Sonstige
Supported by field accident data and monitoring results of European Regulation (EC) No. 78/2009, recent plans of the European Commission regarding a way forward to improve passive safety of vulnerable road users include, amongst other things, an extension of the head test area. The inclusion of passive cyclist safety is also being considered by Euro NCAP. Although passenger car to cyclist collisions are often severe and have a significant share within the accident statistics, cyclists are neither considered sufficiently in the legislative nor in the consumer ratings tests. Therefore, a test procedure to assess the protection potential of vehicle fronts in a collision with cyclists has been developed within a current research project. For this purpose, the existing pedestrian head impact test procedures were modified in order to include boundary conditions relevant for cyclists as the second big group of vulnerable road users. Based on an in-depth analysis of passenger car to cyclist accidents in Germany the three most representative accident constellations have been initially defined. The development of the test procedure itself was based on corresponding simulations with representative vehicle and bicycle models. In addition to different cyclist heights, reaching from a 6-year-old child to a 95%-male, also four pedal positions were considered. By reconstruction of a real accident the defined simulation parameters could be validated in advance. The conducted accident kinematics analysis shows for a large portion of the constellations an increased head impact area, which can reach beyond the roof leading edge, as well as high average values for head impact velocity and angle. Based on the simulation data obtained for the different vehicle models, cyclist-specific test parameters for impactor tests have been derived, which have been further examined in the course of head and leg impact tests. In order to study the cyclist accident kinematics under real test conditions, different full scale tests with a Polar-II dummy positioned on a bicycle have been conducted. Overall, the tests showed a good correlation with the simulations and support the defined boundary test conditions. Typical accident scenarios and simulations reveal higher head impact locations, angles and velocities. An extended head impact area with modified test parameters will contribute to an improved protection of vulnerable road users including cyclists. However, due to significantly differing impact kinematics and postures between the lower extremities of pedestrians and cyclists, these injuries cannot be addressed by the means of current test tools such as the flexible pedestrian legform impactor FlexPLI. Based on the findings obtained within the project as well as the existing pedestrian protection requirements a cyclist protection test procedure for use in legislation and consumer test programmes has been developed, whose requirements have been transferred into a corresponding test specification. This specification provides common head test boundary conditions for pedestrians and cyclists, whereby the existing requirements are modified and two parallel test procedures are avoided.
Das Fahren mit Licht am Tag wird seit dem 1. Oktober 2005 vom damaligen Bundesministerium für Verkehr, Bau und Stadtentwicklung (BMVBS) empfohlen. Weiterhin wurde im Februar 2011 auf europäischer Ebene beschlossen, alle neuen Fahrzeugtypen der Fahrzeugklasse M1 (Fahrzeuge zur Personenbeförderung mit vier Rädern und maximal 8 Sitzplätzen außer dem Fahrersitz) sowie der Fahrzeugklasse N1 (Kraftfahrzeuge zur Güterbeförderung mit mindestens vier Rädern und mit einem zulässigen Gesamtgewicht bis zu 3,5 t) mit speziellen Tagfahrleuchten (TFL) auszustatten. Seit August 2012 gilt diese Regelung auch für alle anderen Fahrzeugklassen. Vor dem Hintergrund dieser Entwicklung wird davon ausgegangen, dass sich das Fahren mit Licht am Tag immer weiter verbreitet. Um daraus resultierende Sicherheitsgewinne bewerten zu können, ist eine kontinuierliche Beobachtung der Lichteinschaltquoten am Tag erforderlich. Die Grundidee der kontinuierlichen Erfassung der Lichteinschaltquoten am Tag mit der angewendeten Erhebungsmethodik wird beschrieben. Im Fokus stehen die neuen Qualitätssicherungsmaßnahmen. Abschließend werden die bisher ermittelten Zeitreihen analysiert.
Car occupants have a high level of mortality in road accidents, since passenger cars are the prevalent mode of transport. In 2013, car occupant fatalities accounted for 45% of all road accident fatalities in the EU. The objective of this research is the analysis of basic road safety parameters related to car occupants in the European countries over a period of 10 years (2004-2013), through the exploitation of the EU CARE database with disaggregate data on road accidents. Data from the EU Injury Database for the period 2005 - 2008 are used to identify injury patterns, and additional insight into accident causation for car occupants is offered through the use of in-depth accident data from the EC SafetyNet project Accident Causation System (SNACS). The results of the analysis allow for a better understanding of the car occupants' safety situation in Europe, thus providing useful support to decision makers working for the improvement of road safety level in Europe.
