Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (637) (entfernen)
Schlagworte
- Conference (386)
- Konferenz (382)
- Germany (212)
- Deutschland (209)
- Unfall (188)
- Accident (187)
- Safety (123)
- Sicherheit (122)
- Injury (117)
- Verletzung (117)
Institut
This paper deals with the determination of test criteria for the durability assessment of polyvinyl chloride (PVC)-based geosynthetic barriers (GBR-P) products in tunnel sealing systems. In the project different products for road tunnel application are investigated by systematic long time storage in hot water using a new test procedure based on SIA V 280 standard (test no. 13) and EN 14415. The objective of this research project is to derive suitable exposure conditions and criteria for a practical testing procedure with regard to service lifetimes of up to 100 years. For that test temperature and time as well as the best suitable test medium have been investigated in a structured way. To verify the results of the new test procedure the material properties of GBR-P samples removed from older road tunnels are investigated. Based on the presented results of the still on-going research program some preliminary conclusions regarding the updating of the German regulations for road tunnel sealing systems (ZTV-ING part 5 section 5 and TL/TP KDB) are given.
Straßentunnel mit integriertem Rettungsweg: Konstruktions- und betriebliche Sicherheitsaspekte
(2009)
Infolge der seit 2003 in den RABT formulierten schärferen Sicherheitsanforderungen ist für Gegenverkehrstunnel bei Neuplanungen und bautechnischen Nachrüstungen häufig die Anordnung eines parallel zur Hauptröhre verlaufenden Rettungsstollens erforderlich. Untersuchungen der Bundesanstalt für Straßenwesen (BASt) zur Wirtschaftlichkeit verschiedener aktueller und auch neuer Querschnittsvarianten haben gezeigt, dass insbesondere ein Querschnitt mit integriertem begehbarem Rettungsweg unter bestimmten Voraussetzungen Kostenvorteile gegenüber der Regellösung mit parallelem Rettungsstollen bietet. In ergänzenden Untersuchungen wurden konstruktive und sicherheitstechnische Detailfragen für einen Regelquerschnitt mit integriertem Rettungsweg untersucht und bewertet und ein Kostenvergleich mit der Regellösung mit parallelem Rettungsstollen wurde durchgeführt.
Tunnel in Spritzbetonbauweise werden in der Regel mit einem Abdichtungssystem aus Kunststoffdichtungsbahnen (KDB) gegen das anstehende Bergwasser abgedichtet. Die Tunnelabdichtungen aus KDB müssen dabei über die gesamte Nutzungsdauer des Bauwerks von in der Regel 130 Jahren zuverlässig ihre Funktion erfüllen. Ein einfacher Austausch der KDB oder der Einbau einer gleichwertigen Alternative ist in der Regel nicht, oder nur mit erheblichem Aufwand möglich. Bislang existieren national und international keine abgesicherten Prüfkriterien, die eine Bestimmung der Langzeitbeständigkeit von KDB über die geforderte Nutzungsdauer von mindestens 100 Jahren ermöglichen. Im vorliegenden Beitrag werden Untersuchungsergebnisse eines BASt Forschungsprojektes präsentiert, in dem Prüfkriterien für die Abschätzung der Langzeitbeständigkeit von KDB aus PVC-P hergeleitet werden. In diesem Projekt werden verschiedene marktübliche KDB für die Tunnelabdichtung mit einem beschleunigten Prüfverfahren "Lagerung in heißem Wasser" systematisch auf ihr Alterungsverhalten hin untersucht. Das hierfür verwendete Immersionsprüfverfahren wurde neu entwickelt und basiert auf der SIA V 280 (Prüfung Nr. 13) und DIN EN 14415. Ziel der Untersuchungen ist es, die erforderlichen Prüfkriterien zu definieren, die für eine praxisgerechte Abschätzung der Nutzungsdauer von mindestens 100 Jahren erforderlich sind. Hierfür werden beispielsweise die Einlagerungsdauer, die Einlagerungstemperatur und das Prüfmedium strukturiert untersucht. Zum Vergleich der Prüfergebnisse aus dem Immersionsprüfverfahren werden Untersuchungen an ausgebauten KDB Proben aus 2 älteren Straßentunneln herangezogen. Die Ergebnisse des Forschungsvorhabens sollen in die Fortschreibung des nationalen Regelwerks für den Straßentunnelbau (TL/TP KDB) einfließen.
