Sonstige
Filtern
Dokumenttyp
Schlagworte
- Active safety system (28) (entfernen)
Institut
- Sonstige (28) (entfernen)
Auf der Grundlage von 951 Unfallprotokollen aus den Jahren 1997 bis 2005, bei denen Bedienstete, Fahrzeuge oder Geräte der Straßenbauverwaltungen in Arbeitsstellen kürzerer Dauer (AkD) auf Autobahnen zu Schaden kamen, wurden relevante Unfallmuster herausgearbeitet. So konnte im Wesentlichen der Lkw als Hauptunfallverursacher mit einem Anteil von knapp 60 % am Gesamtunfallaufkommen identifiziert werden. Hauptsächlich sind AkD bei Sperrung des rechten Fahrstreifens oder des Standstreifens betroffen. Ein "Anprall von hinten" auf dem rechten Fahrstreifen und ein "seitliches Streifen" auf dem Standstreifen von zum Beispiel Absperrtafeln oder Fahrzeugen treten mit etwa gleichen Anteilen am häufigsten auf. Ferner zeigen die Auswertungen, dass 2/3 aller Unfälle bei stationären AkD aufgetreten sind. Besonders auffällig ist, dass fast 80 % der verunglückten Mitarbeiter in ihrem Fahrzeug zu beklagen sind, nur ca. 20 % der Verunglückten waren beim Unfall außerhalb der Fahrzeuge. Beim Ein- und Aussteigen sind nur 4 Unfälle dokumentiert, diese allerdings mit je zwei Getöteten und Verletzten. Hinsichtlich der relevanten Unfallmuster wurden Maßnahmen abgeleitet, die zum einen die Unfallvermeidung und zum anderen die Unfallfolgenminderung zum Ziel haben. Im Rahmen einer Abschätzung wurden diese Maßnahmen bewertet und das erwartete Reduzierungspotenzial, einerseits bezogen auf die Anzahl vermeidbarer Unfälle und andererseits auf die Vermeidung von Verletzten, abgeleitet. Die Maßnahmen zur Erhöhung der Sicherheit des Betriebsdienstpersonals in AkD wurden hinsichtlich ihrer Wirkungsweise (optisch, akustisch, haptisch) auf den Verkehrsteilnehmer bewertet. Aufgrund der haptischen Wirkungsweise auf die Verkehrsteilnehmer beim Überfahren von Warnschwellen könnte bei stationären AkD ein relativ großes Reduzierungspotenzial zu erreichen sein. Gleiches gilt auch beim Einsatz des Unfall-Vorwarn-Systems (UVS). Das größte Potenzial zur Vermeidung von Unfällen stellt die aktive Fahrzeugsicherheit bei den unfallverursachenden Verkehrsteilnehmern dar. Würden Lkw, die als Hauptunfallverursacher in Relation zu ihrer Fahrzeuganzahl deutlich überrepräsentiert sind, mit radarbasierten Fahrgeschwindigkeitsreglern und Spurassistenzsystemen ausgestattet, könnte mit relativ geringem Aufwand ein hohes Maß an Sicherheit erzielt werden. Nutznießer einer solchen Pflichtausstattung wären darüber hinaus natürlich auch alle anderen Verkehrsteilnehmer, die bei Auffahrunfällen etc. davon profitieren würden. Auf die Installation von aktiven Sicherheitssystemen in Fahrzeuge kann nur durch entsprechende Vorgaben des Gesetzgebers Einfluss genommen werden. Empfehlenswert erscheint außerdem der Einsatz von Unfalldatenschreibern (UDS) inklusive der Dokumentation des Fahrerverhaltens wie zum Beispiel Festhalten des Lenkrades, um den Unfallhergang im Nachhinein rekonstruieren zu können. Insgesamt bieten passive Schutzsysteme in den Betriebsdienstfahrzeugen wegen der hohen Anteile von Verunglückten in den Fahrzeugen das größte Potenzial zur Vermeidung von Verletzungen. So könnten bereits durch die generelle Empfehlung zum Anlegen des Sicherheitsgurtes, auch bei der Absicherung von Arbeitsstellen oder Kurzfahrten, rund 30 % der zu erwartenden verletzten Fahrzeuginsassen vermieden werden. Zur Unterstreichung dieser Maßnahme sollte in entsprechenden Sicherheitsunterweisungen auf die Unfallgefahr hingewiesen werden. Diese sollten nicht nur das jederzeit gegenwärtige Gefährdungsrisiko ins Bewusstsein rufen, sondern auch die Eigensicherung, wie zum Beispiel erhöhte Aufmerksamkeit beim Ein- und Aussteigen, das Anlegen der Sicherheitsgurte, die korrekte Sitzposition sowie die persönliche Kopfstützeneinstellung betreffen. Ein sehr großes Vermeidungspotenzial insbesondere von HWS-Verletzungen bieten zum Beispiel Nackenairbags, aber auch Kopfstützensysteme in Verbindung mit Gurtstraffern mit zu erwartenden Reduzierungen von über 80 % der Verunglückten in den Fahrzeugen.