In most of developed countries, the progress made in passive safety during the last three decades allowed to drastically reduce the number of killed and severely injured especially for occupants of passenger cars. This reduction is mainly observed for frontal impacts for which the AIS3+ injuries has been reduced about 52% for drivers and 38% for front passengers. The stiffening of the cars' structure coupled with the generalization of airbags and the improvement of the seatbelt restraint (load limiter, pretension, etc.) allowed to protect vital body regions such as head, neck and thorax. However, the abdomen did not take advantage with so much success of this progress. The objective of this study is to draw up an inventory on the abdominal injuries of the belted car occupants involved in frontal impact, to present adapted counter-measures and to assess their potential effectiveness. In the first part the stakes corresponding to the abdominal injuries will be defined according to types of impact, seat location, occupants' age and type of injured organs. Then, we shall focus on the abdominal injury risk curves for adults involved in frontal impact and on the comparisons of the average risks according to the seat location. In the second part we will list counter-measures and we shall calculate their effectiveness. The method of case control will be used in order to estimate odds ratio, comparing two samples, given by occupants having or not having the studied safety system. For this study, two type of data sources are used: national road injured accident census and retrospective in-depth accident data collection. Abdominal injuries are mainly observed in frontal impact (52%). Fatal or severe abdominal occupant- injuries are observed at least in 27% of cases, ranking this body region as the most injured just after the thorax (51%). In spite of a twice lower occupation rate in the back seats compared to the front seats, the number of persons sustaining abdominal injuries at the rear place is higher than in the front place. In recent cars, the risk of having a serious or fatal abdominal injury in a frontal impact is 1.6% for the driver, 3.6% for the front passenger and 6.3% for the rear occupants. The most frequently hurt organs are the small intestine (17%), the spleen (16%) and the liver (13%). The most common countermeasures have a good efficiency in the reduction of the abdominal injuries for the adults: the stiffness of the structure of the seats allows decreasing the abdominal injury risk from 54% (driver) to 60% (front occupant), the seatbelt pretensioners decrease also this risk from 90% (driver) to 83% (front passenger).
The incidence of side impacts was investigated from GIDAS data. Both vehicle-fixed object and vehicle-vehicle collisions were analysed as these are enclosed within the consumer testing program. Vehicle-fixed object collisions were stratified according to ESC availability. Results indicated that vehicles equipped with ESC rarely have pure-lateral impacts. An increase in oblique collisions was seen for the vehicles with ESC whereby most vehicle were driving in left curves. The analysis of vehicle-vehicle collisions developed injury risk curves were developed at the AIS3+ injury severity for the vehicle-vehicle side impacts. Results suggested that greatest injury risk occurred when a Pre Euro NCAP vehicle was struck by a Post Euro-NCAP vehicle. The remaining curves did not show different behaviour, indicating that stiffness increased have been equally combated. This was attributable to the few Post Euro-NCAP vehicles that had a deployed curtain airbag available in the sample. The integration of Euro NCAP testing has shown to improve vehicle crashworthiness for pole collisions, as those vehicles with ESC rarely incur lateral impacts.
