Filtern
Erscheinungsjahr
- 2007 (105) (entfernen)
Dokumenttyp
- Konferenzveröffentlichung (52)
- Buch (Monographie) (33)
- Wissenschaftlicher Artikel (16)
- Bericht (2)
- Teil eines Buches (Kapitel) (1)
- Arbeitspapier (1)
Schlagworte
- Conference (48)
- Konferenz (47)
- Germany (38)
- Deutschland (36)
- Sicherheit (31)
- Forschungsbericht (30)
- Research report (30)
- Safety (30)
- Accident (27)
- Unfall (26)
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 13. Oktober 2006 in Baden-Baden das 6. Symposium "Sicher fahren in Europa". Die Fachvorträge befassten sich mit den Themenbereichen: Ansätze zu mehr Verkehrssicherheit, - Verbesserung der Fahrzeugsicherheit, - Besondere Zielgruppen. Die CD-ROM dokumentiert die Grußworte, die Referate und die Podiumsdiskussion.
Today, Euro NCAP is a well established rating system for passive car safety. The significance of the ratings must however be evaluated by comparison with national accident data. For this purpose accidents with involvement of two passenger cars have been taken from the German National Road Accident Register (record years 1998 to 2004) to evaluate the results of the NCAP frontal impact test configuration. Injury data from both drivers involved in frontal car to car collisions have been sampled and have been compared, using a "Bradley Terry Model" which is well established in the area of paired comparisons. Confounders " like mass ratio of the cars involved, gender of the driver, etc. " have been accounted for in the statistical model. Applying the Bradley Terry Model to the national accident data the safety ranking from Euro NCAP has been validated (safety level: 1star <2 star <3 star <4 star). Significant safety differences are found between cars of the 1 and 2 star category as compared to cars of the 3 and 4 star category. The impact of the mass ratio was highly significant and most influential. Changing the mass ratio by an amount of 10% will raise the chance for the driver of the heavier car to get better off by about 18%. The impact of driver gender was again highly significant, showing a nearly 2 times lower injury risk for male drivers. With regard to the NCAP rating drivers of a high rated car are more than 2 times more probable (70% chance) to get off less injured in a frontal collision as compared to the driver of a low rated car.
Automotive Engineering, Mechanical Engineering and TechnologyrnAbstract: The degrees of injury severity, as a rule injuries scaled by AIS of specific regions of the human body, investigated out of road traffic accidents correspond to the body-specific loading values, which are found out with the aid of experimental or mathematical simulation of crash tests with motor vehicles or with sled tests. The coherence between the injured human being on the one hand and the physical and the theoretical model respectively on the other hand is established by the risk function, which describes the probability of degrees of injury severity in dependence on the protection criteria. Due to the different physical characteristics in the simulation, e.g. accelerations, forces, compressions and their velocity, the compilation of these quantities, comparable to the MAIS, the maximal occurred single AIS obtained in accident analysis is much more difficult in the simulation than in the accident occurrence. Therefore it is obvious to normalize the loading values gained out of simulation and to summarise them to an entire value in a suitable manner, the safety index.rn
The fact that ADAC Air Rescue handles approximately 4,000 road accident missions every year gave rise to set up an accident research programme for which ADAC Air Rescue provides its data. This data is of initial informational quality and will be supplemented by data from the police, experts, fire brigades as well as hospitals and forensic institutes. Although the number of cases is still rather low, certain tendencies can be identified. The causes for most accidents occur when joining or intersecting traffic, followed by speeding in road bends and tailgating. Many accidents involve HGV rear end collisions, often causing serious injuries, considerable damage and technical problems for the rescue operations. With regard to the various impact types, it has become obvious that most of the extremely serious injuries are inflicted during a passenger car side impact. In addition, access to and removal of trapped passengers is becoming more and more complicated, partly due to the increasing use of high-strength materials, and rescue operations tend to be more time consuming.
Bicyclists are minimally or unprotected road users. Their vulnerability results in a high injury risk despite their relatively low own speed. However, the actual injury situation of bicyclists has not been investigated very well so far. The purpose of this study was to analyze the actual injury situation of bicyclists in Germany to create a basis for effective preventive measures. Technical and medical data were prospectively collected shortly after the accident at the accident scenes and medical institutions providing care for the injured. Data of injured bicyclists from 1985 to 2003 were analyzed for the following parameters: collision opponent, collision type, collision speed (km/h), Abbreviated Injury Scale (AIS), Maximum AIS (MAIS), incidence of polytrauma (Injury Severity Score >16), incidence of death (death before end of first hospital stay). 4,264 injured bicyclists were included. 55% were male and 45% female. The age was grouped to preschool age in 0.9%, 6 to 12 years in 10.8%, 13 to 17 years in 10.4%, 18 to 64 years in 64.7%, and over 64 years in 13.2%. The MAIS was 1 in 78.8%, 2 in 17.0%, 3 in 3.0%, 4 in 0.6%, 5 in 0.4%, and 6 in 0.2%. The incidence of polytrauma was 0.9%, and the incidence of death was 0.5%. The incidence of injuries to different body regions was as follows: head, 47.8%; neck, 5.2%, thorax, 21%; upper extremities, 46.3%; abdomen, 5.8%; pelvis, 11.5%, lower extremities, 62.1%. The accident location was urban in 95.2%, and rural in 4.8%. The accidents happened during daylight in 82.4%, during night in 12.2%, and during dawn/dusk in 5.3%. The road situation was as follows: straight, 27.3%; bend, 3.0%; junction, 32.0%; crossing, 26.4%; gate, 5.9%; others, 5.4%. The collision opponents were cars in 65.8%, trucks in 7.2%, bicycles in 7.4%, standing objects in 8.8%, multiple objects in 4.3%, and others in 6.5%. The collision speed was grouped <31 in 77.9%, 31-50 in 4.9%, 51-70 in 3.7%, and >70 in 1.5%. The helmet use rate was 1.5%. 68% of the registered head injuries were located in the effective helmet protection area. In bicyclists, head and extremities are at high risk for injuries. The helmet use rate is unsatisfactorily low. Remarkably, two thirds of the head injuries could have been prevented by helmets. Accidents are concentrated to crossings, junctions and gates. A significant lower mean injury severity was observed in victims using separate bicycle lanes. These results do strongly support the extension or addition of bicycle lanes and their consequent use. However, the lanes are frequently interrupted at crossings and junctions. This emphasizes also the important endangering of bicyclists coming from crossings, junctions and gates, i.e. all situations in which contact of bicyclists to motorized vehicles is possible. Redesigning junctions and bicycle traffic lanes to minimize the possibility of this dangerous contact would be preventive measures. A more consequent helmet use and use and an extension of bicycle paths for a better separation of bicyclists and motorized vehicle would be simple but very effective preventive measures.
In recent years special attention has been paid to reducing the number of fatalities resulting from road traffic accidents. The ambitious target to cut in half the number of road users who are killed each year by 2010 compared with the 2001 figures, as set out in the European White Paper "European Transport Policy for 2010: Time to Decide" implies a general approach covering all kinds of road users. Much has been achieved, e.g. in relation to the safety of car passengers and pedestrians but PTW accidents still represent a significant proportion of fatal road accidents. More than 6,000 motorcyclists die annually on European roads which amounts to 16% of the EU-15 road fatalities. The European Commission therefore launched in 2004 a Sub- Project dealing with motorcycle accidents within an Integrated Project called APROSYS (Advanced PROtection SYStems) forming part of the 6th Framework Programme. In a first step, the combined national statistical data collections of Germany, Italy, the Netherlands and Spain were analysed. Amongst other things parameters like accident location, road conditions, road alignment and injury severity have been explored. The main focus of the analysis was on serious and fatal motorcycle accidents and the results showed similar trends in all four countries. From these results 7 accident scenarios were selected for further investigation via such in-depth databases as the DEKRA database, the GIDAS 2002 database, the COST 327 database and the Dutch element of the MAIDS database. Three tasks, namely the study of PTW collisions with passenger cars, PTW accidents involving road infrastructure features, and motorcyclist protective devices have been assessed and these will concentrate inter alia on accident causes, rider kinematics and injury patterns. A detailed literature review together with the findings of the in-depths database analysis is presented in the paper. Conclusions are drawn and the further stages of the project are highlighted.
