Sonstige
Filtern
Erscheinungsjahr
- 2017 (24) (entfernen)
Dokumenttyp
- Buch (Monographie) (13)
- Konferenzveröffentlichung (8)
- Bericht (2)
- Wissenschaftlicher Artikel (1)
Schlagworte
- Bewertung (24) (entfernen)
Institut
Bankettmaterialien müssen zwei Anforderungen erfüllen, die von verschiedenen Bestandteilen der Böden gewährleistet werden. Aufgrund der Verkehrssicherheit müssen sie eine dauerhaft hohe Tragfähigkeit aufweisen, damit von der Fahrbahn abkommende Fahrzeuge nicht einsinken und verunfallen. Die Tragfähigkeit und Standfestigkeit der Böden wird hauptsächlich durch den Kiesanteil der Böden erreicht. Da im Bereich des Banketts Straßenoberflächenwasser versickert, müssen sie andererseits ein möglichst hohes Schadstoffrückhalte- und -bindevermögen aufweisen, um den Untergrund und das Grundwasser zu schützen. Dies wird durch die Sand- und Feinanteile der Böden erreicht. Bei den bestehenden Bauweisen besteht nach Auffassung einiger Straßenbauverwaltungen der Länder ein Optimierungsbedarf. Im Rahmen dieser Forschungsarbeit sollten diese Bauweisen überprüft und ggf. weiter entwickelt werden, um noch stärker den bau-, als auch den umwelttechnischen Ansprüchen gerecht zu werden. Dabei werden die Bankette aus einem Gemisch von Gesteinskörnungen bzw. rezyklierten Baustoffen der Körnung 0/32 mm mit Feinkorn bzw. Oberboden hergestellt. Geeignete Zusammensetzungen waren durch Untersuchungen im Labor- und Technikumsmaßstab zu ermitteln. 18 Gemische von Gesteinskörnungen und Baustoffen der Körnung 0/32 mm mit unterschiedlichen Feinkorn- bzw. Oberbodenanteilen wurden in Bezug auf ihre Tragfähigkeit (CBR-Versuche) und Durchlässigkeit im Labor untersucht. Unter Berücksichtigung der Laborergebnisse wurden im Technikumsmaßstab Versuche mit vier Mischungen zur Ermittlung der Tragfähigkeit und des Verformungsverhaltens mittels statischen und dynamischen Verformungsmoduln durchgeführt. Basierend auf den Versuchsergebnissen sollte der Feinkornanteil der Bankettmaterialien einen Wert von 15 M.-% nicht übersteigen. Mit solchen Materialien sollte ein Verformungsmodul Ev2 ≥ 60 MN/m2 bzw. Evd ≥ 30 MN/m2 bei einem Verdichtungsgrad von DPr = 100 % sicher erreichbar sein. Falls eine höhere Tragfähigkeit für Bankette erforderlich ist, sollte der Feinkornanteil der Materialien ggf. weiter beschränkt werden.
This study investigates the protection offered by passive head-restraints with different stiffness and energy dissipation properties. For this purpose, computational multi-body models of a generic car seat and a biofidelic 50thpercentile male human for rear impact are used to study different seat designs and passive head-restraints. The validated seat-occupant model is also used in the design of two different car-seat models which are shown to effectively mitigate whiplash by utilising a crash-energy distribution technique. Five different passive head-restraints with varying stiffness (low-medium-high) and energy dissipation percentages (low-high) are successively attached to four different car-seat models. The simulation results indicate that the protection offered by head restraints is strongly dependent on the seat design. It has also been shown that the stiffness of the passive head-restraint has much more influence on whiplash-risk in comparison to its energy dissipation capacity.
As bearing capacity measurements become more and more important, the necessity of assuring quality by establishing a QA system becomes more relevant. Within this context, the FGSV recommends the introduction of comparative measurements. Since 2015, two pilot events took place, with the main aim of introducing repetitive comparative measurements, in which all FWD operators shall participate. The results of the comparative measurements show that the basic principles behind comparative measurements (of the FWD), elaborated as a Europe-wide consensus and put into practice in the Netherlands and the United Kingdom, are valid, but still there is a variety of questions to be answered concerning certain details of the measuring system itself, e. g. measurement of the temperatures (air, pavement) and the impact of load introduction. All in all, the two pilot events in 2015 and 2016 proved that the comparability of the different FWD measuring devices is satisfactory.
Whiplash injuries are characterized by the high variability of its symptoms and by the subjectivity of its diagnosis, which sometimes leads to frauds perpetrated by victims of rear-end impacts. It is estimated that whiplash injuries cost annually about 10.000 million Euros in Europe. Therefore, the aim of this study was to investigate the influence of the dynamics of the accident in which the victim was involved in the probability of development of whiplash associated injuries. In the presented methodology, first an accident reconstruction is performed where the dynamics of the accident is determined. This is carried out using the software PC-Crash, police and insurance companies' data. Then biomechanical injuries criteria related with whiplash injuries are evaluated. For the evaluation of the probability of having whiplash injuries, the Neck Injury Criterion (NIC) of the victim and the mean acceleration of the vehicle were evaluated. Then, with medical reports, the results of the accident reconstruction are correlated with the reported injuries. Some examples are presented. The results obtained indicate that the study of the dynamics of the road accidents in which the victims were involved could be used as an auxiliary of the prognosis of whiplash injuries and is important for a precise diagnosis of this type of injuries.