Die vorliegende Studie liefert Ergebnisse zur Marktdurchdringung von Fahrzeugsicherheitssystemen im Jahr 2015. Wie bereits im Jahr 2013 wurde die Studie von infas und dem Institut fuer Kraftfahrzeuge (ika) durchgeführt. Dazu wurden 5.040 Haushalte zur Ausstattung eines ihnen zur Verfügung stehenden Fahrzeugs befragt und 56 Fahrzeugsicherheitssysteme ausgewählt. Neben den quantitativen Interviews wurden zwei Fokusgruppen mit Neu- bzw. Gebrauchtwagenkäufern durchgeführt. In der vorangegangenen Studie von 2013 wurden Experten befragt, die beruflich mit dem Ein- oder Verkauf von Pkw fuer Unternehmensflotten befasst sind. Die weiteste Verbreitung haben passive Sicherheitssysteme wie Airbags, die darauf abzielen, die Folgen eines Unfalls fuer die Beteiligten abzumildern. Aber auch aktive und intervenierende Systeme, die Risiken vermeiden oder einzelne Fahraufgaben übernehmen, gehören haeufig zur Fahrzeugausstattung. Die häufigsten Vertreter aus dieser Gruppe sind der Bremsassistent, ESP und der Tempomat. Die meisten Fahrzeugsicherheitssysteme sind in Fahrzeugen der oberen Mittelklasse und Oberklasse zu finden. Mit der jährlichen Fahrleistung und der Nutzungshäufigkeit nimmt die Anzahl der Systeme ebenso zu wie bei jüngeren Fahrzeugen und Dienstwagen. Die grössten Veränderungen gibt es im Segment der SUVs und Geländewagen. Hier steigt die Zahl der Neuzulassungen in den letzten Jahren deutlich und die Ergebnisse zeigen, dass diese Fahrzeuge häufig mit einer Vielzahl von Sicherheitssystemen ausgestattet sind. Die Ergebnisse aus der Vorgängerstudie zeigen, dass gewerbliche Fahrzeughalter solche Fahrzeugsicherheitssysteme in die Standardausstattung aufnehmen, deren Nutzen nachgewiesen ist. In der diesjährigen Studie wird deutlich, dass auch private Käufer Systeme insbesondere dann als sicherheitsrelevant und sinnvoll erachten, wenn sie durch den Gesetzgeber vorgeschrieben oder bereits seit längerer Zeit auf dem Markt etabliert sind. Es zeigt sich auch, dass insbesondere die eigene Erfahrung mit Sicherheitssystemen Vorurteile abbaut und zu einer positiven Einstellung gegenüber solchen Systemen führt.
High demands on exhaust emissions of passenger cars and light commercial vehicles require complex technologies. The three-way catalytic converter is an essential part of state of the art emission control systems. If a catalytic converter is damaged or its effectiveness deteriorates, it can be replaced by a replacement converter. Replacement catalytic converters from the aftermarket are approved on the basis of Regulation No 103 of the UNECE - United Nations Economic Commission for Europe. According to this regulation the replacement catalytic converter shall be designed, constructed and capable of being mounted so as to enable the vehicle to comply with the provisions taken as a basis for its type approval. Furthermore the pollution emissions must be effectively limited throughout the entire normal service life of the vehicle under normal operating conditions. In the context of the research project, the durability of replacement catalytic converters was examined. A VW Golf with emission standard Euro 4, 1.4 l petrol engine (55 kW) was selected as a test vehicle. At the start of the examinations, the vehicle showed a mileage of 75,000 km. The selected vehicle was regularly serviced in accordance with the manufacturer's specifications. No emission-relevant faults were recorded by the OBD system. The initial control measurement of the vehicle in as-delivered condition with the originally installed catalytic converter showed that the corresponding emissions of the regulated pollutants were considerably below the Euro 4 emission limits to be applied. Subsequently, an original replacement catalytic converter, which was purchased from an authorised dealer, and 4 catalytic converters purchased in the independent aftermarket, were examined. The replacement catalytic converters were conditioned according to the specifications of ECE Regulation No 103 and then measured in new condition. The catalytic converters were then aged on a burner test rig. Here a total mileage of 80,000 km was simulated. After 10,000 km and 40,000 km, the ageing was interrupted and the exhaust gas emissions of the test vehicle with the aged catalytic converters were measured. The examination was ended as soon as a limit value had been exceeded. The results of the project indicate that with the replacement systems for the after-treatment of exhaust gases available in the independent aftermarket, considerable quality differences can occur. At the end of the ageing over a distance of 80,000 km only the original replacement catalytic converter and one replacement catalytic converter from the independent aftermarket complied with the Euro 4 emission limits. With one replacement catalytic converter, the Euro 4 emission limits were already exceeded in new condition. With another replacement catalytic converter, the examination was aborted after 10,000 km ageing and with a further catalytic converter after 40,000 km ageing due to the Euro 4 emission limits being exceeded. The ECE Regulation No 103 provides for a test of durability of such systems over 80,000 km, but also alternatively enables the use of fixed deterioration factors. In practice, the durability of the replacement systems for the after-treatment of exhaust gases is guaranteed by their manufacturers. However, replacement catalytic converters are rarely inspected as part of the approval. In-use compliance provisions for replacement systems for the after-treatment of exhaust gases are not mentioned in the corresponding specifications. The results of this study indicate that the requirements in the ECE Regulation No 103 are not adequate to ensure the durability of replacement catalytic converters.
