Filtern
Erscheinungsjahr
Dokumenttyp
- Wissenschaftlicher Artikel (37) (entfernen)
Sprache
- Englisch (37) (entfernen)
Schlagworte
- Safety (9)
- Sicherheit (9)
- Deutschland (7)
- Germany (7)
- Behaviour (6)
- Bewertung (6)
- Verhalten (6)
- Europa (5)
- Europe (5)
- Evaluation (assessment) (5)
In most of the existing highway capacity manuals, level of service (LOS) of freeway weaving segments and ramp junctions is traditionally defined by the speed, volume or density in critical areas of merge, diverge and weaving manoeuvres. In that traditional concept several capacity values of different critical areas (merge, diverge, weaving) as well as upstream and downstream basic freeway segments within the influence areas are evaluated separately. In this paper, a new model which considers the total segment of freeway merge, diverge, and weaving as an entire object is introduced. A combined volume-to-capacity ratio is used for defining the LOS of the total segment. According to the probability and queuing theory, the volume-to-capacity ratio of the whole segment can be considered as a combination of volume-to-capacity ratios in the different critical areas under consideration. The parameters of the new model can be calibrated with field data. Those parameters are functions of the number of lanes on the freeways, the number of lanes in the on-ramps or off-ramps, the length of the acceleration, deceleration, or weaving sections. Varying the model parameters the function can be fitted to the existing capacity models for different types of weaving segments or ramp junctions. With this model, the traffic quality (LOS) can be obtained directly as a function of the volumes on the freeway and on the on-ramp or off-ramp respectively. The new model has the following advantages: a) a uniform function for all types of freeway weaving segments and ramp junctions, b) traffic quality assessment for all critical areas under investigation in one step, and c) easy calibration. The new model will be incorporated into the new edition of the German Highway Capacity Manual (HBS 201X).
As bearing capacity measurements become more and more important, the necessity of assuring quality by establishing a QA system becomes more relevant. Within this context, the FGSV recommends the introduction of comparative measurements. Since 2015, two pilot events took place, with the main aim of introducing repetitive comparative measurements, in which all FWD operators shall participate. The results of the comparative measurements show that the basic principles behind comparative measurements (of the FWD), elaborated as a Europe-wide consensus and put into practice in the Netherlands and the United Kingdom, are valid, but still there is a variety of questions to be answered concerning certain details of the measuring system itself, e. g. measurement of the temperatures (air, pavement) and the impact of load introduction. All in all, the two pilot events in 2015 and 2016 proved that the comparability of the different FWD measuring devices is satisfactory.
Although many German monitoring sites report declines of NOx concentrations, NO2-concentrations actually stagnate or even increase quite often. Various analyses have identified the altered compositions of nitrogen oxides (NO2/NOx-ratio) emitted by motor vehicles (resulting in an increase of primary NO2-emissions) as well as the chemical environmental conditions (mainly ground level ozone) as the main causes. The chemical conversion of NO to NO2 is often parameterized in dispersion calculations of exhaust emissions. A widely applied conversion model is the so-called Romberg approach from 1996. However, the Romberg approach has to be re-evaluated to accommodate the above-mentioned conditions. This article presents an adjustment to the Romberg approach in accordance with the measured data from 2000 to 2006, taking into consideration substantially higher NO2/NOx-ratios especially for higher NOx-concentrations. Model calculations with OSPM (Operational Street Pollution Model) including its internal chemistry module are able to reproduce very well the trends in the measured annual NO2-concentrations over a 10 year period. The relevant parameters for variations between the years are the NOx-emissions, primary NO2-emissions, ozone concentrations, wind conditions, and background concentrations. A simplified chemistry model based on annual mean NOx- and NO2-concentrations, and background ozone concentrations, as well as primary NO2-emissions is presented as a better method than the updated Romberg approach. This model simulates the annual mean NO2-concentrations much more accurately than the conventional and the updated Romberg approaches.