Untersuchungen an in situ gealterten Kunststoffdichtungsbahnen aus Abdichtungen von Straßentunneln
(2011)
Tunnel in Spritzbetonbauweise werden in der Regel mit einem Abdichtungssystem aus Kunststoffdichtungsbahnen (KDB) gegen das anstehende Bergwasser abgedichtet. Zur Gewährleistung der Dauerhaftigkeit und Gebrauchstauglichkeit aber auch der Verkehrssicherheit (z.B. Gefahr der Glatteisbildung in undichten Tunneln) müssen die Tunnelabdichtungen aus KDB dabei über die gesamte Nutzungsdauer des Bauwerks von in der Regel 100 Jahren zuverlässig Ihre Funktion erfüllen. An der Entwicklung von Prüfverfahren zum Nachweis dieser Nutzungsdauer wird zurzeit national und international intensiv geforscht. Zur Verifizierung und Kalibrierung dieser Prüfverfahren können Untersuchungen an in situ gealterten KDB-Proben aus bestehenden Straßentunneln sehr nützlich sein. Im vorliegenden Beitrag werden erste Ergebnisse der Untersuchungen zu Materialeigenschaften von ausgebauten KDB Proben aus älteren Straßentunneln vorgestellt. Im Rahmen eines Forschungsprojektes der Bundesanstalt für Straßenwesen (BASt) wurden bereits zahlreiche Materialproben aus bestehenden Straßentunneln, die aktuell bautechnisch nachgerüstet werden, entnommen und untersucht. Bei der Entnahme der KDB-Proben wurde parallel auch die Bergwassertemperatur gemessen und an Bergwasserproben der Chemismus analysiert. Soweit möglich wurden die Produktdaten des Anlieferungs- bzw. Einbauzustandes beim Hersteller oder Bauherrn recherchiert, um so die Veränderungen der mechanischen Eigenschaften durch die in situ Alterung bewerten zu können. Die ermittelten mechanischen Eigenschaften nach Alterung wurden mit den Anforderungen damals gültiger und aktueller Regelwerke verglichen.
The Federal Highway Network of Germany represents considerable fixed assets. Construction and maintenance activities not only require a high budget, but also influence the traffic infrastructure and, thus, the economy and society as a whole. The present safety of the network has to be ensured under consideration of environmental aspects. At the same time the network owner has to make sure that the civil works are carried out in the most efficient way. Considering the fact that financial resources are restricted, the costs have to be spent in a way to obtain the greatest possible benefit. This task is supported by the application of a comprehensive Asset Management, which is subdivided into operational and controlling tasks respectively. The paper describes the current management procedures.
Allein im Netz der Bundesfernstraßen sind etwa 35.000 Brücken mit einer Fläche von 25 Millionen Quadratmetern enthalten. Ihr Wiederbeschaffungswert beträgt etwa 70 Milliarden DM. Es wird über die notwendigen Aktivitäten zur Erhaltung dieser für die Aufrechterhaltung des auf den Bundesfernstraßen rollenden Verkehrs besonders wichtigen Bauwerke berichtet. Aufgrund des weiter stärker werdenden Verkehrs, der zunehmenden Fahrzeuggewichte sowie der wachsenden Anzahl von Schwertransporten unterliegen insbesondere die älteren Bauwerke größerer Beanspruchung, als man bei ihrer Planung in Rechnung stellen musste. Hinzu kommt die natürliche Alterung aus sonstigen äußeren Einflüssen wie Temperatur, Witterung und erhöhter Umweltbelastung. Die Verwendung von Auftausalzen führt insbesondere bei älteren Brückenüberbauten zu Korrosionsschäden an der Bewehrung des Betons. Durch die Entwicklung eines Bauwerks-Management-Systems (BMS) wird die Verbesserung der Erhaltung von Brücken und sonstigen Ingenieurbauten angestrebt. Der Aufbau und die Wirkungsweise des BMS werden dargelegt. Des Weiteren werden die schon seit langem eingeführten Prüfvorschriften für Bauwerke im Zuge von Straßen und Wegen (DIN 1076) sowie gängige Prüfverfahren beschrieben.