Die verschärften Anforderungen an das Emissionsverhalten von Pkw und leichten Nutzfahrzeugen haben aufwändige Technologien erforderlich gemacht. Ein wesentlicher Bestandteil aktueller Abgasnachbehandlungssysteme ist der Katalysator. Wenn ein Katalysator beschädigt wird oder seine Wirksamkeit nachlässt, kann er durch einen Austauschkatalysator ersetzt werden. Austauschkatalysatoren, die im Zubehörmarkt angeboten werden, werden auf Basis der Regelung Nr. 103 der Wirtschaftskommission der Vereinten Nationen für Europa (UNECE - United Nations Economic Commission for Europe) genehmigt. Entsprechend dieser Regelung muss der Austauschkatalysator so beschaffen sein und so eingebaut werden können, dass das Fahrzeug den Vorschriften der Regelungen entspricht, die bei seiner Typprüfung zu Grunde gelegt worden sind. Außerdem müssen die Schadstoffemissionen während der gesamten normalen Lebensdauer des Fahrzeuges unter normalen Betriebsbedingungen wirksam begrenzt werden. Im Rahmen des Forschungsvorhabens wurde die Dauerhaltbarkeit von Austauschkatalysatoren untersucht. Als Testfahrzeug wurde ein VW Golf der Abgasstufe Euro 4 mit einem 1.4-l-Benzinmotor (55 kW) ausgewaehlt. Bei Beginn der Untersuchungen wies das Fahrzeug eine Laufleistung von 75.500 km auf. Das ausgewählte Fahrzeug war regelmäßig entsprechend den Herstellervorgaben gewartet worden. Im OBD-System waren keine abgasrelevanten Fehler abgelegt. Bei der Eingangsmessung des Fahrzeuges im Anlieferungszustand mit dem ursprünglich verbauten Katalysator wurden die anzuwendenden Euro 4-Grenzwerte deutlich unterschritten. Anschließend wurden ein Original-Austauschkatalysator, der in einer markengebundenen Fachwerkstatt, und 4 Katalysatoren, die verdeckt im freien Teilemarkt beschafft worden waren, untersucht. Die Austauschkatalysatoren wurden entsprechend den Vorgaben der ECE Regelung Nr. 103 konditioniert und dann im Neuzustand vermessen. Anschließend wurden die Katalysatoren auf einem Brennerprüfstand gealtert. Dabei wurde eine Laufleistung von insgesamt 80.000 km simuliert. Nach 10.000 km und 40.000 km wurde die Alterung unterbrochen und die Abgasemissionen des Testfahrzeugs wurden mit den gealterten Katalysatoren gemessen. Sobald bei einem Katalysator eine Grenzwertüberschreitung festgestellt wurde, wurde die Untersuchung beendet. Die Ergebnisse der Untersuchung zeigen, dass bei im freien Teilemarkt erhältlichen Austauschsystemen zur Abgasnachbehandlung erhebliche Qualitätsunterschiede auftreten können. Nur mit dem Original-Austauschkatalysator und mit einem Austauschkatalysator, der im freien Markt beschafft worden war, konnten auch nach einer Alterung über 80.000 km die Euro 4 Grenzwerte eingehalten werden. Bei einem Austauschkatalysator wurden bereits im Neuzustand die Euro 4 Grenzwerte überschritten. Bei einem anderen Austauschkatalysator wurde die Untersuchung nach 10.000 km Alterung und bei einem weiteren Katalysator nach 40.000 km Alterung aufgrund einer Überschreitung der Euro 4 Grenzwerte abgebrochen. Die ECE Regelung Nr. 103 sieht eine Prüfung der Dauerhaltbarkeit derartiger Systeme über 80.000 km vor, ermöglicht jedoch alternativ die Verwendung von festen Verschlechterungsfaktoren. In der Praxis wird die Dauerhaltbarkeit der Austauschsysteme zur Abgasnachbehandlung von ihren Herstellern garantiert, eine Überprüfung findet im Rahmen der Genehmigung jedoch in den seltensten Fällen statt. Eine Feldüberwachung für Austauschsysteme zur Abgasnachbehandlung ist in den entsprechenden Vorschriften nicht vorgesehen. Die Ergebnisse dieser Untersuchung weisen darauf hin, dass die Anforderungen in der ECE Regelung Nr. 103 nicht ausreichen, um die Dauerhaltbarkeit von Austauschkatalysatoren sicherzustellen.
