Sonstige
Filtern
Dokumenttyp
Volltext vorhanden
- ja (23) (entfernen)
Schlagworte
- Insasse (23) (entfernen)
Institut
- Sonstige (23)
- Abteilung Fahrzeugtechnik (2)
Every second counts when human lives are at stake. The increasingly safe design of vehicles presents rescuers with a serious challenge. Faced with high-strength steels and body reinforcements, even the most powerful cutters reach their limits. Therefore, incident commanders require information on the technical features and components installed, directly in the vehicle. Several tests have shown that such information helps to save valuable minutes. Therefore, a standardised A4 "rescue sheet" containing information on the location of cabin reinforcements, the tank, the battery, airbags, gas generators, control units etc. " and indicating adequate cutting points must be used throughout Europe. Hopefully, in a few years, the new eCall emergency call system will be in place everywhere in Europe. The system will transmit the relevant vehicle-specific data directly to the rescuers on-site. Until then, we need a simple and effective solution that saves lives.
A total survey of road traffic accidents involving most severely injured, defined as sustaining a polytrauma or severe monotrauma (ISS > 15) or being killed, was conducted over 14 months in a large study region in Germany. Data on injuries, pre-clinical and clinical care, crash circumstances and vehicle damage were obtained both prospectively and retrospectively from trauma centers, dispatch centers, police and fire departments. 149 patients with a polytrauma and eight with a severe monotrauma were recorded altogether. 22 patients died in hospital. Another 76 victims had deceased at the accident scene. In 2008, 49 % of patients treated with life-threatening injuries were car or van occupants, 21 % motorcyclists, 18 % cyclists and 10 % pedestrians. Among fatalities at the scene, vehicle occupants constituted an even larger portion. The number of road users with life-threatening trauma in the region was extrapolated to the German situation. It suggests that 10 % among the "seriously injured" as defined in national accident statistics are surviving accident victims with a polytrauma or severe monotrauma.
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
Testverfahren zur Bewertung und Verbesserung von Kinderschutzsystemen beim Pkw-Seitenaufprall
(2003)
Die gegenwärtige europäische Regelung zur Prüfung und Zulassung von Kinderschutzsystemen (KSS) für Pkw (ECE-R44-03) beinhaltet dynamische Tests zur Frontal- und Heckaufprallsimulation. Der Seitenaufprall ist bisher nicht berücksichtigt, obwohl die Verletzungsschwere und die Folgekosten groß sind. Im Gegensatz zum Frontal- und Heckaufprall ist der Seitenaufprall gekennzeichnet durch eine direkte Lasteinleitung durch intrudierende Strukturen. Das Kinderschutzsystem und das Kind werden durch große Kontaktkräfte direkt beaufschlagt. Verletzungen des Kopfes und Halsbereichs von Kindern in KSS sind hierbei häufig und schwer. Seit 1993 beschäftigt sich daher eine ISO-Arbeitsgruppe (International Standardization Organisation) mit der Entwicklung eines Testverfahrens zur Prüfung von KSS beim Seitenaufprall. Die Ziele und entsprechende Ideen sowie Konzepte beteiligter Parteien sind bis heute kontrovers, so dass bisher keine endgültige Einigung im Rahmen der Arbeitsgruppe erzielt werden konnte. Ziel der vorliegenden Arbeit als Abschluss eines Projekts der BASt (Bundesanstalt für Straßenwesen) und dem Fachgebiet