It is commonly agreed that active safety will have a significant impact on reducing accident figures for pedestrians and probably also bicyclists. However, chances and limitations for active safety systems have only been derived based on accident data and the current state of the art, based on proprietary simulation models. The objective of this article is to investigate these chances and limitations by developing an open simulation model. This article introduces a simulation model, incorporating accident kinematics, driving dynamics, driver reaction times, pedestrian dynamics, performance parameters of different autonomous emergency braking (AEB) generations, as well as legal and logical limitations. The level of detail for available pedestrian accident data is limited. Relevant variables, especially timing of the pedestrian appearance and the pedestrian's moving speed, are estimated using assumptions. The model in this article uses the fact that a pedestrian and a vehicle in an accident must have been in the same spot at the same time and defines the impact position as a relevant accident parameter, which is usually available from accident data. The calculations done within the model identify the possible timing available for braking by an AEB system as well as the possible speed reduction for different accident scenarios as well as for different system configurations. The simulation model identifies the lateral impact position of the pedestrian as a significant parameter for system performance, and the system layout is designed to brake when the accident becomes unavoidable by the vehicle driver. Scenarios with a pedestrian running from behind an obstruction are the most demanding scenarios and will very likely never be avoidable for all vehicle speeds due to physical limits. Scenarios with an unobstructed person walking will very likely be treatable for a wide speed range for next generation AEB systems.
Autonomous Emergency Braking (AEB) systems for pedestrians have been predicted to offer substantial benefit. On this basis, consumer rating programmes, e.g. Euro NCAP, are developing rating schemes to encourage fitment of these systems. One of the questions that needs to be answered to do this fully, is to determine how the assessment of the speed reduction offered by the AEB is integrated with the current assessment of the passive safety for mitigation of pedestrian injury. Ideally, this should be done on a benefit related basis. The objective of this research was to develop a benefit based methodology for assessment of integrated pedestrian protection systems with pre-crash braking and passive safety components. A methodology has been developed which calculates the cost of pedestrian injury expected, assuming all pedestrians in the target population (i.e. pedestrians impacted by the front of a passenger car) are impacted by the car being assessed, taking into account the impact speed reduction offered by the car’s AEB (if fitted) and the passive safety protection offered by the car’s frontal structure. For rating purposes, this cost can be normalised by comparing it to the cost calculated for selected cars. The methodology uses the speed reductions measured in AEB tests to determine the speed at which each casualty in the target population will be impacted. The injury to each casualty is then calculated using the results from standard Euro NCAP pedestrian impactor tests and injury risk curves. This injury is converted into cost using ‘Harm’ type costs for the body regions tested. These costs are weighted and summed. Weighting factors were determined using accident data from Germany and GB and the results of a benefit analysis performed by the EU FP7 AsPeCSS project. This resulted in German and GB versions of the methodology. The methodology was used to assess cars with good, average and poor Euro NCAP pedestrian ratings, with and without a current AEB system fitted. It was found that the decrease in casualty injury cost achieved by fitting an AEB system was approximately equivalent to that achieved by increasing the passive safety rating from poor to average. Also, it was found that the assessment was influenced strongly by the level of head protection offered in the scuttle and windscreen area because this is where head impact occurs for a large proportion of casualties. The major limitation within the methodology is the assumption used implicitly during weighting. This is that the cost of casualty injuries to body areas, such as the thorax, not assessed by the headform and legform impactors, and other casualty injuries such as those caused by ground impact, are related linearly to the cost of casualty injuries assessed by the impactors. A methodology for assessment of integrated pedestrian protection systems was developed. This methodology is of interest to consumer rating programmes which wish to include assessment of these systems. It also raises the interesting issue if the head impact test area should be weighted to reflect better real-world benefit.