BMS-Entwicklungen
(2002)
The Federal Ministry of Transport, Building and Housing is aiming for a comprehensive Management System taking into account state-specific and federal requirements as well as existing regulations in the frame of maintenance planning. The system is subdivided into three processes, each comprising special tools for valuation, analysing and planning. Some of the sub-modules have already been realised, eg the database at state level, the inspection procedure in combination with the procedures of damage and condition assessment and the estimation of future maintenance costs at federal level. Other sub-modules are currently being prepared, eg tools for evaluation and selection of measures. However, a large portion of the essential issues are still in the planning phase, eg program creation by taking restrictions into account. The realisation of the complete Management System will be finished by the year 2005.
The first stage of the work has been to collate information on bridge assessment from the participating countries. In the later stages, the aim is to provide guidelines that reflect the current best practices, a methodology that will allow for future development and sufficient flexibility to accommodate variations in national priorities as the process of harmonisation is pursued. The following tasks fall within the scope of the project: (1) a review of current procedures and standards used for bridge assessment in Europe; (2) the development of models for taking into account the bridge specific traffic conditions and material properties; (3) the use of reliability methods based on a probabilistic approach for bridge assessment including the use of measurements for updating the reliability of structural elements; and (4) the provision of recommendations for methods and procedures that can be adopted for the assessment module of the management framework highlighting where further development will be beneficial.
Brückenmanagement
(2001)
Die systematische Erhaltung der Brücken im Zuge der Bundesfernstraßen ist eine wichtige Aufgabe für den Baulastträger Bund und die Straßenbauverwaltungen der Länder. Um künftig Erhaltungsprogramme auf einer einheitlichen Grundlage unter Berücksichtigung gesamtwirtschaftlicher Grundsätze aufstellen zu können, wird durch die Bundesanstalt für Straßenwesen derzeit im Auftrag des Bundesministeriums für Verkehr, Bau- und Wohnungswesen ein umfassendes Bauwerks-Management-System (BMS) konzipiert und realisiert. Das geplante BMS beinhaltet alle Funktionen zur Durchführung des Erhaltungsmanagements. Grundlage ist die Erhebung und Bereitstellung von objektbezogenen Informationen. In Verbindung mit netzbezogenen Daten, Rahmenbedingungen und Restriktionen wird damit die Basis für Analyseprozesse, zum Beispiel Wirtschaftlichkeitsuntersuchungen, Priorisierungen und Bedarfsermittlungen bereitgestellt. Als Ergebnis werden Maßnahmenvorschläge, optimierte Programmplanungen und Angaben zum Finanzbedarf entwickelt. Verfahren und Programmsysteme werden schrittweise ab 2002 bis 2005 den Straßenbauverwaltungen zur Verfügung gestellt.
Germany's road infrastructure grew over centuries to become the arteries and lifelines of our society. The present safety of the infrastructure has to be ensured under consideration of environmental aspects. At the same time the owner has to make sure that the maintenance activities are carried out in the most efficient way. Considering the fact that financial resources are restricted, maintenance costs have to be spent in a way to obtain the greatest possible benefit. In the case of bridges, which are one of the most important parts of the road infrastructure in Germany, this task is supported by the application of a bridge management system (BMS). The existing German BMS contains assessment and optimization procedures on object and network level and is the basis for advancements to meet future demands. Developments concern life cycle and quality-oriented, holistically optimized procedures. Reasonable infrastructure management will contribute to meeting efficiency and sustainability objectives and to achieving interoperability. Here holistic network infrastructure management methods are required. There is a strong need for management solutions during the whole service life of a structure. The definition of criteria for evaluation of the relevance of failure mechanisms, including acceptance thresholds, requires the availability of relevant data for management procedure. Tools for innovative investigation methods and an effective data management will help in meeting the requirements. Relevant fields of research are improved maintenance strategies to meet future demands concerning heavy goods traffic, application and further development of nondestructive testing methods for efficient and sustainable management structures, and the improvement of analytic management tools to meet future demands.
