Abteilung Straßenverkehrstechnik
Filtern
Dokumenttyp
Sprache
- Englisch (17) (entfernen)
Schlagworte
- Safety (6)
- Sicherheit (6)
- Autobahn (5)
- Deutschland (5)
- Germany (5)
- Measurement (5)
- Messung (5)
- Motorway (5)
- Lorry (4)
- Air pollution (3)
Institut
The first version of German Highway Capacity Manual was published in 2001. Now, a new version is published in 2015 (HBS 2015). For the new German Highway Capacity Manual, most major chapters are revised and some of them are totally rewritten. The chapter for merge, diverge, and small weaving segments is rewritten in accordance with forthcoming developments in the past 10 years. In this paper, an overview of the chapter in the new German Highway Capacity Manual is presented. Procedures dealing with performance analyses and level of service (LOS) of those segments are introduced both for freeways and rural highways. Differences between the former version and the new version of the chapter in the German Highway Capacity Manual are indicated and discussed. In most of the existing highway capacity manuals, LOS of merge, diverge, and small weaving segments is traditionally defined by speed, volume, or density in critical areas. In that traditional concept several capacity values of different critical areas (merge, diverge, and weaving) as well as upstream and downstream basic segments within the influence areas are evaluated separately. In the new HBS 2015, a new model which considers the total merge, diverge, and weaving segment as an entire object is incorporated. A combined volume-to-capacity ratio (freeways) or a combined density (rural highways) is used for defining the LOS of the total segment. The parameters of the new procedure are functions of the number of lanes of the major road, the number of lanes in the on-ramp or off-ramp, and the predefined geometric design of those segments. The coefficients are calibrated with field data or defined by experts" experiences within a matrix of coefficients. With those procedures, the traffic quality (LOS) can be obtained directly as a function of the volumes or densities on the major road and on the on-ramp or off-ramp respectively. The new procedure has the following advantages: a) a uniform function for all types of merge, diverge, and small weaving segments, b) traffic quality assessment for all critical areas under investigation in one step, and c) the procedure can easily be calibrated. For applications in practice, a set of graphs is provided.
With the introduction of the German Highway Capacity Manual (HBS) in January 2002 (FGSV, 2002), all methods for the evaluation of the performance of highway facilities were, for the first time in Germany, simultaneously updated and consolidated in a single work following the ideas of the American Highway Capacity Manual (HCM). This paper gives an overview of the new 2015 edition of the German HBS and describes the changes as for example the addition of chapters for freeway, rural roads, and major urban street facilities, comprising segments and intersections.
The paper describes the development of transitions between different safety barriers in Germany but also in the context of the European standardization. In the paper practical and impact test expriences with transitions are shown. In view of the sheer number of theoretically possible combinations of safety barriers, the demand for testing every transition, even if the connecting safety barriers differ only slightly, appears to be economically unacceptable. On the other hand the experience from accidents and also from failed impact tests shows that transitions can be a risk to traffic safety. Therefore criteria for the distinction between transitions (impact test required/impact test unnecessary) are explained. In order to distinguish transitions which do not have to be impact-tested from those that require impact tests, criteria were developed and formulated.
Rural roads (highways) in Germany have to provide both high road safety and an appropriate level of service in accordance with their function in the road network. Single carriageway rural roads often underperform these expectations. An analysis of severe accidents on rural roads found two main contributing factors. First, high or inappropriate speed leads to accidents caused by the loss of control of the vehicle. Second, unsafe passing manoeuvres related to a misjudgement of sight distance, speed of oncoming vehicles or a misjudgement of the driver vehicle's acceleration capability. On the five roads where unsafe passing manoeuvres were a main contributing factor to accident occurrence, single short passing lanes (600 m to 1.2 km) were built to provide safe passing. On the remaining two-lane sections passing was prohibited by road signs and road marking. This paper investigates the effect of this design change on the accident situation and on traffic flow. The research project is based on a before/after comparison of traffic and accident data. Traffic volume, vehicle types and their velocities as well as the time gaps between the vehicles were recorded at different cross-sections. The result shows a significant improvement in road safety. This improvement was especially noted for severe head-on crashes, which were reduced to almost zero. The analysis of traffic flow on these roads pointed out that the chosen lengths of passing lanes were sufficient for safe passing and thereby reduced the need for dangerous driving behaviour. The recommendations of this research were fundamental for the determination of the design parameters of the second highest design class (EKL 2) in the new German Rural Road Design Guideline (RAL) published in spring 2013.
Non-point sources of traffic-related pollution become a major concern as they " compared to the point-source inputs " are more difficult to be defined or controlled. It is crucial to evaluate the fraction of traffic-related contamination that is transported to the road surroundings as it could negatively impact soil, surface water and groundwater. This study describes two means through which pollutants leave the road to the surrounding environment. Three German motorways were selected (A4, A555, and A61), where runoff and deposits were analyzed to determine pollutant load moving into the roadside soil or into the drainage system. Each of the three motorways carries approximately 70,000 vehicles a day on 4 to 6 driving lanes; and they cover a broad range of truck participation in the total traffic load ranging from 5.4% to 19.8%. The three motorways represent several topographical and landscape features as forest with noise barrier and parallel as well as perpendicular orientation to the main wind direction. Sampling of runoff and deposition was done on monthly basis. Bulk deposition was collected in Bergerhoff vessels at two heights (1.5 m and 0.3 m above the ground) and in 1 m, 2.5 m, 5 m and 10 m distances from the road edge. The results showed that heavy metals as well as large amounts of mineral compounds are moving from the driving lanes into the roadside environment. This includes sodium from applying deicing salts in winter seasons, which could be found in soil, dust and water samples. Calcium and iron were also detected in almost comparable concentrations. The annual deposition flow (bulk deposition) measured at a height of 1.5 m was higher than the comparative values for urban areas and background measuring points. The spatial distribution of material deposition showed clear differences between the three motorways. The pollutant load in deposition measured near the ground surface was higher than those measured at 1.5 m above the land surface. At all three sites, a clear negative correlation between pollutant load and the distance from the roadside could be found. Nearly 90% of the concentration values of heavy metals in road runoff were below or in the range of the test values for seepage water in the German Soil Protection and Contamination Ordinance. The pH-values around 7 in runoff and adjacent soil provide a good retention capacity in the soil for the heavy metal input.