This study aimed to better understand nitrate transport in the soil system in a part of the state of North Rhine-Westphalia, in Germany, and to aid in the development of groundwater protection plans. An advection-diffusion (AD) cell was used in a miscible displacement experiment setup to characterize nitrate transport in 12 different soil samples from the study area. The three nitrate sorption isotherms were tested to define the exact nitrate interaction with the soil matrix. Soils varied in their properties which in its turn explain the variations in nitrate transport rates. Soil texture and organic matter content showed to have the most important effect on nitrate recovery and retardation. The miscible displacement experiment indicated a decrease in retardation by increasing sand fraction, and an increase in retardation by increasing soil organic matter content. Soil samples with high sand fractions (up to 94 %) exhibited low nitrate sorption capacity of less than 10 %, while soils with high organic matter content showed higher sorption of about 30 %. Based on parameterization for nitrate transport equation, the pore water velocity for both sandy and loamy soils were significantly different (P < 0.001). Pore water velocity in sandy soil (about 4 x 10 high 3 m/s) was about 100 to 1000 larger than in loamy soils (8.7 x 10 high 5 m/s). On the other hand, the reduction in nitrate transport in soils associated with high organic matter was due to fine pore pathways clogged by fine organic colloids. It is expected that the existing micro-phobicity increased the nitrate recovery from 9 to 32 % resulting in maximum diffusion rates of about 3.5 x 10 high 5 m/s2 in sandy soils (sample number CS-04) and about 1.4 x 10 high 7 m/s2 in silt loam soils (sample number FS-02).
Urban runoff is known to transport a significant pollutant load consisting of e.g. heavy metals, salts and hydrocarbons. Interactions between solid and dissolved compounds, proper understanding of particle size distribution, dissolved pollutant fractions and seasonal variations is crucial for the selection and development of appropriate road runoff treatment devices. Road runoff at an arterial road in Augsburg, Germany, has been studied for 3.5 years. A strong seasonal variation was observed, with increased heavy metal concentrations with doubled and tripled median concentrations for heavy metals during the cold season. Correlation analysis showed that de-icing salt is not the only factor responsible for increased pollutant concentrations in winter. During the cold period, the fraction of dissolved metals was lower compared to the warm season. In road dust, the highest metal concentrations were measured for fine particles. Metals in road runoff were found to show a significant correlation to fine particles SS63 (<63 μm). Therefore, it is debatable whether treatment devices only implementing sedimentation processes provide sufficient removal rates.
Road authorities, freight, and logistic industries face a multitude of challenges in a world changing at an ever growing pace. While globalization, changes in technology, demography, and traffic, for instance, have received much attention over the bygone decades, climate change has not been treated with equal care until recently. However, since it has been recognized that climate change jeopardizes many business areas in transport, freight, and logistics, research programs investigating future threats have been initiated. One of these programs is the Conference of European Directors of Roads (CEDR) Transnational Research Programme (TRP), which emerged about a decade ago from a cooperation between European National Road Authorities and the EU. This paper presents findings of a CEDR project called CliPDaR, which has been designed to answer questions from road authorities concerning climate-driven future threats to transport infrastructure. Pertaining results are based on two potential future socio-economic pathways of mankind (one strongly economically oriented "A2" and one more balanced scenario "A1B"), which are used to drive global climate models (GCMs) producing global and continental scale climate change projections. In order to achieve climate change projections, which are valid on regional scales, GCM projections are downscaled by regional climate models. Results shown here originate from research questions raised by European Road Authorities. They refer to future occurrence frequencies of severely cold winter seasons in Fennoscandia, to particularly hot summer seasons in the Iberian Peninsula and to changes in extreme weather phenomena triggering landslides and rutting in Central Europe. Future occurrence frequencies of extreme winter and summer conditions are investigated by empirical orthogonal function analyses of GCM projections driven with by A2 and A1B pathways. The analysis of future weather phenomena triggering landslides and rutting events requires downscaled climate change projections. Hence, corresponding results are based on an ensemble of RCM projections, which was available for the A1B scenario. All analyzed risks to transport infrastructure are found to increase over the decades ahead with accelerating pace towards the end of this century. Mean Fennoscandian winter temperatures by the end of this century may match conditions of rather warm winter season experienced in the past and particularly warm future winter temperatures have not been observed so far. This applies in an even more pronounced manner to summer seasons in the Iberian Peninsula. Occurrence frequencies of extreme climate phenomena triggering landslides and rutting events in Central Europe are also projected to rise. Results show spatially differentiated patterns and indicate accelerated rates of increases.
