Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (47) (entfernen)
Schlagworte
- Collision (47) (entfernen)
Institut
Methods for analyzing the efficiency of primary safety measures based on real life accident data
(2009)
Primary safety measures are designed to help to avoid accidents or, if this is not possible, to stabilize respectively reduce the dynamics of the vehicle to such an extent that the secondary safety measures are able to act as good as possible. The efficiency of a primary safety measure is a criterion for the effectiveness, with which a system of primary safety succeeds in avoiding or mitigation the severity of accidents within its range of operation and in interactionwith driver and vehicle. Based on Daimler-´s philosophy of the "Real Life Safety" the reflection of the real world accidents in the systems range of operation is both starting point as well as benchmark for its optimization. This paper deals with the methodology to perform assessments of statistical representative efficiency of primary safety measures. To be able to carry out an investigation concerning the efficiency of a primary safety measure in a transparent and comparable way basic definitions and systematics were introduced. Based on these definitions different systematic methods for estimating efficiency were discussed and related to each other. The paper is completed by presenting an example for estimating the efficiency of actual "single" and "multi" connected primary safety systems.
In a first step, we have examined approximately 23 000 single vehicle accidents within the Austrian National Statistics database. In a second step, we considered 15% of all fatal "running off the road" accidents that occurred in Austria in 2003. As a result, two accident categories were specified; "leaving the road without preceding manoeuvre" and "leaving the road with preceding manoeuvre". These two categories can be basically characterised by the vehicle- heading angle and its velocity angle. In this report, we further suggest theoretical approaches for the dimensioning of a safety zone, an area adjacent to the road free of fixed objects or dangerous slopes. We also show the link between the two accident categories mentioned above and the real world accidents analysed in detail. These observations also form the basis for the required length for safety devices. Finally, we summarise accident avoidance strategies.
Pedestrian accidents are one of the major concerns related with road accidents around the world. Portugal has one of the highest rates of pedestrian fatalities in Europe. In this paper an overview conditions were the pedestrian accidents occurred in Portugal is presented. In the last years, a project related with the pedestrian accidents has run in Portugal for the period 2004-2006 where 603 people died, 2097 have been severely injured and about 17000 slightly injured. Within this project all the pedestrian accidents in this period have been analysed providing global information about a wide range of aspects, since location, driver and pedestrian characteristics, weather and road conditions, among others. In addition, 50 in-depth accidents have been investigated and the data collected according the Pendant methodology. For this in-depth methodology detailed information about the accident has been collected, including injuries, vehicle damage, road conditions and road user- behaviour and actions. An accident reconstruction has been carried for each case including the determination of the speeds and driver actions, and the analysis of the contributing factors for the accident. Depending of the accident complexity, different methodologies have been used to analyse these accident, from the classical analytical equations such as Simms and Woods, to the use of detailed computational pedestrian models as those included in the commercial software- PC-Crash-® or Madymo-®. Also one of the goals of our investigation is the development of multibody models and methodologies for the reconstruction of pedestrian accidents. Some of these tools integrated in the commercial software Cosmos Motion-® are presented. The advantages of the different approaches are compared and discussed for some of the accidents investigated. With these tools the impact speed can be determined from the projection distance with analytical tools or PC-Crash-®, but more complex tools should be used to determine speed from the injuries, what is especially important for fatal accidents. The influence of the vehicle geometry and stiffness characteristics is another aspect analysed, where the influence of the vehicle stiffness has been determined using a combined multibody-finite elements approach within the software Madymo-®.
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
The aim of this study was to evaluate the performance and accuracy of Event Data Recorders (EDRs). The analysis was based on J-NCAP crash tests from 2006"2007, with the corresponding EDR datasets. The pre-crash velocity, maximum delta-V and delta-V versus time history data recorded in the EDRs were compared with the reliable crash test data. The difference between the EDR pre-crash velocity and the laboratory test speed was less than 4 percent. In contrast, in several cases the maximum delta-V and delta-V versus time history data obtained from the EDRs showed uncertainty of measurement in comparisons with the reliable delta-V data. The difference in maximum delta-V in these comparisons was more than 5 percent in 10 of 14 tests and more than 10 percent in 4 of 14 tests. The EDRs underestimated the maximum delta-V in almost all tests. It was also concluded that the calculated acceleration from the EDR delta-V versus time history data showed good agreement with the instrumented accelerometer signal during the collision in almost all tests.
Pedestrian and cyclist are the most vulnerable road users in traffic crashes. One important aspect of this study was the comparable analysis of the exact impact configuration and the resulting injury patterns of pedestrians and cyclists in view of epidemiology. The secondary aim was assessment of head injury risks and kinematics of adult pedestrian and cyclists in primary and secondary impacts and to correlate the injuries related to physical parameters like HIC value, 3ms linear acceleration, and discuss the technical parameter with injuries observed in real-world accidents based documented real accidents of GIDAS and explains the head injuries by simulated load and impact conditions based on PC-Crash and MADYMO. A subsample of n=402 pedestrians and n=940 bicyclists from GIDAS database, Germany was used for preselection, from which 22 pedestrian and 18 cyclist accidents were selected for reconstruction by initially using PC-Crash to calculate impact conditions, such as vehicle impact velocity, vehicle kinematic sequence and throw out distance. The impact conditions then were employed to identify the initial conditions in simulation of MADYMO reconstruction. The results show that cyclists always suffer lower injury outcomes for the same accident severity. Differences in HIC, head relative impact velocity, 3ms linear contiguous acceleration, maximum angular velocity and acceleration, contact force, throwing distance and head contact timing are shown. The differences of landing conditions in secondary impacts of pedestrians and cyclists are also identified. Injury risk curves were generated by logistic regression model for each predicting physical parameters.