Kraftfahrzeuge der TU Berlin ist es, die komplexe Problematik zu dem Thema umfassend darzustellen und gleichzeitig einen ganzheitlichen Lösungsvorschlag anzubieten. Hierzu sind die Teilergebnisse der ISO-Arbeitsgruppe im ersten Schritt strukturiert und analysiert worden. Wissenslücken wurden detektiert und in einem weiteren Schritt beseitigt. Alle Teilergebnisse wurden im Rahmen der ISO-Arbeitsgruppe präsentiert, diskutiert und größtenteils auch akzeptiert. Der aktuelle Stand der ISO-WG1 ist somit maßgeblich von den hier erzielten Ergebnissen beeinflusst. Als Kern der vorliegenden Arbeit ist an der TU Berlin das Konzept für ein Testverfahren entwickelt, umgesetzt und geprüft worden. Die wesentlichen Parameter des realen Seitenaufpralls wie: - Beschleunigungsniveau des gestoßenen Pkw, - Delta-v des gestoßenen Pkw, - Maximalintrusion beim gestoßenen Pkw sowie - die maximale Intrusionsgeschwindigkeit im Kopfbereich sind wiedergegeben. In Abgrenzung zu aktuellen, komplexen Schlittentestverfahren, die z.B. zur Entwicklung von Seitenairbags dienen, ist die statische und dynamische Intrusionsgestalt einer realen Pkw-Seitenstruktur hingegen stark vereinfacht, aber ausreichend dargestellt. Die Ergebnisse zeigen, dass es prinzipiell möglich ist, das Schutzpotential von rückwärtsgerichteten sowie vorwärtsgerichteten KSS mit dieser Prozedur zu analysieren. Die Seitenaufprallabbildungsgüte ist hoch bei einer gleichzeitig sehr guten Reproduzierbarkeit der Messergebnisse. So zeigen die Tests, dass die Kinematik des Kopf- und Halsbereichs im Wesentlichen von der Gestalt des KSS im Seitenbereich abhängig ist. Ausreichend große Seitenwangen können den Kopf flächig stützen und vermeiden so den direkten Kontakt zu intrudierenden Strukturen. Gleichzeitig wird die starke laterale Inklination der Halswirbelsäule reduziert. Die Belastungen am Kopf sind aber bei allen getesteten KSS hoch und liegen deutlich oberhalb diskutierter Grenzwerte. Bei genauer Betrachtung der KSS-Seitenwangenpolsterung fällt auf, dass diese entweder gar nicht oder nur rudimentär vorhanden ist. Modifikationen, die abschließend an KSS vorgenommen wurden, zeigen aber auf, dass bereits durch einfache technische Maßnahmen die Belastungen im Kopfbereich signifikant gesenkt werden können. Das mit dieser Arbeit vorgelegte Testverfahren bietet KSS-Herstellern wie auch dem Gesetzgeber die Möglichkeit, Schwächen von KSS aufzudecken und Modifikationen zielgerichtet durchzuführen. Durch die Berücksichtigung des realen Seitenaufpralls ist gewährleistet, dass alle Optimierungen seitens der KSS-Hersteller auch positiven Einfluss auf die passive Sicherheit von Kindern in Pkw haben können. Eine maximale Reduktion der schwer bzw. tödlich verletzten Kinder als Pkw-Insassen in Höhe von ca. 10% ist bei 100%-iger Marktdurchdringung mit optimal gestalteten Produkten realistisch. Dies entspricht einer Verringerung der Anzahl getöteter Kinder um ca. 10 sowie schwerverletzter Kinder um ca. 200 pro Jahr in Deutschland.
Introduction: Spine injuries pose a considerable risk to life and quality of life. The total number of road deaths in developed countries has markedly decreased, e.g. in Germany from over 20000 in 1970 to less than 4000 in 2010, but little is known how this is reflected in the burden of spine fractures of motor vehicle users. In this study, we aimed to show the actual incidence of spine injuries among drivers and front passengers and elucidate possible dependencies between crash mechanisms and types of injuries.