Measuring and characterizing airborne particulate matter (PM) is an important research area because PM can lead to impacts on health and to visibility reduction, material damage and groundwater pollution. In regard to road dust, suspension and re-suspension and the contribution of non-exhaust PM to total traffic emissions are expected to increase as a result of predicted climate scenarios. European environmental regulations have been enforced to reduce exhaust particle emissions from road traffic, but little attention has been paid to reducing non-exhaust coarse particle emissions due to traffic. Therefore, a monitoring program for coarse PM has been initiated in early 2013 to assess the predicted increase in the abundance of non-exhaust particles. Particle sampling was performed with the passive-sampler technique Sigma-2. The subsequent single-particle analysis allows for characterization of individual particles, determination of PM size distribution, and calculation of PM mass concentrations. Two motorways n ear Cologne (Koeln), Germany were selected as sampling sites, and the experimental setup in the field was realized with a so-called twin-site method. The present study reports single-particle analysis data for samples collected between May 31, 2013 and May 30, 2014. Coarse PM, generated through multi-source mechanisms, consists of, e.g., tire-wear, soot aggregates, and mineral dust. The highest mass concentration occurs at both motorways in spring, and the observed PM mainly contains traffic-abrasion particles. The field measurements show that the minimum PM concentration was found in the 5 to 12-°C temperature range, whereas the maximum concentration was observed in both the "5 to 5-°C and the 12 to 24-°C ranges, in agreement with previous laboratory measurements. Correlation between super-coarse (d p 10"80 μm, geometric equivalent diameter) PM concentration and precipitation displays a significant increase in concentration with decreasing number of precipitation events (dry weather periods).
The goal of the project FIMCAR (Frontal Impact and Compatibility Assessment Research) was to define an integrated set of test procedures and associated metrics to assess a vehicle's frontal impact protection, which includes self- and partner-protection. For the development of the set, two different full-width tests (full-width deformable barrier [FWDB] test, full-width rigid barrier test) and three different offset tests (offset deformable barrier [ODB] test, progressive deformable barrier [PDB] test, moveable deformable barrier with the PDB barrier face [MPDB] test) have been investigated. Different compatibility assessment procedures were analysed and metrics for assessing structural interaction (structural alignment, vertical and horizontal load spreading) as well as several promising metrics for the PDB/MPDB barrier were developed. The final assessment approach consists of a combination of the most suitable full-width and offset tests. For the full-width test (FWDB), a metric was developed to address structural alignment based on load cell wall information in the first 40 ms of the test. For the offset test (ODB), the existing ECE R94 was chosen. Within the paper, an overview of the final assessment approach for the frontal impact test procedures and their development is given.
Trauma management (TM) covers two types of medical treatment: the initial one provided by Emergency Medical Services (EMS) and a further one provided by permanent medical facilities. There is a consensus in the professional literature that to reduce the severity and the number of road crash victims, the TM system should provide rapid and adequate initial care of injury, combined with sufficient further treatment at a hospital or trauma centre. Recognizing the important role of TM for reducing road crash injury outcome, it was decided, within the EU funded SafetyNet project, to develop road safety performance indicators (SPIs) which would characterize the level of TM systems" performance in European countries and enable country comparisons. The concept of TM SPIs was developed based on a literature study of performance indicators in TM, a survey of available practices in Europe and data availability examinations. A set of TM SPIs was introduced including 14 indicators which characterize five issues such as: availability of EMS stations; availability and composition of EMS medical staff; availability and composition of EMS transportation units; characteristics of the EMS response time, and availability of trauma beds in permanent medical facilities. Basic information on the TM systems was collected in close cooperation with the national expert group. A dataset with TM SPIs for 21 countries was created. It was demonstrated that the countries can be compared using selected TM SPIs. Moreover, a more general comparison of the TM systems' performance in the countries is possible, using multiple ranking and statistical weighting techniques. By both methods, final estimates were received enabling the recognition of groups of countries with similar levels of the TM system's performance. The results of various trials were consistent as to the recognition of countries with high or low level of the TM systems" performance, where in grouping countries with intermediate levels of the TM system's performance some differences were observed. The SafetyNet project's practice demonstrated that data collection for estimating TM SPIs is not an easy task but is realizable for the majority of countries. The TM SPIs" message is currently limited to the availability of trauma care services. Further development of the TM SPIs should focus on characteristics of actual treatment supplied, based on combined police and medical road crash related databases.