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
Das Unfallgeschehen der Radfahrer wird analysiert. Ein erheblicher Anteil der Unfälle ereignet sich ohne Beteiligung motorisierter Fahrzeuge als Alleinunfall, bei Kollisionen mit Fußgängern oder Radfahrern. Viele Alleinunfälle werden nicht angezeigt, daher gibt es eine große Dunkelziffer. Das Schwergewicht der unfallbeteiligten Radfahrer liegt bei Kindern/Jugendlichen und bei Senioren. Der Anteil der Radfahrer als Hauptverursacher liegt bei ca. 47%. Hauptunfallstellen sind Kreuzungen und Einmündungen mit je über 28 %. Auf gesonderten Radwegen ist das Radfahren nur wenig sicherer als auf Straßen ohne Radwege; hinsichtlich der Unfallschwere ist das Bild uneinheitlich. Das Unfallgeschehen an Knotenpunkten wird genauer beschrieben.
Bus or heavy vehicle passenger accidents are rare events, compared with car accidents, but sometimes leads to a large number of victims especially in rollover crash scenarios. Two accidents occurred in Portugal in 2007 and 2013 in which 28 people died and more than 50 are injured, shown the importance of the investigation of such accidents. For the investigation of these accidents multidisciplinary teams are constituted with engineers and police officers. All the factors involved are taken into consideration including road design, traffic signs, maintenance and hardware, human factors, and vehicle factors. In this work a methodology to an accurate collection of the data is proposed. From the information collected the accident is reconstructed using the PC-CrashTM software. From this all the contribution factors are determined and recommendations to mitigate these crashes are listed. These two accidents are rollover accidents and the analysis of the injuries and its correlation with the use of retention systems is very important. From the medical data and with the dynamics of the accident determined simulations of the occupants with biomechanical models are carried out in order to evaluate the effect of the retention systems in the injuries. This analysis is based on injury criteria (such as Abbreviated Injury Score (AIS) or Injury Severity Scale (ISS)). With this it is possible to determine if the seat belt was worn or not.
Since its creation in 2011 the Pre-Crash-Matrix (PCM) offers the possibility to observe the pre-crash phase until five seconds before crash for a wide range of accidents. Currently the PCM contains more than 8.000 reconstructed accidents out of the GIDAS (German In-Depth Accident Study) database and is enlarged continuously by more than 1.000 cases per year. Hence, a detailed investigation of active safety systems in real accident situations has been made feasible. The PCM contains all relevant data in database format to simulate the pre-crash phase until the first collision of the accident for a maximum of two participants. This includes the definition of the participants and their characteristics, the dynamic behavior of the participants as time-dependent course for five seconds before crash as well as the geometry of the traffic infrastructure. The digital sketch of the accident and information from GIDAS as well as from supplementary databases represent the main input for the simulation of the pre-crash phase of an accident with the VUFO simulation model VAST (Vufo Accident Simulation Tool). This simulation in turn embodies the foundation of the PCM. The PCM underlies continual improvements and enhancements in consultation with its users. In addition to collisions of cars with other cars, pedestrians, bicycles and motorcycles the PCM now also covers car to object and car to truck collisions. The paper illustrates car to truck collisions as a showcase and explains perspectives for further developments. In 2016 a more detailed definition of the contour of the vehicle was added. Furthermore, the geometrical surroundings of the accident site will be provided in a new structure with a higher level of detail. Thus, a precise classification of road marks and objects is possible to further improve the support of developing and evaluating ADAS. This paper gives an overview about the latest developments of the PCM with its innovations and provides an outlook to upcoming enhancements. Besides potential areas of application for the development of ADAS are shown.