Empirical vehicle crashworthiness studies are usually based on national or in-depth traffic accident surveys: Data on accident-involved cars/drivers are analysed in order to quantify the chance of driver injury and to assess certain risk factors like car make and model. As the cars/drivers involved in the same accident form a "cluster", where the size of the cluster equals the number of accident-involved parties, traffic accident survey data are typical multi-level data with accidents as first-level or primary and cars/drivers as secondlevel or secondary units (car occupants in general are to be considered as third level units). Consequently, appropriate statistical multi-level models are to be used for driver injury risk estimation purposes as these models properly account for the cluster structure of traffic accident survey data. In recent years various types of regression models for clustered data have been developed in the statistical sciences. This paper presents multi-level statistical models, which are generally applicable for vehicle crashworthiness assessment in the sense that data on single and multiple car crashes can be analysed simultaneously. As a special case of multi-level modelling driver injury risk estimation based on paired-by-collision car/driver data is considered. It is demonstrated that assessment results may be seriously biased, if the cluster structure inherent in traffic accident survey data is erroneously ignored in the data analysis stage.
Internationally, the need is expressed for harmonized traffic accident data collection (PSN, PENDANT, etc.). Together with this effort of harmonization, traffic accident investigation moves more and more in the direction of accident causation. As current methods only partly address these needs, a new method was set up. The main characteristics of this method are: • Accident/injury causation (associated) factors can objectively be identified and quantified, by comparison with exposure information from a normal population. • All relevant accident and exposure data can be included: human-, vehicle-, and environmental related data for the pre-crash, crash and postcrash situation (the so-called Haddon matrix). The level of detail can be chosen depending on interest and/or budget, which makes the method very flexible. In this paper the accident collection and control group method are presented, including some of the achieved results from a pilot study on 30 truck accidents and 30 control locations. The data were analyzed by using cross-tabulations and classification-tree analysis. The method proved useful for the identification of statistically significant causational aspects.
During the last 5 years, the number of cars fitted with side airbags has dramatically increased. They are now standard equipment, even on many smaller cars or less luxurious vehicles. While some side airbags offer thoracic protection alone, there are those that combine thoracic and head protection (of which most deploy from the seat). Other systems employ separate airbags for head and thorax protection, which are designed to be effective noticeably in a crash against a pole. This paper proposes an evaluation of the effectiveness of side airbags in preventing thoracic injuries to passenger car occupants involved in side crashes. First, the target population (who can take benefit of side airbag deployment and in what circumstances) is defined. Side airbags can be especially effective in cases of impacts on the door with intrusion at a certain impact speed. Then, an example case of a side impact with side airbag deployment is given were side airbag deployment is thought to have had a positive effect on injury outcome. A further case is presented where the impact configuration is likely to have reduced the effect of side airbag deployment on injury outcome. Finally, the estimation of side airbag effectiveness (in terms of additional occupant protection brought exclusively by the airbag) is proposed by comparing injury risk sustained by occupants in (more or less) similar cars (fitted or non fitted with airbags) because, during these years, car structure, and side airbag conception have considerably evolved. In-depth accident data from France, the UK and Germany has been collected. Out of 2,035 side impact accident cases available in the databases, we selected 435 occupants of passenger cars (built from 1998 onwards) involved in an injury accident between year 1998 and year 2004 for EES (Energy Equivalent Speed) values between 20km/h and 50km/h. The occupants, belted or not, were sat on the struck side, whatever the obstacle and type of accidents (intersection, loss of control, etc.). For multiple impact crashes, the side impact is assumed to be the more severe one. Passenger cars were fitted with (96) or without (339) side airbags. Most of the potential risk explanatory variables were correctly and reliably reported in the databases (velocity " impact zone " impact angle " occupant characteristics, etc.). The analysis compared injury risks for different levels of EES and different types of side airbags. A logistic regression model was also computed with injury variables (such as thoracic AIS 2+ or AIS 3+) as the dependant variable and other variables (including airbag type and EES) as explanatory injury risk factors. Results revealed statistically non-significant reductions in thoracic AIS 2+ and AIS 3+ injury risk in side airbag equipped cars in the impact violence range selected (odds ratio between 0.84 and 0.98 depending on types of airbags). The results are discussed. The non-significance is assumed to be due to a low number of cases. Statistical analysis for head injuries was not possible due to the low number of accident cases with passenger cars fitted with head airbags in the databases. Moreover, the discrepancies between the data coming from different countries (especially calculation of EES) might have introduced instability in the analysis.
In Germany, in-depth accident investigations are carried out in the Hannover area since 1973. In 1999 a second region was added with surveys in Dresden and the surrounding area. Internationally, the acronym GIDAS (German In-Depth Accident Study) is commonly used for these surveys. Compared to many other countries, the sample sizes of the GIDAS surveys are much larger. The goal is to collect 1.000 accidents involving personal injuries per year and region. Data collection takes place by using a sampling procedure, which can be interpreted as a two-stage process with time intervals as primary units and accidents as secondary units. An important question is, to what extend these samples are representative for the target population from which they are drawn. Analyses show, for example, that accidents with persons killed or seriously injured are overrepresented in the samples compared to accidents with slightly injured persons. This means, that these data are subject to biases due to uncontrolled variation of sample inclusion probability. Therefore, appropriate weighting and expansion methods have to be applied in order to adjust or correct for these biases. The contribution describes the statistical and methodological principles underlying the GIDAS surveys with respect to sampling procedure, data collection and expansion. In addition, some suggestions regarding potential improvements of study design are made from a methodological point of view.
Annually within the European Union, there are over 50,000 road accident fatalities and 2 million other casualties, of which the majority are either the occupants of cars or other road users in collision with a car. The European Commission now has competency for vehicle-based injury countermeasures through the Whole Vehicle Type Approval system. As a result, the Commission has recognised that casualty reduction strategies must be based on a full understanding of the real-world need under European conditions and that the effectiveness of vehicle countermeasures must be properly evaluated. The PENDANT study commenced in January 2003 in order to explore the possibility of developing a co-ordinated set of targeted, in-depth crash data resources to support European Union vehicle and road safety policy. Three main work activity areas (Work Packages) commenced to provide these resources. This paper describes some of the outcomes of Work Package 2 (WP2, In-depth Crash Investigations and Data Analysis). In WP2, some 1,100 investigations of crashes involving injured car occupants were conducted in eight EU countries to a common protocol based on that developed in the STAIRS programme. This paper describes the purposes, methodology and results of WP2. It is expected that the results will be used as a co-ordinated system to inform European vehicle safety policy in a systematic, integrated manner. Furthermore, the results of the data analyses will be exploited further to provide new directions to develop injury countermeasures and regulations.
Validation of human pedestrian models using laboratory data as well as accident reconstruction
(2007)
Human pedestrian models have been developed and improved continually. This paper shows the latest stage in development and validation of the multibody pedestrian model released with MADYMO. The biofidelity of the multibody pedestrian model has been verified using a range of full pedestrian-vehicle impact tests with a large range in body sizes (16 male, 2 female, standing height 160-192cm, weight 53.5-90kg). The simulation results were objectively correlated to experimental data. Overall, the model predicted the measured response well. In particular the head impact locations were accurately predicted, indicated by global correlation scores over 90%. The correlation score for the bumper forces and accelerations of various body parts was lower (47-64%), which was largely attributed to the limited information available on the vehicle contact characteristics (stiffness, damping, deformation). Also, the effects of the large range in published leg fracture tolerances on the predicted risk to leg fracture by the pedestrian model were evaluated and compared with experimental results. The validated mid-size male model was scaled to a range of body sizes, including children and a female. Typical applications for the pedestrian models are trend studies to evaluate vehicle front ends and accident reconstructions. Results obtained in several studies show that the pedestrian models match pedestrian throw distances and impact locations observed in real accidents. Larger sets of well documented cases can be used to further validate the models especially for specific populations as for instance children. In addition, these cases will be needed to evaluate the injury predictive capability of human models. Ongoing developments include a so-called facet pedestrian model with a more accurate geometry description and a more humanlike spine and neck and a full FE model allowing more detailed injury analysis.
While the number of fatal accidents is diminishing every year, there is still a need of improvement and action to prevent these deaths. Basis for this purpose has to be an analysis about the factors influencing the car crash mortality. There are various studies describing the univariate influence of several factors, but crash scenarios are too complex to be described by a single variable. The multivariate analysis respects the interference of the variables and gets so to more detailed and representative results. This multivariate analysis is based on about 2,600 cases (the data have been collected by the accident research units Hannover and Dresden (during the years 1999-2003). This paper presents a multivariate model (containing ten different variables) which detects 93% of these cases properly. This means it detects the cases as truly survived and truly death.