This article reports on a two-year study (2006 to 2008) of the distribution of de-icing salts (NaCl) applied to the road and the influence of traffic on the effective times of the de-icing salts. The research was focused on the needed resting periods of de-icing salts on road surfaces. The study used sensors installed in two lanes of the Motorway A4 in the area of the Dresden-Hellerau Highway Surveillance Center (Germany), to measure air and ground temperatures, wind speed and direction, liquid film thicknesses and residual quantities of salt on the road surface during ongoing traffic at 5-minute intervals. The authors conclude with four observations that can be useful for applying de-icing salts more judiciously: preventive spreading is only sensible if applied timely, i.e. immediately prior to icing events to be expected; the time-frame for preventive spreading on the dry road surface is maximum 60 minutes and on the moist road surface maximum 120 minutes; by increasing spreading densities in preventive spreading, this timeframe cannot be extended; it is completely sufficient if the spreading width is adjusted in such a way that the outer wheel tracks are also covered by the spreading. Distribution across the entire width of the lane will be caused by the rolling traffic within a few minutes.
Chronic non-cancer pain (CNCP) is a major health problem. Patients are increasingly treated with chronic opioid therapy (COT). Several laboratory studies have demonstrated that long-term use of opioids does not generally impair driving related skills. But there is still a lack of studies investigating on-the-road driving performance in actual traffic. The present study assessed the impact of COT on road-tracking and car-following performance in CNCP patients. Twenty CNCP patients, long-term treated with stable doses of opioid analgesics, and 19 healthy controls conducted standardized on-the-road driving tests in normal traffic. Performance of controls with a blood alcohol concentration (BAC) of 0.5 g/L was used as a reference to define clinically relevant changes in driving performance. Standard Deviation of Lateral Position (SDLP), a measure of road-tracking control, was 2.57 cm greater in CNCP patients than in sober controls. This difference failed to reach statistical significance in a superiority test. Equivalence testing indicated that the 95% CI around the mean SDLP change was equivalent to the SDLP change seen in controls with a BAC of 0.5 g/L and did not include zero. When corrected for age differences between groups the 95% CI widened to include both the alcohol reference criterion and zero. No difference was found in car-following performance. Driving performance of CNCP patients did not significantly differ from that of controls due to large inter-individual variations. Hence in clinical practice determination of fitness to drive of CNCP patients who receive opioid treatments should be based on an individual assessment.
Effects of time pressure on left-turn decisions of elderly drivers in a fixed-base driving simulator
(2019)
In countries with right lane traffic left-turn maneuvers at intersections are known to be particularly critical for elderly drivers. It has been suggested that the implementation and use of Advanced Driver Assistance Systems (ADAS) might offer a solution to compensate for age-related weaknesses in driving-related skills. In the present paper an experiment is reported which explored the effects of time pressure on the performance of left-turn manoeuvers supported by an ADAS function (time gap assistant). The study was performed in a fixed-base driving simulator with 20 younger (22-37) and 21 elderly drivers (60-84) who were observed when negotiating left-turn manoeuvers on rural roads with and without the assistance function active. Subjects performed the task once under conditions of time pressure once without. Results indicate that both age groups used the assistance function to perform the left-turn manoeuvers with shorter time gaps. Under conditions of time pressure this effect was more pronounced, and the effects of time pressure were stronger for the elderly. However, there were only weak indications for a specific benefit of the assistance function for the elderly.
This article describes the development of techniques to minimize automobile driver distraction when an in-vehicle information systems (IVIS) that requires visual attention is in use. The authors explain the visual occlusion technique that has been developed as a tool for the assessment of the in-vehicle human-machine interface (HMI) of IVIS in terms of visual demands. The authors addressed an unresolved issue in previous standardized experimental protocols - how subjects make use of the occluded intervals and how this might affect the assessments of visual demands. This study protocol assumed that subjects would continue task performance during occluded periods, leading to an underestimation of visual demands by the occlusion parameters "total shutter open time" (TSOT) and the "occlusion index". The authors predicted that a simple additional loading task to be performed in parallel could disrupt IVIS task performance during the occluded period leading to higher estimations of visual demands by TSOT and R. Their prediction was confirmed by the study findings. The results also showed that under the condition of additional auditory tracking, TSOT and R discriminated more clearly between an "easy" and a "difficult" IVIS task than under the standard condition. They conclude with a discussion of the implications of this research for designers of assessment tools for driver visual distractions.
