91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (109)
- Buch (Monographie) (60)
- Wissenschaftlicher Artikel (5)
- Bericht (5)
- Teil eines Buches (Kapitel) (3)
- Arbeitspapier (1)
Schlagworte
- Deutschland (89)
- Germany (89)
- Conference (79)
- Konferenz (78)
- Safety (53)
- Sicherheit (52)
- Research report (45)
- Forschungsbericht (44)
- Bewertung (39)
- Evaluation (assessment) (38)
Institut
- Sonstige (183) (entfernen)
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Today's volumes of traffic require more and more responsibility from each individual road user in their interactions. Those who drive motor vehicles have the singular obligation to minimise the risk of accidents and hence the severity of injuries, particularly with a view to the most vulnerable road users such as motor bikes, bikes and pedestrians. Since responsible and pro-active driving depends first and foremost on the visual information relayed by our eyes and the visual channel this requires good command of the traffic and all-round visibility from our driver's seat. Granted that human error can never be fully excluded, improving visibility around the car is nevertheless an urgent priority. To do so, we need to rate visibility in the most realistic driving situations. Since the existing visibility metrics and methodology are not applicable to real-life driving situations, this study aimed at developing a new visibility rating methodology based on real-life accident scenarios. On the basis of the cases documented by the accident research project, this study analysed criteria indicative of diminishing visibility on the one hand and revealing some peculiarities in connection with the visibility issue on the other. Based on the above, the project set out to develop a rating methodology allowing to assess all-round visibility in various road situations taking into account both driver and road geometries. In this context, the assessment of visibility while turning a corner, crossing an intersection and joining traffic on a major road (priority through route) is of major importance. The first tests have shown that critical situations can be avoided by adapting the relevant geometries and technical solutions and that significant improvements of road safety can be derived therefrom.
Im Rahmen dieser Begleitstudie zum Feldversuch mit Lang-Lkw wurde untersucht, wie die technischen Anforderungen der Verordnung über Ausnahmen von straßenverkehrsrechtlichen Vorschriften für Fahrzeuge und Fahrzeugkombinationen mit Überlänge (LKWÜberlStVAusnV) von teilnehmenden Speditionen umgesetzt wurden. Die Studie fußt auf den der BASt von den am Feldversuch teilnehmenden Speditionen zur Verfügung gestellten Daten sowie Fahrzeugbegutachtungen und Fragebögen. Sie bildet den Stand vom 23.06.2016 mit 147 Lang-Lkw von 58 Speditionen ab. 80 Lang-Lkw vom Typ 3 bilden hierbei den größten Anteil. Alternative Umsetzungsmöglichkeiten technischer Anforderungen wurden speziell bei Achslastüberwachungssystemen, Kamera-Monitor-Systemen am Heck und der Tauglichkeit für den Kombinierten Verkehr betrachtet. Bei den Achslastüberwachungssystemen zeigte sich, dass sich bei 80 % der Fahrzeuge alle Achslasten komfortabel direkt im Fahrerhaus ablesen lassen. Kamera-Monitor-Systeme am Heck werden von den Feldversuchsteilnehmern überwiegend als praxistauglich bewertet und insbesondere als Rangierhilfe positiv aufgenommen. Bei Bremswegmessungen zeigte sich, dass auf ihr zulässiges Gesamtgewicht von 40 t beladene Lang-Lkw einen geringfügig längeren Bremsweg aufweisen als Sattelzüge, die mit der gleichen Ladungsdichte, jedoch weniger Ladung auf ca. 28 t Gesamtgewicht volumetrisch voll beladen sind. Bei ganzheitlicher Betrachtung sowohl der Vorgängerstudie als auch dieser Studie kann jedoch von vergleichbaren Bremswegen von Lang-Lkw im Vergleich zu Lkw herkömmlicher Bauart ausgegangen werden. Die Wirksamkeit von Fahrdynamikregelsystemen bei Lang-Lkw wurde im Rahmen von Literaturrecherchen sowie Experten- und Herstellerinterviews untersucht. Die Auslegung der Systeme ist so gestaltet, dass sie den Lang-Lkw verlässlich stabilisieren und zur Fahrzeugsicherheit von Lang-Lkw beitragen.