The project UR:BAN "Cognitive assistance (KA)" aims at developing future assistance systems providing improved performance in complex city traffic. New state-of-the-art panoramic sensor technologies now allow comprehensive monitoring and evaluation of the vehicle environment. In order to improve protection of vulnerable road users such as pedestrians and cyclists, a particular objective of UR:BAN is the evaluation and prediction of their behaviour and actions. The objective of subproject "WER" is development support by providing quantitative estimates of traffic collisions at the very start and predict potential in terms of optimized accident avoidance and reduction of injury severity. For this purpose an integrated computer simulation toolkit is being devised based on real world accidents (GIDAS as well as video documented accidents), allowing the prediction of potential effectiveness and future benefit of assistance systems in this accident scenario. Subsequently, this toolkit may be used for optimizing the design of implemented assistance systems for improved effectiveness.
The evaluation of the expected benefit of active safety systems or even ideas of future systems is challenging because this has to be done prospectively. Beside acceptance, the predicted real-world benefit of active safety systems is one of the most important and interesting measures. Therefore, appropriate methods should be used that meet the requirements concerning representativeness, robustness and accuracy. The paper presents the development of a methodology for the assessment of current and future vehicle safety systems. The variety of systems requires several tools and methods and thus, a common tool box was created. This toolbox consists of different levels, regarding different aspects like data sources, scenarios, representativeness, measures like pre-crash-simulations, automated crash computation, single-case-analyses or driving simulator studies. Finally, the benefit of the system(s) is calculated, e.g. by using injury risk functions; giving the number of avoided/mitigated accidents, the reduction of injured or killed persons or the decrease of economic costs.
Since its creation in 2011 the Pre-Crash-Matrix (PCM) offers the possibility to observe the pre-crash phase until five seconds before crash for a wide range of accidents. Currently the PCM contains more than 8.000 reconstructed accidents out of the GIDAS (German In-Depth Accident Study) database and is enlarged continuously by more than 1.000 cases per year. Hence, a detailed investigation of active safety systems in real accident situations has been made feasible. The PCM contains all relevant data in database format to simulate the pre-crash phase until the first collision of the accident for a maximum of two participants. This includes the definition of the participants and their characteristics, the dynamic behavior of the participants as time-dependent course for five seconds before crash as well as the geometry of the traffic infrastructure. The digital sketch of the accident and information from GIDAS as well as from supplementary databases represent the main input for the simulation of the pre-crash phase of an accident with the VUFO simulation model VAST (Vufo Accident Simulation Tool). This simulation in turn embodies the foundation of the PCM. The PCM underlies continual improvements and enhancements in consultation with its users. In addition to collisions of cars with other cars, pedestrians, bicycles and motorcycles the PCM now also covers car to object and car to truck collisions. The paper illustrates car to truck collisions as a showcase and explains perspectives for further developments. In 2016 a more detailed definition of the contour of the vehicle was added. Furthermore, the geometrical surroundings of the accident site will be provided in a new structure with a higher level of detail. Thus, a precise classification of road marks and objects is possible to further improve the support of developing and evaluating ADAS. This paper gives an overview about the latest developments of the PCM with its innovations and provides an outlook to upcoming enhancements. Besides potential areas of application for the development of ADAS are shown.
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
The main focus of the benefit estimation of advanced safety systems with a warning interface by simulation is on the driver. The driver is the only link between the algorithm of the safety system and the vehicle, which makes the setup of a driver model for such simulations very important. This paper describes an approach for the use of a statistical driver model in simulation. It also gives an outlook on further work on this topic. The build-up process of the model suffices with a distribution of reaction times and a distribution of reaction intensities. Both were combined in different scenarios for every driver. Each scenario has then a specific probability to occur. To use the statistical driver model, every accident scene has to be simulated with each driver scenario (combinations of reaction times and intensities). The results of the simulations are then combined regarding the probabilities to occur, which leads to an overall estimated benefit of the specific system. The model works with one or more equipped participants and delivers a range for the benefit of advanced safety systems with warning interfaces.