In most of developed countries, the progress made in passive safety during the last three decades allowed to drastically reduce the number of killed and severely injured especially for occupants of passenger cars. This reduction is mainly observed for frontal impacts for which the AIS3+ injuries has been reduced about 52% for drivers and 38% for front passengers. The stiffening of the cars' structure coupled with the generalization of airbags and the improvement of the seatbelt restraint (load limiter, pretension, etc.) allowed to protect vital body regions such as head, neck and thorax. However, the abdomen did not take advantage with so much success of this progress. The objective of this study is to draw up an inventory on the abdominal injuries of the belted car occupants involved in frontal impact, to present adapted counter-measures and to assess their potential effectiveness. In the first part the stakes corresponding to the abdominal injuries will be defined according to types of impact, seat location, occupants' age and type of injured organs. Then, we shall focus on the abdominal injury risk curves for adults involved in frontal impact and on the comparisons of the average risks according to the seat location. In the second part we will list counter-measures and we shall calculate their effectiveness. The method of case control will be used in order to estimate odds ratio, comparing two samples, given by occupants having or not having the studied safety system. For this study, two type of data sources are used: national road injured accident census and retrospective in-depth accident data collection. Abdominal injuries are mainly observed in frontal impact (52%). Fatal or severe abdominal occupant- injuries are observed at least in 27% of cases, ranking this body region as the most injured just after the thorax (51%). In spite of a twice lower occupation rate in the back seats compared to the front seats, the number of persons sustaining abdominal injuries at the rear place is higher than in the front place. In recent cars, the risk of having a serious or fatal abdominal injury in a frontal impact is 1.6% for the driver, 3.6% for the front passenger and 6.3% for the rear occupants. The most frequently hurt organs are the small intestine (17%), the spleen (16%) and the liver (13%). The most common countermeasures have a good efficiency in the reduction of the abdominal injuries for the adults: the stiffness of the structure of the seats allows decreasing the abdominal injury risk from 54% (driver) to 60% (front occupant), the seatbelt pretensioners decrease also this risk from 90% (driver) to 83% (front passenger).
Im Rahmen der Optimierung des Sicherheitssystems Reisebusverkehr beauftragte die Bundesanstalt für Straßenwesen (BASt) das Institut für Fahrzeugtechnik an der Fachhochschule Trier eine Schwachstellenanalyse zur Optimierung des Notausstiegssystems bei Reisebussen durchzuführen. Die Bearbeitung des Projektes geschah in den folgenden Einzelschritten: Die entsprechenden Paragraphen des nationalen und europäischen Regelwerkes wurden in Anlage V systematisch zusammengestellt und verglichen. Ergänzend wurden die teilweise erheblich abweichenden Regelungen in den USA, Japan und Australien betrachtet. Eine erste Schwachstellenanalyse aus Hersteller- bzw. Konstrukteurssicht wurde erstellt. Darauf folgten Expertengespräche in der Fahrzeug- und Zulieferindustrie sowie international tätigen Prüforganisationen. Hier wurden die bestehenden bzw. sich in der Entwicklung befindlichen konstruktiven Lösungen von Rohbau, Umbau und Innenausstattung von Reisebussen ermittelt und systematisiert. Eine zweite Schwachstellenanalyse beinhaltete die Sicht des Gebrauchs und Missbrauchs sowie des Notfalls und der Rettung. Als Ausgangslage dienten Einsatzberichte und Befragungen von Feuerwehr und Technischem Hilfswerk (THW) sowie Unfallgutachten. Als nächster Schritt wurden Evakuierungsversuche am Reisebus in Seitenlage durchgeführt. Sie dienten dazu, die bisher gewonnenen Erkenntnisse näher zu untersuchen, zu ergänzen und zu belegen sowie neue Erkenntnisse zu gewinnen. Die Evakuierungsversuche wurden durch CAD-Simulationen erweitert. In einem Workshop mit Experten aller betroffenen Bereiche wurden die erarbeiteten Schwachstellen und Lösungsmöglichkeiten diskutiert, systematisiert und hinsichtlich ihrer Relevanz bewertet. Die gewonnenen Erkenntnisse wurden zu einem "Lastenheft für ein optimiertes Notausstiegssystem bei Reisebussen" zusammengefasst. Die nach der Bearbeitung der oben genannten Arbeitspunkte noch offenen Fragen wurden als Forschungsbedarf formuliert. Der Originalberichte enthält als Anlagen einen Auszug aus den Federal Motor Vehicle Safety Standards (FMVSS 217, USA) (I), die Fragenkataloge für Bushersteller (II), Busunternehmen (III) und Feuerwehren (IV), eine Zusammenfassung der europäischen Regelungen (V), den Fragebogen Gruppenversuche (VI) sowie die Teilnehmerliste des Expertengespräches (VII). Auf die Wiedergabe dieser Anlagen wurde in dieser Veröffentlichung verzichtet. Sie liegen bei der Bundesanstalt für Straßenwesen vor und sind dort einsehbar. Verweise auf die Anlagen im Berichtstext wurden beibehalten.