Die Schwerpunkte dieses Projekts lagen in der Untersuchung der Fahrerverfügbarkeit und Müdigkeit sowie in der Herstellung natürlichen Verhaltens bei längeren hochautomatisierten Fahrten. Es konnte im Rahmen von zwei Fahrsimulationsversuchen mit 15 und 42 Probanden gezeigt werden, dass bei hochautomatisierten Fahrten von 60 Minuten Müdigkeit auftreten kann, bei Ausprägung und Zeitpunkt des Auftretens jedoch große individuelle Unterschiede bestehen. Da eine zu kleine Stichprobe sich zum Zeitpunkt der Übernahme in einem entsprechend müden Zustand befand, kann die Auswirkung von Müdigkeit auf das Übernahmeverhalten nicht abschließend beurteilt werden. Hierfür empfehlen sich für die Zukunft Studien mit einem zustandsabhängigen Versuchsdesign. Der Einsatz von natürlichen fahrfremden Tätigkeiten, mit denen die Probanden sich frei beschäftigen durften, zeigte sowohl in der Probandstudie im Fahrsimulator als auch bei einem Expertenworkshop im Realfahrzeug eine hohe Involviertheit der Probanden in die Tätigkeiten während der gesamten 60 Minuten hochautomatisierten Fahrens. Es wird vermutet, dass dies auf die hohe intrinsische Motivation und den hohen Unterhaltungswert der selbstgewählten Aktivitäten zurückzuführen ist. Es zeigte sich außerdem, dass die Wahl der Tätigkeit vom Alter der Probanden abhängig ist. Eine Fahrtdauer von 60 Minuten wurde aufgrund der Ergebnisse aus allen drei Versuchen als realistisches Zukunftsszenario eingestuft und besitzt daher eine hohe Relevanz. Sowohl für die Bewertung von Müdigkeit als auch von Ablenkung war das Blickverhalten am meisten aufschlussreich. Für die Bewertung von Müdigkeit während der Beschäftigung mit fahrfremden Tätigkeiten wird jedoch ein kopfbasiertes Blickerfassungssystem, welches in der Lage ist, den Augenöffnungsgrad zu erfassen, oder videobasierte Verhaltensbeobachtung empfohlen.
Ziel des Forschungsvorhabens war es, durch gezielte Auswertung des Unfallgeschehens den Einfluss von Fahrerverhaltensweisen beziehungsweise -merkmalen und technischen Fahrzeugparametern auf die Unfallhäufigkeit und die Unfallart zu ermitteln. Zunächst wurde eine Auswertung der Literatur und die Beschaffung und Aufbereitung des Datenmaterials vorgenommen. Die Grundlage der Auswertungen bildeten die Unfälle mit Pkw-Beteiligung im Bundesland Nordrhein-Westfalen aus dem Jahre 1980. Die Datensätze waren vom Kraftfahrt-Bundesamt in Flensburg um fahrzeugtechnische Angaben erweitert worden. Zur Relativierung der Unfallzahlen wurden fahrzeugtypenspezifische jährliche Fahrleistungen und Bestände berechnet. Weiterhin wurde das Geschwindigkeitsverhalten im freien Verkehr in Abhängigkeit vom Fahreralter sowie vom Fahrzeugtyp ermittelt. Um die Wechselwirkungen von Fahrer- und Fahrzeugeigenschaften im Unfallgeschehen unabhängig voneinander betrachten zu können, war es notwendig, einen "Normalfahrer" zu definieren. Der "Normalfahrer" wurde anhand von Analysen ausgewählter Unfallsituationen mit dem Ziel beschrieben, mit diesen Fahrern Fahrversuche mit Pkw durchführen zu können, deren Ergebnisse weder durch besonders gute noch durch besonders schlechte, sondern vielmehr durch eine durchschnittliche Eignung des Fahrers zum Führen eines Kraftfahrzeuges geprägt sein sollen. Anhand dieser Fahrversuche sollen Grenzen von Kennwerten, die Fahrzeugeigenschaften und das Fahrverhalten beschreiben, abgeleitet werden, die sich als dem "Normalfahrer" angepasst erweisen. Aufgrund der aufgezeigten Zusammenhänge zwischen dem Fahreralter und der ursächlichen Beteiligung an bestimmten Unfalltypen ist es nunmehr möglich, durchschnittlich gute Fahrer als Probanden auszuwählen, die je nach Art des Versuches entweder zur Gruppe der jüngeren und älteren Fahrer gehören. Nach vorheriger Festlegung eines Anteilswertes von Fahrern, die als "normal" anzusehen sind, können bei gleichzeitiger Berücksichtigung der für jüngere und ältere Fahrer typischen Versagensarten die Altersintervalle bestimmt werden, aus denen die "Normalfahrer" für die Fahrversuche auszuwählen sind.