The sequence of accident events can be classified by three essential phases, the pre-crash-sequence, the crash-sequence and the post-crash-sequence. The level of reliability of the information in the GIDAS-database (German In Depth Accident Study) is provided predominantly on the passive side. The period to evaluate active safety systems begins already in the pre-crash-sequence. The assessment of the potential of sensor- or communication-based active safety systems can only be accomplished by a detailed analysis of the pre-crash-phase. Hence the necessity to analyze the early period of the accident event in detail arises. This is possible with the help of the digital sketches of the accident site and the simulation of the accident by a simulation method of the VUFO GmbH. After simulating the pre-crash scenario it is possible to generate additional and standardized data to describe the pre-crash-sequences of an accident in a very high detail. These data are documented in a second database called the GIDAS Pre-Crash-Matrix (PCM). The PCM contains various tables with all relevant data to reproduce the pre-crash-sequence of traffic accidents from the GIDAS database until 5 seconds before the first collision. This includes parameters to describe the environment data, participant data and motion or dynamic data. This paper explains the creation of the PCM, the simulation itself and the contents and structure of the PCM. With this information of the pre-crash-sequence for various accident scenarios an improved benefit estimation and development of active safety systems can be made possible.
The data situation for quantifying the proportion of accidents avoided by the introduction of active safety systems is incomplete, since there is generally no data available on the accidents avoided by the technology in question. In this paper, a split-register approach is suggested and compared with the classical case-control approach known from epidemiologic applications. Provided a set of assumptions hold, which can reasonably be made in such data situations, the split register approach allows inferences on the population accident risk. For both approaches the benefits of basing the analysis on the results of a logistic regression to adjust for confounding factors are outlined. The biasing effects of violating key assumptions are discussed and the split-register approach is demonstrated using the example of the active safety system ESP with data from the German in-depth accident study GIDAS.
Neben der zunehmenden Bedeutung der aktiven Sicherheit bleiben Maßnahmen der passiven Sicherheit bei der Entwicklung moderner Kraftfahrzeuge unabdingbar. Die Weiterentwicklung von Maßnahmen zum passiven Fußgängerschutz war zunächst größtenteils durch Verbraucherschutztests wie zum Beispiel Euro NCAP oder JNCAP getrieben und ist nun auch durch gesetzliche Regelungen verpflichtend geworden. Im vorangegangenen Forschungsprojekt der BASt FE 82.229/2002 Schutz von Fußgängern beim Scheibenaufprall ist die Grundlage eines modularen Prüfverfahrens für den Kopfaufprall im Bereich der Windschutzscheibe, bestehend aus einem Versuchs- und einem Simulationsteil, erarbeitet worden. Im Rahmen dieses Projektes wurde ein hybrides Testverfahren bestehend aus Versuch und Simulation ausgearbeitet, das den Bereich der Windschutzscheibe und dabei auch crashaktive Systeme wie Airbags berücksichtigt. Das Testverfahren kombiniert Komponentenversuche mit einem Simulationsteil, in dem Fahrzeug-Fußgänger-Simulationen und lmpaktorsimulationen durchgeführt werden. Zusätzliche Dummyversuche dienten zur Bewertung des Testverfahrens. Alle erarbeiteten virtuellen und realen Testmethoden wurden an einem Referenzfahrzeug (Opel Signum), welches repräsentativ für eine durchschnittliche Mittelklasselimousine steht, durchgeführt. Das Fahrzeug wurde mit einem Airbagsystem ausgerüstet und der Testprozedur mit und ohne diesem System vergleichend unterzogen. Innerhalb dieser Untersuchungen konnte gezeigt werden, dass neue Testmethoden unter Ausnutzung von Simulationen und Komponententests es erlauben, realistischere Versuchsbedingungen unter Berücksichtigung von potenziellen Kopfaufprallpositionen und -zeiten zu definieren. Dabei können sehr gute Übereinstimmungen zwischen Fußgängersimulation und Dummyversuch erreicht werden. Die Randbedingungen für den Kopfaufprall und die Aufprallzeit wurden durch den Einsatz von Fußgängermodellen ermittelt. Weiterhin ermöglichen die Simulationen, zusätzliche Einflussdaten wie Vektoren mit den Kopfaufprallgeschwindigkeiten und -winkeln zu bestimmen.
The presentation deals with the simulation tool rateEFFECT which intends to answer the following questions: Which active safety systems should be developed to maximize safety benefit in real traffic accidents? What is the effectiveness of a specific active safety system in the real world? How many casualties could be avoided by such a system? It is shown that a lot of information is required to simulate existing accidents in order to estimate ADAS effects. This particularly includes numerical values for the pre-crash and in-crash phase. The database GIDAS provides a required minimum number of these parameters for a statistically significant sample.