Estimation of the effects of new emission standards on motorcycle emissions by means of modeling
(2016)
Road traffic is, in addition to the energy sector and the industry, one main source of air pollution and carbon dioxide emissions. Although most countries and manufacturers agreed to environmental regulations to reduce the pollutant emissions, particularly in urban areas with high traffic density, the impact of road traffic emissions on the environment and human health has been growing in importance steadily. Due to stricter emission standards and the binding use of emission-reducing systems (e.g. three-way catalyst) hydrocarbon emissions from passenger cars have been reduced significantly since the last two decades. Unlike to passenger cars the emissions standards of powered two-wheelers have not been adjusted since 2006 although their share of hydrocarbon emissions to the total amount of hydrocarbon emissions of road traffic is estimated to be disproportionately high. Due to the new regulation (EU) No. 168/2013 powered two-wheelers have to fulfill new emission standards from 2016 (Euro 4) and 2020 (Euro 5) onwards. Besides new limits for the tailpipe emissions the evaporative emissions are regulated separately for the first time, as they make up a high proportion to the total hydrocarbon emissions in this vehicle class. In this context, the calculation and forecast of road traffic emissions is an important tool to verify compliance of climate targets and to assess the reduction potential of emission-reducing systems. For that purpose the Federal Highway Research Institute (BASt) uses the emission- and calculation tool TREMOD (Transport Emission Model) which provides baseline data and calculated results for pollutants in almost every differentiation e.g. vehicle category, traffic situation and road type. Moreover, estimations of future emission trends, stock information and mileage distribution can be made. The main objective is to illustrate the impact of the upcoming emission standards Euro 4 and Euro 5 on the operational hydrocarbon emissions of powered two-wheelers based on statistical estimations. The significant aspect is to generate scenarios to show the reduction potential of hydrocarbon emissions of powered two-wheelers, differentiated into motorcycles and small motorcycles, in relation to the total share of hydrocarbon emissions in this vehicle class and to the total hydrocarbon emissions from road traffic. As a part of their research, the authors can make initial statements about the possible effect of the new emission standards of regulation (EU) No. 168/2013 by means of modeling with TREMOD.
Traditionally, traffic count statistics in Germany contain the so-called relevant hourly volume, which is defined as the 30th-highest hour of the year when listing the hourly volumes in descending order. When the first edition of the German Highway Capacity Manual (HBS) was prepared in 2001, the Federal Government decided that this 30th hour should be used as the basis for the level of service determination for all Federal freeways and trunk roads. While German freeways are quite well equipped with inductive loop detectors, there are much fewer counts on rural roads and almost no long-term data on urban roads. With the current redraft of the German HBS detailed advice will be given on how to estimate peak-hour demand (all vehicles and heavy vehicle portion), based on the n-th highest hour concept depending on the available traffic counts. As the HBS will be divided into three major parts: freeways, rural roads, and urban roads, three separate chapters for the peak-hour demand estimation will be provided. Whereas for freeways the task consists in finding the comparable site equipped with inductive loop detectors, for urban roads it is a matter of establishing which time periods of the year and weekdays are appropriate for manual short-term counts as estimation of the 30th hour of the year. For all kind of traffic devices the requirements on traffic demand models for level of service calculations are described.