Institute for Traffic Accident Research and Data Analysis <Tokyo>rnAbstract: Analyses were conducted to clarify the features of rear-end collisions, using an integrated accident database developed by the Institute for Traffic Accident Research and Data Analysis (ITARDA). Focusing on neck injuries in rear-end collisions, analyses were made of the relation to struck-vehicle properties. Regarding the relation to the initial year of registration, the results did not show that newer vehicles tended to have a lower no-neck-injury rate, which was defined in this study as an index. On the contrary, in some passenger car classes, it was observed that the no-neck-injury rate was higher in newer vehicles. The effect of an active head restraint system, which is one type of anti-whiplash device, was analyzed by using not only the no-neck-injury rate but also a regression analysis. The results showed that the effect of an active head restraint system on suppressing the incidence of neck injuries was statistically significant.rn
76 severe traffic accidents had been investigated in depth in an ongoing Volkswagen-Tongji University joint accident research project in JiaDing district, Shanghai, PR China since June 2005. With a methodology similar to German accident research units in Dresden and Hannover, a research team proceeds to the scene immediately after the incident to investigate and collect various data on environment, accident occurrence, vehicle state and deformations as well as injuries. The data combined with the results of accident reconstruction will be stored in a database for further statistical and casuistic analysis. The first outcome of the project supports the hypothesis that a main causation for the large number of traffic accidents in China is the lacking of risk awareness in Chinese driver behaviour. Low seat-belt use and the high proportion of vulnerable and poorly protected two-wheelers in traffic are reasons for the high injury and fatality rate in China. The research work shows that accident research in China is feasible and able to give support to tackle one of the urging problems in Chinese development.
The "Seven Steps Method" is an analysis and classification system, which describes the human participation factors and their causes in the temporal sequence (from the perceptibility to concrete action errors) taking into consideration the logical sequence of individual basic functions. By means of the "seven steps" it is possible to describe the relevant human causes of accidents from persons involved in the accident in an economic way with a sufficient degree of exactitude, because the causes can be further differentiated in their value (e.g. diversion as external diversion with regard to impact due to surroundings) and their sub values (e.g. external diversion with regard to impact due to surroundings in the shape of a "capture" of the perception by a prominent object of the traffic environment). Theoretically it is possible that one or more causing moments can be assigned to a person involved in an accident in each of the "seven steps"; however it is also possible to sufficiently clarify the cause in only one level (examples for this are described). In the practice of accident investigation at the site of the accident, the sequence chart is also relevant. With its assistance the questioning of the people involved in an accident can be accomplished in a structured way by assigning a set of questions to each step.
The European Union has set a target to reduce all road fatalities (over 40,000) with 50% in 2010. This target percentage remained unchanged with the introduction of the ten new member states within the EU as by May 1st, 2004. According to Eurostat, 34% of all fatalities in 1998 in the, then, fifteen states of the European Union were the result of single vehicle collisions. This represents over 14,000 lives lost each year of which many can likely be saved through better roadside infrastructure design. The challenge for road safety professionals is to find methods and design strategies that help to reduce these casualties. Procedures for full-scale vehicle crash testing of guard rails were first published in the US in 1962. Present European regulation is mainly based on these procedures and later developments. Since then the vehicle fleet has changed considerably. Due to the complexity of the actual safety problem the numerical simulation approach offers a good opportunity to evaluate the different parameters involved in road safety, such as infrastructure properties, vehicle type, vehicle occupants and injuries. The ideal situation would be that simulation tools are coupled or integrated and all involved effects would be related. At the moment this is not the case yet, but initiatives are taken and a new virtual era has started. This paper offers a method looking at two components that encompass the driving environment: the car and the guardrail. As part of the EC-funded project, RISER (Roadside Infrastructure for Safer European Roads) a multi body simulation program study is carried out to determine sensitivities of some parameters in car to guardrail collisions and gives insides in performance of the car with passive safety equipment, the guardrail and the interaction of these objects with each other. By offering a set of methods that includes these two aspects and their intertwining relations, more confidence can be gained in actually reducing fatalities due to single vehicle collisions with, or due to, roadside furniture. Reducing the number of fatalities of single vehicle crashes would contribute greatly to the stated goal of reducing casualties altogether.
Since the compulsory use of child restraints for children up to 5 years of age was introduced in 2000, restraint use among younger children has increased significantly. However, the observed rate of child restraint use plateaus at around 50%, and apparently little spillover effect has been found for older children who are not covered by the law. This report examines the restraint use patterns for children who were injured in cars in relation to driver and child passenger characteristics. Univariate and multivariate analyses were conducted to describe the association between the outcome measure (the proper use of restraints for children) and relevant variables. Better ways for parents and caregivers to improve the use of restraints for children are also discussed.
The incidence and treatment of sternal fractures among traffic accidents are of increasing importance to ensure best possible outcomes. Analysis of technical indicators of the collision, preclinical and clinical data of patients with sterna fractures from 1985-2004 among 42,055 injured patients were assessed by an Accident Research Unit. Two time groups were categorized: 1985-1994 (A) vs. 1995-2004 (B). 267/42,055 patients (0.64%) suffered a sterna fracture. Regarding the vehicle type, the majority occurred after car accidents in 0.81% (251/31,183 pts), followed by 0.19% (5/2,633pts) driving motorbike, and 0.11% (4/3,258pts) driving a truck. 91% wore a safety belt. Only 13% of all passengers suffering a sternal fracture had an airbag on board (33/255 car/trucks), with an airbag malfunction in 18%. The steering column was deformed in 39%, the steering wheel in 36%. Cars in the recent years were significantly older (7.67-±5 years (B) vs. 5.88-±5 years (A), p=0.003). Cervical spine injuries are frequent (23% vs. 22%), followed by multiple rib fractures (14% vs. 12%) and lung injuries (12% vs. 11%). We found 9/146 (6%) and 3/121 patients (3%) with heart contusion among the 267 sternal fractures. MAIS was 2.56-±1.3 vs. 2.62-±1.3 (A vs. B, p=0.349). 18% of patients were polytraumatized, with 11.2% dying at the scene, 2.3% in the hospital. Sternal fractures occur most often in old cars to seat-belted drivers often without any airbag. Severe multiple rib fractures and lung contusion are concomitant injuries in more than 10% each indicating the severity of the crash. Over a twentyyear period, the injury severity encountered was not different with 18% polytrauma patients suffering sternal fractures.
Due to recent years accident avoidance and crashworthiness on Austrian roads were mostly developed on national statistics and on-scene investigation respectively. Identification and elimination of black spots were main targets. In fact many fatal accidents do not occur on such black spots and black-spot investigation has reached a limit. New methods are required and therefore the Austrian Road Safety Programme was introduced by the Austrian Ministry of Transport, Innovation and Technology. The primary objective is the reduction of fatalities and severe injuries. Graz University of Technology initiated the project ZEDATU (Zentrale Datenbank tödlicher Unfälle) with the goal to identify similarities in different accident configurations. A matrix was established which categorizes risk and key factors of participating parties. Based on this information countermeasures were worked out.
NASS: the glass is half full
(2007)
The National Accident Sampling System (NASS) was born in the late 1970s. It was based on a substantial amount of experience and analysis of what was needed in the United States to understand the safety challenges of our highways. This work also showed how to collect high quality and useful crash data efficiently. Unfortunately, when Ronald Reagan - a President who believed in limited government - was elected, any hope of full funding for NASS was lost. The concept of 75 teams investigating about 18,000 serious crashes in detail annually was never realized. The system got up to 50 teams, then was cut to 36, and finally to 24 teams investigating fewer than a quarter of the originally anticipated number of crashes per year. Despite this, the NASS investigations provide a rich source of data, collected according to a sophisticated statistical sampling system to facilitate detailed national estimates of road casualties on our nation- highways and their causes. In addition, changes have been made in recent years to increase the number of more serious crashes of recent model vehicles to make the results more relevant to improving vehicle safety. A recent, detailed examination of hundreds of rollovers has provided considerable insight into rollover casualties and into what can be done to reduce them. Some of these results will be presented that show the value of the NASS system. Our experience with NASS and the Fatal Accident Reporting System (FARS) suggests a number of improvements that could be made in the United States" crash data systems. It also provides justification for a doubling or tripling of our national expenditures on crash data collection.
