalten aufweisen und bei Brandbeanspruchung jeweils einen signifikanten thermischen Schutz der Stahlbetonkonstruktion gewährleisten können. Es konnte gezeigt werden, dass Auswirkungen auf die Tragstruktur nicht größer sind als infolge eines Brands, dessen Temperatur-Zeit-Verlauf dem ZTV-ING-Verlauf entspricht. Es sei aber angemerkt, dass aus den Szenarien unter noch ungünstigeren Bedingungen (z.B. im Falle eingeschränkt funktionsfähiger Schlitzrinnen) Auswirkungen entstehen könnten, die nur durch den verlängerten ZTV-ING-Temperatur-Zeit-Verlauf abgedeckt wären.
Das Gesamtziel des Forschungsprojektes zum "Brand- und Abplatzverhalten von Faserbeton in Straßentunneln" war die Verifizierung und Validierung des Einflusses von Kunststofffasern auf das Brand- und Abplatzverhalten von Tunnelbetonen unter der besonderen Berücksichtigung der spezifischen Randbedingungen in Straßentunneln. Dabei sollte im Rahmen der Forschungsarbeit eruiert werden, inwieweit sich mit Kunststofffasern modifizierte Tunnelbetone, die entsprechend ihrer Betonzusammensetzung den gültigen Vorgaben der ZTV-ING zusammengesetzt werden sollten, für den Straßentunnelbau als bauliche Brandschutzmaßnahme eignen. Es wurde untersucht, welche Fasergehalte und Fasergeometrien in den Tunnelbetonen einzusetzen sind, damit ein explosionsartiges Abplatzen des Betons infolge der Brandbeanspruchungen mit dem schnellen Temperaturanstieg und den hohen Maximaltemperaturen verhindert werden kann. Des Weiteren wurden experimentell verifiziert, ob bei den festgelegten Betonen ohne Faserzugabe und fasermodifizierten Tunnelbetonen, die zulässige Maximaltemperatur von 300-°C in Höhe der tragenden Bewehrung (vergleiche ZTV-ING, Teil 5 (Tunnelbau), Abschnitt 1, 10.3.2) nicht überschritten wird. Ein weiteres Ziel der Arbeit war es, herauszufinden, ob die in der ZTV-ING, Teil 5, Abschnitt 2, 10.3.2 (2), geforderte verzinkte Mattenbewehrung (N94) für die offene Bauweise als wirksamer Schutz gegen auftretende Abplatzungen infolge einer einseitigen Temperaturbeanspruchung durch die ZTV-ING-Kurve angesetzt werden kann. Diese zuvor beschriebenen grundlegenden Zielstellungen wurden vor allem an großmaßstäblichen Bauteilversuchen experimentell untersucht. Dabei wurden entsprechend der Trennung in ZTV-ING für Tunnelbauwerke in die geschlossene Bauweise (ZTV-ING, Teil 5, Tunnelbau, Abschnitt 1 und in die offene Bauweise (ZTV-ING, Teil 5, Tunnelbau, Abschnitt 2) angepasste Tunnelbetonrezepturen und verschiedene Probekörpergeometrien untersucht. Mit der Durchführung des Forschungsprojektes sollte insgesamt der Nachweis des positiv wirksamen Einflusses von PP-Fasern auf das Brand- und Abplatzverhalten von ZTV-ING-konformen Tunnelbetonen für die Anwendung in Straßentunneln erbracht und zudem im Großversuch gezeigt werden, dass es möglich ist, fasermodifizierte Tunnelbetone mit Praxis üblichen Einbaukonsistenzen zielsicher herzustellen.
Methods for analyzing the efficiency of primary safety measures based on real life accident data
(2009)
Primary safety measures are designed to help to avoid accidents or, if this is not possible, to stabilize respectively reduce the dynamics of the vehicle to such an extent that the secondary safety measures are able to act as good as possible. The efficiency of a primary safety measure is a criterion for the effectiveness, with which a system of primary safety succeeds in avoiding or mitigation the severity of accidents within its range of operation and in interactionwith driver and vehicle. Based on Daimler-´s philosophy of the "Real Life Safety" the reflection of the real world accidents in the systems range of operation is both starting point as well as benchmark for its optimization. This paper deals with the methodology to perform assessments of statistical representative efficiency of primary safety measures. To be able to carry out an investigation concerning the efficiency of a primary safety measure in a transparent and comparable way basic definitions and systematics were introduced. Based on these definitions different systematic methods for estimating efficiency were discussed and related to each other. The paper is completed by presenting an example for estimating the efficiency of actual "single" and "multi" connected primary safety systems.