Detailed anthropometric data of pregnant women have been collected and used in the development of a computational model of the pregnant occupant model "Expecting". The model is complete with a finite element uterus and multi-body fetus, which is a novel feature in the models of this kind. The computational pregnant occupant model has been validated and used to simulate a range of impacts. The strains developed in the utero-placental interface are used as the main criteria for fetus safety. Stress distributions due to inertial loading of the fetus on the utero-placental interface play a role on the strain levels. Inclusion of fetus model is shown to significantly affect the strain levels in the utero-placental interface. This series of studies has led to the design of seatbelt features specifically for the pregnant women to enable them use the seatbelt correctly and comfortably.
From an automotive safety occupant protection standpoint, effective occupant restraint requires a system capable of providing non-injurious occupant ride down of anticipated crash forces. This is not only the case for frontal collisions, where occupant restraint is provided primarily by seatbelts and airbags, but is also critical for other crash modes such as side impacts, rear impacts, rollovers, as well as multiple impact events. In the rear impact crash mode, occupant restraint is provided primarily by the seatbacks and to some extent the seatbelts. Foundationally, therefore, what becomes fundamental to the seatback's role in rear occupant protection is its ability to contain the occupant within the seat, preventing occupant ramping, as well as preventing the seat's, and/or its occupant's, dangerous intrusion into the rear occupant's survival space where contact with rear compartment components and/ or rear seated occupants can present a significant injury risk. An analysis is presented of a series of rear impact sled testing conducted by the authors that evaluates the timing, position and extent of the front seatback's reward displacement toward and into the rear occupant compartment as well as consideration of the front seat occupant' ramping potential and its injury potential relative to the rear compartment. Additionally, three other series of testing are presented which assess various seat designs occupant retention capabilities. Lastly, a matched-pair comparison test series is presented which evaluates occupant motion in rear impact with and without use of a typical vehicle body mounted 3-point seatbelt. Discussion of restraint system performance observed in all the testing is included along with ATD biofidelity and thigh-gap considerations. The data collected and presented includes accelerometer instrumentation and high speed video analysis.
Empirical vehicle crashworthiness studies are usually based on national or in-depth traffic accident surveys: Data on accident-involved cars/drivers are analysed in order to quantify the chance of driver injury and to assess certain risk factors like car make and model. As the cars/drivers involved in the same accident form a "cluster", where the size of the cluster equals the number of accident-involved parties, traffic accident survey data are typical multi-level data with accidents as first-level or primary and cars/drivers as secondlevel or secondary units (car occupants in general are to be considered as third level units). Consequently, appropriate statistical multi-level models are to be used for driver injury risk estimation purposes as these models properly account for the cluster structure of traffic accident survey data. In recent years various types of regression models for clustered data have been developed in the statistical sciences. This paper presents multi-level statistical models, which are generally applicable for vehicle crashworthiness assessment in the sense that data on single and multiple car crashes can be analysed simultaneously. As a special case of multi-level modelling driver injury risk estimation based on paired-by-collision car/driver data is considered. It is demonstrated that assessment results may be seriously biased, if the cluster structure inherent in traffic accident survey data is erroneously ignored in the data analysis stage.