The increase in light duty trucks (LDT) on the road in the US is a safety concern because of their aggressivity, or risk they present to occupants of cars, especially in side impacts. We use FARS data to look at fatality trends in frontal and side impacts between cars and LDT. FARS data is also used to determine risk, or fatalities per registered vehicle, imposed on car drivers from other vehicle types. We use NASS CDS data to investigate sources of serious injuries in vehicles with side impact. These sources of injury are categorized into three major groups: 1) contact without intrusion, 2) contact with intrusion, and 3) restraints. We find a greater fraction of intrusion related injuries in cars struck on their side by SUV or pick-up trucks than when they are struck by other cars.
This study examines the severity and types of injuries sustained by child pedestrians aged 18 years and below in order to identify the body regions at greatest risk for injury in a pedestrian accident. Detailed medical diagnoses were reviewed retrospectively for 572 child pedestrians admitted to an urban pediatric trauma center with injuries during the time period from January 2001 to December 2005. Eighty percent of these children sustained AIS 2 or greater injuries, most commonly to the lower extremity (41%) and head (34%). Fortyfour percent of admitted children had more significant AIS 3 or greater injuries primarily to the head (58%), thorax (17%) and lower extremities (14%). Testing procedures to assess the child- interaction with the motor vehicle should include injury assessment for the pediatric head, thorax and lower extremities. This understanding of how child pedestrians interact with motor vehicles may provide insight into effective countermeasures with potential for implementation in vehicle designs world-wide.
The number of injuries sustained by car occupants involving the head, thorax, spine, pelvis and the upper limbs have been reduced significantly during recent years. This is probably due to better safety features in the cars, especially the availability and usage of safety belts, airbags etc. Therefore one can notice clinically a relative increase in survivors of severe frontal crashes, but many of them have injuries to the lower extremities. To verify this, we analyzed the foot and ankle injuries of front seat passengers.
In Finland all fatal motor vehicle accidents are studied in-depth on-the-spot by multidisciplinary (police, road and vehicle engineers, physician and behavioural scientist) road accident investigation teams (legislation 2001, work started 1968), which operate in every province. The purpose of the teams is to uncover risk factors that turned an ordinary driving situation into a serious accident and give safety recommendations for improving road safety. The investigation teams do not take a stand on guilt or insurance compensation. When analysing accidents the teams use the concepts of key event, immediate, background and injury risk factors. Compiled investigation folders of each case contain investigation forms from each member, preinvestigation protocol, photographs, sketches etc. About 500 items of information are collected from each accident party. The collected information is also coded into a computer database. Both the database and the investigation folders are widely utilized by researchers and authorities conducting safety work.
This study aimed to identify the occurrence, type and mechanisms of the traumatic injuries of the vulnerable road users in vehicle collisions, and to determine the effects of human, engineering, and environment factors on traffic accidents and injuries. The pedestrian accident cases were collected in the years 2000 to 2005 from Changsha Wujing hospital China and Accident Research Unit at Medical University Hannover in Germany. A statistic analysis was carried out using the collected accident data. The results from analysis of Changsha data were compared with results from analysis of GIDAS data Hannover. The injury severities were determined using AIS code and ISS values. The results were presented in terms of cause of injuries, injury distributions, injury patterns, injury severity. The factors influenced the injury outcomes were proposed and discussed for the vehicle transport environment and road users. The results were discussed with regard to accident data collection, accident sampling and injury distributions etc. In the urban area of Changsha, motorcycles and passenger cars are most frequently involved in vehicle pedestrian accidents. Head and lower extremities injuries are the predominant types of pedestrian injuries. The pedestrian accidents were identified as vital issue in urban traffic safety and therefore a high priority should be given to this road user group in research of safe urban transportation. In Hannover area, cars are most frequently involved in traffic accidents, injured pedestrians are involved in road traffic of Germany in 13% of all causalities only in 2005 and have nearly the same number as motorcyclists, but the half of bicyclists.
The objective of this study was to identify aspects of the individual experience and behaviour of drivers in intersection accidents. A total of 40 accident drivers sketched their ideas and expectations relating to intersection assistance using the method of Structure Formation Technique. Using this method prepared content cards and relation cards for a subject matter are formed together in a structure through the application of an explicit set of rules. The structures generated in this process were compared with the structures of 20 control persons who have not recently experienced an accident at intersections. The basis for this comparison was a case-control design with matched samples regarding the variables age, sex, education, occupation, driving experience and annual mileage. The results of the accident reports indicate that additional assistance is instrumental in the perception of other road users. Generally the interviewed drivers were open-minded towards the use of intersection assistance systems. Drivers who have recently experienced an accident at intersections significantly more often approved of warning assistance in their vehicle than drivers who have not recently experienced an accident. Further accident experienced drivers favoured warning and information via audio warning more frequently. The ideas of the drivers were strongly shaped by the experiences with already available advanced driver assistance systems. Hence acoustic and visual warnings were generally preferred to tactile warnings. The findings also indicate a relationship between the variable age and the acceptance of automatic vehicle intervention, and the suggestion of a head up display as a configuration of a visual warning system.
This study updates previous IIHS studies comparing estimated delta Vs for crash tested vehicles to the distribution of estimated delta Vs in the National Automotive Sampling System (NASS) Crashworthiness Data System (CDS). The delta V estimates for 232 frontal crash tests at 64.4km/h into a deformable barrier with 40 percent overlap are compared with estimates from frontal offset crashes in the 1997-2004 NASS database. All delta V estimates were based on SMASH, the delta V estimating program used by NASS since 1997. Results indicated that for all vehicles tested by IIHS, SMASH delta Vs were, on average, 32 percent lower than impact speeds and about 28 percent lower than the expected delta V. Almost 80 percent of all real-world frontal crashes resulting in AIS 3+ injuries and just over 60 percent of all fatal crashes occur at or below the average estimated delta V calculated for crash tested vehicles.
In the context of this study, different data sources for accident research were examined regarding their possible data access and evaluated concerning the individual quality and extent of the data. Analyses of accidents require detailed and comprehensive information in particular concerning vehicle damages, injury patterns and descriptions of the accident sequence. The police documentation supplies the basic accident statistics and is amended in the context of the forensic treatment by further information, e.g. by medical and technical appraisals and witness questionings. As a new approach to the data acquisition for the analysis of fatal traffic accidents, the information was made usable which was collected by the police and by the investigations of the public prosecutor. The best strategy for obtaining reliable, extensive and complete data consists of combining the information from these two sources: the very complete, but elementary statistic data of the Niedersächsisches Landesamt für Statistik (Lower Saxony State Authority of Statistics), based on the police documentation as well as the very extensive accident information resulting from the investigation documentation of the public prosecutor after conclusion of the procedure, the so-called Court Records. Of all 715 fatal traffic accidents, which happened in the year 2003 in the German State of Lower Saxony, 238 cases were selected by means of a statistically coincidental selective procedure based on a statistically representative manner (every third accident). These cases cover the investigation documents of the 11 responsible public prosecutor- offices, which were requested and evaluated while preserving the data security. Of the 238 cases 202 cases were available, which were individually coded and stored in a data base using 160 variables. Thus a data base of a sample of representative data for fatal accidents in Lower Saxony was set up. The data base contains extensive information concerning general accident data (35 variables), concerning road and road surface data (30 variables), concerning vehicle-specific data (68 variables) as well as concerning personal and injury data (27 variables).
The primary goal of this investigation was to determine the relative risk of traffic accidents in students. In a two year period, a survey amongst 2,325 students was carried out, and 3,645 injuries sustained by students treated at our hospital were analyzed. Moped-riding in adolescents were associated with a 23.75-fold increased risk for injury as compared to biking. Children who ride bicycles have a 2.2-fold increased risk for an injury sustained by traffic accidents compared to pedestrians. None of 50 injured bicycle riders with helmet had an AIS for head injuries of more than 2. 24 of 233 injured bicycle drivers without helmet had an AIS for head injuries of more than 2. The use of a protective helmet significantly reduced the severity of head injuries. The level of awareness towards danger and a history of previous accidents correlate with the likelihood of future accidents. Due to the severity of traffic accidents, more adequate prevention measures (wearing of bicycle helmets and better education for moped riders) are urgently needed.