This work describes the results of the experimental activity, illustrating the driving behavior observed in different conditions, relating them to the different methods of ADAS intervention and comparing the driver behavior without ADAS. In the present study, driver behavior was studied in road accidents involving elderly pedestrians, with different ADAS HMIs, as a base to develop a driver model in near missing pedestrian accidents. A literature research was conducted with the aim of finding out the main influencing factors, including environment, boundary conditions, configuration of impact, pedestrian and driver information, when pedestrian fatalities occur and an analysis of frequent road accidents was conducted to get more detailed information about the driver- behavior. In order to obtain more detailed information about pedestrian accidents, real road accidents were reconstructed with multibody simulations on PC-Crash and, by the comparison between literature findings and reconstructions, a generic accident scenario was defined. The generic accident scenario was implemented on the full scale dynamic driving simulator in use at the Laboratory for Safety and Traffic Accident Analysis (LaSIS, University of Florence, Italy) in order to analyse the driving behaviors of volunteers, also considering the influence of ADAS devices. Forty-five young volunteers were enrolled for this study, resulting in forty valid tests on different testing scenarios. Two different scenarios consisted in driving with or without ADAS in the vehicle. Different kinds of ADAS, acoustic and optical, with different time of intervention were tested in order to study the different reactions of the driver. The tests showed some interesting differences between driver's behavior when approaching the critical situation. Drivers with ADAS reacted earlier, but more slowly, depending also on the type of alarm, and often with double reaction when braking. In fact, the results of the activity showed that with ADAS intervention the time to collision (TTC) increases, but the reaction time and braking modality change: a) there is a sort of "latency" time between the accelerator pedal release and the brake pressure; b) the brake pressure is initially less intense. So the driver only partially takes advance from the TTC increase. These differences were valued not only qualitatively, but quantitatively as well. This work revealed to be useful to improve the knowledge of drivers" behavior, in order to realize a driver model that can be implemented to help attaining and assessing higher levels of automation through new technology.
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
Causation of traffic accidents with children from the perspective of all involved participants
(2017)
In the year 2014 about 2,800 children between zero and 14 years got injured due to traffic accidents in Austria. More than 50% were taking part in traffic as active road users like cyclists or pedestrians. Within this study 46 real world traffic accidents between vehicles and children as pedestrians were analysed. In 39 cases, car drivers hit the crossing children. In the other cases, the collision opponents were busses, trucks or motorcycles. Most of the children got hit while crossing a road at urban sites. By analysing the traffic accidents from the perspectives of all involved participants, vehicle drivers and injured children, it is possible to identify factors for each participant, which led to the accident and factors that contributed the accident. The main task is to find patterns in the behaviour of crash victims (children and driver) before the collision. One important fact is that in more than 50% of the analysed cases sight obstructions were an important contributing factor for both, the driver and the child. From drivers view situations in which the child moved unexpected into the driven road lane were often found. For the injured child, factors like: no attention to the road traffic or no sufficient traffic observation were found to be relevant. Further it- possible to sensitise children and adults to possible source of critical traffic situations according to the findings of this study.
For more than a decade, ADAC accident researchers have analysed road accidents with severe injuries, recording some 20,000 accidents. An important task in accident research is to determine the causative factors of road accidents. Apart from vehicle engineering and human factors, accident research also focuses on infrastructural and environmental aspects. To find out what accident scenarios are the most common in ADAC accident research and what driver assistance systems can prevent them, our first task was to conduct a detailed accident analysis. Using CarMaker, we performed a realistic simulation of accident scenarios, including crashes, with varying parameters. To begin with, we made an initial selection of driver assistance systems in order to determine those with the greatest accident prevention potential. One important finding of this study is that the safety potential of the individual driver assistance systems can actually be examined. It also turned out that active safety offers even much more potential for development and innovation than passive safety. At the same time, testing becomes more demanding, too, as new systems keep entering the market, many of them differing in functional details. ADAC will continue to test all driver assistance systems as realistically as possible so as to be able to provide advice to car buyers. Therefore, it will be essential to develop and improve test conditions and criteria.
The proportion of older road users is increasing because of demographic change (in the group 65+ from current 18% to about 24% by 2030). The mobility needs of people 65+ often differ from those of younger people. Seniors (65+) are already more involved in fatal accidents than younger road users. According to the age development, the senior share of road deaths in the EU of today is increasing nearly one-fifth to one-third. From the in-depth analysis of accidents generic simulation models were developed. Attention has been paid both to psycho-physical characteristics as well as on the social and physical environment and their specifics in conjunction with seniors. By simulating the defined scenarios and varying the defined relevant parameters, accident influencing factors were examined as a basis for avoidance. In addition, the parameters were varied to show the influence from the vehicle, the pedestrian and the infrastructure to avoid the accident or to characterize the conditions for which the accident is inevitable.