The paper gives an overview of the recent (mostly 2012) figures of killed bus/coach occupants (drivers and passengers) in 27 Member States of the European Union as reported by CARE. The Evolution of the figures of bus/coach occupants killed in road accidents urban, rural without motorway and on motorways from 1991 to 2010 in 15 Member States of the EU supplements this information. More detailed are the figures reported for Germany by the Federal Statistics. The paper displays long-term evaluations (1957 to 2012) for killed, seriously and slightly injured occupants in all kinds of buses/coaches. Midterm evaluations (1995 to 2012) of the figures of fatalities and casualties are displayed for different busses according to their identification of road using as coaches, urban buses, school buses, trolley buses and "other buses". To be able to compare the evolutions of the safety of vehicle occupants it is customary to use different risk indicators. Calculations and illustrations for three often used indicators with their development over time are given: fatalities, seriously injured and slightly injured per 100,000 vehicles registered, per 1 billion (109) vehicle-kilometres travelled and per 1 billion (109) person-kilometres. These indicators are shown for occupants of cars, goods vehicles and buses/coaches. For the period from 1957 until 2012 it is obvious, that for all three vehicle categories analysed there was a clear long-term trend towards more occupant safety in terms of casualties per vehicles registered and per vehicle mileage. This was most significant for car occupants but it can be seen for bus/coach occupants and goodsvehicle occupants as well. Figures of killed occupants and of casualties related to person-kilometres are calculated and displayed for the shorter period 1995 to 2012. Here it becomes obvious that the bus/coach is still the safest mode of transport for the occupants of road vehicles. Graphs for the casualty risk indices still show significantly higher risks for car occupants despite the corresponding curve moved sustainable downwards. It is remarkable, that the risks of being killed or injured for the occupants of urban buses is growing whereas the corresponding risk for the occupants of coaches in line traffic tends downwards. The article ends with a short comparison and discussion of the risk indicators which are actually published for the occupants (driver and passengers) of cars and the passengers of buses/coaches, railroads, trams and airplanes. The interpretation of such information depends on the perception and it seems that for a complete view not only one indicator should be used and the evolutions of the indicator values during longer periods (as displayed with examples in the paper) should also be taken into account.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.
Providing effective occupant protection in rollover crashes requires supplying the occupant with a restraint system proven effective in the dynamic rollover accident mode. Preventing ejection and providing restraint sufficient to prevent potentially injurious contacts with both interior and exterior vehicle components is paramount for effective rollover occupant protection. Research has shown that the injury potential can be decreased by closely coupling the occupant to the seat. This paper focuses on the effect of restraint system slack and its relationship to occupant excursion and ejection potential during rollover. Various restraint system configurations are evaluated in rollover-type test environments. A review of prior research is presented prior to presenting new quasi-static vehicle inversion studies conducted with live surrogate occupants. Additionally, dynamic rollover testing utilizing anthropometric test devices (ATDs) is presented. The influence of belt looseness and effects of various restraint designs on the belted occupants' injury potential are discussed.