The accident research of Hanover and (from 1999 on) Dresden registered 736 leg injuries (AIS ≥ 2) from 1983 to March 2007. 174 of these injuries (23.6 %) were fractures or dislocations of foot and ankle. 149 feet of 141 front seat car occupants in 140 cars were affected. Of these 117 were drivers, 24 were front seat passengers. The mean age of occupants was 38.5 -± 16.8 years. Ankle fractures were the most frequent injury (n = 82; 80 malleolar fractures, 2 pilon fractures). 34 fractures and dislocations affected the hindfoot (5 talus and 26 calcaneal fractures, 2 subtalar dislocations and 1 subtotal amputation) , 16 to midfoot (4 navicular fractures, 5 cuboid fractures, 3 fractures of cuneiformia, 2 dislocations of chopart joint, 1 subtotal amputation, and one severe decollement) and 39 the forefoot (metatarsal fractures). Open fractures were seldom seen (2 malleolar fractures, 1 metatarsal fracture). Both feet were injured in 10 cases. 33 occupants (23.4 %) were polytaumatic had a polytrauma, 17 of them died. 81 percent of the occupants were belted. The cars were divided in pre EuroNCAP (year of manufacture 1997 and older) and post EuroNCAP cars (year of manufacture 1998 and newer). Most of the foot injuries were seen in pre EuroNCAP cars. Most of the occupants sat in compact cars (40 drivers and 9 front seat passengers) and large family cars (27 drivers and 7 co-drivers). 49 of 140 accidents occurred on country roads, 26 on main roads and 13 on motorways. The crash direction was mostly frontal. Generally were found no differences of delta v- and EES-level between the injured foot regions, but divided into pre- and post-EuroNCAP cars there was a tendency to higher delta v- and EES-levels in newer cars. The frequency of foot injuries increased linearly with increasing delta v-level; but above delta v-level of 55 km/h the linear increase only was seen in pre-EuroNCAP cars, post-EuroNCAP cars showed no further increase of injuries. The footwell intrusion showed no difference between the injured foot regions but pre-EuroNCAP cars had a tendency to higher footwell intrusion. There were no differences in footwell intrusion between the car types. Only 29 of 174 fractures or dislocations of foot were seen in post-EuroNCAP cars, the predominate number of these injuries (n = 145) were noticed in pre-EuroNCAP cars. A lower probability of long-term impairment was found in post-EuroNCAP cars for equal delta v levels, using the AIS2008 associated Functional Capacity Index (FCI) for the foot region.
Since 2005, the motorcycle crash fatalities in the US exceeded 10% of the overall annual traffic fatalities. Consequently, it has become critical to gain in-depth understanding of the factors and characteristics contributing to motorcycle crashes. Unfortunately, there currently exists no database gathering the necessary information for an in-depth analysis of the US motorcycle crashes. So this study utilizes the NASS/CDS database (National Automotive Sampling System, Crashworthiness Data System) in order to gain insights into the patterns and factors leading to a NASS/CDS motorcycle crash, from 1997 to 2007. NASS/CDS samples about 5,000 passenger car tow-away crashes per year. Each case includes photographs and detailed data on crash and pre-crash characteristics, vehicle types, trajectories, types of impact, and other pertinent roadway and crash scene information, allowing an in-depth investigation of the crash mechanisms. However, the NASS/CDS sampling process specifically focuses on passenger car crashes, so the cases extracted only correspond to crashes in which a passenger vehicle was towed, and a motorcycle was somehow involved. Thus, a by-hand in-depth review of about 200 cases allowed retrieving 106 relevant crashes for this study, tending to represent the severe passenger vehicle(s) versus motorcycle(s) crashes on US roads. The findings lead to the conclusion that these crashes mostly result from the low conspicuity of the motorcycle, and from the inability of the car drivers to fully appreciate and anticipate the behavior of a motorcycle. Indeed, it has been shown that, first, the car drivers involved in these cases did not attempt any avoidance maneuver, second, they were largely of ages under 25, and finally, the majority of the crashes were in an intersection scenario. In addition, the two major scenarios unveiled were the car attempting a left turn from the opposite direction and the car attempting a left turn from the right. The paper mentions several solutions to enhance the motorcycle- conspicuity and to allow the car drivers to better anticipate its behavior, which seem to be key factors in the intersection-related crashes (and more generally in the passenger vehicle(s) versus motorcycle(s) crashes).
Recent findings from real-world accident data have shown that fatality risks for pedestrians are substantially lower than generally reported in the traffic safety literature. One of the keys to this insight has been the large and random sample of car-to-pedestrian crashes available in the German In-Depth Accident Study (GIDAS). Another key factor has been the proper use of weight factors in order to adjust for outcome-based sampling bias in the accident data. However, a third factor, a priori of unknown importance, has not yet been properly analysed. This is the influence of errors in impact speed estimation. In this study, we derived a statistical model of the impact speed errors for pedestrian accidents present in the GIDAS database. The error model was then applied to investigate the effect of the estimation error on the pedestrian fatality risk as a function of car impact speed. To this end, we applied a method known as the SIMulation-EXtrapolation (SIMEX) method. It was found that the risk curve is fairly tolerant to some amount of random measurement error, but that it does become flattened. It is therefore important that the accident investigations and reconstructions are of high quality to assure that systematic errors are minimised and that the random errors are under control.