Mobility plays an important role in the Federal Republic of Germany. Motorised private transport and, consequently, passenger vehicles are the crucial factor. Vehicles should be environmentally and socially compatible yet also economically efficient at the same time. The crucial factor for pollution of the environment from road traffic is the exhaust emissions of the vehicles on the road. This is why, with the Directive 98/69/EC and the related introduction of exhaust emission standard Euro 3, the testing of the conformity of passenger and light commercial vehicles (in-service conformity check) was introduced. Vehicles already on the roads are to be examined again under type examination conditions (Type I Test) after a statistical selection process. In this way it is to be ensured that the systems and components relevant for the exhaust emissions of a vehicle will also function after several thousand kilometres. This is why the vehicles are checked again during in-service conformity check with respect to their limited pollution components. Due to the ever greater significance of CO2 emissions, both the CO2 emissions and the fuel consumption were included in this research project. For the success of such a project the choice of vehicle is of critical importance. Since this is the only way it is possible to also obtain a representative result. Therefore, in addition to the selection criteria required by law, statistical and technical criteria are also considered. The vehicle owners were selected on a random basis. All test vehicles were checked with respect to their pollutant components in the emissions laboratory in accordance with their standard. By law the same testing conditions apply in an in-service conformity check as in the relevant type approval. In this research project a total of 17 vehicle types were examined. Six types were equipped with positive-ignition engines and 11 types with compression ignition engines. Both groups were to each include vehicles of the limits Euro 4 and Euro 5. For vehicle types with positive-ignition engines, there was one type with the exhaust emission standard Euro 5. All others satisfied the exhaust emission standard Euro 4. For the vehicle types with compression ignition engines, 4 types satisfied exhaust emission standard Euro 5 and 7 types fulfilled exhaust emission standard Euro 4. Among the vehicle types with compression ignition and exhaust emission standard Euro4, there were 4 types of category M1 and 3 types of category N1 of class III. The aim of the research project is to examine the exhaust emissions in-service conformity of passenger and light commercial vehicles in operation to draw conclusions concerning the durability of engine components and systems for exhaust emission treatment. Overall in this in-service conformity testing programme, we were able, in accordance with the statistical procedure, to assess all 17 of the vehicle types tested as "positive". With the exception of one vehicle type, it was possible to conclude the random test for all vehicle types tested with the minimum random sample. This means that all 3 vehicles of one type in as-delivered condition complied with or fell below the respective limits for pollutant emissions according to the criteria of the statistical procedure. In the case of one vehicle type, where the random sample had to be enlarged, it was necessary to examine a total of 8 vehicles. Furthermore, with all vehicle types the CO2-emissions and fuel consumption (Type I Test) were determined to subsequently compare the measured CO2 emissions with those of the manufacturers. Of the 17 vehicle types examined, eleven vehicle types complied with the relevant manufacturers" values or fell below them. With six vehicle types, the CO2 emissions were more than the permissible 4% above the manufacturer- value during the Type I Test.