The price of a new car increased almost every year for a long period. In recent years however, the budget available to most people for purchasing a car either did not grow or became even smaller. Therefore it was in the interest of some OEMs to offer economical car models in the so-called "8,000- Euro class". Here an important question arose regarding the safety of these vehicles. There is no question that the very high safety level of cars reached in Europe during the last decades should not be sacrificed as a consequence of smaller budgets. Customers with sense of responsibility have the right to be properly informed about the balance between safety and price so that they can make a deliberate decision when buying either a new or a used car. Against this background, the German magazine "AutoBILD" commissioned DEKRA to conduct fullscale frontal crash tests with a view to publishing the results. These tests have been carried out in accordance with the corresponding Euro NCAP crash test requirements and performance criteria. The tested vehicles were two new Logans produced by the manufacturer Dacia, two used cars of the type VW Golf IV (registration date 2000) and one new VW Fox. This paper describes the safety features of the vehicles and the results of the five crash tests to demonstrate state-of-the-art safety levels and what levels may be expected from vehicles in the "8,000- Euro class". Looking at real-world crashes it is of interest to think about future trends in a more detailed manner. Therefore it will be more and more necessary to supplement the federal statistics with more detailed in-depth information about the consequences of accidents and the safety performance of crashed vehicles.
In recent years the boundaries between active and passive safety blurred more and more. Passive safety in the traditional term includes all safety aspects to prevent occupants to be injured or at least injury severity should be reduced. Passive Safety starts with the collision (first vehicle contact) and ends with rescue (open vehicle doors). Within this phase the occupant has to be protected by the passenger compartment whereby no intrusion should occur. Active safety on the other side was developed to interact prior to the collision whereby the goal is to prevent accidents. The extensive interaction between active and passive safety led to the terminologies "Primary" and "Secondary" safety whereas the expression Integrated Safety Concept was generated. Within this study the most well documented single vehicle accidents with cars not equipped with ESP were identified from the PENDANT database and reconstructed. Additional cases were found in the database ZEDATU of TU Graz. In comparison each case was simulated with the assumption that the cars were equipped with ESP. The differences regarding accident avoidance or crash severity as well as reduction of injury risk were analysed.
This paper uses the national accident statistics of Great Britain to evaluate the effectiveness of Electronic Stability Control Systems (ESC) to reduce crash involvement rates. The crash experience of 8,951 cars is analysed and compared to a closely matching set of non-ESC cars using case-control methods. This is one of the largest ESC samples analysed to date. Overall the cars with ESC are involved in 3% fewer crashes although the effectiveness is substantially higher under conditions of adverse road friction. ESC equipped cars are involved in 15% fewer fatal crashes although this reduction represents the combined effect of ESC and passive safety improvements.
There is a need for detecting characteristics of pedestrian movement before car-pedestrian collisions to trigger a fully reversible pedestrian protection system. For this purpose, a pedestrian sensor system has been developed. In order to evaluate the effectiveness of the sensor system, the in-depth knowledge of car-pedestrian impact scenarios is needed. This study aims at the evaluation of the sensor system. The accident data are selected from the STRADA database. The accident scenarios available in this database were evaluated and the knowledge of the most common scenarios was developed in terms of the pedestrian trajectory, the pedestrian speed, the car trajectory, the car velocity, etc. A mathematical model was then established to evaluate the sensor system with different detective angles. It was found that in order to detect all the pedestrians in the most common scenarios on time the sensor detective angle must be kept larger than 60 degrees.
Since 2005 the German In-Depth Accident Study (GIDAS) also records aspects of active vehicle safety. This is done because vehicles are fitted with an increasing number of active safety devices which have undoubtedly an influence on the number, severity and course of accidents. Accident researchers expect that collecting active safety data will facilitate to assess and quantify the impact of these and future devices. It is the aim of this paper to outline benefits and limitations associated with the recording of active safety aspects within indepth studies. An overview about possible areas where active safety data can be useful will be given. For that purpose single safety or comfort systems will be selected to estimate the effects of an accident database which includes variables associated with these systems. Questions with regard to the limitations of collecting active safety data will be addressed. Possible items are for example the usability of the data recorded, the real accident cause, the small number of relevant accidents, the time span needed to gather a sufficient dataset, the small share of vehicles equipped with a certain system or different functionalities of systems that are supposed to fall in the same category. As a result user needs for a reasonable data collection of active safety elements will be elaborated.
The accident research project in Dresden was founded in July 1999. To date over 6.000 crash investigations have been undertaken. About 10.000 vehicles have been documented and over 13.000 participants have been debriefed. But there is much more than this scientific success. Because of the interdisciplinary character between the medical and technical focus, the project affords an important contribution for the education of the involved students. Over 200 students of different fields of study have got experiences not only for the occupational career. This lecture describes the additional effects of the accident research project regarding the education of the students, the capacity for teamwork and learning about dealing with accident casualties.
Description of road traffic related knee injuries in published investigations is very heterogeneous. The purpose of this study was to estimate the risk of knee injuries in real world car impacts in Germany focusing vulnerable road users (pedestrians, bicyclists and motorcyclists) and restrained car drivers. The accident research unit analyses technical and medical data collected shortly after the accident at scene. Two different periods (years 1985-1993 and 1995-2003) were compared focusing on knee injuries (Abbreviated Injury Scale (AISKnee) 2/3). In order to determine the influences type of collision, direction and speed as well as the injury pattern and different injury scores (AIS, MAIS, ISS) were examined. 1.794 pedestrians, 742 motorcyclists, 2.728 bicyclists and 1.116 car drivers were extracted. 2% had serious ligamentous or bony injuries in relation to all injured. The risk of injury is higher for twowheelers than for pedestrians, but knee injury severity is higher for the latter group. Overall the current knee injury risk is low and significant reduced comparing both time periods (27%, p<0,0001). Severe injuries (AISKnee 2/3) were below 1%). Improved aerodynamic design of car fronts reduced the risk for severe knee injuries significantly (p=0,0015). Highest risk of injury is for motorcycle followed by pedestrians, respectively. Knee protectors could prevent injuries by reducing local forces. The classically described dashboard injury was rarely identified. The overall injury risk for knee injuries in road traffic is lower than estimated and reduced comparing both periods. The aerodynamic shape of current cars compared to older types reduced the incidence and severity of knee injuries. Further modification and optimization of the interior and exterior design could be a proper measurement. Classic described injury mechanisms were rarely identified. It seems that the AIS is still underestimating extremity injuries and their long term results.
Vorbemerkungen: Schwingungsanfällige Zugglieder im Sinnen dieser Regelungen sind Hänger und Schrägkabel als Seile oder Vollprofile von Schrägseilbrücken, Hängebrücken und Bogenbrücken. Nachfolgend werden Bemessungsregeln für Hänger von Bogenbrücken angegeben. Stählerne Hänger von Bogenbrücken sind schlanke Zugglieder zwischen der Fahrbahnplatte einer Brücke (bzw. dem Versteifungsträger) und dem darüber gespannten Bogen. Die Verbindung zwischen Hänger und Bogen bzw. Versteifungsträger erfolgt meistens über angeschweißte Anschlussbleche. Ermüdungswirksame Doppelspannungsamplituden, die je nach Häufigkeit und Intensität zu Rissbildung führen können, entstehen bei runden Hängern insbesondere durch wechselnde Verkehrsbelastung und wirbelerregte Querschwingungen, sowie in Einzelfällen auch durch Regen-Wind-induzierte Schwingungen. Rechteckige Hängerquerschnitte können durch Verkehrsbelastung und wirbelerregte Querschwingungen ermüdungsrelevant beansprucht bzw. durch Galloping zu instabilen Schwingungen angeregt werden. Die nachfolgenden Regelungen und Empfehlungen für eine dauerhafte Konstruktion und einen ermüdungssicheren Hängeranschluss wurden für Rundstahl- und Flachstahlhänger hergeleitet und sind folglich auf diese zu beziehen. Eine Übertragung auf andere Querschnittsformen kann zwar erfolgen, allerdings sind hierzu weitergehende Überlegungen bezüglich anzusetzender Kraftbeiwerte, Wirklängen und nachzuweisenden Frequenzbereichen notwendig.