This study was one part of the research activities of work package 5 "Rehabilitation" of the integrated EU DRUID project (6th Framework Programme). It aimed at gathering information about the cognitive"affective and behavioral processes that participants undergo while attending driver rehabilitation (DR) programs. The primary objective was to analyze the outcomes of group interventions for alcohol offenders in order to assess any cognitive, motivational and behavioral modifications within individual participants and to identify the relevant variables which initiate and support this change process. The general methodological concept of the study was a prospective cohort design of participants of group-based European driver rehabilitation programs, carried out via a participant feedback questionnaire survey. In total N=7.339 DUI offenders in 9 European countries (Austria, Belgium, France, Germany, Great Britain, Hungary, Italy, Netherlands and Poland) participated in the survey. The results indicate that DR participants feel such programs provide strong support for their cognitive and behavioral change processes. The findings suggest that participants feel encouraged to establish new behavioral goals and the commitment to stick to them. At the same time, the participants' ratings emphasize the important role of the course leader in encouraging such changes. The findings of this explorative questionnaire survey are promising. Although it is impossible to draw any conclusions regarding long-term behavioral changes or effects on recidivism rates, participants of DR courses express positive feedback on completion of the program. The positive outcomes of the study can motivate decisionmakers to launch DR measures and to regard them as an essential part of a comprehensive countermeasure system against DUI.
This paper presents findings of a laboratory experiment which aimed at evaluating the sensitivity and intrusiveness of Tactile Detection Response Task (TDRT) methodology. Various single-task, dual-task and triple-task scenarios were compared. The task scenarios included a surrogate of driving (tracking task) and different secondary tasks (N-back, surrogate reference task (SuRT)). The results suggest that the TDRT is sensitive to load levels of secondary tasks which primarily demand for cognitive resources (N-back). Sensitivity to variations of visual"manual load could not be shown (SuRT). TDRT seems also to be able to differentiate between modes of primary task which varies in terms of cognitive load (visual against auditory tracking task). Results indicated intrusiveness of TDRT on primary task performance and secondary task performance depending on the type of underlying task scenario. As a conclusion, TDRT can be recommended as a method to assess attentional effects of cognitive load of a secondary task, but should be used with caution for secondary tasks with strong motor demands.
At the end of each year, the German Federal Highway Research Institute (BASt) publishes the road safety balance of the closing year. They describe the development of accident and casualty numbers disaggregated by road user types, age groups, type of road and the consequences of the accidents. However, at the time of publishing, these series are only available for the first eight or nine months of the year. To make the balance for the whole year, the last three or four months are forecasted. The objective of this study was to improve the accuracy of these forecasts through structural time-series models that include effects of meteorological conditions. The results show that, compared to the earlier heuristic approach, root mean squared errors are reduced by up to 55% and only two out of the 27 different data series yield a modest rise of prediction errors. With the exception of four data series, prediction accuracies also clearly improve incorporating meteorological data in the analysis. We conclude that our approach provides a valid alternative to provide input to policy makers in Germany.
Immediate user self-evacuation is crucial in case of fire in road tunnels. This study investigated the effects of information with or without additional virtual reality (VR) behavioural training on self-evacuation during a simulated emergency situation in a road tunnel. Forty-three participants were randomly assigned to three groups with accumulating preventive training: The control group only filled in questionnaires, the informed group additionally read an information brochure on tunnel safety, and the VR training group received an additional behavioural training in a VR tunnel scenario. One week later, during the test session, all participants conducted a drive through a real road tunnel in which they were confronted with a collision of two vehicles and intense smoke. The informed and the behaviourally trained participants evacuated themselves more reliably from the tunnel than participants of the control group. Trained participants showed better and faster behavioural responses than informed only participants. Interestingly, the few participants in the control group who reacted adequately to the scenario were all female. A 1 year follow-up online questionnaire showed a decrease of safety knowledge, but still the trained group had somewhat more safety relevant knowledge than the two other groups. Information and especially VR behavioural training both seem promising to foster adequate self-evacuation during crisis situations in tunnels, although long term beneficial behavioural effects have to be demonstrated. Measures aiming to improve users/ behaviour should take individual difference such as gender into account.