Mobilität spielt in der Bundesrepublik Deutschland eine wichtige Rolle. Dabei ist der motorisierte Individualverkehr und somit der Pkw-Verkehr die entscheidende Größe. Der Verkehr soll umweltgerecht, sozialverträglich aber auch gleichzeitig wirtschaftlich effizient sein. Entscheidend für die Schadstoffbelastung der Umwelt durch den Straßenverkehr sind die Abgasemissionen der im Verkehr befindlichen Fahrzeuge. Daher wurde mit der Richtlinie 98/69/EG und der damit verbundenen Einführung der Abgasstufe Euro 3 erstmalig die Prüfung der Konformität von in Betrieb befindlichen Personenkraftwagen und leichten Nutzfahrzeugen (Feldüberwachung) eingeführt. Dabei sollen bereits im Verkehr befindliche Fahrzeuge nach einer statistischen Auswahl unter Typprüfbedingungen (Typ I Test) erneut untersucht werden. So soll gewährleistet werden, dass die abgasrelevanten Systeme und Bauteile eines Fahrzeuges auch noch nach mehreren tausend Kilometern funktionieren. Deshalb werden die Fahrzeuge bei der Feldüberwachung auf ihre limitierten Schadstoffkomponenten ein weiteres Mal überprüft. Aufgrund der immer größeren Bedeutung der CO2-Emissionen wurden in diesem Forschungsvorhaben sowohl die CO2-Emissionen als auch der Kraftstoffverbrauch mit erfasst. Für den Erfolg eines solchen Projektes ist die Fahrzeugauswahl von entscheidender Bedeutung. Denn nur so ist es möglich auch ein repräsentatives Ergebnis zu erhalten. Deshalb wurden neben den gesetzlich vorgeschriebenen Auswahlkriterien auch statistische und technische Kriterien berücksichtigt. Dabei erfolgte die Auswahl der Fahrzeughalter nach dem Zufallsprinzip. Alle Prüffahrzeuge wurden im Abgaslabor, entsprechend ihrer Abgasnorm, auf ihre Schadstoffkomponenten überprüft. Gemäß der Gesetzgebung gelten bei einer Feldüberwachung die gleichen Prüfbedingungen wie bei der jeweiligen Typgenehmigung. In diesem Forschungsvorhaben wurden insgesamt 17 Fahrzeugtypen untersucht. Wobei 6 Typen mit Fremdzündungsmotor und 11 Typen mit Selbstzündungsmotor ausgestattet waren. Beide Gruppen sollten jeweils Fahrzeuge der Grenzwertstufen Euro 4 und Euro 5 beinhalten. Bei den Fahrzeugtypen mit Fremdzündungsmotor war ein Typ mit der Abgasnorm Euro 5, alle anderen erfüllten die Abgasnorm Euro 4. Bei den Fahrzeugtypen mit Selbstzündungsmotor erfüllten 4 Typen die Abgasstufe Euro 5 und 7 Typen entsprachen der Abgasstufe Euro 4. Unter den Fahrzeugtypen mit Kompressionszündung und der Abgasnorm Euro 4 befanden sich 4 Typen der Klasse M1 und 3 Typen der Klasse N1 der Gruppe III. Ziel des Forschungsvorhabens ist es, die Abgasemissionen von in Betrieb befindlichen Pkw und leichten Nutzfahrzeugen zu untersuchen, um so Rückschlüsse auf die Dauerhaltbarkeit von Motorkomponenten und Systemen zur Abgasnachbehandlung ziehen zu können. Insgesamt konnten bei dieser Feldüberwachung, gemäß dem statistischen Verfahren, alle 17 geprüften Fahrzeugtypen mit "positiv" bewertet werden. Mit Ausnahme eines Fahrzeugtyps, wurde bei allen untersuchten Fahrzeugtypen, die Stichprobe mit der Mindeststichprobengröße abgeschlossen. Das bedeutet, dass alle 3 Fahrzeuge eines Typs im Anlieferungszustand die jeweiligen Grenzwerte für Schadstoffemissionen gemäß den Kriterien des statistischen Verfahrens einhielten bzw. unterschritten. Nur bei einem Fahrzeugtyp war die Erhöhung der Stichprobe auf 8 Fahrzeuge erforderlich. Weiterhin wurden bei allen Fahrzeugtypen die CO2-Emissionen und der Kraftstoffverbrauch (Typ I Test) bestimmt, um anschließend die gemessenen CO2-Emissionen mit denen der Hersteller vergleichen zu können. Von den 17 untersuchten Fahrzeugtypen hielten elf Fahrzeugtypen die jeweiligen Herstellerangaben ein oder unterschritten diese. Bei sechs Fahrzeugtypen lagen die CO2-Emissionen um mehr als die bei der Typprüfung zulässigen 4% über der Herstellerangabe.