The German Federal Ministry of Economics and Technology is funding a projectrncalled "Leistra2" with the aim of understanding the tire road contact and to find measures to reduce traffic noise, in particular to reduce the noise of tires rolling on pavements, i.e. tire-road noise. The project is composed out of three mayor subjects, low noise tires, low noise pavements and verification of the results, each made out of single sub-projects. The purpose of this paper is to give a survey about Leistra2 and to report about the latest activities and results. More detailed information and contact data of the partners involved can be found at http://www. LeiStra2.de. The program is the successor of the program LeiStra (Leiser Strassenverkehr), dealing with similar topics.rn
Die vorliegende Studie befasst sich mit der Untersuchung der aktiven Sicherheit von Motorradschutzhelmen. Es wurden auf einander abgestimmte Messungen in den Untersuchungsfeldern Aeroakustik, Aerodynamik, Temperaturverhalten (Belüftungssystem) und psychophysiologische Leistungs- und Befindlichkeitsparameter (Elektrokardiogramm, Elektromyogramm, elektrodermale Aktivität) sowohl in einem Windkanal und als auch in Form systematischer Fahrversuche (Messfahrten) durchgeführt. Grundsätzlich wurden die Messungen in den drei Geschwindigkeitsbereichen 80, 120 und 160 km/h mit einem unverkleideten Motorrad der Mittelklasse (650 ccm, ABS) absolviert. Untersuchungsgegenstand waren hierbei 12 unterschiedliche, entsprechend ausgewählte, aktuelle ECE-R 22.05 geprüfte Helme. Während auftretende Halskräfte mit einem Kraftmessroboter (dreiachsig) erfasst wurden, diente eine Messpuppe mit Head Acoustic Kunstkopf zur Aufzeichnung von Schalldruckpegeln Eine identische Akustikmesskette konnte in Verbindung mit In-Ear Mikrofonen bei den Messfahrten eingesetzt werden. Die psychophysiologischen Parameter wurden mittels einer mobilen, achtkanaligen Messkette und entsprechend adaptierten Modulen erfasst. Mit der gleichen Messkette wurden die Temperaturverläufe mittels sieben Temperatursensoren (davon ein Referenzwertgeber) zwischen Kopfoberfläche und Helminneren registriert. Der Helmaufbau wurde computertomographisch und zerlegend untersucht. Auf der Grundlage der Ergebnisse können folgende Empfehlungen bezüglich der aktiven Helmsicherheit gemacht werden: - Aeroakustik: Die Messungen lassen Gehör schädigende Schalldruckpegel (Maximalwerte 110 dB(A)) erkennen. - Aerodynamik: Bei einer Geschwindigkeit von 160 km/h wurden Werte für die Auftriebskraft (z-Richtung) zwischen 13 und 28 N ermittelt; für die Widerstandskraft (x-Richtung) solche zwischen 29 und 40 N. Ein akuter Bedarf an Anforderungsformulierungen wurde nicht erkennbar. Temperatur und Belüftungssystem: Maximaltemperaturen waren nicht höher als 36-°C. Nur bei fünf Helmen war unmittelbar nach öffnen der Belüftung ein Kühleffekt messbar. Anhand identifizierter Funktionsdefizite und Gestaltungsfehler von Belüftungssystemen konnten Verbesserungshinweise abgeleitet werden.
Der vorliegende Abschlussbericht des von der Bundesanstalt für Straßenwesen (BASt) initiierten Projekts behandelt Fragestellungen, die sich auf verschiedene Gebrauchsarten ausgewählter Fahrerassistenzsysteme (FAS) - vom "korrekten Gebrauch" bis hin zum "Fehlgebrauch" - beziehen. Das unmittelbare Gebrauchsverhalten dreier zukünftiger Systeme FCW (Frontal Collision Warning), BSW (Blind Spot Warning) und CSA (Curve Speed Assistant) wurde experimentell im Fahrsimulationslabor untersucht. Der Gebrauch zweier am Markt verfügbarer Systeme, ACC (Adaptive Cruise Control) und Spurassistent, wurde anhand subjektiver Daten per Fragebogen- beziehungsweise Interviewmethode erhoben. Die ausgewählten drei zukünftigen FAS konnten von Versuchspersonen als virtuelle Prototypen im Fahrsimulator genutzt werden. Neben den individuellen Verhaltensänderungen bei der Fahrt mit einem FAS wurde außerdem der Einfluss verschiedener Systembeschreibungen auf das Gebrauchsverhalten untersucht. Die Auswertung der Fahrdaten zeigt für das System FCW vereinzelte statistisch signifikante Veränderungen in Richtung eines risikoreicheren Fahrerverhaltens. Die verschiedenen Systembeschreibungen führten bei keinem der drei FAS zu nachweisbaren Verhaltensauswirkungen. Die Befragung von Nutzern eines Spurassistenten deckte in Einzelfällen ein kritisches Systemverständnis auf (zum Beispiel Einsatz bei Müdigkeit). In Interviews mit Nutzern eines ACC Systems wurde vereinzelt über eventuell kritische Einsatzsituationen berichtet (zum Beispiel Nutzung bei eingeschränkten Sichtverhältnissen). Der allgemeine Gebrauch der untersuchten Fahrerassistenzsysteme wird dennoch als nicht sicherheitskritisch bewertet. Sowohl bei der Diskussion der einzelnen Ergebnisse als auch in den abschließenden Kapiteln des Berichts wird kritisch auf Vor- und Nachteile verschiedener Untersuchungsinstrumente eingegangen. Der Bericht endet mit der Vorstellung eines allgemeinen Modells zur Entstehung und Einordnung verschiedener Gebrauchsarten technischer Systeme.
Es ist zu beobachten, dass trotz einer Abnahme der Zahl der Verletzungen und der Verletzungsschwere der Insassen bei Pkw-Unfällen Halswirbelsäulen (HWS)-Distorsionen, speziell im unteren Geschwindigkeitsbereich häufiger auftreten. Neben anderen Faktoren werden auch veränderte Beschleunigungs- und Verzögerungsimpulse, die im Crashfall auf die Insassen wirken, als möglicherweise ursächlich für die Entstehung von HWS-Distorsionen angesehen. In der vorliegenden Arbeit wird untersucht, welchen Einfluss konstruktive Veränderungen, die durch Versicherungseinstufungstests bedingt werden, auf die Beschleunigungs- und Verzögerungsimpulse im Fahrzeuginnenraum haben. Versuche zum Fußgängerschutz wurden einvernehmlich nicht durchgeführt, da die Fahrzeuge noch nicht konsequent nach Fußgängerschutzkriterien konzipiert werden. Die Untersuchungsmethode lässt sich gliedern in: - Analyse von internationalen Versicherungssystemen und Analyse der aus den Versicherungseinstufungstests resultierenden Veränderungen von Fahrzeugstrukturen; - Durchführung und Analyse von eigenen Aufprallversuchen mit Fahrzeugteilstrukturen und vergleichende Analyse von Vollfahrzeugversuchen der Versicherungswirtschaft; Zusammenführen der getätigten Schritte. Bei der Ersteinstufung eines Pkw in die Vollversicherung dient der Versicherungseinstufungstest des RCAR/AZT (Prüfgeschwindigkeit 15 km/h) zur Bestimmung der Schadenshöhe und damit zur Einstufung in eine Typklasse. In vielen weiteren Staaten dienen dieser oder ähnliche Tests zur Bewertung der Reparaturfreundlichkeit von Pkw. Um bei einem Versicherungseinstufungstest den Schaden möglichst gering zu halten, haben nahezu alle Neufahrzeuge Querträgersysteme mit kostenarm wechselbaren Absorptionselementen, die die Crashenergie gezielt auf kurzem Weg aufnehmen. Durch die neu EG-Richtlinie 2003/102/EG zum Fußgängerschutz müssen zukünftig hinter der Stoßfängeraußenhaut und vor dem massiven Querträger weiche Schäume untergebracht werden. Der Bauraum für Querträger und Energieabsorptionselemente wird dadurch weiter eingeschränkt. Diese Anforderungen veranlassen die Hersteller dazu, die Energieabsorptionselemente steifer zu gestalten, um einen effektiven Energieabbau bei kurzen Stopplängen zu gewährleisten. Durch diese Maßnahmen wird zwar der Insassenschutz bei Frontalaufprallen im Hochgeschwindigkeitsbereich verbessert, es werden aber zugleich höhere Innenraumverzögerungen (schnellerer Anstieg, höhere mittlere Verzögerung) bei Crashs im gesamten Geschwindigkeitsbereich erzeugt. Eine durchgeführte Korrelation zwischen konstruktiven Veränderungen am Fahrzeug und empirisch bestimmten Verzögerungsverläufen zeigte, dass eine günstigere Einstufung in der Fahrzeugvollversicherung nicht zwangsläufig höhere Verzögerungsimpulse für den Innenraum bedingen muss. Bei der Analyse von 172 Crashversuchen des Allianz Zentrums für Technik mit Neufahrzeugen aus den Jahren 1992 bis 2003 zeichnen sich aber statistisch bedeutsame ßnderungen in den Verzögerungsverläufen über die Prüfjahre ab: - Anstieg der Verzögerung wird steiler; - Mittelwert der Verzögerung wird grösser; - Zeitdauer bis zum Auftreten der maximalen Verzögerung wird kürzer; - dynamische Gesamtdeformation wird kleiner. Die steife Auslegung der für den Versicherungseinstufungstest relevanten Crashteile verbessert den Insassenschutz bei Hochgeschwindigkeitscrashs. Wenn es sich aber durch weitere Untersuchungen bestätigt, dass höhere Verzögerungs- beziehungsweise Beschleunigungsimpulse die Auftretenswahrscheinlichkeit von HWS-Verletzungen im Niedriggeschwindigkeitsbereich vergrößern, so sollten gezielt Maßnahmen zur Verringerung dieser Verletzungsrisiken ergriffen werden. Dazu gehören die weitere Optimierung der Sitzstrukturen einschließlich der Kopfstützen und die Entwicklung adaptiver Crashstrukturen, die dem Crashfall angepasste Kraft-Weg-Kennlinien ermöglichen.