The high density of commercial freight transport on motorways makes it difficult for truck drivers to find safe parking places especially for longer rest periods during the night. Even though expansions have been made to satisfy the demand in Germany, overcrowding and dangerous situations still occur as a result of vehicles parking on the entrance and exit roads of rest areas. In 2005 a control procedure called "Convoy Parking" was installed at the rest area Montabaur on the A3 motorway in Germany. Convoy Parking is subject to a patent (EP 1 408 455 B1, 2007). Convoy Parking requires all drivers entering their departure time at a terminal in front of a barrier. Subsequently, on the basis of the input data, the automatically detected vehicle length and the actual situation at the rest area, a free parking row is assigned and trucks can be parked sorted. The German Federal Highway Research Institute (BASt) developed a new control procedure called "Intelligent Controlled Compact Parking" (hereafter referred to as "Compact Parking" for short) to achieve that trucks are parking in a compact way, side by side and without a driving lane between trucks. Convoy Parking and Compact Parking have a very different control procedure and appearance. While Convoy Parking assigns a parking row to the driver, Compact Parking deliberately leaves the choice of the parking row to the drivers themselves. Drivers do not have to disclose their departure time to any system and they are not stopped by any barrier because Compact Parking offers a wide range of departure times on variable message signs. Drivers ought to use the parking row where their intended departure time is offered. With the innovative system Compact Parking the capacity of an existing rest area can be quickly increased without enlarging the area. This also avoids long-term planning approval procedures and is friendly to the environment. Besides, the safety for all users of the rest area can be improved by reducing illegal parking. Compact Parking is supported by the German Federal Ministry of Transport and Digital Infrastructure (BMVI). The first installation of Compact Parking is under construction at the rest area Jura-West on the A3 motorway (Northern Bavaria). The Autobahndirektion Nordbayern (Motorway Directorate for Northern Bavaria) is the central agency to plan, build and run the motorways in Northern Bavaria and got the approval of the BMVI to realize the pilot project. BASt accompanies the pilot project and leads the implementation of the control procedure. The opening is scheduled for summer 2015.
Non-point sources of traffic-related pollution become a major concern as they " compared to the point-source inputs " are more difficult to be defined or controlled. It is crucial to evaluate the fraction of traffic-related contamination that is transported to the road surroundings as it could negatively impact soil, surface water and groundwater. This study describes two means through which pollutants leave the road to the surrounding environment. Three German motorways were selected (A4, A555, and A61), where runoff and deposits were analyzed to determine pollutant load moving into the roadside soil or into the drainage system. Each of the three motorways carries approximately 70,000 vehicles a day on 4 to 6 driving lanes; and they cover a broad range of truck participation in the total traffic load ranging from 5.4% to 19.8%. The three motorways represent several topographical and landscape features as forest with noise barrier and parallel as well as perpendicular orientation to the main wind direction. Sampling of runoff and deposition was done on monthly basis. Bulk deposition was collected in Bergerhoff vessels at two heights (1.5 m and 0.3 m above the ground) and in 1 m, 2.5 m, 5 m and 10 m distances from the road edge. The results showed that heavy metals as well as large amounts of mineral compounds are moving from the driving lanes into the roadside environment. This includes sodium from applying deicing salts in winter seasons, which could be found in soil, dust and water samples. Calcium and iron were also detected in almost comparable concentrations. The annual deposition flow (bulk deposition) measured at a height of 1.5 m was higher than the comparative values for urban areas and background measuring points. The spatial distribution of material deposition showed clear differences between the three motorways. The pollutant load in deposition measured near the ground surface was higher than those measured at 1.5 m above the land surface. At all three sites, a clear negative correlation between pollutant load and the distance from the roadside could be found. Nearly 90% of the concentration values of heavy metals in road runoff were below or in the range of the test values for seepage water in the German Soil Protection and Contamination Ordinance. The pH-values around 7 in runoff and adjacent soil provide a good retention capacity in the soil for the heavy metal input.
The technology involved in traffic control in Germany has undergone significant changes. This paper describes how a group of German manufacturers have worked with operators to produce Open Communications Interface for Road Traffic Control Systems (OCIT). At the beginning of 2010, twenty-one different European manufacturers had bought licences for OCIT outstations.
This document describes the development and state of the art of orthotropic steel bridges in Germany. Following a short historical review of the performance of orthotropic bridge decks over the last decades, the present traffic loads are described and related to the resistance of the existing structures. Based on four different hazard categories, this paper describes different retrofitting methods. Although several promising strengthening techniques are introduced and evaluated, it appears that further research is urgently required in order to improve these techniques.