The German Federal Ministry of Economics and Technology is funding a projectrncalled "Leistra2" with the aim of understanding the tire road contact and to find measures to reduce traffic noise, in particular to reduce the noise of tires rolling on pavements, i.e. tire-road noise. The project is composed out of three mayor subjects, low noise tires, low noise pavements and verification of the results, each made out of single sub-projects. The purpose of this paper is to give a survey about Leistra2 and to report about the latest activities and results. More detailed information and contact data of the partners involved can be found at http://www. LeiStra2.de. The program is the successor of the program LeiStra (Leiser Strassenverkehr), dealing with similar topics.rn
The high density of commercial freight transport on motorways makes it difficult for truck drivers to find safe parking places especially for longer rest periods during the night. Even though expansions have been made to satisfy the demand in Germany, overcrowding and dangerous situations still occur as a result of vehicles parking on the entrance and exit roads of rest areas. In 2005 a control procedure called "Convoy Parking" was installed at the rest area Montabaur on the A3 motorway in Germany. Convoy Parking is subject to a patent (EP 1 408 455 B1, 2007). Convoy Parking requires all drivers entering their departure time at a terminal in front of a barrier. Subsequently, on the basis of the input data, the automatically detected vehicle length and the actual situation at the rest area, a free parking row is assigned and trucks can be parked sorted. The German Federal Highway Research Institute (BASt) developed a new control procedure called "Intelligent Controlled Compact Parking" (hereafter referred to as "Compact Parking" for short) to achieve that trucks are parking in a compact way, side by side and without a driving lane between trucks. Convoy Parking and Compact Parking have a very different control procedure and appearance. While Convoy Parking assigns a parking row to the driver, Compact Parking deliberately leaves the choice of the parking row to the drivers themselves. Drivers do not have to disclose their departure time to any system and they are not stopped by any barrier because Compact Parking offers a wide range of departure times on variable message signs. Drivers ought to use the parking row where their intended departure time is offered. With the innovative system Compact Parking the capacity of an existing rest area can be quickly increased without enlarging the area. This also avoids long-term planning approval procedures and is friendly to the environment. Besides, the safety for all users of the rest area can be improved by reducing illegal parking. Compact Parking is supported by the German Federal Ministry of Transport and Digital Infrastructure (BMVI). The first installation of Compact Parking is under construction at the rest area Jura-West on the A3 motorway (Northern Bavaria). The Autobahndirektion Nordbayern (Motorway Directorate for Northern Bavaria) is the central agency to plan, build and run the motorways in Northern Bavaria and got the approval of the BMVI to realize the pilot project. BASt accompanies the pilot project and leads the implementation of the control procedure. The opening is scheduled for summer 2015.
According to an investigation in March 2008 by the Federal Ministry of Transport, Building and Urban Affairs (BMVBS) about 14,000 truck parking spaces are missing in the near of motorways in Germany. Beside constructional enlargement of rest areas, intelligent traffic systems ought to be used to detect automatically the occupancy rate of rest areas and to provide better demand management and also to achieve an increase of capacity of truck parking spaces. The essay describes the newly developed control procedure "Compact parking", which is currently under development by German Federal Highway Research Institute (BASt). The method achieves that a number of trucks are parking in a compact way, side by side and without a driving lane between them. With the help of dynamic displays above the parking rows, the drivers receive the needful information to park their vehicle in a parking row, in which other trucks have the same or an earlier departure time. This system is able to increase the rest area capacity in short-term, more quickly than constructional enlargement of rest areas.
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
This article reports on a two-year study (2006 to 2008) of the distribution of de-icing salts (NaCl) applied to the road and the influence of traffic on the effective times of the de-icing salts. The research was focused on the needed resting periods of de-icing salts on road surfaces. The study used sensors installed in two lanes of the Motorway A4 in the area of the Dresden-Hellerau Highway Surveillance Center (Germany), to measure air and ground temperatures, wind speed and direction, liquid film thicknesses and residual quantities of salt on the road surface during ongoing traffic at 5-minute intervals. The authors conclude with four observations that can be useful for applying de-icing salts more judiciously: preventive spreading is only sensible if applied timely, i.e. immediately prior to icing events to be expected; the time-frame for preventive spreading on the dry road surface is maximum 60 minutes and on the moist road surface maximum 120 minutes; by increasing spreading densities in preventive spreading, this timeframe cannot be extended; it is completely sufficient if the spreading width is adjusted in such a way that the outer wheel tracks are also covered by the spreading. Distribution across the entire width of the lane will be caused by the rolling traffic within a few minutes.