Das New Car Assessment Program, kurz "NCAP", befasst sich mit der Bewertung von Neufahrzeugen. Dabei gehen die Bewertungskriterien über die vom Gesetzgeber geforderten Mindestvoraussetzungen hinaus und sollen dem Verbraucher als Hinweise für die Kaufentscheidung beim Neuwagenkauf dienen und die Sicherheit in der gesamten Fahrzeugflotte erhöhen. Im Auftrag der Bundesanstalt für Straßenwesen wurden deshalb unterscheidbare Beleuchtungsmerkmale, welche direkt die Sicherheit des Fahrzeuglenkers berühren, erarbeitet und daraus ein Bewertungssystem für die Beleuchtung am Fahrzeug entwickelt. Die gesetzlichen Bestimmungen erlauben es dem Hersteller von lichttechnischen Einrichtungen, sich innerhalb einer gewissen Bandbreite zu bewegen, die ein unterschiedliches Design und Erscheinungsbild der Kraftfahrzeuge ermöglicht. Heutige Systeme gehen meist deutlich über diese Mindeststandards hinaus. Gerade diese Situation rechtfertigt es, Bewertungskriterien zu erarbeiten, welche sich zum Beispiel mehr an der Erkennbarkeit von Hindernissen und der Blendung anderer Verkehrsteilnehmer, also an zusätzlicher Sicherheit, orientieren. Bei der Bewertung von Fahrzeugen werden zwei grundsätzliche Aspekte unterschieden, die aktive und die passive Sicherheit. Jeder dieser beiden Aspekte kann wiederum in verschiedene Teile aufgespaltet werden. Die Fahrzeugbeleuchtung ist ein Teilaspekt der aktiven Sicherheit. Im Rahmen dieses Projektes ist die Beleuchtung in folgende vier in der Bewertung unterschiedlich gewichtete Teilbereiche unterteil worden, die wiederum in weitere Unterkategorien untergliedert wurden: 1) Leistung: (Maximal 40% der Gesamtpunktzahl); Bewertet die Straßen- und Umfeldbeleuchtung, dient dem Sehen. 2) Sicherheit: (Maximal 40% der Gesamtpunktzahl); Bewertet die Sichtbarkeit und Signalqualität, dient dem Sehen und Gesehenwerden. 3) Verträglichkeit: (Maximal 10% der Gesamtpunktzahl); Bewertet soziale, ökonomische und ökologische Aspekte. 4) Komfort: (Maximal 10% der Gesamtpunktzahl); Bewertet Komponenten, die den Fahrer von Nebenaufgaben entlasten und die Konditionssicherheit betreffen. Zusammenfassung: Es wurde ein Bewertungssystem für die Beleuchtung des Kraftfahrzeugs erarbeitet und zur Verfügung gestellt. Die einzelnen Bewertungskriterien wurden auf der Basis wissenschaftlicher Erkenntnisse entwickelt und gehen über die gesetzlich vorgeschriebenen Mindestwerte hinaus. Somit ergibt sich unter anderem für ein NCAP die Möglichkeit, verschiedene Beleuchtungskonzepte von Fahrzeugen zu vergleichen.
The second ESAR Conference took place at the Medical University Hannover. This year conference presents the current state of affairs of relevant research activities in the field of in-depth investigations. The first conference on ESAR (Expert Symposium on Accident Research) was established in 2004. It is planned to hold ESAR every two years. Hannover seems to be the right place for this conference concerning the fact that the first in-depth research team was found here in the year 1973 and comprehensive studies on accident analysis were spread out from here around the world continuously. This year conference topped all expectations in terms of the numbers of participants, in the variety of papers and the interdisciplinary of presenters from medical, psychological and engineering background. More than 100 delegates from all over the world, that means 13 different countries and from 4 different continents, came to Hannover, presented their results of accident investigation and discussed countermeasures for accident prevention and injury reduction. ESAR should be a platform for exchange of knowledge to find an optimized way for increase of traffic and vehicle safety by in-depth investigation and methodology. ESAR as international conference should be a platform for consideration of all nations round the world. This seems to be very important for the current situation, having high safety in the high industrial countries of Europe, US and Australia, but low safety and high injury risk in Asia and Africa.
Ziel des vorliegenden Forschungsprojekts war die Quantifizierung von staubedingten Reisezeitverlusten im Jahr 2000, die auf infrastrukturbedingte Kapazitätsengpässe einschließlich Verkehrsunfällen und Pannen zurückzuführen sind. Zusammen mit den Ergebnissen der "Quantifizierung staubedingter Reisezeitverluste auf Autobahnen - Störungsursache: Arbeitsstellen" konnte Aufschluss darüber gegeben werden, wie sich die Reisezeitverluste auf Bundesautobahnen anteilsmäßig und in ihrer Größenordnung auf die genannten Störungsursachen aufteilen. Hierzu wurden im ersten Teil der Arbeit methodisch folgende Aspekte behandelt: - Aufbau eines Autobahnnetzmodells; - Modellierung der Verkehrsnachfrage; - Modellierung der Kapazität; - Staumodellierung und Ermittlung der Reisezeitverluste. Im zweiten Teil der Arbeit wurden die Ergebnisse der Verlustzeitberechnung für das Bezugsjahr 2000 ausführlich dokumentiert. In Sensitivitätsanalysen wurde die Stabilität der Berechnungsergebnisse hinsichtlich der Veränderung einzelner Eingangsdaten bestimmt. Dabei kommt der Modellierung der Verlagerung der Verkehrsnachfrage bei vorhandener Überlastung eine herausragende Bedeutung zu. Ohne Berücksichtigung dieser Verlagerung werden unplausible Werte berechnet, wobei die ermittelten Reisezeitverluste um ein Vielfaches höher als mit Berücksichtigung dieses Effekts liegen. Da zum Ausmaß der Verlagerung bislang keine Untersuchungen vorliegen, ist die Modellierung an dieser Stelle mit großen Unsicherheiten behaftet. In einer Gesamtbetrachtung wurden staubedingte Zeitverluste im Autobahnnetz für das Bezugsjahr 2000 zu insgesamt 234 Millionen Stunden und mit folgenden Anteilen abgeschätzt: Infrastrukturbedingte Engpässe 39%, Unfälle und Nothalte 26%, Arbeitsstellen 35%.
Zur Überwachung der Verkehrsentwicklung und zur Ermittlung der Verkehrsstärken auf den Bundesfernstraßen - Bundesautobahnen und Bundesstraßen - fand im Jahr 2005 wieder eine bundesweite Straßenverkehrszählung (SVZ 2005) im Rahmen des üblichen Fünfjahres-Turnus statt. Die Länder hatten die Möglichkeit, auch das nachgeordnete Netz (Landes- und Kreisstraßen) zu zählen und im Rahmen der SVZ 2005 auswerten zu lassen. Kreisstraßen wurden im Gegensatz zur SVZ 2000 nur in einigen Bundesländern und zudem nur in deutlich geringerem Maße erfasst, so dass zu dieser Straßenkategorie keine allgemeinen Aussagen getroffen werden können. Der vorliegende Bericht beinhaltet mittlere DTV-Werte und Jahresfahrleistungen, differenziert nach Fahrzeugarten und Straßenklassen sowohl für das Bundesgebiet insgesamt als auch für jedes einzelne Bundesland. Außerdem sind Beschreibungen zur Berechnung der DTV- und Fahrleistungsstatistiken enthalten sowie einige Ausführungen zu Entwicklungen der mittleren DTV-Werte und Jahresfahrleistungen in Bezug auf 2000.
Die Europäische Union hat sich zum Ziel gesetzt, die Anzahl der Getöteten im Straßenverkehr bis zum Jahr 2010 zu halbieren. Um dieses Ziel zu erreichen, ist es notwendig, sinnvolle Prioritäten zu setzen und effektive Straßenverkehrssicherheitsmaßnahmen umzusetzen. Den Entscheidungsträgern dient die ökonomische Bewertung dieser Maßnahmen als sachliches Kriterium bei der Auswahl der umzusetzenden Sicherheitsmaßnahmen. Nachfolgend wird ein Überblick darüber gegeben, wie Straßenverkehrssicherheitsmaßnahmen ökonomisch bewertet werden können, welche methodischen Prinzipien hierbei beachtet werden müssen, welche Daten notwendig sind und dem Evaluator zur Verfügung stehen und welche Barrieren bei der Bewertungsarbeit auftreten können. Darüber hinaus werden Beispiele bewerteter Maßnahmen und eine Kurzfassung über den Themenbereich der ökonomischen Bewertung in Form einer Power-Point Präsentation dargestellt. Die nachfolgend dargestellten Erkenntnisse wurden im Rahmen des EU Projekts ROSEBUD gewonnen.
Im September 2005 wurde erstmals eine FERSI Scientific Road Safety Research Conference durchgeführt. Mit der Konferenz sollten Resultate und Bearbeitungsstände der gemeinsamen europäischen Forschungsprojekte der FERSI Mitglieder präsentiert werden. Darüber hinaus sollten die Ergebnisse wichtiger nationaler Forschungsprojekte eingebunden sowie den Projektbearbeitern Gelegenheit zum internationalen "Networking" gegeben werden. Wolfgang Hahn, Leiter der Abteilung Straßenbau und Straßenverkehr beim Bundesministerium für Verkehr-, Bau- und Wohnungswesen unterstrich in seiner Eröffnungsrede die Notwendigkeit einer in Europa koordinierten Verkehrssicherheitsforschung, um gemeinsam zu einer Verbesserung der Straßenverkehrssicherheit zu gelangen. Aus Sicht des Leiters des Referates "Sicherheit im Straßenverkehr" der DG TREN, Dimitrios Theologitis, besteht die zentrale Aufgabe der zukünftigen europäischen Verkehrssicherheitsforschung in der Entwicklung und Verbreitung von "Best Practices". Auch er betonte, dass die Verkehrssicherheitsprobleme in Europa auch in Zukunft nur durch eine enge Zusammenarbeit der EU-Mitgliedsländer im Bereich der Forschung und durch die Umsetzung der dabei erzielten Forschungsergebnisse zu lösen seien.rnIm Anschluss an die Eröffnungsreden stellten Rune Elvik, TOI (Norwegen), Marc Gaudry, INRETS (Frankreich), David Lynam, TRL (United Kingdom) und Dr. Rudolf Krupp, BASt (Germany), in ihren Vorträgen herausragende Forschungsergebnisse im Bereich der Straßenverkehrssicherheit vor. Die sich an diese erste Vortragsrunde anschließenden Workshops waren entsprechend der Themenschwerpunkte "Daten, Strategien und Kommunikation", "Verhalten und Aufklärung" sowie "Technische Anwendungsmöglichkeiten" unterteilt. Jeder Themenschwerpunkt wurde durch 4 nacheinanderfolgende Workshops abgedeckt. In einer abschließenden Sitzung wurden die wichtigsten Ergebnisse der einzelnen Workshops vom jeweiligen Chairman des Workshops dem gesamten Plenum vorgestellt. rn
Zur Zustandsbeurteilung von Brückenfahrbahnplatten ist es wichtig, die Feuchte und den Salzgehalt des bewehrten Betons zu kennen. Üblicherweise wird die Versalzung mittels Potenzialmessung bestimmt und durch Laboranalyse von Proben verifiziert. Diese Methode erfordert aber das Entfernen des Fahrbahnbelags. Um eine zerstörungsfreie Bestimmung des Betonzustandes und des Salzgehaltes des Betons mit einem fahrzeugbasierten Messsystem von der Fahrbahn aus durchführen zu können, wurde eine Kombinationsmethode aus Georadar und Magnetfeldmessung entwickelt. Ermittelt man die komplexe Dielektrizitätskonstante (DK) des Baustoffs im Mikrowellen-Bereich, so ist es möglich, über entsprechende Kalibrationskurven seine Feuchte und seinen Salzgehalt abzuleiten. Mit einem 1 GHz-Bodenradar wird die Laufzeit der elektromagnetischen Wellen von der Fahrbahnoberfläche bis zur oberflächennahen Bewehrung bestimmt. Die Tiefe dieser Bewehrungsstähle wird unabhängig durch eine magnetische Gleichfeld-Methode ermittelt. Nach Aufmagnetisierung werden mehrere Gradientenkomponenten des statischen magnetischen Feldes der Bewehrungsbügel gemessen und daraus die Bügeltiefe berechnet. Diese magnetische Tiefenbestimmung ist unabhängig von den dielektrischen Eigenschaften der dazwischen befindlichen Materialien. Durch Vergleich der Radar-Laufzeit mit der magnetisch gemessenen Tiefe lässt sich der Realteil der effektiven DK des überdeckenden Betons bestimmen. Die Analyse der reflektierten Radar-Amplitude erlaubt eine Abschätzung des Salzgehaltes. Zusätzlich wurde ein dielektrischer Resonator für die Feuchte- und Salzgehaltmessung von Baustoffen entwickelt, der aus einer zylindrischen Mikrowellenkeramik hoher DK in einem halboffenen Metallgehäuse besteht. Aus der Messung der Resonanzfrequenz und der Güte beim Aufbringen des Resonators auf den Baustoff lässt sich sein Feuchte- und Salzgehalt ableiten. Die an Beton-Probekörpern bekannter Feuchte und Versalzung durchgeführten experimentellen Untersuchungen bestätigten die Erwartungen. Ein Radar-Magnet-Messwagen wurde entwickelt und auf zwei Brückenbauwerken erfolgreich erprobt. Die effektive komplexe DK konnte gut bestimmt werden.
Ziel des Vorhabens war es, ausgehend von dem für XF4-Betone anerkannten CDF-Prüfverfahren ein Laborprüfverfahren zu entwickeln, das einen abgeschwächten Frost-Tausalzangriff gemäß XF2-Exposition erzeugt und eine Beurteilung des Frost-Tausalzwiderstandes bei mäßiger Sättigung zulässt. Die am IBPM der Universität Duisburg-Essen durchgeführten Laborergebnisse verdeutlichen, dass eine Beurteilung des Widerstandes gegenüber einer XF2-Exposition über die Einstellung eines mäßigeren Feuchtegehaltes beziehungsweise Sättigungsgrades nicht eindeutig möglich ist. Dagegen ergab die Kombination der drei Prüfparameter - Minimaltemperatur "10-°C, 3%ige NaCl-Lösung und 14 FTW Prüfdauer - eine geeignete Abschwächung des CDF-Prüfverfahrens auf die Erfordernisse von XF2-Mischungen. Aufgrund der geringen Datenmenge ließ sich jedoch noch kein allgemein gültiger Grenzwert als Abnahmekriterium festlegen. Im Rahmen der Untersuchungen am cbm der TU München wurden Betone, die aufgrund ihrer Zusammensetzung für die Klassen XF4 und XF2 beziehungsweise für geringere Klassen als XF2 geeignet sind, sowohl durch Untersuchungen im Labor als auch durch Auslagerungsversuche beurteilt. Anhand der durch Auslagerung ermittelten Feuchtedaten wird deutlich, dass die Schädigung über die verschiedenen Winterperioden kumulativ zu sehen ist und nicht aus einer zunehmenden Sättigung des gesamten Probekörpers über mehrere Winter hinweg resultiert. Die Schädigung ist die Folge einer lokalen Übersättigung der äußersten Randzone, die jedoch weder durch Wägung des gesamten Probekörpers noch durch Messungen mit der Multiringelektrode erfassen werden konnte. Die Aufsättigung des Zementsteingefüges erfolgt bei Außenbauteilen aufgrund sich ändernder thermischer Randbedingungen und des damit verbundenen dynamischen Prozesses scheinbar in einer geringeren Schichtdicke als beim CDF-Verfahren. Folglich entstehen in der Praxis trotz vergleichbarer Anzahl an Frost-Tau-Wechseln geringere Schädigungen. Unabhängig davon erwies sich die Korrelation der Schädigung im Labortest und in der Praxis als sehr gut. Der modifizierte CDF-Test mit einer reduzierten Prüfdauer von 14 Frost-Tau-Wechseln und einer Minimaltemperatur von "10-°C spiegelt das Verhalten von XF2 Betonen praxisgerecht wieder.